1002-1/Asia Dec 2010

Parker One Pneumatic Parker Global Air Preparation System

Parker Global
Air Preparation System

Parker Hannifin Corporation

Pneumatic Division - Asia
1
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

DECLARATION OF COMPLIANCE
(ROHS)
European Directive 2002/95/EC - RoHS (Restriction of use of certain Hazardous Substances in electrical and
electronic equipment), restricts the use of the 6 substances below in the manufacture of specified electrical
equipment.

Substance Concentration

LEAD: Product containing lead and its compounds (except for application of lead as an
alloying element by weight in steel up to 0.35%, in aluminum up to 0.4% and in
copper alloys up to 4% and in Circuit Board solder) must not exceed 0.1% by
weight.

MERCURY: The concentration level must not exceed 0.1% by weight.

CADMIUM: The concentration level must not exceed 0.01% by weight.

HEXAVALENT CHROMIUM:
This is a corrosive protective finish used on our product line. Were this finish is
utilized the Chromate solution is Hexavalent (Chrome 6) free.

POLYBROMINATED BIPHENYLS (PBB):

The concentration level must not exceed 0.1% by weight. This substance is not
known to be in any of our products.

POLYBROMINATED DIPHENYL ETHERS (PBDE):

The concentration level must not exceed 0.1% by weight. This substance is not
known to be in any of our products.

This information applies to product sold on or after 1st July, 2006

WARNING
!
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR
RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide
product and/or system options for further investigation by users h aving technical expertise. It is important that you analyze all
aspects of your application including consequences of any failure, and review the information concerning the product or system
in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the
user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and
assuring that all performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing,
are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its autho-
rized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this document
entitled “Offer of Sale”.

© Copyright 2010 Parker Hannifin Corporation. All Rights Reserved

Parker Hannifin Corporation

Pneumatic Division - Asia
2
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Introduction.......................................................................................................................4-13
Combos
P31 Mini Series.............................................................................................................. 14
P32 Compact Series...................................................................................................... 15
P33 Standard Series...................................................................................................... 16
Dimensions.................................................................................................................... 17
Filters
P31 Mini Series.........................................................................................................18-19
P32 Compact Series.................................................................................................20-21
P33 Standard Series.................................................................................................22-23
Coalescing & Adsorber Filters
P31 Mini Series.........................................................................................................24-25
P32 Compact Series.................................................................................................26-27
P33 Standard Series.................................................................................................28-29
Regulators
P31 Mini Series.........................................................................................................30-31
P31 Mini Common Port Regulator............................................................................32-33
P32 Compact Series.................................................................................................34-35
P32 Compact Common Port Regulator....................................................................36-37
P33 Standard Series.................................................................................................38-39
Filter / Regulators
P31 Mini Series.........................................................................................................40-41
P32 Compact Series.................................................................................................42-42
P33 Standard Series.................................................................................................44-45
Lubricators
P31 Mini Series.........................................................................................................46-47
P32 Compact Series.................................................................................................48-49
P33 Standard Series.................................................................................................50-51
Proportional Regulators
P31 Mini Series & P32 Compact Series....................................................................52-61
Combined Soft Start / Dump Valve.................................................................................62-63
Dump Valve.....................................................................................................................64-65
Soft Start Valve................................................................................................................66-67
Solenoid Operators.........................................................................................................68-69
Safety Lockout Valve............................................................................................................ 70
Modular Ball Valves.............................................................................................................. 71
Manifold Blocks.................................................................................................................... 72
Accessories
P31 Mini Series.............................................................................................................. 73
P32 Compact Series...................................................................................................... 74
P33 Standard Series...................................................................................................... 75
Accessories Kits.......................................................................................................76-78
Safety Guide....................................................................................................................80-81
Offer of Sale......................................................................................................................... 82
Parker Hannifin Corporation
Pneumatic Division - Asia
3
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Parker Global Air

Preparation System

Global.
Economical.
Modular.
Performance you need,
wherever you need it.

The comprehensive Global Air Preparation System is

available in three body sizes with either BSPP, BSPT,
or NPT to accommodate thread type requirements.

Full featured filters, regulators, filter/regulators,

and lubricators are available with a wide range of
standard options to meet air preparation needs.

Individual units can easily be assembled into various

combinations, utilizing patented modular lightweight
body connectors.

www.parker.com/globalfrl

Parker Hannifin Corporation

Pneumatic Division - Asia
4
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Comprehensive Offering

P31 Mini Series P32 Compact Series P33 Standard Series

1/4" ports 1/4", 3/8" and 1/2" 1/2" and 3/4"
40mm body width 60mm body width 73mm body width

Filters Regulators Filter / Regulators

• 5µ particulate, 1.0µ and 0.01µ • Available as stand alone, • Compact design for space
coalescing, and adsorber common port and electronic savings
available as standard proportional • Available with all the same
• Transparent or metal bowl • Both relieving and non- standard options as the filters
with manual or auto float relieving versions available and regulators
drains standard

Lubricators Combinations Accessories

• Proportional oil delivery over • Compact design for space • Solenoid operated soft start,
a wide range of air flows savings quick dump, and soft start/
• Fill under pressure • Easily assembled quick dump valves
• Many configurations available • Manifold blocks
• Shut-off valves (both slide
and ball type)
• Repair kits, gauges, etc.

Parker Hannifin Corporation

Pneumatic Division - Asia
5
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Together we can power your

application with clean, dry air
Fast cycle times, high product quality, and low downtime all require a clean, dry
pneumatic system to function properly. Parker has what it takes to make sure
pneumatic systems perform at their best.

Clean, dry pneumatic systems with

Parker Global Air Preparation

Stage 1 2
As air is compressed
to 7 bar (100 psig)
and higher, the relative
humidity quickly
For every 11°C (20°F)
that the air cools
after leaving the heat
3
4
of the compressor,
reaches 100% RH and
50% of the moisture Bulk liquid separators
air temperatures can
condenses into liquid remove condensed
reach between
into the system. liquids after the
110°C and 200°C

5
(230°F and 392°F). aftercooler, receiver,
The excess moisture or anywhere within the Particulate filters are
condenses and distribution system. used for the removal
collects in the receiver of solid particle
tank and distribution Bulk liquid separators contaminants down to
lines. This condensate also help protect 5 micron, as well as Coalescing filters are
must be removed. downstream filters the removal of designed to remove
in the system where condensed liquids water and oil aerosols
excess cooling takes (not vapor) and
place. Note: Water and oil, particulate from air
in vapor form, pass streams down to 0.01
through general micron in size.
purpose particulate
filters. Installed in pairs,
Particulate and
This type of filter Coalescing filters
should be used as ensure a continuous
Key a prefilter for the supply of high quality
coalescing (oil air.
Particulate removal) filter.
Oil
Water
Oil Vapor
Water Vapor

Parker Hannifin Corporation

Pneumatic Division - Asia
6
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Stages 1 2 3 4 5 6 7
Bulk Liquid Particulate Coalescing Hydrocarbon
Function Air Compressor Air Dryers
Removal Filtration Filtration Removal
All pneumatic Basic pneumatic Basic pneumatic Systems requiring Systems requiring Systems requiring
Application systems systems systems highest quality air. air with reduced highest quality air for
moisture content critical applications
Air leaving the Removes bulk Removes solid Removes liquid Removes water Removal of odors
compressor room at liquid contamination particulates down to aerosols and vapor from air and trace vapors for
93ºC (200ºF) releases and protects filters 5 micron, and submicron stream. Dew point critical applications.
95% of its moisture where excess cooling the separation of particulates (not reduced down to 4ºC
Description into the piping takes place in the bulk contaminants. vapor) down to (40ºF) (refrigeration)
system distribution piping 0.01 micron. or -40ºC (-40ºF)
when it cools to 38ºC (desiccant).
(100ºF)

Parker Customer P3TF P31, P32, P33 P31, P32, P33 PDRD P31, P32, P33
supplied Bulk Liquid Particulate Filter Coalescing Filter Refrigeration Dryer Activated Carbon
Global Air
Separator P3TJ (Adsorber) Filter
Preparation Regenerative
Solution Desiccant Dryer

Clean
Dry Air
6
Refrigeration and
desiccant dryers
lower the air's dew
point by removing
water vapor, providing
7
Hydrocarbon and oil
appropriately dry air vapors are removed
for the downstream using filters utilizing
application. activated carbon.
Airborne hydrocarbons
are often left over from
the compressor oils.

Parker Hannifin Corporation

Pneumatic Division - Asia
7
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

A completely modular
air preparation system
Easy to adjust non-
rising knob with
snap-lock, preventing
accidental change of
Filter set pressure.

Quick release
bayonet-type Regulator Pressure
integral bowl gauge
and bowl guard
assembly

Bowl guard
with multiple
viewing slots

Manual drain with

pipe-away, auto
drain available

Electronic Proportional Regulator

• Electro-Pneumatic regulator
• Integrated systems control
• Accurate output pressure
• Micro parameter settings
• Selectable I/O parameters
• Quick, full flow exhaust
• LED display indicates output pressure
• No air consumption in steady state
• Multiple mounting options
• Protection to IP65 P31P Mini Series P32P Compact Series

Parker Hannifin Corporation

Pneumatic Division - Asia
8
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Soft Start /
Combination knob
and sight-dome Quick Dump Valve
for adjusting the
precise amount of 2-piece Patented
lubrication modular body
connector US Patent
number 5,383,689
Large
filler plug

NPT, BSPP or
BSPT porting Aluminum
Lubricator available body

Can be filled
under pressure

Common Port Manifold Regulators

• Multiple output pressures (P2, P3, P4, etc.)
with common inlet (P1)
• Available in two sizes P31 and P32
• Balanced valve design for accurate pressure
regulation
• Outlet pressure ports in front and rear of unit. P1
• Four spring ranges available
P1
P4
P2 P3

Parker Hannifin Corporation

Pneumatic Division - Asia
9
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Air Preparation
P31 Mini Series
40mm body width
1/4" Ported
Flows up to: dm3/s (SCFM)
Filter 12 (25)
Coalescer 2 (4.2)
Regulator 30 (64)
Filter/Regulator 14 (30)
Lubricator 13 (28)
Features:
• Space saving integral gauge
• Manifold style regulators available
• OSHA compliant shut-off valves
• Soft-Start & Quick Dump valves
• Electronic Proportional Regulator

P32 Compact Series

60mm body width
1/4", 3/8", & 1/2" Ported
Flows up to: dm3/s (SCFM)
Filter 38 (80)
Coalescer 11 (23)
Regulator 67 (142)
Filter/Regulator 64 (136)
Lubricator 47 (100)
Features:
• Manifold style regulators available
• OSHA Compliant shut-off valves
• Soft-Start & Quick Dump valves
• Electronic Proportional Regulator

P33 Standard Series

73mm body width
1/2" & 3/4" Ported
Flows up to: dm3/s (SCFM)
Filter 48 (102)
Coalescer 20 (42)
Regulator 100 (212)
Filter/Regulator 98 (208)
Lubricator 68 (144)
Features:
• OSHA Compliant shut-off valves
• Soft-Start & Quick Dump valves
(Utilizes P32 size only)
• Electronic proportional regulator
(Utilizes P32 size only)

Parker Hannifin Corporation

Pneumatic Division - Asia
10
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Valves and Actuators

Mini Series Complimentary Products
The P31 Mini Series FRL’s and
accessories are well matched for
use with these Parker valves and
actuators.

Isys Micro
Moduflex Size 1

OSP-P P1D P1A

Compact Series Complimentary Products

The P32 Series FRL’s &
accessories are well matched for
use with these Parker valves and
actuators.

Isys Micro Isys HA / HB

P1D OSP-P

Standard Series Complimentary Products

The P33 Series FRL’s &
accessories are well matched for
use with these Parker valves and
actuators.

Isys Size 1 Isys HA / HB

P1D OSP-P

Parker Hannifin Corporation

Pneumatic Division - Asia
11
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Complete Pneumatic System

Pressure Regulation
Accurate pressure regulation is important to control forces, speeds, torque, dispensing, processes, etc. Parker has a
global solution to all of your pressure regulation needs, with support around the world.

Function Single Common Port Manifold Electronic Proportional

For pneumatic systems requiring For pneumatic systems requiring For pneumatic systems requiring an
single pressure regulation. multiple pressures for different parts electronic to pneumatic proportional
Description of the system, yet still having a control signal.
common inlet supply. Also allows pressure regulation to be
integrated into your control systems.

Parker Global
Air Preparation P31R, P32R, P33R P31H, P32H P31P, P32P fits Compact & Standard
Solution

Accessories
Today's sophisticated pneumatic systems need more than just FRL's. Often times peripheral accessory
products are needed to complete your pneumatic system. Parker has what is needed to ensure safe and reliable
start-ups, shut-downs, and lockouts, etc.

