Paper Code- : EC402ES

SRIDEVI WOMEN’S ENGINEERING COLLEGE – GANDIPET, HYDERABAD

B.Tech, II Year II Sem., I Mid-Term Examinations, February-2019
PULSE AND DIGITAL CIRCUITS
Objective Question Paper SET 1
Name: Hall Ticket No.:

Answer All Questions. Time: 20 Min. Marks: 10

I. Choose the correct alternative:

1. The waveform which preserves its form when transmitted through linear network is a / an
[a] Sine Wave [b] Step Signal [c] Impulse signal [d] ramp signal [ ]

2. For a sinusoidal input, the gain of a low pass filter is given by

1 1 1 1
[a] 𝑓 2 [b] 𝑓 2 [c] 𝑓2 2 [d] 𝑓2 2 [ ]
{[1+ ] }1/2 {[1− ] }1/2 {[1+ ] }1/2 {[1− ] }1/2
𝑓2 𝑓2 𝑓 𝑓

3. The Rise time of the output of a low-pass RC circuit is given by

[a] 𝑡𝑟 = 2.2𝑅𝐶 [b] 𝑡𝑟 = 0.35/𝑓2 [c] 𝑡𝑟 = 2.2τ [d] all the above

4. The Output of RC differentiating Circuit is given by

1 1 𝑑𝑣𝑖
[a] 𝑅𝐶 ∫ 𝑖 𝑑𝑡 [b] RC∫ 𝑖 𝑑𝑡 [c] 𝑅𝐶 𝑑𝑡
[d] None of these [ ]

5. In an attenuator, the final voltage is determined by

[a] Capacitors [b] resistors [c] both a and b [d] none of these [ ]

6. Clipping Circuits are used to

[a] attenuate the signals [b] amplify the signals [c] remove the part of the signal [d] none [ ]

7. Regenerative Comparators employ

[a] negative feedback [b] positive feedback [c] both a and b [d] none of the above [ ]

8. In Clamping Circuits, The Capacitors are

[a] unavoidable [b] desirable [c]essential [d] none of the above [ ]

9. A Circuit which clamps the negative peak of a signal to zero is called

[a] Positive Clamping Circuit [b] Negative Clamping Circuit [c] Positive Peak Clamping Circuit
[d] negative peak clamping circuit [ ]

10. The Clamping Circuit Theorem states that

𝐴𝑓 𝑅𝑓 𝐴𝑓 𝑅𝑓 𝐴𝑓 𝐴𝑟
[a] = [b] = [c] = [d] Af Rf= 𝐴𝑟𝑅 [ ]
𝐴𝑟 𝑅 𝐴𝑟 𝑅𝑟 𝑅𝑓 𝑅
 Paper Code- : EC402ES

II. Fill in the Blanks:

11. The Emitter Coupled Clippers are ---------------------------------------

12. In a diode non linearity occurs when it goes from -------------------------- to -------------------------

13. The blocking oscillator comparator generates ------------------------

14. In --------------------------- clamping, a reference voltage source is connected in series with the diode.

15. -----------------------is the process of cutting and removing a part of waveform

16. A high pass circuit act as a ------------------------------if the time constant of the circuit is small

17. A network which can be mathematically described by linear coefficient differential equation is called as ----

---------------------------------

18. At very high frequency the capacitor acts as ------------------------------------

19. The Rise time Tr is given by----------------------------------

20. Attenuators are used to ------------------------------ reduce the amplitude of the input signal
 Paper Code- : EC402ES
SRIDEVI WOMEN’S ENGINEERING COLLEGE – GANDIPET, HYDERABAD
B.Tech, II Year II Sem., I Mid-Term Examinations, February-2019
PULSE AND DIGITAL CIRCUITS
Objective Question Paper SET 2
Name: Hall Ticket No.:

Answer All Questions. Time: 20 Min. Marks: 10

I. Choose the correct alternative:

1. Clipping Circuits are used to
[a] attenuate the signals [b] amplify the signals [c] remove the part of the signal [d] none [ ]

2. Regenerative Comparators employ

[a] negative feedback [b] positive feedback [c] both a and b [d] none of the above [ ]

3. In Clamping Circuits, The Capacitors are

[a] unavoidable [b] desirable [c]essential [d] none of the above [ ]

4. A Circuit which clamps the negative peak of a signal to zero is called

[a] Positive Clamping Circuit [b] Negative Clamping Circuit [c] Positive Peak Clamping Circuit
[d] negative peak clamping circuit [ ]

