Scribd
Upload
75 views10 pages

Set-Up Computer Networks Setting-Up Computer Networks

This document outlines a training module for setting up computer networks. The module is 40 hours and covers installing network cables, configuring network and router/WiFi settings, and inspecting and testing the completed network. Upon completion, trainees will be able to install cables, set network and device configurations, and ensure the network is functioning properly and safe. The module provides learning objectives, content outlines, equipment requirements, and assessment methods for each competency.

Uploaded by

palogjohnjr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
75 views10 pages

Set-Up Computer Networks Setting-Up Computer Networks

This document outlines a training module for setting up computer networks. The module is 40 hours and covers installing network cables, configuring network and router/WiFi settings, and inspecting and testing the completed network. Upon completion, trainees will be able to install cables, set network and device configurations, and ensure the network is functioning properly and safe. The module provides learning objectives, content outlines, equipment requirements, and assessment methods for each competency.

Uploaded by

palogjohnjr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

UNIT OF COMPETENCY : SET-UP COMPUTER NETWORKS

MODULE TITLE : SETTING-UP COMPUTER NETWORKS

MODULE DESCRIPTOR : This module covers the outcomes required in setting-up


computers networks for LANs and SOHO systems. It
consists of competencies to install network cables, set
network configuration, set router/Wi-Fi/ wireless access
point/repeater configuration as well as to inspect and test
the configured computer networks.

NOMINAL DURATION : 40 hours

QUALIFICATION LEVEL : NC II

SUMMARY OF LEARNING OUTCOMES:

Upon completion of this module, the trainee/student must be able to:

LO1. Install network cables

LO2. Set network configuration

LO3. Set router/Wi-Fi/ wireless access point/repeater configuration

LO4. Inspect and test the configured computer networks


LO1. INSTALL NETWORK CABLES

ASSESSMENT CRITERIA:

1 Cable routes are determined and planned in accordance with network design
and actual installation site.
2 Network materials necessary to complete the work are identified and obtained
in accordance with established procedures and checked against systems
requirements
3 Tools, equipment and testing devices needed to carry out the installation work
are obtained in accordance with established procedures and checked for
correct operation and safety
4 Appropriate personal protective equipment is used and OHS policies and
procedures are followed
5 Copper cable splicing is performed based on Electronic Industries Alliance/
Telecommunications Industry Association (EIA/TIA) standards
6 Network cables and cable raceway are installed in accordance with established
procedures and installation requirements
7 Installation work is performed and is checked to ensure no unnecessary
damage has occurred and complies with requirements
8 5S and 3Rs are followed according to environmental policies

CONTENTS:

 Computer networking concepts


o Open system interconnection (OSI) model
 Physical layer
 Data link layer
 Network layer
 Transport layer
o Network components
 Computer system
 Media
- Wired or wireless
 Protocol
 Interface / Network devices
- Hubs, Switches, Routers and Bridges
o Network topology
o Types of networks
 Size/geographical
- Local area network (LAN)
- Wide area network (WAN)
 Role
- Peer-to-peer
- Client Server
 Network cable installation
o Types of cable
 Unshielded Twisted Pair/Shielded Twisted Pair (UTP/STP)
 Coaxial
 Fiber optic
o Copper cable splicing standards
 Straight-through
 Cross-over
o Fiber optic cable installation
o Copper cable standards
 CAT5, CAT5e and CAT6
 Roughing- in activities
o Installation of cable raceways/ducts
o Installation of modular panel/box
o Installation of patch panel
 Cable testing
 Principles of 5S and 3Rs

CONDITIONS:

The students/trainees must be provided with the following:

 PC or workstation
 Access to network cable installation board
 Ladder
 PPEs (i.e. goggles, gloves, safety shoes, working clothes, etc.)