Soft Start / Manifold

Function Ball Valve Slide Valve Soft Start Quick Dump
Quick Dump Block
Soft Start
Function
Quick Dump
Slow Exhaust Slow Exhaust
Function
Solenoid, Air
Solenoid or Solenoid or
Operation Manual Twist Manual Slide
Air Pilot
Pilot, or Internal
Air Pilot
N/A
Air Pilot
Before or after Before or after Anywhere within
Placement FRL or stand FRL or stand After FRL After FRL After FRL FRL or stand
alone alone alone

Parker Global P31M Mini,

P31T Mini, P32T P31S Mini, P32S P31D Mini, P32D
P31V, P32V, P31V, P32V, P33M fits
Air Preparation P33V P33V
fits Compact & fits Compact & fits Compact &
Compact &
Solution Standard Standard Standard
Standard

Parker Hannifin Corporation

Pneumatic Division - Asia
12
1002-1/Asia Dec 2010
Parker One Pneumatic Parker Global Air Preparation Products

Application Guide
FRL to Valve: The chart below contains recommendations for the correct selection of Global Air Preparation units to
suit the number and size of valves in a typical application.
P31 Mini Series P32 Compact Series P33 Standard Series

Number of valves that would actuate at once

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Moduflex 1

Isys Micro

HB / Viking Xtreme

Moduflex 2

HA / Global ISO

See Larger Parker FRL Offering

Actuator to FRL: The chart below contains recommendations for the correct selection of Global Air Preparation
units suitable for each cylinder size.If you have a tube length over 2 m, choose one tube size larger than the chart. The
table is based on a Maximum cylinder speed of 0.5m/s
Cylinder bore size
Cyl Ø mm
Cyl Ø inches 5 10 16 20 25 28 32 40 45 50 63 75 80 100
(5/16) (7/16) (9/16) (3/4) (1) (1-1/8) (1-1/4) (1-1/2) (1-3/4) (2) (2-1/2) (3) (3-1/4) (4)
Tube diameter external
Tube Ø mm
Tube Ø inches 4 4 4 6 6 6 6 8 8 8 10 10 12 12
(5/32) (5/32) (5/32) (1/4) (1/4) (1/4) (1/4) (5/16) (5/16) (5/16) (3/8) (3/8) (1/2) (1/2)
1
2
Number of cylinders

3
actuating at once

4
5
6
7
8
9
10
P31 Mini Series P32 Compact Series P33 Standard Series

See Larger
Parker FRL Offering

Note: Data listed above is simply a guideline for a typical application only. Proper sizing
and correct flow requirements must be taken into account.

Parker Hannifin Corporation

Pneumatic Division - Asia
13
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Popular Combinations

Filter + Regulator + Lubricator Combinations + Poly bowl

5 micron element, 8 bar (116 psig) Regulator + Gauge and Wall Mounting Brackets
Inlet pressure 10 bar (145 psig), Secondary pressure 6.3 bar (91.3 psig),
1 bar (14.5 psig) pressure drop.
Port size Flow Manual Drain Weight Pulse Drain Weight
dm3/s (scfm)
1/4" 13 27 P31CB22GEMN6LNW 0.46 kg (1.01 lbs) P31CB22GEBN6LNW 0.46 kg (1.01 lbs)

Filter/Regulator + Lubricator Combinations + Poly bowl

5 micron element, 8 bar (116 psig) Regulator + Gauge and Wall Mounting Brackets
Inlet pressure 10 bar (145 psig), Secondary pressure 6.3 bar (91.3 psig),
1 bar (14.5 psig) pressure drop.
Port size Flow Manual Drain Weight Pulse Drain Weight
dm3/s (scfm)
1/4" 14 28 P31CA22GEMN6LNW 0.35 kg (0.77 lbs) P31CA22GEBN6LNW 0.35 kg (0.77 lbs)

Filter / Regulator coding

(use with codes: A M T)
Filter coding Regulator coding Lubricator coding Assembly
(use with combo codes: (use with combo codes: (use with combo configuration
B C D F G). For multiple B D E) codes: A B C E)
filters, repeat as needed

P31

Combination Thread type Element Relief / Adjustment Lub type Mounting

B/V + Combination Q BSPP 1 5µ Element E Non-rising knob N Oil mist No bracket A
Combination + B/V X BSPT 2 standard L
0.01µ Element C Port blocks C*
sight dome
Combination C NPT 9 Adjustment Range
1µ Element 9 Port blocks D*
Shut off + Combination Y With square gauge Drain type & wall brkt
Adsorber A
Combination + Shut off Z 2 bar (0.2 MPa) * 2 Wall bracket W
Port size No drain; N
4 bar (0.4 MPa) * 4 closed end
1/8 1
Combination type* Drain type 8 bar (0.8 MPa) ** 6 * For 3/8” Port
1/4 2 With round gauge Blocks please
F/R+L A F/R+Fc M Manual drain M
2 bar (0.2 MPa) Z order separately.
F+R+L B F+Fc1+Fc Q
Pulse drain B 4 bar (0.4 MPa) M See Kits section.
F+Fc F F/R+Fc+Fa T
8 bar (0.8 MPa) G
F+Fc+Fa G
Without guage
* Combination type
F = 5µ 2 bar (0.2 MPa) Y
Fc1 = 1µ Bowl type 4 bar (0.4 MPa) L
Fc = .01µ Poly bowl with bowl guard G 8 bar (0.8 MPa) N
Fa = Adsorber
Metal bowl without sight gauge M * With 0-0.4 MPa guage
** With 0-1.1 MPa guage
Note: All bowl types are the same
for each component
Example: If a “G” is specified for a
F+L, both units would get a poly bowl
with bowl guard.

Parker Hannifin Corporation

Pneumatic Division - Asia
14
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Popular Combinations

Filter + Regulator + Lubricator Combinations + Poly bowl

5 micron element, 8 bar (116 psig) Regulator + Gauge and Wall Mounting Brackets
Inlet pressure 10 bar (145 psig), Secondary pressure 6.3 bar (91.3 psig),
1 bar (14.5 psig) pressure drop.
Port size Flow Manual Drain Weight Auto Drain Weight
dm3/s (scfm)
1/4" 20 42 P32CB22GEMNGLNW 1.29 kg (2.84 lbs) P32CB22GEANGLNW 1.29 kg (2.84 lbs)
3/8" 32 68 P32CB23GEMNGLNW 1.29 kg (2.84 lbs) P32CB23GEANGLNW 1.29 kg (2.84 lbs)
1/2" 40 85 P32CB24GEMNGLNW 1.29 kg (2.84 lbs) P32CB24GEANGLNW 1.29 kg (2.84 lbs)

Filter/Regulator + Lubricator Combinations + Poly bowl

5 micron element, 8 bar (116 psig) Regulator + Gauge and Wall Mounting Brackets
Inlet pressure 10 bar (145 psig), Secondary pressure 6.3 bar (91.3 psig),
1 bar (14.5 psig) pressure drop.
Port size Flow Manual Drain Weight Auto Drain Weight
dm3/s (scfm)
1/4" 22 45 P32CA22GEMNGLNW 1.03 kg (2.27 lbs) P32CA22GEANGLNW 1.03 kg (2.27 lbs)
3/8" 33 70 P32CA23GEMNGLNW 1.03 kg (2.27 lbs) P32CA23GEANGLNW 1.03 kg (2.27 lbs)
1/2" 43 90 P32CA24GEMNGLNW 1.03 kg (2.27 lbs) P32CA24GEANGLNW 1.03 kg (2.27 lbs)
Filter / Regulator coding
(use with codes: A M T)
Filter coding Regulator coding Lubricator coding Assembly
(use with combo codes: (use with combo codes: (use with combo configuration
B C D F G). For multiple B D E W) codes: A B C E)
filters, repeat as needed

P32

Combination Thread type Element Relief / Adjustment Lub type Mounting

B/V + Combination Q BSPP 1 5µ Element E Non-rising knob N Oil mist No bracket A
Combination + B/V X BSPT 2 relieving standard L
0.01µ Element C Port blocks C
sight dome
Combination C NPT 9
0.01µ Element D Port blocks D
Shut off + Combination Y with dpi Drain type & wall brkt
Adjustment range
Combination + Shut off Z 1µ Element 9 Wall bracket W
Port size With round gauge No drain; N
1/4 2 1µ Element Q closed end
Combination type* 2 bar; 30 psig; 0.2 MPa Z
3/8 3 with dpi
F/R+L A F/R+Fc M 4 bar; 60 psig; 0.4 MPa M
1/2 4 Adsorber A
F+R+L B F+Fc1+Fc Q 8 bar; 125 psig; 0.8 MPa G
F+Fc F F/R+Fc+Fa T 17 bar; 250 psig; 1.7 MPa J
F+Fc+Fa G Drain type Without gauge
* Combination type 2 bar; 30 psig; 0.2 MPa Y
Auto drain A
F = 5µ 4 bar; 60 psig; 0.4 MPa L
Fc1 = 1µ Bowl type Manual drain M
Fc = .01µ 8 bar; 125 psig; 0.8 MPa N
Poly bowl with bowl guard G
Fa = Adsorber 17 bar; 250 psig; 1.7 MPa H
Metal bowl without sight gauge M
Metal bowl with sight gauge S
Note: All bowl types are the same
for each component
Example: If a “G” is specified for a
F+L, both units would get a poly bowl
with bowl guard.

Parker Hannifin Corporation

Pneumatic Division - Asia
15
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Popular Combinations

Filter + Regulator + Lubricator Combinations + Poly bowl

5 micron element, 8 bar (116 psig) Regulator + Gauge and Wall Mounting Brackets
Inlet pressure 10 bar (145 psig), Secondary pressure 6.3 bar (91.3 psig),
1 bar (14.5 psig) pressure drop.

Port size Flow Manual Drain Weight Auto Drain Weight

dm3/s (scfm)
1/2" 43 90 P33CB24GEMNGLNW 1.84 kg (4.06 lbs) P33CB24GEANGLNW 1.84 kg (4.06 lbs)
3/4" 52 110 P33CB26GEMNGLNW 1.84 kg (4.06 lbs) P33CB26GEANGLNW 1.84 kg (4.06 lbs)

Filter/Regulator + Lubricator Combinations + Poly bowl

5 micron element, 8 bar (116 psig) Regulator + Gauge and Wall Mounting Brackets
Inlet pressure 10 bar (145 psig), Secondary pressure 6.3 bar (91.3 psig),
1 bar (14.5 psig) pressure drop.
Port size Flow Manual Drain Weight Auto Drain Weight
dm3/s (scfm)
1/2" 52 110 P33CA24GEMNGLNW 1.51 kg (3.33 lbs) P33CA24GEANGLNW 1.51 kg (3.33 lbs)
3/4" 71 150 P33CA26GEMNGLNW 1.51 kg (3.33 lbs) P33CA26GEANGLNW 1.51 kg (3.33 lbs)

Filter / Regulator coding

(use with codes: A M T)
Filter coding Regulator coding Lubricator coding Assembly
(use with combo codes: (use with combo codes: (use with combo configuration
B C D F G). For multiple B D E W) codes: A B C E)
filters, repeat as needed

P33

Combination Thread type Element Relief / Adjustment Lub type Mounting

B/V + Combination Q BSPP 1 5µ Element E Non-rising knob N Oil mist No bracket A
Combination + B/V X BSPT 2 relieving standard L
0.01µ Element C Port blocks C
sight dome
Combination C NPT 9
0.01µ Element D Port blocks D
Shut off + Combination Y with dpi Drain type & wall brkt
Adjustment range
Combination + Shut off Z Port size 1µ Element 9 Wall bracket W
With round gauge No drain; N
1/2 4 1µ Element Q closed end
Combination type* 2 bar; 30 psig; 0.2 MPa Z
3/4 6 with dpi
F/R+L A F/R+Fc M 4 bar; 60 psig; 0.4 MPa M
Adsorber A 8 bar; 125 psig; 0.8 MPa G
F+R+L B F+Fc1+Fc Q
F+Fc F F/R+Fc+Fa T 17 bar; 250 psig; 1.7 MPa J
F+Fc+Fa G Drain type Without gauge
* Combination type 2 bar; 30 psig; 0.2 MPa Y
Auto drain A
F = 5µ 4 bar; 60 psig; 0.4 MPa L
Fc1 = 1µ Bowl type Manual drain M
Fc = .01µ 8 bar; 125 psig; 0.8 MPa N
Poly bowl with bowl guard G
Fa = Adsorber 17 bar; 250 psig; 1.7 MPa H
Metal bowl without sight gauge M
Metal bowl with sight gauge S
Note: All bowl types are the same
for each component
Example: If a “G” is specified for a
F+L, both units would get a poly bowl
with bowl guard.