5. The Clamping Circuit Theorem states that

𝐴𝑓 𝑅𝑓 𝐴𝑓 𝑅𝑓 𝐴𝑓 𝐴𝑟
[a] 𝐴 = [b] = 𝑅𝑟 [c] 𝑅 = [d] Af Rf= 𝐴𝑟𝑅 [ ]
𝑟 𝑅 𝐴𝑟 𝑓 𝑅

6. The waveform which preserves its form when transmitted through linear network is a / an
[a] Sine Wave [b] Step Signal [c] Impulse signal [d] ramp signal [ ]

7. For a sinusoidal input, the gain of a low pass filter is given by

1 1 1 1
[a] 𝑓 2 [b] 𝑓 2 [c] 𝑓2 2 [d] 𝑓2 2 [ ]
{[1+ ] }1/2 {[1− ] }1/2 {[1+ ] }1/2 {[1− ] }1/2
𝑓2 𝑓2 𝑓 𝑓

8. The Rise time of the output of a low-pass RC circuit is given by

[a] 𝑡𝑟 = 2.2𝑅𝐶 [b] 𝑡𝑟 = 0.35/𝑓2 [c] 𝑡𝑟 = 2.2τ [d] all the above

9. The Output of RC differentiating Circuit is given by

1 1 𝑑𝑣𝑖
[a]
𝑅𝐶
∫ 𝑖 𝑑𝑡 [b] RC∫ 𝑖 𝑑𝑡 [c]
𝑅𝐶 𝑑𝑡
[d] None of these [ ]

10. In an attenuator, the final voltage is determined by

[a] Capacitors [b] resistors [c] both a and b [d] none of these [ ]
 Paper Code- : EC402ES

II. Fill in the Blanks:

1. A high pass circuit act as a ------------------------------if the time constant of the circuit is small

2. A network which can be mathematically described by linear coefficient differential equation is called as ----

---------------------------------

3. At very high frequency the capacitor acts as ------------------------------------

4. The Rise time Tr is given by----------------------------------

5. Attenuators are used to ------------------------------ reduce the amplitude of the input signal

6. The Emitter Coupled Clippers are ---------------------------------------

7. In a diode non linearity occurs when it goes from -------------------------- to -------------------------

8. The blocking oscillator comparator generates ------------------------

9. In --------------------------- clamping, a reference voltage source is connected in series with the diode.

10. -----------------------is the process of cutting and removing a part of waveform

 Paper Code- : EC402ES
SRIDEVI WOMEN’S ENGINEERING COLLEGE – GANDIPET, HYDERABAD
B.Tech, II Year II Sem., I Mid-Term Examinations, February-2019
PULSE AND DIGITAL CIRCUITS
Objective Question Paper SET 3
Name: Hall Ticket No.:

Answer All Questions. Time: 20 Min. Marks: 10

I Choose the correct alternative:

1. The waveform which preserves its form when transmitted through linear network is a / an
[a] Sine Wave [b] Step Signal [c] Impulse signal [d] ramp signal [ ]

2. The Rise time of the output of a low-pass RC circuit is given by

[a] 𝑡𝑟 = 2.2𝑅𝐶 [b] 𝑡𝑟 = 0.35/𝑓2 [c] 𝑡𝑟 = 2.2τ [d] all the above

3. In an attenuator, the final voltage is determined by

[a] Capacitors [b] resistors [c] both a and b [d] none of these [ ]

4. Regenerative Comparators employ

[a] negative feedback [b] positive feedback [c] both a and b [d] none of the above [ ]

5. A Circuit which clamps the negative peak of a signal to zero is called

[a] Positive Clamping Circuit [b] Negative Clamping Circuit [c] Positive Peak Clamping Circuit
[d] negative peak clamping circuit [ ]

6. For a sinusoidal input, the gain of a low pass filter is given by

1 1 1 1
[a] 𝑓 2 [b] 𝑓 2 [c] 𝑓2 2 [d] 𝑓2 2 [ ]
{[1+ ] }1/2 {[1− ] }1/2 {[1+ ] }1/2 {[1− ] }1/2
𝑓2 𝑓2 𝑓 𝑓

7. The Output of RC differentiating Circuit is given by

1 1 𝑑𝑣𝑖
[a] 𝑅𝐶 ∫ 𝑖 𝑑𝑡 [b] RC∫ 𝑖 𝑑𝑡 [c] 𝑅𝐶 𝑑𝑡
[d] None of these [ ]

8. Clipping Circuits are used to

[a] attenuate the signals [b] amplify the signals [c] remove the part of the signal [d] none [ ]

9. In Clamping Circuits, The Capacitors are

[a] unavoidable [b] desirable [c]essential [d] none of the above [ ]

