Scribd
Upload
73 views2 pages

Base Plate Detail - D

The document provides design details for anchor bolts and a base plate including dimensions, loads, calculations for tension in bolts, maximum force and required number of bolts, calculation of anchor bolt length, maximum bending moment in the base plate, and thickness of the base plate with stiffeners.

Uploaded by

Varun Verma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
73 views2 pages

Base Plate Detail - D

The document provides design details for anchor bolts and a base plate including dimensions, loads, calculations for tension in bolts, maximum force and required number of bolts, calculation of anchor bolt length, maximum bending moment in the base plate, and thickness of the base plate with stiffeners.

Uploaded by

Varun Verma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2

PROJECT:- DMRC
CLIENT:-
LOCATION:- NODE 926

ANCHOR BOLT AND BASE PLATE DESIGN DETAIL D

Grade of Concrete = M30


Maximum Bearing Pressure = 8.0 N/mm2

Grade of Base Plate = 345 Mpa

Grade of Anchor Bolt = 4.6

Column Section : 500 X 6.0


Web Depth Web thickness
200 X 10.0
Flange width Flange thickness
Provide Base Plate Size as:
Length of Base plate, L = 740 mm
Width of Base plate, B = 300 mm
Cantilever along length, a= 110 mm
Cantilever along width, b = 50 mm

LOADS DATA
LOAD COMB. VERTICAL(KN) SHEAR (KN) MOMENT(KN-m)
DL+LL+COL= 56.0 9.0 34.0
DL+WL= 27.0 7.4 59.0
DL+WL+CR= 27.0 7.5 59.0

Assume Diameter of bolts to be used = 24.0 mm


CG Of bolts in Tension 110.0 mm
Edge Distance in mm = 48

CALCULATIONS FOR TENSION IN BOLTS Kh=kx(L-a)


CASE I : DL+LL+COLL 48.0 62.0
500.0 mm
Calculating the value of K REF SP 40 PAGE 24 T

0.5x8xKx396900x(1-k/3) x 300-56x10^3x(370-110)-34x10^6=0
K * (1-K/3) = 0.10 110 mm 8N/mm2
K= 2.89 0.11
Kh
Kh = 1823.4 VALUE EXCEEDS THUS IGNORED
OR
66.6 * 740.0 mm
Kh = 66.6 mm
Force in Bolts : T = 23.89 KN
BEARING PRESSURE UNDER BASE PLATE
= (P / A) +( 6 x M ) / ( BxL^2)
= 1.49 N/mm2 < 8 N/mm2
[HENCE SAFE]
300mm
CASE 2 : DL+WL
Calculating the value of K
0.5x8xKx396900x(1-k/3) x 300+27x10^3x(370-110)-59x10^6=0 740mm
K * (1-K/3) = 0.11
K= 2.89 0.11
Kh = 1818.5 VALUE EXCEEDS THUS IGNORED
OR
71.5 *
Kh = 71.5 mm
Force in Bolts : T = 112.75 KN
BEARING PRESSURE UNDER BASE PLATE
= (P / A) +( 6 x M ) / ( BxL^2)
= 2.27 N/mm2 < 8 N/mm2
[HENCE SAFE]

CASE 3 : DL+WL+CR
Calculating the value of K
0.5x8xKx396900x(1-k/3) x 300+27x10^3x(370-110)-59x10^6=0
K * (1-K/3) = 0.11
K= 2.89 0.11
Kh = 1818.5 VALUE EXCEEDS THUS IGNORED
OR
71.5 *
Kh = 71.5 mm
Force in Bolts : T = 112.75 KN
BEARING PRESSURE UNDER BASE PLATE
= (P / A) +( 6 x M ) / ( BxL^2)
= 2.27 N/mm2 < 8 N/mm2
[HENCE SAFE]
Page 2 of 2

PROJECT:- DMRC
CLIENT:-
LOCATION:- NODE 926

MAXIMUM FORCE IN BOLTS = 112.8 KN


Maximum force in each bolt in tension = 22.6 KN

ζvf, cal = Calculated Shear Stress in Bolt in Kg/cm 2


σtf, cal = Calculated Axial Stress in Bolt in Kg/cm 2
ζvf = Permissible Shear in Bolt = 80 N/mm2 IS 1367 1967
σtf = Permissible Axial Tension in Bolt = 120 N/mm2
Factor for Permissible Stresses = 1.25 permissible stress is increased by 25%
Check: if the effect of wind in taken
2
ζvf, cal σtf, cal2
ζvf2
+ σtf2 ≤ 1.0

(7.4*1000)^2 112.8*1000
(N*452.2)^2 0.7*N/2*452.2
(80x1.25)^2
+ 120x1.25
≤ 1.0

0.000 + 0.208 = 0.21 ≤ 1.0 SAFE


<1 <1
SAFE SAFE

Number of bolts required are, N = 3.5 0


* Provide 10 no.s of 24 mm dia. Bolts

Calculation for anchor bolt length


Permissible bond stress of Plain bars in tension , ζ bd = 1.0 N/mm2
Anchorage length required = T/(3.14*ζbd*d*n)
Thus H = 299.2 mm SAFE
* Provide anchor length of 750 mm with 24mm dia. Anchor bolts

CALCULATION FOR MAXIMUM BENDING MOMENT IN BASE PLATE

ON TENSION SIDE :
M = 1.4 KN-m 71.5 mm

ON COMPRESSION SIDE (DL+LL+CR): 2.7


M = 3.7 KN-m
8 N/mm2
MAXIMUM MOMENT, M = 3.7 KN-m
48 mm
Thickness of base plate required for tension = 18.4 mm

Thickness of base plate required for compression = 17.0 mm

Maximum thickness of base plate = 18.4 mm

CALCULATION OF BASE PLATE THK. WITH STIFFNERS


Min.z reqd. = 16885.27017
Assuming thk of base plate. 25 mm
z of base plate= 31250.00
Thk of stiffners = 8 mm

C.G, y = b * t * t/2 + 0.5*b/2 * t1 * (t+1/3*b/2)


b * t + 0.5*b/2 * t1
y= 17.13 mm
Combined Z, = b *t3/12 + b * t * (y-t/2)2 + t1 * (b/4)3/12 + b/4*t1*(b/8+t-y)^2
y

Z= 120718.60 SAFE

* Thus, provide base plate of 740 mm X 300 mm X 25 mm


with Stiffners of 150 mm X 8 mm
150.0

t1

b/

You might also like