Parker Hannifin Corporation

Pneumatic Division - Asia
16
1002-1/Asia Dec 2010
Parker One Pneumatic P31, P32, P33 Series

Popular Combination Dimensions

P31C
80 77
(3.15) (3.03) 120 77
(4.72) (3.03)
40 41
(1.57) (1.61) 40 40 41
(1.57) (1.57) (1.61)

35
35 (1.38)
(1.38)

35 155.2
35 164.1 (1.38) (6.11)
(1.38) (6.46)

Bowl 4mm (5/32") 33.3 Bowl

4mm (5/32") 33.3 removal I.D. Tube (1.31) removal
I.D. Tube (1.31) clearance Barb fitting clearance
Barb fitting

P32C
115
(4.53)
129 47.1
(5.08) (1.85)
198 115
(7.80) (4.53)
64.5
(2.54) 64.5 69 47.1
(2.54) (2.72) (1.85)

50 50
(3.94) (3.94)

100 100
(3.94) (3.94)

254
(10.0)
222
(10.0)

Bowl Bowl
removal removal
4.8 mm (.19) 41 clearance. 4.8 mm (.19) 41 clearance.
I.D. Tube (1.6) (Manual and I.D. Tube (1.6) (Manual and
Barb fitting Auto Drain.) Barb fitting Auto Drain.)

P33C
120
155 (4.72)
(6.10) 47.1
(1.85)
237 120
77.5 (9.33) (4.72)
(3.05) 77.5 82 47.1
(3.05) (3.23) (1.85)

50 50
(3.94) (3.94)
100 100
(3.94) (3.94)

291 238
(11.44) (9.37)

Bowl Bowl
4.8 mm (.19) removal 4.8 mm (.19) removal
51 clearance. 51 clearance.
I.D. Tube (2.00) (Manual and I.D. Tube (2.00) (Manual and
Barb fitting Barb fitting
Auto Drain.) Auto Drain.)

Parker Hannifin Corporation

Pneumatic Division - Asia
17
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Mini Particulate Filter - P31 Symbols

1 2 1 2

Manual drain Auto drain

• Integral 1/4" ports (NPT, BSPP & BSPT)

• High efficiency 5 micron element as standard
• Excellent water removal efficiency
• Robust but lightweight aluminum construction
• One hand operation for easy element cartridge removal
• Positive bayonet latch to ensure correct & safe fitting

Options:

P31 FA E N

Thread type Port size Bowl type Mounting

1/8 1
BSPP 1 Poly bowl with bowl guard G No bracket N
1/4 2
BSPT 2 Metal bowl without sight gauge M
NPT 9
Element Drain type
5µ Element E Pulse drain B
Manual drain M

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" Poly bowl - Manual drain P31FA22EGMN 12 (25) 10 (150) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

1/4" Poly bowl - Pulse drain P31FA22EGBN 12 (25) 10 (150) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

1/4" Metal bowl - Manual drain P31FA22EMMN 12 (25) 17 (250) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

1/4" Metal bowl - Pulse drain P31FA22EMBN 12 (25) 17 (250) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.34 (4.9 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options
chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
18
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Specifications Flow Charts

Flow Capacity* 1/4 12 dm /s (25 scfm)
3

1/4 Filter Primary Pressure - bar 1.6 4.0 6.3 10

Max. Operating Plastic Bowl 52°C (125°F) Primary Pressure - psig 23.2 58 91.4 145
7 0.5
Temperature Metal Bowl 65.5°C (150°F)
6 0.4

Pressure Drop - (psig)

Max. Supply Plastic Bowl 10 bar (150 psig)

Pressure Drop - bar

5
Pressure Metal Bowl 17 bar (250 psig) 4
0.3

Standard Filtration 5 Micron 3 0.2

2
Useful Retention †
12 cm (0.4 US oz.)
3
1
0.1

Port Size BSPP / BSPT / NPT 1/8, 1/4 0 0

0 5 10 15 20
Flow - dm3/s
Weight 0.11 kg (0.24 lbs) 0 10 20 30 40
* Inlet pressure 6.3 bar (91.3 psig). Pressure drop 0.34 bar (4.9 psig). Flow - (scfm)
†
Useful retention refers to volume below the quiet zone baffle.
Air quality:
Within ISO 8573-1: 1991 Class 3 (Particulates)
Within ISO 8573-1: 2001 Class 6 (Particulates)

Materials of Construction
Body Aluminum
Body Cap ABS
Bowl Polycarbonate
Bowl Guard Nylon
Element Retainer Acetal
Baffle Acetal
Filter Element Sintered Polyethylene
Seals Nitrile

Dimensions Repair and Service Kits

Plastic bowl / Bowl guard manual drain P31KA00BGM
42.7 Metal bowl / w/o sight gauge manual drain P31KA00BMM
(1.68)
40.0 21.3 Plastic bowl / Bowl guard pulse drain P31KA00BGB
(1.58) (0.84)
Metal bowl / w/o sight gauge pulse drain P31KA00BMB
18.3 5µ particle filter element P31KA00ESE
(0.72)
C-Bracket (fits to body) P31KA00MW
T-Bracket with body connector P31KA00MT
Body connector P31KA00CB
116.3
(4.58)

4mm (5/32") Bowl

I.D. Tube 33.3 removal
Barb fitting (1.31) clearance

Parker Hannifin Corporation

Pneumatic Division - Asia
19
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Compact Particulate Filter - P32 Symbols

1 2 1 2

Manual drain Auto drain

• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)

• High efficiency 5 micron element as standard
• Excellent water removal efficiency
• Robust but lightweight aluminum construction
• Positive bayonet latch to ensure correct & safe fitting

Options:

P32 FA E N

Thread type Port size Bowl type Mounting

BSPP 1 1/4 2 Poly bowl with bowl guard G No bracket N
BSPT 2 3/8 3 Metal bowl without sight gauge M
NPT 9 1/2 4 Metal bowl with sight gauge S

Element Drain type

5µ Element E Manual drain M
Auto drain A

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" Poly bowl - Manual drain P32FA22EGMN 18 (38) 10 (150) 188 (7.4) 60 (2.36) 60 (2.36)

1/4" Poly bowl - Auto drain P32FA22EGAN 18 (38) 10 (150) 182 (7.2) 60 (2.36) 60 (2.36)

1/4" Metal bowl - Manual drain P32FA22ESMN 18 (38) 17 (250) 188 (7.4) 60 (2.36) 60 (2.36)

1/4" Metal bowl - Auto drain P32FA22ESAN 18 (38) 17 (250) 182 (7.2) 60 (2.36) 60 (2.36)

3/8" Poly bowl - Manual drain P32FA23EGMN 30 (64) 10 (150) 188 (7.4) 60 (2.36) 60 (2.36)

3/8" Poly bowl - Auto drain P32FA23EGAN 30 (64) 10 (150) 182 (7.2) 60 (2.36) 60 (2.36)

3/8" Metal bowl - Manual drain P32FA23ESMN 30 (64) 17 (250) 188 (7.4) 60 (2.36) 60 (2.36)

3/8" Metal bowl - Auto drain P32FA23ESAN 30 (64) 17 (250) 182 (7.2) 60 (2.36) 60 (2.36)

1/2" Poly bowl - Manual drain P32FA24EGMN 38 (80) 10 (150) 188 (7.4) 60 (2.36) 60 (2.36)

1/2" Poly bowl - Auto drain P32FA24EGAN 38 (80) 10 (150) 182 (7.2) 60 (2.36) 60 (2.36)

1/2" Metal bowl - Manual drain P32FA24ESMN 38 (80) 17 (250) 188 (7.4) 60 (2.36) 60 (2.36)

1/2" Metal bowl - Auto drain P32FA24ESAN 38 (80) 17 (250) 182 (7.2) 60 (2.36) 60 (2.36)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.34 (4.9 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options
chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
20
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Specifications Flow Charts

Flow Capacity* 1/4 18 dm3/s (38 scfm) 1/4 Filter Primary Pressure - bar 1.6 4.0 6.3 10
3/8 30 dm3/s (64 scfm) 0.5
Primary Pressure - psig 23.2 58 91.4 145
7
1/2 38 dm3/s (80 scfm) 6 0.4

Pressure Drop - (psig)

Operating Plastic Bowl 52°C (125°F)

Pressure Drop - bar

5
Temperature Metal Bowl 65.5°C (150°F) 4
0.3

Max. Supply Plastic Bowl 10 bar (150 psig) 3 0.2

Pressure Metal Bowl 17 bar (250 psig) 2

0.1
Standard Filtration 5 Micron 1

0 0
Useful Retention† 51 cm3 (1.7 US oz.) 0 10 20 30
Flow - dm3/s
Port Size BSPP / BSPT / NPT 1/4, 3/8, 1/2 0 10 20 30 40 50 60
Flow - (scfm)
Weight 0.28 kg (0.62 lbs)
3/8 Filter
* Inlet pressure 6.3 bar (91.3 psig). Pressure drop 0.34 bar (4.9 psig). Primary Pressure - bar 1.6 4.0 6.3 10
Primary Pressure - psig 23.2 58 91.4 145
†
Useful retention refers to volume below the quiet zone baffle. 7 0.5
Air quality: 6 0.4

Pressure Drop - (psig)

Within ISO 8573-1: 1991 Class 3 (Particulates)

Pressure Drop - bar

5
Within ISO 8573-1: 2001 Class 6 (Particulates) 0.3
4

3 0.2
Materials of Construction 2
0.1
Body Aluminum 1

Body Cap ABS 0 0

0 10 20 30 40 50
Flow - dm3/s
Bowls Plastic Bowl Polycarbonate
0 20 40 60 80 100
Metal Bowl Aluminum Flow - (scfm)

Bowl Guard Nylon 1/2 Filter Primary Pressure - bar 1.6 4.0 6.3 10
Primary Pressure - psig 23.2 58 91.4 145
Deflector Polypropylene 7 0.5
Element Retainer / Baffle Acetal 6 0.4
Pressure Drop - (psig)

Pressure Drop - bar

Filter Element Sintered Polyethylene 5

0.3
Seals Plastic Bowl Nitrile 4

Metal Bowl Nitrile 3 0.2

Sight Gauge Metal Bowl Polycarbonate 2

0.1
1

0 0
0 10 20 30 40 50 60
Flow - dm3/s
0 20 40 60 80 100 120
Flow - (scfm)

Dimensions
Repair and Service Kits
60
60.0 30 (2.36) Plastic bowl / Bowl guard manual drain P32KA00BGM
(2.36) (1.18)
Metal bowl / Sight gauge manual drain P32KA00BSM
26 Auto drain P32KA00DA
(1.0)
5µ particle filter element P32KA00ESE
L-Bracket (fits to body) P32KA00ML
T-Bracket (fits to body connector) P32KA00MB
T-Bracket with body connector P32KA00MT
188 Body connector P32KA00CB
(7.4)
Differential pressure indicator (replacement) P32KA00RQ

Use 10mm
or 3/8" Flex
Bowl
4.8 mm (.19") Tubing
removal
I.D. Tube 41 clearance.
Barb fitting (1.6)
(Manual and
Auto Drain.)
Manual Drain Automatic Drain

Parker Hannifin Corporation

Pneumatic Division - Asia
21
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Standard Particulate Filter - P33 Symbols

1 2 1 2

Manual drain Auto drain

• Integral 1/2" or 3/4" ports (NPT, BSPP & BSPT)

• High efficiency 5 micron element as standard
• Excellent water removal efficiency
• Robust but lightweight aluminum construction
• Positive bayonet latch to ensure correct & safe fitting

Options:

P33 FA E N

Thread type Port size Bowl type Mounting

BSPP 1 1/2 4 Poly bowl with bowl guard G No bracket N
BSPT 2 3/4 6 Metal bowl without sight gauge M
NPT 9 Metal bowl with sight gauge S

Element Drain type

5µ Element E Manual drain M
Auto drain A

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/2" Poly bowl - Manual drain P33FA24EGMN 40 (85) 10 (150) 213 (8.4) 73 (2.9) 73 (2.9)

1/2" Poly bowl - Auto drain P33FA24EGAN 40 (85) 10 (150) 207 (8.2) 73 (2.9) 73 (2.9)

1/2" Metal bowl - Manual drain P33FA24ESMN 40 (85) 17 (250) 213 (8.4) 73 (2.9) 73 (2.9)

1/2" Metal bowl - Auto drain P33FA24ESAN 40 (85) 17 (250) 207 (8.2) 73 (2.9) 73 (2.9)

