NFW-100X Intelligent Addressable FACP with Communicator

General
The FireWarden-100X (NFW-100X) is the latest intelligent address-
able Fire Alarm Control Panel (FACP) within the FireWarden Series
and is a direct replacement for the FireWarden-100 (NFW-100). The
NFW-100X comes with a pre-installed communicator and supports
up to 198 addressable devices (99 detectors and 99 modules). With
an extensive list of powerful features, the NFW-100X programs just
like FireWarden-100 products, yet fits into applications previously
served only by conventional panels.
The pre-installed IPOTS-COM is a dual technology (POTS and IP)
communicator. The POTS transmits system status (alarms, troubles,
AC loss, etc.) to a Central Station via the public switched telephone
network. The IP communicator’s internet monitoring capability sends
alarm signals over the Internet saving the monthly cost of two dedi-
cated business telephone lines. Although not required, the second-
ary telephone line may be retained providing backup communication
over the public switched telephone line. Optional cellular reporting is
available using the CELL-MOD or CELL-CAB-N.
Remote and local programming of the control panel is possible using
the FS-Tools Upload/Download utility. Programming databases can
be uploaded/downloaded via the panel’s USB port (and USB cable)
or via an ethernet connection using the IPOTS-COM communicator.
The USB port also allows for the download or upload of the entire
program, history file, walk-test data, current status and system volt-
ages by means of a USB flash drive.
• Maintenance alert warns when smoke detector dust accumula-
The power supply and all electronics are contained on a circuit tion is excessive
board supported on a new quick install chassis and housed in a • One-person audible or silent walk test with walk-test log and
metal cabinet. Available accessories include local and remote printout
upload/download software, remote annunciators, and reverse polar- • System alarm verification selection per detector point
ity/city box transmitter (4XTM). • PAS (Positive Alarm Sequence) and Pre-signal per point (NFPA
Features 72 compliant)
• Up to 16 ANN-BUS annunciators- 8 per each ANN-Bus
• Listed to UL Standard 864, 10th edition • Remote Acknowledge, Alarm Silence, Reset and Drill via
• Pre-installed IPOTS-COM Ethernet IP and POTS (Plain Old Tele- addressable modules or remote annunciator
phone Service) Central Station Communicator over AlarmNet • Upload/Download of program and data via USB with optional FS-
• Optional CELL-MOD or CELL-CAB-N GSM Central Station Com- Tools Programming Utility
municator over AlarmNet®
• Automated activation of the NFC-50/100 Emergency Command SLC COMMUNICATION LOOP
Center • Supports FlashScan® and CLIP protocols
• NFC-FFT Firefighter Telephone option • SLC operates up to 10,000 ft. (3,000 m) in FlashScan mode with
• Compatible with SWIFT® wireless devices twisted, unshielded wire
• Auto-programming (learn mode) reduces installation time.
• Single addressable SLC loop which meets NFPA Class B and
Reports two devices set to the same address
Class A requirements
• Four built-in, independently programmable Style Z (Class A) or
Style Y (Class B) NAC circuits • 198 addressable device capacity (99 addressable detectors and
• Selectable strobe synchronization for System Sensor, Wheelock, 99 modules)
and Gentex devices • Compatible with NOTIFIER FireWarden and ONYX Series
• Notification Appliance Circuit End of Line resistor matching addressable devices (refer to the FireWarden SLC Wiring Man-
• Four programmable function keys for ease of maintenance ual)
• Two programmable relays and one fixed trouble relay NOTIFICATION APPLIANCE CIRCUITS (NACS)
• Built-in Programmer
• Integral 80-character LCD display with backlighting • Four independently programmable output circuits. Circuits can be
• Real-time clock/calendar with automatic daylight savings control configured for the following outputs:
• History file with 1,000 event capacity – Style Y (Class B)
• Addressable sounder base compatibility – Style Z (Class A)
• Control module delay timer • Silence Inhibit and Autosilence timer options
• Automatic detector sensitivity testing (NFPA 72 compliant) • Continuous, March Time, Temporal, or California code for main
• Automatic device type-code verification circuit board NACs with two-stage capability
• Point trouble identification
• Selectable strobe synchronization per NAC
• Waterflow selection per module point
• Alarm verification selection per detector point • 2.5 A special application, 250mA regulated, total power for NACs
NOTE: Maximum or total 24VDC system power shared between all NAC
circuits and the ANN-BUS is 2.7 A
DN-60959:C • 7/16/2018 — Page 1 of 4
PROGRAMMING AND SOFTWARE vised output for local energy municipal box transmitter, alarm and
• Autoprogramming (learn mode) reduces installation time trouble. Includes a disable switch and disable trouble LED.
