Scribd
Upload
42 views

The Laboratory of Mining Design and Planning Is To Apply Mining Software

The laboratory of mining design and planning contains various software used to model mining operations and deposits. This includes Minex for modeling stratified deposits, Surpac for mine planning and optimization, Visual ModFlow for groundwater modeling, and MapInfo Professional for GIS functions. The laboratory tests and applies these software to problems in Estonian mining, such as modeling the oil shale deposit.

Uploaded by

Ayşe Batur
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
42 views

The Laboratory of Mining Design and Planning Is To Apply Mining Software

The laboratory of mining design and planning contains various software used to model mining operations and deposits. This includes Minex for modeling stratified deposits, Surpac for mine planning and optimization, Visual ModFlow for groundwater modeling, and MapInfo Professional for GIS functions. The laboratory tests and applies these software to problems in Estonian mining, such as modeling the oil shale deposit.

Uploaded by

Ayşe Batur
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Laboratory of mining design and planning

The purpose of the laboratory of mining design and planning is to apply mining software
systems, test and develop them in scientific and teaching process. The laboratory consists of
software, databases, methods, hardware with necessary equipment (scanners, printers,
plotters, savers, presenters, computer servers), see the website http://mi.ttu.ee/mgislabor

The most used mining modelling software in the world have been set up in the laboratory:

1. Gemcom Minex – modelling stratified deposits


2. Gemcom Surpac – modelling mining processing and work procedures
3. Visual ModFlow; AquaChem- groundwater flow and quality modelling
4. MapInfo Professional, Discovery, MapBasic - GIS
5. Vertical Mapper- spatial modelling
6. Encom Discover- spatial modelling for mining environment
7. AutoCAD Civil 3D- planning
8. FLAC – modelling of rock mechanics, dynamics and properties
9. PLAXIS – geotechnical spatial modelling
10. Mining specific software – parameters of pillars, productivity, mining equipment co-
operation and fleet calculations, (Caterpillar and Mining Department of TUT)
11. Ashtech GPS data management and analysing
12. GeoLab

Laboratory of mining design and planning


Minex software is used for modelling and design of stratified deposits.
Geological modelling and design for lignite, phosphorite, zinc, bouxite, iron ore and platinum
deposits. Is mainly used for Estonian oil shale deposit planning.
With Minex software it is possible to perform:
Geological modelling taking into account breaks and water regime. To optimize mining with
longwall, reconstruct ramps, overburden coefficient, economical ratio, to calculate volumes.
Shortwall mining with blasting scheme, ramps, roads, heap, redirect pollution.

Figure 1Statistics and histogram about seam D; Clockwise and anticlockwise ramp in mining
with bench
Figure 2 Cross-section of layers with drillholes, geophysics and grid net

Minex homepage http://www.surpac.com/


Software Surpac Vision
With Surpac Vision software it is possible to design and optimize: surfaces mines,
underground mines, tunnels, design drillholes and blasting, model blocks, to make geodetic
data request etc.

Figure 3 Granite underground mine project

Figure 4 Analysis of mining conditions

Surpac Vision homepage and instructions http://www.surpac.com/


Software Visual ModFlow Professional
Software is for constructing three-dimensional groundwater flow and contaminant transport
modeling. With the ability to simulate groundwater and surface water interactions, and the
added capability of calculating changes to groundwater chemistry, groundwater professionals
now have a complete set of tools necessary for addressing water quality, groundwater supply,
and source water protection initiatives. Modeling results help to make decisions about mining
technology and mining operations.
Visual MODFLOW has the tools necessary to:

Graphically assign model grids, properties and boundaries


Visualize model input parameters (2D or 3D views)
Run the flow, pathline, and transport simulations
Automatically (WinPEST) or manually calibrate the model
Display and interpret the modeling results in full 3D
Produce professional reports

Model input parameters and results allow to visualize in two-dimensional cross-sections and
schema and three-dimensional to visualize results. Using dynamic model it is possible to
create new conditions adding new data and valuate water level, groundwater flow directions,
volumes of pumping water in underground mines and surface mines using time.
Cross-sections based on generated model
Creating cross-sections it is possible to visualize in passant water level location in geological
layers.