3/4" Poly bowl - Manual drain P33FA26EGMN 48 (102) 10 (150) 213 (8.4) 73 (2.9) 73 (2.9)

3/4" Poly bowl - Auto drain P33FA26EGAN 48 (102) 10 (150) 207 (8.2) 73 (2.9) 73 (2.9)

3/4" Metal bowl - Manual drain P33FA26ESMN 48 (102) 17 (250) 213 (8.4) 73 (2.9) 73 (2.9)

3/4" Metal bowl - Auto drain P33FA26ESAN 48 (102) 17 (250) 207 (8.2) 73 (2.9) 73 (2.9)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.34 (4.9 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options
chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
22
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Specifications Flow Charts

Flow Capacity* 1/2 40 dm3/s (85 scfm) 1/2 Filter Primary Pressure - bar 1.6 4.0 6.3 10
3/4 48 dm3/s (102 scfm) 0.5
Primary Pressure - psig 23.2 58 91.4 145
7
Max. Operating Plastic Bowl 52°C (125°F)
6 0.4

Pressure Drop - (psig)

Temperature Metal Bowl 65.5°C (150°F)

Pressure Drop - bar

5
Max. Supply Plastic Bowl 10 bar (150 psig) 4
0.3

Pressure Metal Bowl 17 bar (250 psig) 3 0.2

Standard Filtration 5 Micron 2
0.1
Useful Retention† 85 cm3 (2.8 US oz.) 1

Port Size BSPP / BSPT / NPT 1/2, 3/4 0 0

0 10 20 30 40 50 60 70
Flow - dm3/s
Weight 0.46 kg (1.01 lbs)
0 20 40 60 80 100 120 140
Flow - (scfm)
* Inlet pressure 6.3 bar (91.3 psig). Pressure drop 0.34 bar (4.9 psig).
†
Useful retention refers to volume below the quiet zone baffle.
Air quality:
Within ISO 8573-1: 1991 Class 3 (Particulates) 3/4 Filter Primary Pressure - bar 1.6 4.0 6.3 10
Within ISO 8573-1: 2001 Class 6 (Particulates) 0.5
Primary Pressure - psig 23.2 58 91.4 145
7
6 0.4

Pressure Drop - (psig)

Materials of Construction

Pressure Drop - bar

5
0.3
Body Aluminum 4

Body Cap ABS 3 0.2

2
Bowls Plastic Bowl Polycarbonate 0.1
1
Metal Bowl Aluminum 0 0
Bowl Guard Nylon 0 10 20 30 40
Flow - dm3/s
50 60 70 80

Deflector Polypropylene 0 20 40 60 80 100 120 140 160

Flow - (scfm)
Element Retainer / Baffle Acetal
Filter Element Sintered Polyethylene
Seals Plastic Bowl Nitrile
Metal Bowl Nitrile
Sight Gauge Metal Bowl Polycarbonate

Dimensions Repair and Service Kits

73
Plastic bowl / Bowl guard manual drain P33KA00BGM
73 (2.9)
36
(2.9) (1.4) Metal bowl / Sight gauge manual drain P33KA00BSM
26 Auto drain P32KA00DA
(1.0)
5µ particle filter element P33KA00ESE
L-Bracket (fits to body) P33KA00ML
T-Bracket (fits to body connector) P32KA00MB
T-Bracket with body connector P33KA00MT
213 Body connector P32KA00CB
(8.4)
Differential pressure indicator (replacement) P32KA00RQ

Use 10mm
Bowl or 3/8" Flex
4.8 mm (.19)
removal Tubing
I.D. Tube 51 clearance.
Barb fitting (2.0) (Manual and

Manual Drain Auto Drain.) Automatic Drain

Parker Hannifin Corporation

Pneumatic Division - Asia
23
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Mini Coalescing and Adsorber Filters - P31

• Integral 1/4" ports (NPT, BSPP & BSPT)
• Removes liquid aerosols and sub micron particles
• Oil free air for critical applications, such as air gauging,
pneumatic instrumentation and control
• Positive bayonet latch to ensure correct & safe fitting
• Adsorbing activated carbon element removes oil vapors
and most hydrocarbons

Note: To optimize the life of coalescing element, it is

advisable to install a P31F pre-filter with a 5 micron
element upstream of the coalescing filter.
To optimize the life of an Adsorber it is advisable
to install a P31 Coalescing Filter upstream of the
Adsorber. Adsorber element should be replaced
Options: approximately every 1000 hours of service.

P31 FA N

Thread type Port size Bowl type Mounting

1/8 1
BSPP 1 Poly bowl with bowl guard G No bracket N
1/4 2
BSPT 2 Metal bowl without sight gauge M
NPT 9
Element Drain type
0.01µ Element C Pulse drain B
1µ Element 9 Manual drain M
Adsorber A

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" Poly bowl - 0.01 micron - Manual drain P31FA22CGMN 2 (4.2) 10 (150) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

1/4' Poly bowl - 0.01 micron - Pulse drain P31FA22CGBN 2 (4.2) 10 (150) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

1/4" Metal bowl - 0.01 micron - Manual drain P31FA22CMMN 2 (4.2) 17 (250) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

1/4' Metal bowl - 0.01 micron - Pulse drain P31FA22CMBN 2 (4.2) 17 (250) 116.3 (4.58) 40 (1.58) 42.7 (1.68)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.2 (3 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options
chart above.

Indicates stocked product.

Parker Hannifin Corporation

Pneumatic Division - Asia
24
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Specifications Flow Charts

Flow Capacity dm3/s SCFM P31 - 1.0 micron flow
1.0 Micron Coalescing Energy Efficient Flow* 3.8 (8) Primary Pressure - bar 2.0 4.0 6.3
Maximum Flow** 6 (13) 0.5
Primary Pressure - psig 29 58 91.4
7
Activated Carbon Adsorber Rated Flow* 6 (13)
6 0.4
Max.. Operating Plastic Bowl 52°C (125°F)

Pressure Drop - (psig)

Pressure Drop - bar

5
Temperature Metal Bowl 65.5°C (150°F) 0.3
4
Max. Supply Plastic Bowl 10 bar (150 psig)
3 0.2
Pressure Metal Bowl 17 bar (250 psig)
2 Saturated
Standard Filtration 1.0 and 0.01 Micron 0.1 Element
1 Flow
ppm wt
0 0
Adsorber Max. oil carryover (ppm w/w) 0.003 @ 21OC (70OF) 0 1 2 3 4
Flow - dm3/s
5 6 7 8

Useful Retention† 12 cm3 (0.4 US oz.) 0 5 10 15

Flow - (scfm)
Port Size BSPP / BSPT / NPT 1/4
Weight 0.11 kg (0.24 lbs)
* Inlet pressure 6.3 bar (91.3 psig), Pressure drop 0.2 bar (3 psig),
Saturated Element.
** Inlet pressure 6.3 bar (91.3 psig), Pressure drop 0.4 bar (6 psig),
Saturated Element.
†
Useful retention refers to volume below the quiet zone baffle.

Materials of Construction
Body Aluminum
Body Cap ABS
Bowl Plastic Bowl Polycarbonate
Metal Bowl Aluminum
Filter Element 1.0 and .01 Micron Borosilicate Cloth
Adsorber Activated Carbon
Seals Nitrile

Dimensions Repair and Service Kits

42.7 Plastic bowl / Bowl guard manual drain P31KA00BGM
40.0 (1.68)
(1.58) 21.3 Metal bowl / w/o sight gauge manual drain P31KA00BMM
(0.84)
Plastic bowl / Bowl guard pulse drain P31KA00BGB
18.3 Metal bowl / w/o sight gauge pulse drain P31KA00BMB
(0.72)
1µ coalescing filter element P31KA00ES9
0.01µ coalescing filter element P31KA00ESC
Activated carbon adsorber filter element P31KA00ESA
116.3
(4.58) C-Bracket (fits to body) P31KA00MW
T-Bracket with body connector P31KA00MT
Body connector P31KA00CB

4mm (5/32") Bowl

I.D. Tube 33.3
removal
Barb fitting (1.31)
clearance

Parker Hannifin Corporation

Pneumatic Division - Asia
25
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Compact Coalescing and Adsorber Filter - P32

• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)
• Removes liquid aerosols and sub micron particles
• Oil free air for critical applications, such as air gauging,
pneumatic instrumentation and control
• Differential Pressure Indicator (DPI) standard on
Coalescing Filters
• Positive bayonet latch to ensure correct & safe fitting
• Adsorbing activated carbon element removes oil vapors and
most hydrocarbons

Note: To optimize the life of coalescing element, it is

advisable to install a P32F pre-filter with a 5 micron
element upstream of the coalescing filter.
To optimize the life of an Adsorber it is advisable
to install a P32 Coalescing Filter upstream of the
Adsorber. Adsorber element should be replaced
Options: approximately every 1000 hours of service.

P32 FA N

Thread type Port size Bowl type Mounting

BSPP 1 1/4 2 Poly bowl with bowl guard G No bracket N
BSPT 2 3/8 3 Metal bowl without sight gauge M
NPT 9 1/2 4 Metal bowl with sight gauge S

Element Drain type

0.01µ Element C Manual drain M
0.01µ Element with dpi D Auto drain A
1µ Element 9
1µ Element with dpi Q
Adsorber A

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" Poly bowl - 0.01 Micron, Manual drain P32FA22DGMN 11 (23) 10 (150) 209 (8.2) 60 (2.36) 60 (2.36)

1/4" Poly bowl - 0.01 Micron, Auto drain P32FA22DGAN 11 (23) 10 (150) 203 (8.0) 60 (2.36) 60 (2.36)

1/4" Metal bowl - 0.01 Micron, Manual drain P32FA22DSMN 11 (23) 17 (250) 209 (8.2) 60 (2.36) 60 (2.36)

1/4" Metal bowl - 0.01 Micron, Auto drain P32FA22DSAN 11 (23) 17 (250) 203 (8.0) 60 (2.36) 60 (2.36)

3/8" Poly bowl - 0.01 Micron, Manual drain P32FA23DGMN 11 (23) 10 (150) 209 (8.2) 60 (2.36) 60 (2.36)

3/8" Poly bowl - 0.01 Micron, Auto drain P32FA23DGAN 11 (23) 10 (150) 203 (8.0) 60 (2.36) 60 (2.36)

3/8" Metal bowl - 0.01 Micron, Manual drain P32FA23DSMN 11 (23) 17 (250) 209 (8.2) 60 (2.36) 60 (2.36)

3/8' Metal bowl - 0.01 Micron, Auto drain P32FA23DSAN 11 (23) 17 (250) 203 (8.0) 60 (2.36) 60 (2.36)

1/2" Poly bowl - 0.01 Micron, Manual drain P32FA24DGMN 11 (23) 10 (150) 209 (8.2) 60 (2.36) 60 (2.36)

1/2" Poly bowl - 0.01 Micron, Auto drain P32FA24DGAN 11 (23) 10 (150) 203 (8.0) 60 (2.36) 60 (2.36)

1/2" Metal bowl - 0.01 Micron, Manual drain P32FA24DSMN 11 (23) 17 (250) 209 (8.2) 60 (2.36) 60 (2.36)

1/2" Metal bowl - 0.01 Micron, Auto drain P32FA24DSAN 11 (23) 17 (250) 203 (8.0) 60 (2.36) 60 (2.36)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.2 (3 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options
chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
26
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Specifications Flow Charts

Flow Capacity dm3/s SCFM P32 - 1.0 micron flow
1.0 Micron Coalescing Energy Efficient Flow* 17 (36) Primary Pressure - bar 2.0 4.0 6.3
Primary Pressure - psig 29 58 91.4
Maximum Flow** 27 (57) 7 0.5

0.01 Micron Coalescing Energy Efficient Flow* 11 (23) 6 0.4

Pressure Drop - (psig)

Pressure Drop - bar

Maximum Flow** 28 (38) 5
Activated Carbon Adsorber Rated Flow* 27 (57) 4
0.3

Max. Operating Plastic Bowl 52°C (125°F) 3 0.2

Temperature Metal Bowl 65.5°C (150°F) 2 Saturated
0.1 Element
Max. Supply Plastic Bowl 10 bar (150 psig) 1 Flow

Pressure Metal Bowl 17 bar (250 psig) 0 0

0 5 10 15 20 25 30 35
Standard Filtration 1.0 and 0.01 Micron Flow - dm3/s

ppm wt 0 10 20 30 40
Flow - (scfm)
50 60 70

Adsorber Max. oil carryover (ppm w/w) 0.003 @ 21OC (70OF)

