0% found this document useful (0 votes)
66 views

Data Sheet

This document provides specifications for MCC's MB05S through MB10S series of single phase bridge rectifier diodes. It includes maximum ratings for peak reverse voltage, RMS voltage, and blocking voltage. Features are listed as surface mount, glass passivated construction, and moisture resistant epoxy case. Electrical characteristics include average forward current, peak forward surge current, forward voltage, reverse leakage current, and junction capacitance. Curves show forward and reverse characteristics and forward current derating with temperature.
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
66 views

Data Sheet

This document provides specifications for MCC's MB05S through MB10S series of single phase bridge rectifier diodes. It includes maximum ratings for peak reverse voltage, RMS voltage, and blocking voltage. Features are listed as surface mount, glass passivated construction, and moisture resistant epoxy case. Electrical characteristics include average forward current, peak forward surge current, forward voltage, reverse leakage current, and junction capacitance. Curves show forward and reverse characteristics and forward current derating with temperature.
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

MCC 






MB05S

 THRU
  !"#
$
%    !"# MB10S

Features 0.5Amp Single Phase


• Surface Mount Package Glass Passivated
• Glass Passivated Diode Construction
• Moisture Resistant Epoxy Case Bridge Rectifier
• High Surge Current Capability
50 to 1000 Volts

Maximum Ratings MBS -1


• Operating Temperature: -55°C to +150°C
• Storage Temperature: -55°C to +150°C
∼ -
MCC Device Maximum Maximum Maximum B D
E
Catalog Marking Rccurrent RMS DC
Number Peak Reverse Voltage Blocking ∼ +
Voltage Voltage
MB05S MB05S 50V 35V 50V C F
MB1S MB1S 100V 70V 100V A
MB2S MB2S 200V 140V 200V
MB4S MB4S 400V 280V 400V Notch in case
MB6S MB6S 600V 420V 600V K
MB8S MB8S 800V 560V 800V M
MB10S MB10S 1000V 700V 1000V J
G N
H
Electrical Characteristics @ 25°C Unless Otherwise Specified L
Average Forward IF(AV) 0.5A Note1 TA = 30°C
Current 0.8A Note2 TA = 30°C
Peak Forward Surge IFSM 30A 8.3ms, half sine 
Current     

 
Maximum       
Instantaneous VF 1.0V IFM = 0.5A; .252 .272 6.40 6.91
    
Forward Voltage TA = 25°C     
    
Maximum DC  .017 .029 0.45 0.75
Reverse Current At IR 5 µA TA = 25°C  .090 .106 2.30 2.70
 .004 .008 0.10 0.20
Rated DC Blocking
.021 .023 0.53 0.58
Voltage  .055 .065 1.40 1.65
 ----- .200 ----- 5.08
Typical Junction CJ 25pF Measured at     
Capacitance 1.0MHz, VR=4.0V M .040 .050 1.02 1.27
 .008 .014 0.15 0.35
Note1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
Note2. On alum: substrate P.C.B with an rea of 0.8 x 0.8 x 0.25”
( 20 x 20 x 6.4mm ) mounte on 0.05 x 0.05 “( 13 x 13 mm )
solder pad.
*Pulse Test: Pulse Width 300µsec, Duty Cycle 1%

www.mccsemi.com
MB05S thru MB10S
MCC
Figure 1 Figure 2
Typical Forward Characteristics Typical Reverse Characteristics
20 100
60
10
40
6
20
4
10
2 6
25°C
Amps 1 4

.6 2

.4 µAmps 1
.6
.2
.4
.1
.2
.06 TA=25°C
.1
.04
.06
.04
.02

.01 .02
.4 .6 .8 1.0 1.2 1.4
.01
Volts 20 40 60 80 100 120 140
Instantaneous Forward Current - Amperesversus Volts
Instantaneous Forward Voltage - Volts
Instantaneous Reverse Leakage Current - MicroAmperesversus
Percent Of Rated Peak Reverse Voltage - Volts
Figure 3
Forward Derating Curve Figure 4
1.2 Peak Forward Surge Current
60
1.0
50

.8 40

30
.6 Amps
Amps 20

.4 10
5
0
.2 1 2 4 6 8 10 20 40 60 80 100
Single Phase, Half Wave
60Hz Resistive or Inductive Load Cycles
0
0 40 50 75 100 125 150 175 Peak Forward Surge Current - Amperesversus
Number Of Cycles At 60Hz - Cycles
°C

Average Forward Rectified Current - Amperesversus


Ambient Temperature - °C

www.mccsemi.com

You might also like