Scribd
Upload
108 views

CC2500 RF Transceiver Module

The CC2500 RF Transceiver Module allows for wireless communication at distances up to 30 meters using radio frequency technology. It can transmit serial data from 9600 to 38400 baud and supports multiple network topologies. Key advantages include low cost, low power consumption, and appropriate range and data transfer rates for industrial and commercial applications.

Uploaded by

Suraj Vinod Nayak
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
108 views

CC2500 RF Transceiver Module

The CC2500 RF Transceiver Module allows for wireless communication at distances up to 30 meters using radio frequency technology. It can transmit serial data from 9600 to 38400 baud and supports multiple network topologies. Key advantages include low cost, low power consumption, and appropriate range and data transfer rates for industrial and commercial applications.

Uploaded by

Suraj Vinod Nayak
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

CC2500 RF Transceiver Module

RF Transceiver is a wireless technology developed as an open global standard to


address the unique needs of low-cost, low-power wireless M2M networks.

The RF Transceiver protocol is designed to communicate data through hostile RF


environments that are common in commercial and industrial applications. RF Transceiver
Support for multiple network topologies such as point-to-point, point-to-multipoint and mesh
networks

Description:
1) Baud Rate: 9600 to 38400. Serial UART Mode
2) Packet Length: Variable or Fixed .
3) 30+ meters range.

4) Multiple channel selection enabling upto 255 different pairs to work in the same area
5) Modes of operation: Config mode and Run mode.
6) Onboard jumper Setting for Config/Run Mode and Packet/Byte Mode.
7) Direct Replacement for wired Serial Cable for and serial communication
8) Working with CC2500 Wireless Transceiver module

Advantages of RF Transceiver

1. Chip-vendor independence
2. Rapid innovation
3. Extremely Low cost
4. Open standards enable markets
5. Easy to deploy
6. Excellent performance in environments with low signal-to-noise ratio
7. Appropriate range of operation (30 - 100 meters)
8. Appropriate and reliable data transfer, bit rate : 250kbps at 2.4 GHz
9. Very low power consumption
10. Secure data transfer
11. RF Transceiver protocol needs less than 64 kb of ROM and 2-32 kb of RAM
12. RF Transceiver can bee implemented with any type of microcontroller
Overview:

CC2500 RF Module is a trans receiver module which provides easy to use RF


communication at 2.4 Ghz. It can be used to transmit and receive data at 9600 baud rates from
any standard CMOS/TTL source. This module is a direct line in replacement for your serial
communication it requires no extra hardware and no extra coding toIt works in Half Duplex
mode i.e. it provides communication in both directions, but only one direction at same time.

Specifications:
Input Voltage - 5Volts DC
Baud Rate - 9600
RS 232 Interface & TTL Interface
Range – Max 30 Mtrs - Line of Sight
Channels - 3 Ch - JP1 & JP2 - Ch 1 On – On

CC2500 RF Module
Channel Setting - If you need To use More than 2 RF transceiver in the same place So
you can set in Different Channels - settings Given Below - JP1 and JP2 is nearby Chip in
BOT Layer PCB.

CHANNELS JP1 JP2


CH1 OFF OFF
CH2 ON OFF
CH3 OFF ON
Flochart of Transmtting serial data from microcontroller:
Flochart of Transmtting serial data from microcontroller:

Applications:
Wireless Sensor Network.
Wireless Device Control.
Wireless Data Transfer.
Wireless Energy Metering
Home Automation

NOTE:
Obstacles are among the biggest problems the range will vary according to the size and type
of Obstacles.

You might also like