Network materials Tools and test instruments


 Network cables  Crimping tool
- UTP CAT5e  Side-cutting pliers
- UTP CAT6  Screwdriver set
- STP CAT5  Portable hand drill with bit set
- Terminated fiber optic cables  Hammer
 Slotted PVC  Hacksaw
 Modular box/panel  Pull-push rule
 Patch panel  Tool holster
 Cable organizer kit  LAN tester
 RJ 45
 Fastener (i.e. screw, hole-filler/tox)

METHODOLOGIES:

 Lecture/ Discussion
 Demonstration
 Viewing multimedia

ASSESSMENT METHODS:
 Written exam
 Practical exam/demonstration
 Observation in workplace
LO2. SET NETWORK CONFIGURATION

ASSESSMENT CRITERIA:

1 Network connectivity of each terminal is checked in accordance with network


design.
2 Any fault or problem in the network system is diagnosed and remedied in line
with the standard operating procedures.
3 Network interface card (NIC) settings are configured in accordance with
network design.
4 Communication checking between terminals are carried out in accordance with
OS network configuration guides
5 Unplanned events or conditions are responded to in accordance with
established procedures

CONTENTS:

 Network design
o Data packet principles
o IP address configuration
 IPV4
 IPV6
o Subnet configuration
o Procedures in configuring Network interface card (NIC) for network
communication
 Protocol
 IP address
 Subnet mask
 Gateway
 Network configuration
o Peer-to-peer cross-over connection
o Peer-to-peer using switch
 Network connectivity testing
o Wizard–based testing
o Command line interface testing

CONDITIONS:

The students/trainees must be provided with the following:

 2 units desktop computers


 Laptop
 Terminated network cables
 Switch
 Access to installed network cables
METHODOLOGIES:

 Lecture/ Discussion
 Demonstration
 Viewing multimedia

ASSESSMENT METHODS:
 Written exam
 Practical exam/demonstration
 Observation in workplace
LO3. SET ROUTER/WI-FI/ WIRELESS ACCESS POINT/REPEATER
CONFIGURATION

ASSESSMENT CRITERIA:

1 Client Device systems settings are configured in accordance with


manufacturers’ instructions and end-user preferences
2 Local area network (LAN) port is configured in accordance with manufacturers’
instructions and network design
3 Wide area network (WAN) port is configured in accordance with manufacturers’
instructions and network design
4 Wireless settings are configured in accordance manufacturers’ instructions,
network design and end-user preferences
5 Security/Firewall/Advance settings are configured in accordance with
manufacturers’ instructions and end-user preferences

CONTENTS:

 Router/Wi-Fi/ wireless access point/repeater configuration


 Network interface card (NIC) settings
 Device systems settings configuration
 Local area network (LAN) port configuration
 Wide area network (WAN) port configuration
 Wireless settings configuration
 Security/Firewall/Advance settings and configuration
 Cloud computing

CONDITIONS:

The students/trainees must be provided with the following:

 2 units desktop computers


 Laptop
 Terminated network cables
 Switch
 Access to installed network cables
 Router/Wi-Fi/ wireless access point/repeater

METHODOLOGIES:

 Lecture/ Discussion
 Demonstration
 Viewing multimedia
ASSESSMENT METHODS:
 Written exam
 Practical exam/demonstration
 Observation in workplace
LO4. INSPECT AND TEST THE CONFIGURED COMPUTER NETWORKS

ASSESSMENT CRITERIA:

1 Final inspections are undertaken to ensure that the configuration done on the
computer networks conforms with the manufacturer’s instruction/manual
2 Computer networks are checked to ensure safe operation.
3 Reports are prepared/completed according to company requirements.

CONTENTS:

 Network connectivity testing


 Documentation procedures
 Philippine Electrical Code relevant to data connection
 Principles of 5S and 3Rs

CONDITIONS:

The students/trainees must be provided with the following:

 2 units desktop computers


 Laptop
 Terminated network cables
 Switch
 Access to configured computer network systems
 Router/Wi-Fi/ wireless access point/repeater
 Tools and test instruments
 PPEs

METHODOLOGIES:

 Lecture/ Discussion
 Demonstration
 Viewing multimedia

ASSESSMENT METHODS:
 Written exam
 Practical exam/demonstration
 Observation in workplace

You might also like