Figure 5 Cross-section and its location


Balance of the incoming and outgoing water
Model gives the results of incoming and outgoing water volumes at certain moment of time in
certain water level. Results can be viewed in graphs and as data tables (Figure 2).

Figure 6 Incoming and outgoing water volumes


Water flow directions
Simulisation results reveal directions of the water which is shown in Figure 3.

Figure 7 Water flow direction at the moment of 50 days.


Homepage http://www.modflow.com/
Software AquaChem
AquaChem is software for water analysis. AquaChem enables to analyse water chemical
contents and physical parameters, wide analysis, calculate, model, create graphics.

Figure 8 Map of water chemical contents

Figure 9 Water analysis illustration

AquaChem homepage
http://www.waterloohydrogeologic.com/software/aquachem/aquachem_ov.htm

AquaChem users instructions siit


Software MapInfo Professional
MapIfo Professional is software based on GIS. It allows to manage GIS data, model and
manipulate.
MapInfo Professional allows to:
Look map data and geographic coordinates analysis
Carry out data to map
create maps and plot
create and refresh map database
Functionality:
Data visualisation: 3 different views: tables, map, graphs. Monitoring data in scale, create new
map objects, to associate the map objects with the data in tables, thematic maps, 3D thematic
maps, cartographic legend, to combine objects.
Spatial analysis: do SQL-queries and saving, spatial queries and buffers.

Figure 10 Plan created with coordinates

Figure 11 Buffering mining influences

MapInfo Vertical Mapper


software which increases MapInfo analysing capabilities including more difficult functions
based on statistic and raster-grid models. It allows to analyse and visualize height models, to
create thematic maps revealing trends, to interpolate.
Figure 12 Pollution model. This model is illustrative and does not own real values.
AutoCAD

AutoCAD is software based on vector graphic. It is used in creating technological schemes,


cross-sections and plans. With AutoCAD it is possible to create 2D and 3D spatial mechanical
drawings. Suitable for creating drift, cross-sections schemes, supports in geological crush
zones, anchor support schemes, ventilation schemes etc.

Figure 13 Bench properties

Figure 14 Mining with backfilling

Figure 15 Opencast mining

Figure 16 Breaking with hydraulic hammer


Figure 17 High selective surface oil shale mining technology modelled with AutoCad
AutoCAD homepage http://www.autodesk.com/
Plaxis
Plaxis is geotechnical modelling software. It allows to analyse deformations, stability, ground
water flow, create quickly elements, nonlinear and time devolving models taking into account
pore pressure in unisotrophic soils.

Figure 18 Situation before and after deformation

Figure 19 Pore pressure

Plaxis homepage http://www.plaxis.com/


WipFrag
Granulometry Analysis Software. It supplements screen analysis, helps to evaluate loose
which cannot be screened.

Figure 20 Work in 3 phase

Figure 21 Explanation of the graph


WipFrag homepage http://www.wipware.com/wipfrag.php
FLAC

Flac is used for calculating stability, deformations, pressure, crush and to visualize in plastic,
elastic and rheologic environment. In addition it can be used for crack calculations using
thermal and water flow data.
The output is 2D and 3D models.

Joint system for the models

Cavern model in Maardu granite deposit


Caterpillar and Mining Department of TUT Mining specific software – parameters of pillars,
productivity, mining equipment co-operation and fleet calculations,

Figure 24 Transport cost analises and fleet selection in Caterpillar FPA


Software laboratory is continuously testing and analisyng available software, applying it to
local problems and updating licences
Some of softwares being tested are:
1. Itasca Software

2. SoilVision Office 2009

3. ArcGIS 9.2

4. Plaxis 3D Foundation

5. Carlson Software 2009 For AutoCAD with built in ICAD

6. TranSim VS

You might also like