Scribd
Upload
89 views

305-261/262 Measurement Laboratory Experiment IV Time Constant

This document describes an experiment to determine the time constants of various temperature sensors. Students will use LabVIEW to record the voltage output of a thermocouple and resistance temperature detector (RTD) as they are immersed in hot water. The recorded data will be analyzed in Excel to determine the time it takes for each sensor's output to reach 63.2% of its final value, which is defined as the time constant. Students will repeat this process for a shielded thermocouple, exposed thermocouple, and RTD to calculate and compare their individual time constants.

Uploaded by

Mohammad Kh
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
89 views

305-261/262 Measurement Laboratory Experiment IV Time Constant

This document describes an experiment to determine the time constants of various temperature sensors. Students will use LabVIEW to record the voltage output of a thermocouple and resistance temperature detector (RTD) as they are immersed in hot water. The recorded data will be analyzed in Excel to determine the time it takes for each sensor's output to reach 63.2% of its final value, which is defined as the time constant. Students will repeat this process for a shielded thermocouple, exposed thermocouple, and RTD to calculate and compare their individual time constants.

Uploaded by

Mohammad Kh
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

305-261/262 Measurement Laboratory

Experiment IV
Time Constant
Introduction: Time response of first-order transducers
When a transducer is used to measure some physical quantity that changes with time,
the transducer produces an output signal, which represents the measured quantity.
However there will always be some delay between the occurrence of an event to be
measured and the transducer signal that represents it. No matter what kind of transducer
is used, the value of the output signal at a time t will represent the value of the measured
quantity at some earlier instant t  t 0 .
The next illustration shows how a thermocouple voltage changes after being
immersed in hot water. The sudden immersion of the thermocouple into hot water
approximates a step change of temperature. The thermocouple does not reach its final
steady-state output level until some time later. The basic reason for this delay is that it
takes time for the measuring junction to reach the temperature of the surrounding water.

The time it takes for thermocouple’s voltage to reach 63.2% of its final value is called
time constant. It usually ranges from 0.15sec. to 3.90sec. Clearly these thermocouples
cannot be used for applications where temperature changes occur over time interval of
fractions of second.

Temperature transducers are described as first-order linear systems on the assumption


that the rate of change of the temperature T of the measuring transducer is proportional to
the difference between Ti and the final value T f according to the relation:
dT
 k (T f  Ti )
dt
Where k is the proportionality constant. It turns out that the proportionality constant is the
inverse of the time-constant . Thus the equation can be written as:
dT 1
 (Tf  T )
dt 
To find the way in which temperature T of the measuring transducer changes, the solution
of the above equation is obtained knowing that at t = 0 the initial temperature of the
measuring junction is Ti.
T  Ti + (Tf - Ti )(1- e -t / )
This equation is the algebraic expression for the measuring-junction temperature curve of
the above diagram. The equation says that, at any instant, T equals the final temperature
T f less a term that represents the difference between T f and T at that instant.

Objective of the present investigation


1. To build a simple VI instrument able to capture an unknown signal.
2. To determine the approximate time-constants of two thermocouples.
3. To determine the approximate time-constant of a resistance thermometer (RTD).

Equipment provided

 One thermo flask filled with hot water.


 One type E thermocouple shielded.
 One type E thermocouple exposed.
 One Resistance thermometer (RTD).
 One signal conditioner 3B37 for type E thermocouple.
 One signal conditioner 3B14 for RTD sensor.
 One connector (purple) for type E thermocouples.
 One connector (white) for RTD sensors.
 A workstation with LabVIEW.

Procedure (read the instructions before starting)


Start LabVIEW and build a VI instrument as indicated in the diagram included with
these instructions. This simple VI allows you to capture the signal and save it in a data
file, however a few setting must be entered before starting the program. You must enter:
1. The channel where the signal is routed. When you test the Thermocouples
(purple connector) enter channel 2. When you test the RTD (white connector)
enter channel 6.
2. The number of samples to acquire: set 2000.
3. The sampling rate: set 100.
4. Right click the Waveform Graph of your VI to ensure that the X and Y-axes are
in autoscale (checkmark). You can always edit the X and Y scales.
5. Start with the shielded thermocouple (ask the technician) and select the
corresponding channel on your VI.
6. Open the flask of the hot water.
7. One member of the group will dip the thermocouple in the flask (slowly!!!) while
the other partner will start the program.
8. Start the program (RUN) Before dipping the sensor in the water. Since the
sampling rate is 100, the sampling interval is t = 1/100 = 0.01 sec which
multiplied by the number of samples (2000) gives the total sampling time of
20 sec.
9. After the sampling time (20 sec), the computer will prompt you to save the data.
Save in the F: drive as Shielded1.
10. Repeat the experiment if you are not satisfied with the result of the output.
11. Edit the axes of the front panel if necessary.
12. Repeat steps 2 to 10 substituting the shielded thermocouple with the exposed
thermocouple. Save the file as Exposed1.
13. Repeat steps 2 to 10 with the same thermocouple (exposed) but changing the
number of samples to 1000 and the sampling rate to 200. Save the file as
Exposed2.
14. Repeat steps 2 to 10 with the RTD setting the channel to 6, the number of sample
to 2000 and the sampling frequency 100. Save the data as RTD1.
15. Calculate the sampling interval t that you used for each of the 4 tests and write
them on the Datasheet. On a separate paper report all your calculations.

Now you will plot the data you obtained.

1. Start Excel and open Shielded1>> Finish. Excel will display your files in a
column vector (column A).
2. Block column A and go to INSERT>>COLUMN so you can build another
column vector (time) on the left with respect to which you will plot the data.
Now the data is in column B.
3. The Write 0 in the first cell of column A (time “zero”). Time must increase at
intervals equal to the sampling time t.
4. In the second cell write the formula: “ =A1+t” where t is the sampling time
(in seconds) you calculated for this set of data.
5. Check this cell and click COPY. You want to paste this formula in a number of
cells corresponding to the number of samples. Block the next cell in the first
column and drag it down along the column until you reach the end of the data in
the second column.
6. Click PASTE. Now you have obtained two column vectors that can be plotted
against each other (Data point on vertical axis, Time on horizontal axis).

Now you can follow the rest of the instructions if you did not use Excel before.
7. Block Column A and B.
8. On the taskbar click CHART WIZARD>>XY SCATTER and choose the
smoothed line without markers.
9. Click Next>>Next to write the title of the graph and to label the axis with the
appropriate units. Click finish.
10. Right click on the axis to change the scale.
11. Change the scale of the horizontal axis to allow you to measure with sufficient
precision both the voltage change and the time interval.
12. When you are satisfied with the look of your graph print it. Print only the
graph, not the data file.
13. Measure directly on the graph the voltage change from the instant you dipped
the transducer in the hot water to the final voltage. Write the voltage change on
the datasheet.
14. Calculate 63.2% of this voltage and mark this value on the graph.
15. Measure the time interval from the instant you dipped the transducer in the
water to the instant where the voltage reaches 63.2% of the final value. This is
the time constant . Write it on your datasheet.
16. Repeat these steps with the other files.
17. Hand in the datasheet, the 4 graphs with your sketches and all your calculations.

You might also like