• Custom English labels (per point) may be manually entered or PWRMOD24 Power Expander Module: Optional power module.
selected from an internal library file Increases alarm power output to 6 amps.
• Two programmable Form-C relay outputs COMPATIBLE ANNUNCIATORS
• 99 software zones N-ANN-80: Remote LCD annunciator mimics the information dis-
• Continuous fire protection during online programming played on the FACP LCD display. Recommended wire type is un-
• Program Check automatically catches common errors not linked shielded. (Basic model is black; order -W for white; see DN-7114.)
to any zone or input point N-ANN-100R: Remote LCD annunciator mimics the information dis-
• OFFLINE PROGRAMMING: Create the entire program in your played on the FACP LCD display. Recommended wire type is un-
office using FS-Tools, a Windows®-based software package, and shielded. For use in FM applications only. (Basic model is black;
upload/download system programming locally. Offline program- order R for red.)
ming requires an ethernet connection. FS-Tools is available on N-ANN-I/O: LED Driver Module provides connections to a user sup-
www.notifier.com. plied graphic annunciator. (See DN-7105.)
N-ANN-LED: Annunciator Module provides three LEDs for each
User interface zone: Alarm, Trouble, and Supervisory. Ships with red enclosure.
(See DN-60242.)
LED INDICATORS
N-ANN-RLED: Provides alarm (red) indicators for up to 30 input
• Fire Alarm (red) • CO Alarm (red) zones or addressable points. (See DN-60242.)
• AC Power (green) • Supervisory (yellow) N-ANN-RLY: Relay Module provides 10 programmable Form-C
• Trouble (yellow) • Ground fault (yellow) relays. Can be mounted inside the cabinet. (See DN-7107.)
• Battery fault (yellow) • Disabled (yellow) N-ANN-S/PG: Serial/Parallel Printer Gateway module provides a
connection for a serial or parallel printer. (See DN-7103.)
• Maintenance (yellow) • Communication (yellow)
• Alarm Silenced (yellow) • F1-F4 Programmable Function ADDRESSABLE DEVICES
Keys (yellow) FSP-951: Addressable low-profile photoelectric smoke detector.
FlashScan only.
KEYPAD FSP-951-IV: Addressable low-profile photoelectric smoke detector.
• 16 key alpha-numeric pad • Acknowledge Ivory. FlashScan and CLIP mode.
• Alarm Silence • Drill (Manual Evacuate) NP-200: Addressable low-profile photoelectric smoke detector.
• Four (4) programmable function keys • Reset (lamp test) B300-6 base included, FlashScan only.
NP-200-IV: Addressable low-profile photoelectric smoke detector.
PRODUCT LINE INFORMATION Ivory, B300-6-IV base included. FlashScan and CLIP mode.
NFW-100X: Addressable Fire Alarm Control Panel with one SLC FSP-951T: Addressable low-profile photoelectric smoke detector
loop. Includes main circuit board with display chassis with trans- with thermal sensor. FlashScan only.
former, backbox with door, plastic bag containing screws, cables, FSP-951T-IV: Addressable low-profile photoelectric smoke detector
key, etc. with thermal sensor. Ivory. FlashScan and CLIP mode.
