Scribd
Upload
22 views

Overcurrent Relays: K Equal To Zero. Therefore, The Equation Becomes

Overcurrent relays provide protection against excess current in electrical systems. There are three types of overcurrent relays: definite current/instantaneous relays which operate immediately when current reaches a set value, definite time relays which operate after a set time delay, and inverse time relays where the operating time is inversely proportional to the fault current. Inverse time relays are commonly used and their characteristics indicate the speed of operation. Relay settings like pickup current and time multiplier are determined based on factors like overload level and circuit ratings to provide discrimination of protection zones.

Uploaded by

Mukhtiar Hussain
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
22 views

Overcurrent Relays: K Equal To Zero. Therefore, The Equation Becomes

Overcurrent relays provide protection against excess current in electrical systems. There are three types of overcurrent relays: definite current/instantaneous relays which operate immediately when current reaches a set value, definite time relays which operate after a set time delay, and inverse time relays where the operating time is inversely proportional to the fault current. Inverse time relays are commonly used and their characteristics indicate the speed of operation. Relay settings like pickup current and time multiplier are determined based on factors like overload level and circuit ratings to provide discrimination of protection zones.

Uploaded by

Mukhtiar Hussain
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Overcurrent Relays

• Protection against excess current was naturally the earliest protection systems to evolve

• From this basic principle has been evolved the graded over current system, a discriminate
fault protection.

• “over current” protection is different from “over load protection”.


• Overload protection makes use of relays that operate in a time related in some degree to
the thermal capability of the plant to be protected.

• Over current protection, on the other hand, is directed entirely to the clearance of the
faults, although with the settings usually adopted some measure of overload protection is
obtained.

• In terms of the general torque equation the over current relay has both constants K2 and
K3 equal to zero. Therefore, the equation becomes

T  K1 I 2  K4

1.Types of over current relays

• Based on the relay operating characteristics , overcurrent relays can be classified into
three groups

– Definite current or instantaneous


– Definite time
– Inverse time

DEFINITE-CURRENT RELAYS

• This type of relay operates instantaneously when the current reaches a predetermined
value.
DEFINITE TIME CURRENT RELAYS

• This type of relay operates after a definite time when the current reaches a pre-
determined value.

INVERSE TIME RELAYS

• The fundamental property of these relays is that they operate in a time that is inversely
proportional to the fault current. Inverse time relays are generally classified in accordance
with their characteristic curve that indicates the speed of operation.

• Inverse-time relays are also referred as inverse definite minimum time or IDMT over
current relays

SETTING THE PARAMETERS OF TIME DELAY OVERCURRENT RELAY

Pick-up setting

The pick-up setting, or plug setting, is used to define the pick-up current of the relay, and
fault currents seen by the relay are expressed as multiples of plug setting.

• Plug setting multiplier (PSM) is defined as the ratio of the fault current in secondary
Amps to the relay plug setting.

• For phase relays the pick-up setting is determined by allowing a margin for overload
above the nominal current, as in the following expression

Pick-up setting = (OLF x Inom) / CTR

Where, OLF = Overload factor that depends on the element being protected.

Inom = Nominal circuit current rating, and CTR = CT Ratio

Time dial setting

• The time-dial setting adjusts the time –delay before the relay operates whenever the fault
current reaches a value equal to, or greater than the relay setting.

• The time-dial setting is also referred to as time multiplier setting (TMS)


DISCRIMINATION BY TIME

In this method an appropriate time interval is given by each of the relays controlling the CBs
in a power system to ensure that the breaker nearest to the fault location opens first.
A simple radial distribution system is considered to illustrate this principle

A radial distribution system with time-discrimination

• The main disadvantage of this method of discrimination is that the longest fault clearance
time occurs for faults in the section closest to the power source, where the fault level is
highest.

DISCRIMINATION BY CURRENT

• Discrimination by current relies on the fact that the fault current varies with the position
of the fault, because of the difference in impedance values between the source and the
fault.

• The relays controlling CBs are set to operate at suitably tapered values such that only the
relay nearest the fault trips its circuit breaker.

Inverse time over current relay characteristic is evolved to overcome the limitations imposed by
the independent use of either time or over current coordination.

You might also like