Scribd
Upload
1K views

Material Science/Failure Multiple Choice Questions

The document contains a set of 21 multiple choice questions about material science failures. The questions cover topics such as: the factors that control failure due to excessive deformation; types of fractures like cleavage and brittle; how properties like fracture toughness and ductile-to-brittle transition temperature are affected by factors like temperature, stress, and impurities; fatigue strength testing parameters; creep mechanisms and stages; and how fracture strength relates to crack depth in brittle materials. Answers to all 21 questions are provided at the end.

Uploaded by

Tohid Ansari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Material Science/Failure Multiple Choice Questions

The document contains a set of 21 multiple choice questions about material science failures. The questions cover topics such as: the factors that control failure due to excessive deformation; types of fractures like cleavage and brittle; how properties like fracture toughness and ductile-to-brittle transition temperature are affected by factors like temperature, stress, and impurities; fatigue strength testing parameters; creep mechanisms and stages; and how fracture strength relates to crack depth in brittle materials. Answers to all 21 questions are provided at the end.

Uploaded by

Tohid Ansari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Material Science/Failure Multiple Choice Questions

Multiple Choice Questions:

1. Failure due to excessive deformation is controlled by ______________.


(a) Material properties (b) Design & Dimensions (c) Both (d) None
2. Failure due to excessive deformation is controlled by ______________.
(a) Yield strength (b) Tensile strength (c) Young’s modulus (d) All
3. Time dependent yield is known as
(a) Fracture (b) Fatigue (c) Buckling (d) Creep
4. Cleavage fracture appears
(a) Bright (b) Dull (c) Difficult to identify (d) None
5. Usually materials with following crystal structure fail in ductile mode
(a) FCC (b) BCC (c) HCP (d) None
6. Brittle fracture is more dangerous than ductile fracture because _______________.
(a) No warning sign
(b) Crack propagates at very high speeds
(c) No need for extra stress during crack propagation
(d) All
7. Fracture voids usually form at
(a) Inclusions (b) Second phase particles (c) Grain boundary triple points (d) All
8. Fracture stress (σf) is proportional to
(a) crack length (b) 1/crack length (c) (crack length)1/2 (d) (crack length)-1/2
9. Fracture toughness is measured in terms of
(a) Strain energy release rate (b) Stress concentration factor (c) Both (d) None
10. In fracture mode-II, fracture surfaces
(a) shear parallel to edge of crack
(b) shear perpendicular to edge of crack
(c) displace normal to each other
(d) None
11. Fracture toughness, KIC, decreases with
(a) increasing temperature
(b) increasing strain rate
(c) increase in yield strength
(d) increase in grain size
12. DBTT for ceramics is in the range of _________ X Tm.
(a) 0.1-0.2 (b) 0.2-0.3 (c) 0.3-0.5 (d) 0.5-0.7
13. Following impurity decreases DBTT for steels
(a) Mn (b) P (c) Si (d) Mo
14. Fatigue strength for non-ferrous materials in defined at _______ stress cycles.
(a) 103 (b) 105 (c) 107 (d) 109
15. The following equation defines S-N curve
(a) Paris equation (b) Basquin equation (c) Andrede equation (d) Garofalo equation
16. Creep rate in ternary stage __________.
(a) Decreases (b) Constant (c) Increases (d) None
17. Ternary stage creep is associated with ____________.
(a) Strain hardening (b) Recovery (c) Necking (d) None
18. Total strain range in a creep test
(a) <1% (b) around 10% (c) around 50% (d) > >50%
19. Creep mechanism that is operational at stresses 10-2 >σ/G >10-4 _____________.
(a) Dislocation creep (b) Dislocation glide (c) Diffusion creep (d) GB sliding
20. Most often machine components fail by
(a) Buckling (b) Creep (c) Fatigue (d) All

Satish V. Kailas/IISc, Bangalore M8/V1/June 04/1


Material Science/Failure Multiple Choice Questions

21. If the surface crack causing fracture in a brittle material is made twice as deep, the fracture strength
will
(a) decrease by a factor of √2
(b) decrease by a factor of 2
(c) decrease by a factor of 22
(d) No change

Satish V. Kailas/IISc, Bangalore M8/V1/June 04/2


Material Science/Failure Multiple Choice Questions

Answers:

1. c
2. c
3. d
4. a
5. a
6. d
7. d
8. d
9. c
10. b
11. b
12. a
13. a
14. c
15. b
16. c
17. c
18. a
19. a
20. c
21. a

Satish V. Kailas/IISc, Bangalore M8/V1/June 04/3

You might also like