FS-Tools: Programming software for Windows®-based PC com- NP-200T: Addressable low-profile photoelectric smoke detector with
puter. Available for download at www.notifier.com. thermal sensor. B300-6 base included. FlashScan only.
CELL-CAB-N/CELL-MOD: Optional GSM communicators.
NP-200T-IV: Addressable low-profile photoelectric smoke detector
IPOTS-COM: Dual technology (POTS and IP) communicator. with thermal sensor. Ivory, B300-6-IV base included. FlashScan and
(replacement board) CLIP mode.
DP-ES-R: Optional dress panel for the NFW-100X (red).
FSP-951R: Remote test capable addressable photoelectric smoke
DP-ES-B: Optional dress panel for NFW-100X (black). detector for use with DNR(W) duct detector housing. FlashScan
TR-CE-B: Optional trim ring for semi-flush mounting. (Black. For only.
red, order TR-CE.) FSP-951R-IV: Remote test capable addressable photoelectric
BB-XP: Optional cabinet for one or two modules. smoke detector for use with DNR(W) duct detector housing. Ivory.
BB-25: Optional cabinet for up to six modules mounted on CHS-6 FlashScan and CLIP mode.
chassis. NP-200R: Remote test capable addressable photoelectric smoke
BB-26: Battery backbox, holds up to two 25 AH batteries and CHG- detector for use with DNR(W) duct detector housing. FlashScan
75. only.
NFS-LBB: Battery box, houses two 55 AH batteries NP-200R-IV: Remote test capable addressable photoelectric smoke
CHS-6: Chassis, mounts up to six multi-modules in a BB-25 cabinet. detector for use with DNR(W) duct detector housing. Ivory, FlashS-
CHG-75: Battery charger for lead-acid batteries with a rating of 25 to can and CLIP mode.
75 AH. FST-951: Low-profile 135°F fixed thermal sensor. FlashScan only.
CHG-120: Remote battery charging system for lead-acid batteries FST-951-IV: Low-profile 135°F fixed thermal sensor. Ivory. FlashS-
with a rating of 55 to 120 AH. Requires additional NFS-LBB for can and CLIP mode.
mounting. NH-200: Low-profile 135°F fixed thermal sensor. B300-6 base
NOTE: CHG-120 or CHG-75 required for batteries larger than 18AH. included, FlashScan only.
BAT Series: Batteries, see data sheet DN-6933. NH-200-IV: Low-profile 135°F fixed thermal sensor. Ivory. B300-6-IV
PRN Series: UL listed compatible event printer. Uses tractor-fed base included, FlashScan and CLIP mode.
paper. FST-951R: Low-profile, intelligent, rate-of-rise thermal sensor.
FlashScan only.
OPTIONAL MODULES
FST-951R-IV: Low-profile, intelligent, rate-of-rise thermal sensor.
4XTM Reverse Polarity Transmitter Module: Provides a super- Ivory. FlashScan and CLIP mode.

Page 2 of 4 — DN-60959:C • 7/16/2018

NH-200R: Low-profile 135°F fixed thermal sensor. B300-6 base zone of conventional two-wire detectors. Requires resettable 24
included, FlashScan only. VDC power. Refer to the Device Compatibility Document for listed
NH-200R-IV: Low-profile 135°F fixed thermal sensor. Ivory. B300-6- compatible devices and quantity limitation.
IV base included, FlashScan and CLIP mode. NZM-100: Similar to NMM-100. Addressable Monitor Module for one
FST-951H: Low-profile intelligent 190°F/88°C fixed thermal sensor. zone of conventional two-wire detectors. Requires resettable 24
FlashScan only. VDC power. Refer to the Device Compatibility Document for listed
compatible devices and quantity limitation.