10. The Clamping Circuit Theorem states that

𝐴𝑓 𝑅𝑓 𝐴𝑓 𝑅𝑓 𝐴𝑓 𝐴𝑟
[a] = [b] = [c] = [d] Af Rf= 𝐴𝑟𝑅 [ ]
𝐴𝑟 𝑅 𝐴𝑟 𝑅𝑟 𝑅𝑓 𝑅
 Paper Code- : EC402ES

II. Fill in the Blanks:

11. The Emitter Coupled Clippers are ---------------------------------------

12. The blocking oscillator comparator generates ------------------------

13. -----------------------is the process of cutting and removing a part of waveform

14. A network which can be mathematically described by linear coefficient differential equation is called as ----

---------------------------------

15. The Rise time Tr is given by----------------------------------

16. In a diode non linearity occurs when it goes from -------------------------- to -------------------------

17. In --------------------------- clamping, a reference voltage source is connected in series with the diode.

18. A high pass circuit act as a ------------------------------if the time constant of the circuit is small

19. At very high frequency the capacitor acts as ------------------------------------

20. Attenuators are used to ------------------------------ reduce the amplitude of the input signal
 Paper Code- : EC402ES
SRIDEVI WOMEN’S ENGINEERING COLLEGE – GANDIPET, HYDERABAD
B.Tech, II Year II Sem., I Mid-Term Examinations, February-2019
PULSE AND DIGITAL CIRCUITS
Objective Question Paper SET 4
Name: Hall Ticket No.:

Answer All Questions. Time: 20 Min. Marks: 10

I Choose the correct alternative:

1. For a sinusoidal input, the gain of a low pass filter is given by
1 1 1 1
[a] 𝑓 [b] 𝑓 [c] 𝑓2 [d] 𝑓2 [ ]
{[1+ ]2 }1/2 {[1− ]2 }1/2 {[1+ ]2 }1/2 {[1− ]2 }1/2
𝑓2 𝑓2 𝑓 𝑓

2. The Output of RC differentiating Circuit is given by

1 1 𝑑𝑣𝑖
[a] 𝑅𝐶 ∫ 𝑖 𝑑𝑡 [b] RC∫ 𝑖 𝑑𝑡 [c] 𝑅𝐶 [d] None of these [ ]
𝑑𝑡

3. Clipping Circuits are used to

[a] attenuate the signals [b] amplify the signals [c] remove the part of the signal [d] none [ ]

4. In Clamping Circuits, The Capacitors are

[a] unavoidable [b] desirable [c]essential [d] none of the above [ ]

5. The Clamping Circuit Theorem states that

𝐴𝑓 𝑅𝑓 𝐴𝑓 𝑅𝑓 𝐴𝑓 𝐴𝑟
[a] 𝐴 = 𝑅
[b] 𝐴𝑟
= 𝑅𝑟 [c] 𝑅 = 𝑅
[d] Af Rf= 𝐴𝑟𝑅 [ ]
𝑟 𝑓

6. The waveform which preserves its form when transmitted through linear network is a / an

[a] Sine Wave [b] Step Signal [c] Impulse signal [d] ramp signal [ ]

7. The Rise time of the output of a low-pass RC circuit is given by

[a] 𝑡𝑟 = 2.2𝑅𝐶 [b] 𝑡𝑟 = 0.35/𝑓2 [c] 𝑡𝑟 = 2.2τ [d] all the above

8. In an attenuator, the final voltage is determined by

[a] Capacitors [b] resistors [c] both a and b [d] none of these [ ]

9. Regenerative Comparators employ

[a] negative feedback [b] positive feedback [c] both a and b [d] none of the above [ ]

10. A Circuit which clamps the negative peak of a signal to zero is called

[a] Positive Clamping Circuit [b] Negative Clamping Circuit [c] Positive Peak Clamping Circuit

[d] negative peak clamping circuit [ ]

 Paper Code- : EC402ES
II. Fill in the Blanks:
1. The blocking oscillator comparator generates ------------------------

2. A network which can be mathematically described by linear coefficient differential equation is called as ----

---------------------------------

3. In a diode non linearity occurs when it goes from -------------------------- to -------------------------

4. A high pass circuit act as a ------------------------------if the time constant of the circuit is small

5. Attenuators are used to ------------------------------ reduce the amplitude of the input signal

6. The Emitter Coupled Clippers are ---------------------------------------

7. -----------------------is the process of cutting and removing a part of waveform

8. The Rise time Tr is given by----------------------------------

9. In --------------------------- clamping, a reference voltage source is connected in series with the diode.

10. At very high frequency the capacitor acts as ------------------------------------