Useful Retention† 51 cm3 (1.7 US oz.) P32 - 0.01 micron flow
Port Size BSPP / BSPT / NPT 1/4, 3/8, 1/2
Primary Pressure - bar 2.0 4.0 6.3
Weight 0.32 kg (0.71 lbs) 0.5
Primary Pressure - psig 29 58 91.4
7
* Inlet pressure 6.3 bar (91.3 psig), Pressure drop 0.2 bar (3 psig),
6
Saturated Element. 0.4

Pressure Drop - (psig)

Pressure Drop - bar

** Inlet pressure 6.3 bar (91.3 psig), Pressure drop 0.4 bar (6 psig), 5
0.3
Saturated Element. 4
†
Useful retention refers to volume below the quiet zone baffle. 3 0.2
2 Saturated
0.1 Element
1 Flow

0 0
0 5 10 15 20 25
Flow - dm3/s
0 10 20 30 40 50
Flow - (scfm)

Materials of Construction

Body Aluminum
Dimensions
Body Cap ABS
60.0 60
Bowls Plastic Bowl Polycarbonate
(2.36) (2.36) Metal Bowl Aluminum
DPI 30
(1.18) Filter Element 1.0 and .01 Micron Borosilicate Cloth
Adsorber Activated Carbon
48 Seals Nitrile
(1.9)
Sight Gauge Metal Bowl Polycarbonate

Repair and Service Kits

Plastic bowl / Bowl guard manual drain P32KA00BGM
209 Metal bowl / Sight gauge manual drain P32KA00BSM
(8.2)
Auto drain P32KA00DA
1µ coalescing filter element P32KA00ES9
0.01µ coalescing filter element P32KA00ESC
Activated carbon adsorber filter element P32KA00ESA
Use 10mm L-Bracket (fits to body) P32KA00ML
or 3/8" Flex
4.8 mm (.19) Bowl
Tubing
T-Bracket (fits to body connector) P32KA00MB
I.D. Tube removal
Barb fitting
41 clearance. T-Bracket with body connector P32KA00MT
(1.6)
(Manual and
Auto Drain.) Body connector P32KA00CB
Manual Drain Automatic Drain Differential pressure indicator (replacement) P32KA00RQ

Parker Hannifin Corporation

Pneumatic Division - Asia
27
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Standard Coalescing and Adsorber Filter - P33

• Integral 1/2" or 3/4" ports (NPT, BSPP & BSPT)
• Removes liquid aerosols and sub micron particles
• Oil free air for critical applications, such as air gauging,
pneumatic instrumentation and control
• Differential Pressure Indicator (DPI) standard on
Coalescing Filters
• Positive bayonet latch to ensure correct & safe fitting
• Adsorbing activated carbon element removes oil vapors and
most hydrocarbons

Note: To optimize the life of coalescing element, it is

advisable to install a P33F pre-filter with a 5 micron
element upstream of the coalescing filter.
To optimize the life of an Adsorber it is advisable
to install a P33 Coalescing Filter upstream of the
Adsorber. Adsorber element should be replaced
Options: approximately every 1000 hours of service.

P33 FA N

Thread type Port size Bowl type Mounting

BSPP 1 1/2 4 Poly bowl with bowl guard G No bracket N
BSPT 2 3/4 6 Metal bowl without sight gauge M
NPT 9 Metal bowl with sight gauge S

Element Drain type

0.01µ Element C Manual drain M
0.01µ Element with dpi D Auto drain A
1µ Element 9
1µ Element with dpi Q
Adsorber A

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/2" Poly bowl - 0.01 Micron, Manual drain P33FA24DGMN 20 (42) 10 (150) 235 (9.3) 73 (2.9) 73 (2.9)

1/2" Poly bowl - 0.01 Micron, Auto drain P33FA24DGAN 20 (42) 10 (150) 229 (9.0) 73 (2.9) 73 (2.9)

1/2" Metal bowl - 0.01 Micron, Manual drain P33FA24DSMN 20 (42) 17 (250) 235 (9.3) 73 (2.9) 73 (2.9)

1/2" Metal bowl - 0.01 Micron, Auto drain P33FA24DSAN 20 (42) 17 (250) 229 (9.0) 73 (2.9) 73 (2.9)

3/4" Poly bowl - 0.01 Micron, Manual drain P33FA26DGMN 20 (42) 10 (150) 235 (9.3) 73 (2.9) 73 (2.9)

3/4" Poly bowl - 0.01 Micron, Auto drain P33FA26DGAN 20 (42) 10 (150) 229 (9.0) 73 (2.9) 73 (2.9)

3/4" Metal bowl - 0.01 Micron, Manual drain P33FA26DSMN 20 (42) 17 (250) 235 (9.3) 73 (2.9) 73 (2.9)

3/4" Metal bowl - 0.01 Micron, Auto drain P33FA26DSAN 20 (42) 17 (250) 229 (9.0) 73 (2.9) 73 (2.9)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.2 (3 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options
chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
28
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Specifications Flow Charts

Flow Capacity dm3/s SCFM P33 - 1.0 micron flow
1.0 Micron Coalescing Energy Efficient Flow* 32 (68) Primary Pressure - bar 2.0 4.0 6.3
Primary Pressure - psig 29 58 91.4
Maximum Flow** 44 (93) 7 0.5
0.01 Micron Coalescing Energy Efficient Flow* 20 (42) 6 0.4

Pressure Drop - (psig)

Maximum Flow** 34 (72)

Pressure Drop - bar

5
Activated Carbon Adsorber Rated Flow* 44 (93) 4
0.3

Max. Operating Plastic Bowl 52°C (125°F) 3 0.2

Temperature Metal Bowl 65.5°C (150°F) 2 Saturated
Element
Max. Supply Plastic Bowl 10 bar (150 psig) 1
0.1
Flow
Pressure Metal Bowl 17 bar (250 psig) 0 0
0 10 20 30 40 50
Standard Filtration 1.0 and 0.01 Micron Flow - dm3/s

ppm wt 0 20 40 60
Flow - (scfm)
80 100

Adsorber Max. oil carryover (ppm w/w) 0.003 @ 21OC (70OF)

Useful Retention† 85 cm3 (2.8 US oz.) P33 - 0.01 micron flow
Port Size BSPP / BSPT / NPT 1/2, 3/4
Primary Pressure - bar 2.0 4.0 6.3
Weight 0.50 kg (1.10 lbs) 0.5
Primary Pressure - psig 29 58 91.4
7
* Inlet pressure 6.3 bar (91.3 psig), Pressure drop 0.2 bar (3 psig),
6 0.4
Saturated Element.

Pressure Drop - (psig)

Pressure Drop - bar

** Inlet pressure 6.3 bar (91.3 psig), Pressure drop 0.4 bar (6 psig), 5
0.3
Saturated Element. 4
†
Useful retention refers to volume below the quiet zone baffle. 3 0.2
2 Saturated
0.1 Element
1 Flow
0 0
0 10 20 30 40
Flow - dm3/s
0 20 40 60 80
Flow - (scfm)

Dimensions Materials of Construction

Body Aluminum
Body Cap ABS
73 73
(2.9) (2.9) Bowls Plastic Bowl Polycarbonate
36 Metal Bowl Zinc
DPI (1.4)
Filter Element 1.0 and .01 Micron Borosilicate Cloth
Adsorber Activated Carbon
48 Seals Nitrile
(1.9)
Sight Gauge Metal Bowl Polycarbonate

Repair and Service Kits

235 Plastic bowl / Bowl guard manual drain P33KA00BGM
(9.3)
Metal bowl / Sight gauge manual drain P33KA00BSM
Auto drain P32KA00DA
1µ coalescing filter element P33KA00ES9
0.01µ coalescing filter element P33KA00ESC
Activated carbon adsorber filter element P33KA00ESA
Use 10mm L-Bracket (fits to body) P33KA00ML
4.8 mm (.19) Bowl or 3/8" Flex
removal Tubing
T-Bracket (fits to body connector) P32KA00MB
I.D. Tube
51 clearance.
Barb fitting (2.0) T-Bracket with body connector P32KA00MT
(Manual and
Auto Drain.) Body connector P32KA00CB
Manual Drain Automatic Drain Differential pressure indicator (replacement) P32KA00RQ

Parker Hannifin Corporation

Pneumatic Division - Asia
29
1002-1/Asia Dec 2010
P31 Series
Parker One Pneumatic

Mini Regulator - P31 Symbols

3 1 2
1 2

Self relieving regulator Non relieving regulator

with gauge

• Integral 1/4" ports (NPT, BSPP & BSPT)

• Robust but lightweight aluminum construction
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig)
• Secondary aspiration plus balanced poppet provides quick
response and accurate pressure regulation.
• Relieving & Non-relieving types
• Non-rising knob
Options:

P31 RA N P

Thread type Port size Mounting

BSPP 1 1/4 2 Plastic panel mount nut P
BSPT 2
NPT 9

Relief Adjustment range

Relieving B With square gauge With round gauge Without guage
Non relieving N 2 bar (0.2 MPa)* 2 2 bar (0.2 MPa) Z 2 bar (0.2 MPa) Y
Reverse flow / relieving R
4 bar (0.4 MPa)* 4 4 bar (0.4 MPa) M 4 bar (0.4 MPa) L
8 bar (0.8 MPa)** 6 8 bar (0.8 MPa) G 8 bar (0.8 MPa) N

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" 8 bar (125 psig) relieving P31RA22BNNP 30 (64) 20 (300) 100.1 (3.94) 40 (1.58) 40 (1.58)

1/4" 8 bar (125 psig) + gauge P31RA22BN6P 30 (64) 20 (300) 100.1 (3.94) 40 (1.58) 64.3 (2.53)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
30
1002-1/Asia Dec 2010
P31 Series
Parker One Pneumatic

Specifications Flow Charts

Flow Capacity* 1/4 30 dm3/s (64 scfm) 1/4 Regulator
Inlet Pressure - 10 bar (145 psig)
Max. Operating Temperature 65.5°C (150°F) 140
10

Max. Supply Pressure 20 bar (300 psig) 120

9

Secondary Pressure - (psig)

8

Secondary Pressure - bar

Adjusting Range Pressure 0-2 bar (30 psig) 100 7
8.0 bar
116 psig
0-4 bar (60 psig) 80
6
6.3 bar
5
0-8 bar (125 psig) 60 4
91.4 psig

Port Size BSPP / BSPT / NPT 1/4 40 3

4.0 bar
Gauge Port (2 ea.)** BSPP / BSPT / NPT 1/8 20
2
2.5 bar 58 psig
1 36.3 psig
Weight 0.17 kg (0.37 lbs) 0 0
0 5 10 15 20 25 30 35 40
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig). Flow - dm3/s
** Non-gauge option only. 0 10 20 30 40 50 60 70 80
Flow - (scfm)
Materials of Construction
Body Aluminum
Adjustment Knob Acetal
Body Cap ABS
Bonnet PBT
Diaphragm Assembly Brass / Nitrile
Bottom Plug 33% Glass-Filled Nylon
Valve Assembly Brass / Nitrile
Springs Steel
Seals Nitrile
Panel Nut Acetal Repair and Service Kits
Regulator repair kit - Relieving P31KA00RB
Regulator repair kit - Non-relieving P31KA00RC
Panel mount nut - Aluminum P31KA00MM
Panel mount nut - Plastic P31KA00MP
Dimensions
Angle Bracket (uses panel mount threads) P31KA00MR
64
40 (2.53) C-Bracket (fits to body) P31KA00MW
37
(1.58) (1.46) T-Bracket with body connector P31KA00MT

34.1 Body connector P31KA00CB

(1.34)
61
(2.4)
100.1
(3.94)

Gauges
Square flush mount gauge
0-4 bar K4511SCR04B
NOTE: 31.7 mm (1.25 in.) hole required for panel nut mounting.
0-10 bar K4511SCR11B
! WARNING 0-60 psig K4511SCR060
Product rupture can cause serious injury. 0-150 psig K4511SCR150
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating. 0-0.4 Mpa K45SCR04M

CAUTION: 0-1.1 Mpa K45SCR11M

REGULATOR PRESSURE ADJUSTMENT – The working range of knob 40mm Round 1/8" center back mount
adjustment is designed to permit outlet pressures within their full range. (Not for use with Common Port Regulators)
Pressure adjustment beyond this range is also possible because the knob
is not a limiting device. This is a common characteristic of most industrial 0-2 bar (0-0.2 Mpa) K4515R1402B
regulators, and limiting devices may be obtained only by special design. For
best performance, regulated pressure should always be set by increasing 0-4 bar (0-0.4 Mpa) K4515R1404B
the pressure up to the desired setting. 0-8 bar (0-0.8 Mpa) K4515R1411B
For best performance, regulated pressure should always be set by increasing the
pressure up to the desired setting.