FST-951H-IV: Low-profile intelligent 190°F/88°C fixed thermal sen-
sor. Ivory. FlashScan and CLIP mode. FCM-1: Addressable Control Module for one Style Y/Z (Class B/A)
zone of supervised polarized Notification Appliances. Mounts
NH-200H: Low-profile intelligent 190°F/88°C fixed thermal sensor.
directly to a 4.0" (10.16 cm.) electrical box. NAC option requires
B300-6 base included, FlashScan only.
external 24 VDC to power notification appliances.
NH-200H-IV: Low-profile intelligent 190°F/88°C fixed thermal sen-
NC-100: Addressable Control Module for one Style Y/Z (Class B/A)
sor. Ivory. B300-6-IV base included, FlashScan and CLIP mode.
zone of supervised polarized Notification Appliances. Mounts
Legacy Devices directly to a 4.0" (10.16 cm.) electrical box. NAC option requires
FSI-851: Addressable low-profile ionization smoke detector. external 24 VDC to power notification appliances.
NI-100: Addressable low-profile ionization smoke detector. FRM-1: Addressable relay module containing two isolated sets of
FSP-851: Addressable low-profile photoelectric smoke detector. Form-C contacts, which operate as a DPDT switch. Mounts directly
to a 4.0" (10.16 cm.) box, surface mount using the SMB500.
NP-100: Addressable low-profile photoelectric smoke detector.
NC-100R: Addressable relay module containing two isolated sets of
FSP-851T: Addressable low-profile photoelectric smoke detector
Form-C contacts, which operate as a DPDT switch. Mounts directly
with thermal sensor.
to a 4.0" (10.16 cm.) box, surface mount using the SMB500.
NP-100T: Addressable low-profile photoelectric smoke detector with NBG-12LX: Addressable manual pull station with interface module
thermal sensor. mounted inside.
FSP-851R: Remote test capable addressable photoelectric smoke NOT-BG12LX: Addressable manual pull station with interface mod-
detector for use with DNR(W) duct detector housing. ule mounted inside.
NP-100R: Remote test capable addressable photoelectric smoke ISO-X: Fault Isolator Module.
detector for use with DNR(W) duct detector housing.
N100-ISO: Fault Isolator Module.
FST-851: Fast-response, low-profile heat detector.
NH-100: Fast-response, low-profile heat detector. ISO-6: Six-fault isolator module. Mount one or two modules in a BB-
XP cabinet (optional). Mount up to six modules on a CHS-6 chassis
FST-851R: Fast-response, low-profile heat detector with rate-of-rise in a CAB-3/CAB-4 series cabinet.
option.
SMB500: Used to mount all modules except the FMM-101/NMM-
NH-100R: Fast-response, low-profile heat detector with rate-of-rise 100P.
option.
NMM-100-10: Ten-input monitor module. Mount one or two modules
FST-851H: Fast-response, low-profile heat detector that activates at in a BB-2F cabinet (optional). Mount up to six modules on a CHS-6
190°F/88°C. chassis in a BB-6F cabinet.
NH-100H: Fast-response, low-profile heat detector that activates at NZM-100-6: Six-zone interface module. Mount one or two modules
190°F/88°C. in a BB-XP cabinet (optional). Mount up to six modules on a CHS-6
FAPT-851: Addressable low-profile multi-sensor detector. chassis in a CAB-3/CAB-4 series cabinet.
NP-A100: Addressable low-profile multi-sensor detector. SWIFT Wireless Devices
B200S: Programmable, addressable sounder base. FWSG: Wireless Gateway
B200SR: Addressable sounder base. FWD-200P: intelligent, wireless photo detector.
DNR: InnovairFlex low-flow non-relay duct-detector housing. (Order FWH-200ROR135: LiteSpeed intelligent wireless rate of rise (135°)
FSP-851R, FSP-951R, or NP-100R separately.) heat detector.
