Scribd
Upload
34 views

Objectives:: Experiment 7 Open & Closed Loop Systems

This document describes open and closed loop control systems and an experiment to control the position of a DC motor using a closed loop system. Open loop systems do not use feedback to regulate outputs, while closed loop systems use feedback to compare outputs to inputs and correct any errors. The experiment involves connecting a potentiometer to measure the motor's position, interpolating the voltage reading to an angular value, comparing it to a desired position, and using the error signal to control an H-bridge motor driver to move the motor into the correct position. The goal is to build a closed loop control system to precisely position the motor.

Uploaded by

Hennesey Lourice
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
34 views

Objectives:: Experiment 7 Open & Closed Loop Systems

This document describes open and closed loop control systems and an experiment to control the position of a DC motor using a closed loop system. Open loop systems do not use feedback to regulate outputs, while closed loop systems use feedback to compare outputs to inputs and correct any errors. The experiment involves connecting a potentiometer to measure the motor's position, interpolating the voltage reading to an angular value, comparing it to a desired position, and using the error signal to control an H-bridge motor driver to move the motor into the correct position. The goal is to build a closed loop control system to precisely position the motor.

Uploaded by

Hennesey Lourice
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Experiment 7

Open & Closed Loop Systems

Objectives:
1- Understand the difference between open and closed loop systems.
2- Study motor drives (H-Bridge).
3- Control the position of a motor using DAC & Labview.

Introduction:
A control system has an input, a process, and an output. Control systems can be
open-loop or closed-loop.

Open Loop Systems:


An open-loop control system is controlled directly, and only, by an input signal,
without the benefit of feedback. A characteristic of the open-loop system is that it
does not use feedback to determine if its output has achieved the desired goal of the
input. This means that the system does not observe the output of the processes that
it is controlling. Consequently, a true open-loop system cannot correct any errors
that it could make. It also may not compensate for disturbances in the system.

Examples of open loop systems:

1- Washing machines (the activation of the washing machine is determined simply


by a person starting it, not the dryness of the clothes).
2- Cell phones (the cell phone is turned on and off by the person using it, not
depending on whether or not it is actually receiving a call).
3- A system consisting of an amplifier and a motor. The amplifier receives a low-
level input signal and amplifies it enough to drive the motor to perform the
desired job.

Figure (1): Example of an open loop system


Closed Loop Systems:
A closed-loop system uses feedback to control states or outputs of a dynamical
system. A closed loop system compensates for disturbances by measuring the output
response, feeding that measurement back through a feedback path, and comparing that
response to the input at the summing junction. If there is any difference between the two
responses, the system drives the plant, via the actuating signal, to make a correction. If
there is no difference, the system does not drive the plant, since the plant's response is
already the desired response. This means that a closed-loop system is able to regulate
itself in the presence of disturbance or variations in its own characteristics.

Examples of closed loop system:

1- System that controls the position and speed of a motor.


2- Systems that control the temperature of a room.
3- Systems that control the level of water in a tank.

Figure (2): Example of a closed loop system

Motor Drivers:
Motor drivers are essentially power amplifiers; their function is to take a low-current
control signal, and turn it into a proportionally higher-current signal that can drive a
motor. Note here that the control signal is likely on the order of 10 mA, and the
motor may require 100's of mA to make it turn. An example of a motor driver is an
H-Bridge.
An H-bridge is an electronic circuit which enables a voltage to be applied across a
load in either direction. These circuits are often used in robotics and other
applications to allow DC motors to run forwards and backwards. H-bridges are
available as integrated circuits, or can be built from discrete components.
Figure (3): Structure of an H-bridge

An H-bridge is built with four switches (solid-state or mechanical). When the


switches S1 and S4 are closed (and S2 and S3 are open) a positive voltage will be
applied across the motor. By opening S1 and S4 switches and closing S2 and S3
switches, this voltage is reversed, allowing reverse operation of the motor.

Note: the switches S1 and S2 should never be closed at the same time, as this would
cause a short circuit on the input voltage source. The same applies to the switches S3
and S4.

Interpolation method:
A sensor is used to measure physical quantities such as temperature, speed,
position, intensity ....etc. These measurements should be feedback and compared to
the desired (input) value and the compensator will correct the error.

In order to relate these physical quantities to values a compensator can understand


interpolation is used.

Interpolation: is a method of constructing new data points within the range of


known data points.
Interpolation formula:

Lab Work:
The aim of this lab is to control the position of a DC motor by close loop system.

-The shaft of the DC motor is connected to a potentiometer (a sensor).

- The voltage across the variable resistor (0 volt to 5 volt) should be related to the
angle of the DC motor rotating from ( . This is done using interpolation
method.

-Then the measured angle (actual theta) should be compared to a desired value and
find the difference between the actual theta and desired theta (error signal).

-This means that the error signal is the difference between the reference input and
the output. Finally a comparison is done. There are 3 cases:

1- If the error signal is zero. Then the value applied to the H-bridge (which is
connected to the digital output pins of the DAC) is 0 forcing the motor to stop.
2- If the error signal is a positive value (actual value less than desired value) we shall
apply logic 1 on one pin of the DAC and logic 0 on the other pin of the DAC
forcing the motor to rotate in a direction that will correct the error.
3- If the error signal is a negative value (actual value larger than desired value) we
shall apply logic 1 & 0 on the pins of the DAC to force the motor to rotate in
reverse direction and correct the error.
Part (1):

Connect a potentiometer to the analog input pin of the DAC and convert the voltage
values to angle values using interpolation method. Display the converted values on
an indicator on the front panel of the Labview.

Part (2):

Find the error signal between desired theta and the actual measured theta. Use a
control (Knob) to apply the desired theta and an indicator to display the value of the
error signal.

Part (3):

Built a compensator that will drive the DC motor to its' desired position.

Final result:

You might also like