Parker Hannifin Corporation

Pneumatic Division - Asia
31
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Mini Common - P1 Regulator - P31 Symbols

P2
P2
P2 3 1 2
P2 P1 1 2

Self relieving regulator Non relieving regulator

with gauge
P1
• Manifold style regulator with line pressure on both sides.
• Pressure output is at front or rear.
• Integral 1/4" ports (NPT, BSPP & BSPT)
• Robust construction
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig)
• Secondary aspiration plus balanced poppet provides quick
response and accurate pressure regulation
• Relieving & Non-relieving types
P1
• Non-rising knob

P2 P2 P2 P2
Options:

P31 HA N P

Thread type Port size Mounting

BSPP 1 1/4 2 Plastic panel mount nut P
BSPT 2
NPT 9 Adjustment range
Relief
Relieving B Without gauge
2 bar; 30 psig Y
Non relieving N
4 bar; 60 psig L
8 bar; 125 ps N
Order gauges separately - see next page.

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" 8 bar (125 psig) Relieving P31HA22BNNP 18 (38) 20 (300) 100.1 (3.94) 40 (1.58) 40 (1.58)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
32
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Specifications Flow Charts

Flow Capacity* 1/4 18 dm3/s (38 scfm) 1/4 Common Regulator
Max. Operating Temperature 65.5°C (150°F) Inlet Pressure - 10 bar (145 psig)
7
Max. Supply Pressure 20 bar (300 psig) 100

Adjusting Range Pressure 0-2 bar (30 psig) 6

Secondary Pressure - (psig)

Secondary Pressure - bar

80
0-4 bar (60 psig) 5
60
0-8 bar (125 psig) 4 8.0 bar
116 psig
P1 Port Size (Inlet / Outlet) BSPP / BSPT / NPT 1/4 40
3
6.3 bar
P2 Regulated Ports (2 ea.) BSPP / BSPT / NPT 1/8 2 4.0 bar 91.4 psig
20 58 psig
Weight 0.30 kg (0.66 lbs) 1 2.5 bar
36.3 psig
0 0
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig). 0 5 10 15 20 25 30 35 40
Flow - dm3/s
0 10 20 30 40 50 60 70 80
Materials of Construction Flow - (scfm)

Body Zinc
Adjustment Knob Acetal
Body Cap ABS
Bonnet 33% Glass-filled PBT
Diaphragm Assembly Brass / Nitrile
Bottom Plug 33% Glass-filled Nylon
Valve Assembly Brass / Nitrile

Dimensions Repair and Service Kits

40
Regulator repair kit - Relieving P31KA00RB
40 (1.58) Regulator repair kit - Non-relieving P31KA00RC
20
(1.58)
(0.79)
Panel mount nut - Aluminum P31KA00MM
34.1 Panel mount nut - Plastic P31KA00MP
(1.34)
Angle Bracket (uses panel mount threads) P31KA00MR
61
(2.4) T-Bracket with body connector P31KA00MT
100.1 Body connector P31KA00CB
(3.94)

Gauges
1.25" Round 1/8" center back mount
0-60 psig / 0-4 bar K4513N18060
0-160 psig / 0-11 bar K4513N18160
NOTE: 31.7 mm (1.25 in.) hole required for panel nut mounting.
For best performance, regulated pressure should always be set by increasing the
pressure up to the desired setting.
! WARNING
Product rupture can cause serious injury.
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating.

CAUTION:
REGULATOR PRESSURE ADJUSTMENT – The working range of knob
adjustment is designed to permit outlet pressures within their full range.
Pressure adjustment beyond this range is also possible because the knob
is not a limiting device. This is a common characteristic of most industrial
regulators, and limiting devices may be obtained only by special design. For
best performance, regulated pressure should always be set by increasing
the pressure up to the desired setting.

Parker Hannifin Corporation

Pneumatic Division - Asia
33
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Compact Regulator – P32 Symbols

3 1 2
1 2

Self relieving regulator Non relieving regulator

with gauge

• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)

• Robust but lightweight aluminum construction
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig), 0-17 bar (0-250 psig)
• Secondary aspiration plus balanced poppet provides quick
response and accurate pressure regulation
• Relieving & Non-relieving types
• Non-rising knob
Options:

P32 RA N P

Thread type Port size Mounting

BSPP 1 1/4 2 Plastic panel mount nut P
BSPT 2 3/8 3
NPT 9 1/2 4 Adjustment range
With round gauge
Relief
2 bar; 30 psig; 0.2 MPa Z
Relieving B
4 bar; 60 psig; 0.4 MPa M
Non relieving N
8 bar; 125 psig; 0.8 MPa G
Reverse flow / relieving R
17 bar; 250 psig; 1.7 MPa J
Without gauge
2 bar; 30 psig; 0.2 MPa Y
4 bar; 60 psig; 0.4 MPa L
8 bar; 125 psig; 0.8 MPa N
17 bar; 250 psig; 1.7 MPa H

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" 8 bar (125 psig) Relieving P32RA22BNNP 41 (81) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

1/4" 8 bar (125 psig) Relieving + Gauge P32RA22BNGP 41 (81) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

3/8" 8 bar (125 psig) Relieving P32RA23BNNP 65 (138) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

3/8" 8 bar (125 psig) Relieving + Gauge P32RA23BNGP 65 (138) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

1/2" 8 bar (125 psig) Relieving P32RA24BNNP 67 (142) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

1/2" 8 bar (125 psig) Relieving + Gauge P32RA24BNGP 67 (142) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
34
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Specifications Flow Charts

Flow Capacity* 1/4 41 dm3/s (81 scfm) 1/4 Regulator
Inlet Pressure - 10 bar (145 psig)
3/8 65 dm3/s (138 scfm) 140
10
9
1/2 67 dm3/s (142 scfm) 120

Secondary Pressure - (psig)

8

Secondary Pressure - bar

Max. Operating Temperature 65.5°C (150°F) 100 7
8.0 bar
6
Max. Supply Pressure 20 bar (300 psig) 80
5
116 psig

Adjusting Range Pressure 0-2 bar (30 psig) 60 4

6.3 bar
3
0-4 bar (60 psig) 40 91.4 psig
2
4.0 bar
0-8 bar (125 psig) 20
1
2.5 bar
36.3 psig 58 psig
0-17 bar (250 psig) 0 0
0 10 20 30 40 50 60 70
Flow - dm3/s
Port Size BSPP / BSPT / NPT 1/4, 3/8, 1/2
0 20 40 60 80 100 120 140
Gauge Port (2 ea.) BSPP / BSPT / NPT 1/4 Flow - (scfm)

Weight 0.41 kg (0.90 lbs) 3/8 Regulator

Inlet Pressure - 10 bar (145 psig)
10
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig). 140
9
120

Secondary Pressure - (psig)

Materials of Construction 8

Secondary Pressure - bar

100 7
8.0 bar
6
Body Aluminum 80
5 6.3 bar
116 psig
91.4 psig
Adjustment Knob Acetal 60 4
4.0 bar
3 58 psig
Body Cap ABS 40
2
20 2.5 bar
Bonnet 33% Glass-filled nylon 1 36.3 psig
0 0
Diaphragm Assembly Nitrile / Zinc 0 10 20 30 40 50 60 70 80
Flow - dm3/s
Bottom Plug 33% Glass-filled Nylon 0 20 40 60 80 100 120 140 160
Valve Assembly Brass / Nitrile Flow - (scfm)

Springs Main Regulating Valve Steel S.S. 1/2 Regulator

Inlet Pressure - 10 bar (145 psig)
Seals Nitrile 140
10
9
Panel Nut Acetal 120
Secondary Pressure - (psig)

8
Secondary Pressure - bar

100 7
8.0 bar
6 116 psig
80
5 6.3 bar
60 91.4 psig
Dimensions 40
4
3
4.0 bar
94 2
2.5 bar 58 psig
20
60 (3.74) 1 36.3 psig
65
0 0
(2.36) (2.57) 0 10 20 30 40 50 60 70 80 90
Flow - dm3/s
0 20 40 60 80 100 120 140 160 180
Flow - (scfm)
78.7
(3.1)

93
Repair and Service Kits
136
(3.66)
(5.4) Regulator repair kit - Relieving P32KA00RB
Regulator repair kit - Non-relieving P32KA00RC
Panel mount nut - Aluminum P32KA00MM
Panel mount nut - Plastic P32KA00MP
Angle Bracket (uses panel mount threads) P32KA00MR
30 60
(1.2) (2.36) T-Bracket with body connector P32KA00MT
NOTE: 51 mm (2.00 in.)hole required for panel nut mounting. T-Bracket P32KA00MB
Body connector P32KA00CB
! WARNING
Product rupture can cause serious injury. Gauges
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating. 50mm (2") Round 1/4" center back mount
0-2 bar / 0-0.2 Mpa / 0-30 psig K4520R1402B
CAUTION: 0-4 bar / 0-0.4 Mpa / 0-60 psig K4520R1404B
REGULATOR PRESSURE ADJUSTMENT – The working range of knob 0-11 bar / 0-1.1 Mpa / 0-160 psig K4520R1411B
adjustment is designed to permit outlet pressures within their full range.
Pressure adjustment beyond this range is also possible because the knob 0-20 bar / 0-2 Mpa / 0-300 psig K4520R1420B
is not a limiting device. This is a common characteristic of most industrial
For best performance, regulated pressure should always be set by increasing the
regulators, and limiting devices may be obtained only by special design. For pressure up to the desired setting.
best performance, regulated pressure should always be set by increasing
the pressure up to the desired setting.

Parker Hannifin Corporation

Pneumatic Division - Asia
35
1002-1/Asia Dec 2010
P32 Series
Parker One Pneumatic

Compact Common P1 Regulator - P32 Symbols

3 1 2
1 2

P2
P1 Self relieving regulator Non relieving regulator
with gauge

P1 • Manifold style regulator with line pressure on both sides.

• Pressure output is at front or rear.
• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)
• Robust construction
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig), 0-17 bar (0-250 psig)
• Secondary aspiration plus balanced poppet provides quick
response and accurate pressure regulation

P1
• Relieving & Non-relieving types
• Non-rising knob

P2 P2 P2 P2
Options:

P32 HA N P

Thread type Port size Mounting

BSPP 1 1/4 2 Plastic panel mount nut P
BSPT 2 3/8 3
NPT 9 1/2 4 Adjustment range
Without gauge
Relief
2 bar; 30 psig; 0.2 MPa Y
Relieving B 4 bar; 60 psig; 0.4 MPa L
Non relieving N 8 bar; 125 psig; 0.8 MPa N
17 bar; 250 psig; 1.7 MPa H
Order gauges separately- see next page.

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" 8 bar (125 psig) Relieving P32HA22BNNP 28 (59) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

3/8" 8 bar (125 psig) Relieving P32HA23BNNP 28 (59) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

1/2" 8 bar (125 psig) Relieving P32HA24BNNP 28 (59) 20 (300) 136 (5.4) 60 (2.36) 60 (2.36)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
36
1002-1/Asia Dec 2010
P32 Series
Parker One Pneumatic

Specifications Flow Charts

Flow Capacity* 1/4 28 dm3/s (59 scfm) P32 Common Port Regulator
3/8 28 dm3/s (59 scfm)
Inlet Pressure - 10 bar (145 psig)
1/2 28 dm3/s (59 scfm) 100 7

Max. Operating Temperature 65.5°C (150°F) 6

Secondary Pressure - (psig)

Secondary Pressure - bar

80
Max. Supply Pressure 20 bar (300 psig) 5

Adjusting Range Pressure 0-2 bar (30 psig) 60 4

0-4 bar (60 psig) 40

3 8.0 bar
116 psig
0-8 bar (125 psig) 2 6.3 bar
20 91.4 psig
4.0 bar
0-17 bar (250 psig) 1 2.5 bar 58 psig
36.3 psig
Port Size BSPP / BSPT / NPT 1/4, 3/8, 1/2 0 0
0 10 20 30 40 50 60
Gauge Port (2 ea.) BSPP / BSPT / NPT 1/4 Flow - dm3/s
0 20 40 60 80 100 120
Weight 0.50 kg (1.10 lbs) Flow - (scfm)

* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig).