DNRW: InnovairFlex low-flow non-relay duct-detector housing, with FWD-200ACCLIMATE: Wireless Acclimate Detector
NEMA-4 rating. Watertight. (Order FSP-851R, FSP-951R, or FWH-200FIX135: intelligent wireless fixed-temperature (135°) heat
NP-100R separately.) detector.
Addressable Modules FW-MM: Intelligent wireless monitor module.
FMM-1: Addressable Monitor Module for one zone of normally-open FW-RM: Intelligent wireless relay module.
dry-contact initiating devices. Mounts in standard 4.0" (10.16 cm.) NBG-12LW: Intelligent wireless pull station.
box. Includes plastic cover plate and end-of-line resistor. Module WAV-RL, WAV-WL,WAV-CRL,WAV-CWL: Intelligent AV bases.
may be configured for either a Style B (Class B) or Style D (Class A)
W-USB: Wireless USB radio/antenna dongle that plugs into the
IDC.
USB port of a PC running SWIFT Tools.
NMM-100: Addressable Monitor Module for one zone of normally- SWIFT Tools: Programming and diagnostic utility for the Wireless
open dry-contact initiating devices. Mounts in standard 4.0" (10.16 Gateway and devices. Available for download from firelite.com.
cm.) box. Includes plastic cover plate and end-of-line resistor. Mod-
NOTE: For more information on Compatible Addressable Devices for
ule may be configured for either a Style B (Class B) or Style D (Class
use with the FireWarden-100X, see the following data sheets (document
A) IDC. numbers): NP-200 Series (DN-60979), NH-200 Series (DN-60980),
FDM-1: Dual Monitor Module. Same as NMM-100 except it provides FSP-851 Series (DN-6935), FSP-951 Series (DN-60977), FST-851
two Style B (Class B) only IDCs. Series (DN-6936), FST-951 Series (DN-60975), FAPT-851 (DN-6937),
NDM-100: Dual Monitor Module. Same as NMM-100 except it pro- N100-ISO (DN-6994), NP-100 series (DN-6995), NH-100/NH-100R (DN-
vides two Style B (Class B) only IDCs. 6997), DNR/InnovairFlex (DN-60424, DN-60429), NP-A100 (DN-6998),
NMM-100/NMM-100P/NDM-100/NZM-100 (DN-6999), NC-100 (DN-
FMM-101: Miniature version of NMM-100. Excludes LED and Style 7000), NC-100R (DN-60383), NMM-100-10 (DN-6990), MM-1/FDM-1/
D option. Connects with wire pigtails. May mount in device backbox. FZM-1/FMM-101 (DN-6720), FCM-1/FRM-1 (DN-6724), NOT-BG12LX
NMM-100P: Miniature version of NMM-100. Excludes LED and Style (DN-7001), NBG-12LX (DN-6726), and FireWarden SLC Manual
D option. Connects with wire pigtails. May mount in device backbox. (52304).
FZM-1: Similar to NMM-100. Addressable Monitor Module for one
DN-60959:C • 7/16/2018 — Page 3 of 4
SPECIFICATIONS

System Capacity Addressable Device Accessories

• Intelligent Signaling Line Circuits................................................1 End-of-Line Resistor Assembly (R-47K and R-3.9K): The
• Addressable device capacity ..................................................198 47k ohm assembly supervises the NMM-100-10, NDM-100, NMM-
100P, and NC-100 module circuits. The 3.9k ohm assembly super-
• Programmable software zones .................................................99
vises the NZM-100-6 module circuit. These resistors are included
• Annunciators.............................................................................16 with each module.
Power Supervision Relay: Supervises the power to 4-wire smoke
Electrical Specifications detectors and notification appliances.
AC Power: Operates in either 120 or 240 VAC, 50/60 Hz, 3.25 A,
auto-sensing- no switch required. Wire size: minimum 14 AWG Wiring Requirements
(2.00 mm2) with 600 V insulation. Nonpower-limited, supervised. While shielded wire is not required, it is recommended that all SLC
wiring be twisted-pair to minimize the effects of electrical interfer-
Battery: Two 12 V 18 AH lead-acid batteries. Battery Charger ence. Refer to the panel manual for wiring details.
Capacity: 7-18 AH (FireWarden-100X cabinet holds maximum of
two 18 AH batteries.)
NFPA Standards
Communication Loop: Supervised and power-limited.
The FireWarden-100X complies with the following NFPA 72 Fire
Notification Appliance Circuits: Terminal Block provides connec- Alarm Systems requirements:
tions for four NACs, Style Y (Class B) or Style Z (Class A). Special
– LOCAL (Automatic, Manual, Waterflow and Sprinkler Supervi-
Application power. Power-limited, supervised circuitry. Maximum
sory).
signaling current per circuit: 2.5 amps special application, 250mA
regulated. End-of-Line Resistor: 4.7k ohm, ½ watt (P/N 71252 UL – AUXILIARY (Automatic, Manual and Waterflow) (requires
listed) for Style Y (Class B) NAC; system capable of 1.9 kΩ - 22 kΩ 4XTM).
ELR range. Refer to the NOTIFIER Device Compatibility Document – REMOTE STATION (Automatic, Manual and Waterflow)
for listed compatible devices. (Where a DACT is not accepted, the alarm, trouble and supervi-
Two Programmable Relays and One Fixed Trouble Relay: Con- sory relays may be connected to UL 864 listed transmitters. For
tact rating: 2.0 A @ 30 VDC (resistive), 0.5 A @ 30 VAC (resistive). reverse polarity signaling of alarm and trouble, 4XTM is
Form-C relays, non-power-limited, non-supervised. required.)
– PROPRIETARY (Automatic, Manual and Waterflow).
Cabinet Specifications – CENTRAL STATION (Automatic, Manual and Waterflow, and
Sprinkler Supervised).
Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x 0.72"
– OT, PSDN (Other Technologies, Packet-switched Data Net-
(1.82 cm.) deep. Backbox: 19.00" (48.26 cm.) high x 16.65" (42.29
work)
cm.) wide x 5.25" (13.34 cm.) deep. Trim Ring (TR-CE/B): 22.00"
(55.88 cm.) high x 19.65" (49.91 cm.) wide. – IBC 2012, IBC 2009, IBC 2006, IBC 2003, IBC 2000 (Seismic).
– CBC 2007 (Seismic)
Shipping Specifications
Weight: 26.9 lbs. (12.20 kg.) Dimensions: 20.00” (50.80 cm.) high Agency Listings and Approvals
x 22.5” (57.15 cm.) wide x 8.5” (21.59 cm.) deep. The listings and approvals below apply to the basic FireWarden-
100X control panel. In some cases, certain modules may not be
Temperature and Humidity Ranges listed by certain approval agencies, or listing may be in process.
Consult factory for latest listing status.
This system meets NFPA requirements for operation at 0 – 49°C/32
– 120°F and at a relative humidity 93% ± 2% RH (noncondensing) at • UL: S635
32°C ± 2°C (90°F ± 3°F). However, the useful life of the system's • CSFM: 7165-0028:0505
standby batteries and the electronic components may be adversely • FDNY: COA #6268
affected by extreme temperature ranges and humidity. Therefore, it
is recommended that this system and its peripherals be installed in
an environment with a normal room temperature of 15 – 27°C/60 –
80°F.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.

AlarmNet®, NOTIFIER®, FireWarden®, SWIFT®, and System Sensor®

NOTIFIER are registered trademarks of Honeywell International Inc. Microsoft® and
12 Clintonville Road Windows® are registered trademarks of the Microsoft Corporation.
Northford, CT 06472 ©2018 by Honeywell International Inc. All rights reserved. Unauthorized
use of this document is strictly prohibited.
203.484.7161
www.notifier.com Country of Origin: USA