Materials of Construction
Body Zinc
Adjustment Knob Acetal
Body Cap ABS
Bonnet 33% Glass-filled nylon
Diaphragm Assembly Nitrile / Zinc
Bottom Plug 33% Glass-filled Nylon
Valve Assembly Brass / Nitrile
Springs Main Regulating Steel
Valve S.S.
Seals Nitrile
Panel Nut Acetal

Dimensions Repair and Service Kits

94 Regulator repair kit - Relieving P32KA00RB
60 65 (3.74) Regulator repair kit - Non-relieving P32KA00RC
(2.36) (2.57)
Panel mount nut - Aluminum P32KA00MM
Panel mount nut - Plastic P32KA00MP
78.7 Angle Bracket (uses panel mount threads) P32KA00MR
(3.1)
T-Bracket with body connector P32KA00MT
136 T-Bracket P32KA00MB
(5.4)
93 Body connector P32KA00CB
(3.66)

Gauges
30 60 50mm (2") Round 1/4" center back mount
(1.2) (2.36)
NOTE: 51 mm (2.00 in.)hole required for panel nut mounting.
0-2 bar / 0-0.2 Mpa / 0-30 psig K4520R1402B
0-4 bar / 0-0.4 Mpa / 0-60 psig K4520R1404B
! WARNING 0-11 bar / 0-1.1 Mpa / 0-160 psig K4520R1411B
Product rupture can cause serious injury. 0-20 bar / 0-2 Mpa / 0-300 psig K4520R1420B
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating. For best performance, regulated pressure should always be set by increasing the
pressure up to the desired setting.
CAUTION:
REGULATOR PRESSURE ADJUSTMENT – The working range of knob
adjustment is designed to permit outlet pressures within their full range.
Pressure adjustment beyond this range is also possible because the knob
is not a limiting device. This is a common characteristic of most industrial
regulators, and limiting devices may be obtained only by special design. For
best performance, regulated pressure should always be set by increasing
the pressure up to the desired setting.

Parker Hannifin Corporation

Pneumatic Division - Asia
37
1002-1/Asia Dec 2010
Parker One Pneumatic

Standard Regulator - P33 Symbols

3 1 2
1 2

Self relieving regulator Non relieving regulator

with gauge

• Integral 1/2" or 3/4" ports (NPT, BSPP & BSPT)

• Robust but lightweight aluminum construction
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig), 0-17 bar (0-250 psig)
• Secondary aspiration plus balanced poppet provides quick
response and accurate pressure regulation
• Relieving & Non-relieving types
• Non-rising knob
Options:

P33 RA N P

Thread type Port size Mounting

BSPP 1 1/2 4 Plastic panel mount nut P
BSPT 2 3/4 6
NPT 9 Adjustment range
With round gauge
Relief
2 bar; 30 psig; 0.2 MPa Z
Relieving B
4 bar; 60 psig; 0.4 MPa M
Non relieving N
8 bar; 125 psig; 0.8 MPa G
Reverse flow / relieving R
17 bar; 250 psig; 1.7 MPa J
Without gauge
2 bar; 30 psig; 0.2 MPa Y
4 bar; 60 psig; 0.4 MPa L
8 bar; 125 psig; 0.8 MPa N
17 bar; 250 psig; 1.7 MPa H

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/2" 8 bar (125 psig) Relieving P33RA24BNNP 100 (212) 20 (300) 149 (5.9) 73 (2.9) 73 (2.9)

1/2" 8 bar (125 psig) Relieving + Gauge P33RA24BNGP 100 (212) 20 (300) 149 (5.9) 73 (2.9) 73 (2.9)

3/4" 8 bar (125 psig) Relieving P33RA26BNNP 100 (212) 20 (300) 149 (5.9) 73 (2.9) 73 (2.9)

3/4" 8 bar (125 psig) Relieving + Gauge P33RA26BNGP 100 (212) 20 (300) 149 (5.9) 73 (2.9) 73 (2.9)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
38
1002-1/Asia Dec 2010
Parker One Pneumatic

Specifications Flow Charts

Flow Capacity* 1/2 100 dm3/s (212 scfm) 1/2 Regulator
3/4 100 dm3/s (212 scfm) 10
Inlet Pressure - 10 bar (145 psig)
140
Max. Operating Temperature 65.5°C (150°F) 9
120

Secondary Pressure - (psig)

8

Secondary Pressure - bar

Max. Supply Pressure 20 bar (300 psig) 100 7 8.0 bar
116 psig
Adjusting Range Pressure 0-2 bar (30 psig) 80
6
6.3 bar
0-4 bar (60 psig) 60
5 91.4 psig
4
0-8 bar (125 psig) 40 3
0-17 bar (250 psig) 20
2
2.5 bar 4.0 bar
1 36.3 psig 58 psig
Port Size BSPP / BSPT / NPT 1/2, 3/4 0 0
Gauge Port (2 ea.) BSPP / BSPT / NPT 1/4 0 20 40 60 80
Flow - dm3/s
100 120 140

Weight 0.62 kg (1.37 lbs) 0 40 80 120 160 200 240 280

Flow - (scfm)
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig).
3/4 Regulator
Inlet Pressure - 10 bar (145 psig)
10
Materials of Construction 140
9
120

Secondary Pressure - (psig)

8

Secondary Pressure - bar

Body Aluminum 100 7 8.0 bar
116 psig
6
Adjustment Knob Acetal 80
5
Body Cap ABS 60 4
6.3 bar
91.4 psig
Bonnet 33% Glass-filled Nylon 40 3
2 4.0 bar
Diaphragm Assembly Nitrile / Zinc 20
1 2.5 bar
58 psig
36.3 psig
Valve Assembly Brass / Nitrile / Acetal 0 0
0 20 40 60 80 100 120 140 160
Flow - dm3/s
Springs Main Regulating Steel
Valve S.S. 0 40 80 120 160 200
Flow - (scfm)
240 280 300 340

Seals Nitrile
Panel Nut Acetal Repair and Service Kits
Dimensions Regulator repair kit - Relieving P33KA00RB
108
(4.27) Regulator repair kit - Non-relieving P33KA00RC
72
(2.83) Panel mount nut - Aluminum P33KA00MM
Panel mount nut - Plastic P33KA00MP
83.8 Angle Bracket (uses panel mount threads) P33KA00MR
(3.3) T-Bracket with body connector P32KA00MT
149 T-Bracket P32KA00MB
(5.9)
Body connector P32KA00CB
105
(4.16)
Gauges
50mm (2") Round 1/4" center back mount
37
(1.44) 73
73 0-2 bar / 0-0.2 Mpa / 0-30 psig K4520R1402B
(2.9)
(2.9) 0-4 bar / 0-0.4 Mpa / 0-60 psig K4520R1404B
NOTE: 61 mm (2.40 in.) hole required for panel nut mounting. 0-11 bar / 0-1.1 Mpa / 0-160 psig K4520R1411B
! WARNING 0-20 bar / 0-2 Mpa / 0-300 psig K4520R1420B

Product rupture can cause serious injury. For best performance, regulated pressure should always be set by increasing the
Do not connect regulator to bottled gas. pressure up to the desired setting.
Do not exceed Maximum primary pressure rating.

CAUTION:
REGULATOR PRESSURE ADJUSTMENT – The working range of knob
adjustment is designed to permit outlet pressures within their full range.
Pressure adjustment beyond this range is also possible because the knob
is not a limiting device. This is a common characteristic of most industrial
regulators, and limiting devices may be obtained only by special design. For
best performance, regulated pressure should always be set by increasing
the pressure up to the desired setting.

Parker Hannifin Corporation

Pneumatic Division - Asia
39
1002-1/Asia Dec 2010
P31 Series
Parker One Pneumatic

Mini Filter / Regulator - P31 Symbols

1 2

• Integral 1/4" ports (NPT, BSPP & BSPT)

• High efficiency 5 micron element as standard
• Excellent water removal efficiency
• Robust but lightweight aluminum construction
• Positive bayonet latch to ensure correct & safe fitting
Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig)
• Secondary aspiration plus balanced poppet provides quick
Options: response and accurate pressure regulation

P31 EA E N P

Thread type Drain type Mounting

BSPP 1 Pulse drain B Plastic panel P
mount nut
BSPT 2 Manual drain M
NPT 9

Port size Relief Adjustment range

1/8 1
1/4 2
Relieving B With square gauge With round gauge Without guage
Non relieving N
2 bar (0.2 MPa)* 2 2 bar (0.2 MPa) Z 2 bar (0.2 MPa) Y
Element
4 bar (0.4 MPa)* 4 4 bar (0.4 MPa) M 4 bar (0.4 MPa) L
5µ Element E
8 bar (0.8 MPa)** 6 8 bar (0.8 MPa) G 8 bar (0.8 MPa) N
Bowl type
Poly bowl with bowl guard G
Metal bowl without sight gauge M

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" 8 bar (125 psig) Relieving - Poly bowl - Manual drain P31EA22EGMBN6P 14 (30) 10 (150) 164.1 (6.46) 40 (1.58) 64 (2.53)

1/4" 8 bar (125 psig) Relieving - Poly bowl - Pulse drain P31EA22EGBBN6P 14 (30) 10 (150) 164.1 (6.46) 40 (1.58) 64 (2.53)

1/4" 8 bar (125 psig) Relieving - Metal bowl - Manual drain P31EA22EMMBN6P 14 (30) 17 (250) 164.1 (6.46) 40 (1.58) 64 (2.53)

1/4" 8 bar (125 psig) Relieving - Metal bowl - Pulse drain P31EA22EMBBN6P 14 (30) 17 (250) 164.1 (6.46) 40 (1.58) 64 (2.53)
* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
40
1002-1/Asia Dec 2010
P31 Series
Parker One Pneumatic

Specifications Flow Charts

Flow Capacity* 1/4 14 dm3/s (30.0 scfm) 1/4 Filter/Regulator
Max. Operating Plastic Bowl 52°C (125°F) 10
Inlet Pressure - 10 bar (145 psig)
140
Temperature Metal Bowl 65.5°C (150°F) 9
120

Secondary Pressure - (psig)

8

Secondary Pressure - bar

Max. Supply Plastic Bowl 10 bar (150 psig) 100 7
Pressure Metal Bowl 17 bar (250 psig) 80
6 8.0 bar
116 psig
5
Standard Filtration 5 Micron 60 6.3 bar
4
91.4 psig
Useful Retention 12 cm3 (0.4 US oz.) 40 3
4.0 bar
Adjusting Range 0-2 bar (30 psig) 20
2
2.5 bar
58 psig
1
Pressure 0-4 bar (60 psig) 0 0
36.3 psig
5 10 15 20 25 30 35
0-8 bar (125 psig) Flow - dm3/s

Port Size BSPP / BSPT / NPT 1/4 0 10 20 30 40

Flow - (scfm)
50 60 70

Gauge Port (2 ea.)** BSPP / BSPT / NPT 1/8

Weight 0.19 kg (0.42 lbs)
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig).
** Non-gauge option only. Repair and Service Kits
Air quality:
Within ISO 8573-1: 1991 Class 3 (Particulates) Plastic bowl / Bowl guard manual drain P31KA00BGM
Within ISO 8573-1: 2001 Class 6 (Particulates)
Metal bowl / w/o sight gauge manual drain P31KA00BMM
Materials of Construction Plastic bowl / Bowl guard pulse drain P31KA00BGB
Body Aluminum Metal bowl / w/o sight gauge pulse drain P31KA00BMB
Adjustment Knob Acetal 5µ particle filter element P31KA00ESE
Body Cap ABS Regulator repair kit - Relieving P31KA00RB
Bonnet PBT
Regulator repair kit - Non-relieving P31KA00RC
Bowl Plastic Bowl Polycarbonate
Panel mount nut - Aluminum P31KA00MM
Metal Bowl Aluminum
Bowl Guard Nylon Panel mount nut - Plastic P31KA00MP
Filter Element Polyethylene Angle Bracket (uses panel mount threads) P31KA00MR
Seals Plastic Bowl Nitrile C-Bracket (fits to body) P31KA00MW
Metal Bowl Nitrile T-Bracket with body connector P31KA00MT
Springs Steel
Body connector P31KA00CB
Valve Assembly Brass / Nitrile
Diaphragm Assembly Brass / Nitrile
Panel Nut Acetal Gauges
For best performance, regulated pressure should always be set by increasing the
pressure up to the desired setting. Square flush mount gauge

Dimensions 0-4 bar K4511SCR04B

64
40 37
(2.53) 0-10 bar K4511SCR11B
(1.58) (1.45)
0-60 psig K4511SCR060

66
0-150 psig K4511SCR150
(2.6) 0-0.4 Mpa K45SCR04M
0-1.1 Mpa K45SCR11M
164.1 40mm Round 1/8" center back mount
Note:
(6.46) (Not for use with Common Port Regulators)
Flush-mounted gauge 0-2 bar (0-0.2 Mpa) K4515R1402B
kits will not fit units
originally purchased 0-4 bar (0-0.4 Mpa) K4515R1404B
with threaded gauge
ports. 0-8 bar (0-0.8 Mpa) K4515R1411B
4mm (5/32")
I.D. Tube Bowl For best performance, regulated pressure should always be set by increasing the
33.3
Barb fitting removal pressure up to the desired setting.
(1.31)
clear-
ance

! WARNING
Product rupture can cause serious injury.
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating.

Parker Hannifin Corporation

Pneumatic Division - Asia
41
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Compact Filter / Regulator - P32 Symbols

1 2

• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)

• High efficiency 5 micron element as standard
• Excellent water removal efficiency
• Robust but lightweight aluminum construction
• Positive bayonet latch to ensure correct & safe fitting
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig), 0-17 bar (0-250 psig)
• Secondary aspiration plus balanced poppet provides quick
Options: response and accurate pressure regulation

P32 EA E N P

Thread type Port size Drain type Mounting

BSPP 1 1/4 2 Manual drain M Plastic panel P
mount nut
BSPT 2 3/8 3 Auto drain A
NPT 9 1/2 4
Adjustment range

Element Relief With round gauge

2 bar; 30 psig; 0.2 MPa Z
5µ Element E Relieving B 4 bar; 60 psig; 0.4 MPa M
Non relieving N 8 bar; 125 psig; 0.8 MPa G
17 bar; 250 psig; 1.7 MPa J
Bowl type Without gauge
Poly bowl with bowl guard G 2 bar; 30 psig; 0.2 MPa Y
4 bar; 60 psig; 0.4 MPa L
Metal bowl without sight gauge M
8 bar; 125 psig; 0.8 MPa N
Metal bowl with sight gauge S 17 bar; 250 psig; 1.7 MPa H

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)
1/4" 8 bar (125 psig) Relieving - Poly bowl - Manual drain P32EA22EGMBNGP 42 (89) 10 (150) 254 (10.0) 60 (2.36) 60 (2.36)
1/4" 8 bar (125 psig) Relieving - Poly bowl - Auto drain P32EA22EGABNGP 42 (89) 10 (150) 248 (9.76) 60 (2.36) 60 (2.36)
1/4" 8 bar (125 psig) Relieving - Metal bowl - Manual drain P32EA22ESMBNGP 42 (89) 17 (250) 245 (9.66) 60 (2.36) 60 (2.36)
1/4" 8 bar (125 psig) Relieving - Metal bowl - Auto drain P32EA22ESABNGP 42 (89) 17 (250) 254 (10.0) 60 (2.36) 95 (3.74)
3/8" 8 bar (125 psig) Relieving - Poly bowl - Manual drain P32EA23EGMBNGP 58 (123) 10 (150) 254 (10.0) 60 (2.36) 60 (2.36)
3/8" 8 bar (125 psig) Relieving - Poly bowl - Auto drain P32EA23EGABNGP 58 (123) 10 (150) 248 (9.76) 60 (2.36) 60 (2.36)
3/8" 8 bar (125 psig) Relieving - Metal bowl - Manual drain P32EA23ESMBNGP 58 (123) 17 (250) 245 (9.66) 60 (2.36) 60 (2.36)
3/8" 8 bar (125 psig) Relieving - Metal bowl - Auto drain P32EA23ESABNGP 58 (123) 17 (250) 254 (10.0) 60 (2.36) 95 (3.74)
1/2" 8 bar (125 psig) Relieving - Poly bowl - Manual drain P32EA24EGMBNGP 64 (136) 10 (150) 245 (9.66) 60 (2.36) 95 (3.74)
1/2" 8 bar (125 psig) Relieving - Poly bowl - Auto drain P32EA24EGABNGP 64 (136) 10 (150) 248 (9.76) 60 (2.36) 95 (3.74)
1/2" 8 bar (125 psig) Relieving - Metal bowl - Manual drain P32EA24ESMBNGP 64 (136) 17 (250) 245 (9.66) 60 (2.36) 60 (2.36)
1/2" 8 bar (125 psig) Relieving - Metal bowl - Auto drain P32EA24ESABNGP 64 (136) 17 (250) 254 (10.0) 60 (2.36) 60 (2.36)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
42
1002-1/Asia Dec 2010
P32 Series
Parker One Pneumatic

Specifications Flow Charts

Flow Capacity* 1/4 42 dm /s (89 scfm)
3 1/4 Filter/Regulator
3/8 58 dm3/s (123 scfm) 140
10
Inlet Pressure - 10 bar (145 psig)

1/2 64 dm3/s (136 scfm) 120

9

Secondary Pressure - (psig)

8

Secondary Pressure - bar

Max. Operating Plastic Bowl 52°C (125°F) 100 7
8.0 bar
Temperature Metal Bowl 65.5°C (150°F) 80
6
116 psig
5
Max. Supply Plastic Bowl 10 bar (150 psig) 60 4
6.3 bar
Pressure Metal Bowl 17 bar (250 psig) 40 3
4.0 bar 91.4 psig
2 58 psig
Standard Filtration 5 Micron 20
1
2.5 bar
36.3 psig
0 0
Useful Retention† 51 cm3 (1.7 US oz.) 0 10 20 30 40 50 60 70
Flow - dm3/s
Adjusting Range 0-2 bar (30 psig) 0 20 40 60 80 100 120 140
Flow - (scfm)
Pressure 0-4 bar (60 psig)
3/8 Filter/Regulator
0-8 bar (125 psig) Inlet Pressure - 10 bar (145 psig)
10
0-17 bar (250 psig) 140
9
120

Secondary Pressure - (psig)

Port Size BSPP / BSPT / NPT 1/4, 3/8, 1/2 8

Secondary Pressure - bar

100 7
Gauge Port (2 ea.) BSPP / BSPT / NPT 1/4 6
8.0 bar
116 psig
80
Weight 0.53 kg (1.17 lbs) 5
6.3 bar
60 4
91.4 psig
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig). 40 3 4.0 bar
58 psig
†
Useful retention refers to volume below the quiet zone baffle. 2
20 2.5 bar
Air quality: 1 36.3 psig

Within ISO 8573-1: 1991 Class 3 (Particulates) 0 0

0 10 20 30 40 50 60 70 80
Within ISO 8573-1: 2001 Class 6 (Particulates) Flow - dm3/s

Materials of Construction
0 20 40 60 80 100 120 140 160
Flow - (SCFM)

Body Aluminum 1/2 Filter/Regulator

Inlet Pressure - 10 bar (145 psig)
Adjustment Knob Acetal 140
10
9
Body Cap ABS 120
Secondary Pressure - (psig)

8
Secondary Pressure - bar

Element Retainer / Baffle Acetal 100 7

8.0 bar
6 116 psig
80
Bowl Plastic Bowl Polycarbonate 5
6.3 bar
60 4
Metal Bowl Zinc 3
91.4 psig
4.0 bar
40 58 psig
Bowl Guard Nylon 2
2.5 bar
20
1 36.3 psig
Filter Element Sintered Polyethylene 0 0
0 10 20 30 40 50 60 70 80 90
Seals Plastic Bowl Nitrile Flow - dm3/s

Metal Bowl Nitrile 0 20 40 60 80 100

Flow - (scfm)
120 140 160 180

Springs Main Regulating / Valve Steel / S.S.

Repair and Service Kits
Valve Assembly Brass / Nitrile
Diaphragm Assembly Nitrile / Zinc Plastic bowl / Bowl guard manual drain P32KA00BGM
Panel Nut Acetal Metal bowl / Sight gauge manual drain P32KA00BSM
Sight Gauge Metal Bowl Polycarbonate Auto drain P32KA00DA
5µ particle filter element P32KA00ESE
Dimensions
Regulator repair kit - Relieving P32KA00RB
60
30 (2.36) 60 Regulator repair kit - Non-relieving P32KA00RC
(2.36)
(1.2) Panel mount nut - Aluminum P32KA00MM
Panel mount nut - Plastic P32KA00MP
93 Angle Bracket (fits to panel mount threads) P32KA00MR
(3.66)
T-Bracket (fits to body connector) P32KA00MB
T-Bracket with body connector P32KA00MT
Body connector P32KA00CB
254
(10.0) Gauges
50mm (2") Round 1/4" center back mount
0-2 bar / 0-0.2 Mpa / 0-30 psig K4520R1402B
Bowl
Use 10mm 0-4 bar / 0-0.4 Mpa / 0-60 psig K4520R1404B
4.8 mm (.19) or 3/8" Flex
I.D. Tube removal Tubing 0-11 bar / 0-1.1 Mpa / 0-160 psig K4520R1411B
Barb fitting clearance. 65
41 (Manual and (2.57) 0-20 bar / 0-2 Mpa / 0-300 psig K4520R1420B
Manual Drain (1.6) Auto Drain.) 95 Automatic Drain
(3.74) For best performance, regulated pressure should always be set by increasing the
pressure up to the desired setting.
! WARNING
Product rupture can cause serious injury.
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating.

Parker Hannifin Corporation

Pneumatic Division - Asia
43
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Standard Filter / Regulator - P33 Symbols

1 2

• Integral 1/2" or 3/4" ports (NPT, BSPP & BSPT)

• High efficiency 5 micron element as standard
• Excellent water removal efficiency
• Robust but lightweight aluminum construction
• Positive bayonet latch to ensure correct & safe fitting
• Secondary pressure ranges 0-2 bar (0-30 psig), 0-4 bar,
(0-60 psig), 0-8 bar (0-125 psig), 0-17 bar (0-250 psig)
• Secondary aspiration plus balanced poppet provides quick
Options: response and accurate pressure regulation

P33 EA E N P

Thread type Port size Drain type Mounting

BSPP 1 1/2 4 Manual drain M Plastic panel P
mount nut
BSPT 2 3/4 6 Auto drain A
NPT 9
Adjustment range

Element Relief With round gauge

2 bar; 30 psig; 0.2 MPa Z
5µ Element E Relieving B 4 bar; 60 psig; 0.4 MPa M
Non relieving N 8 bar; 125 psig; 0.8 MPa G
17 bar; 250 psig; 1.7 MPa J
Bowl type Without gauge
Poly bowl with bowl guard G 2 bar; 30 psig; 0.2 MPa Y
4 bar; 60 psig; 0.4 MPa L
Metal bowl without sight gauge M
8 bar; 125 psig; 0.8 MPa N
Metal bowl with sight gauge S 17 bar; 250 psig; 1.7 MPa H

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/2" 8 bar (125 psig) Relieving - Poly bowl - Manual drain P33EA24EGMBNGP 90 (191) 10 (150) 291 (11.44) 73 (2.9) 73 (2.9)

1/2" 8 bar (125 psig) Relieving - Poly bowl - Auto drain P33EA24EGABNGP 90 (191) 10 (150) 285 (11.22) 73 (2.9) 73 (2.9)

1/2" 8 bar (125 psig) Relieving - Metal bowl - Manual drain P33EA24ESMBNGP 90 (191) 17 (250) 282 (11.0) 73 (2.9) 73 (2.9)

1/2" 8 bar (125 psig) Relieving - Metal bowl - Auto drain P33EA24ESABNGP 90 (191) 17 (250) 291 (11.44) 73 (2.9) 108 (4.27)

3/4" 8 bar (125 psig) Relieving - Poly bowl - Manual drain P33EA26EGMBNGP 98 (208) 10 (150) 282 (11.0) 73 (2.9) 108 (4.27)

3/4" 8 bar (125 psig) Relieving - Poly bowl - Auto drain P33EA26EGABNGP 98 (208) 10 (150) 285 (11.22) 73 (2.9) 108 (4.27)

3/4" 8 bar (125 psig) Relieving - Metal bowl - Manual drain P33EA26ESMBNGP 98 (208) 17 (250) 291 (11.44) 73 (2.9) 73 (2.9)

3/4" 8 bar (125 psig) Relieving - Metal bowl - Auto drain P33EA26ESABNGP 98 (208) 17 (250) 282 (11.0) 73 (2.9) 73 (2.9)

* flow with 10 bar (145 psig) inlet pressure, 6.3 bar (91.3) psig) set pressure and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
44
1002-1/Asia Dec 2010
P33 Series
Parker One Pneumatic

Specifications Flow Charts

Flow Capacity* 1/2 90 dm /s (191 scfm)
3
1/2 Filter/Regulator
3/4 98 dm3/s (208 scfm) Inlet Pressure - 10 bar (145 psig)
10
140
Max. Operating Plastic Bowl 52°C (125°F) 9
120
Temperature Metal Bowl 65.5°C (150°F)

Secondary Pressure - (psig)

8

Secondary Pressure - bar

100 7
Supply Plastic Bowl 10 bar (150 psig) 6
8.0 bar
80 116 psig
Pressure Metal Bowl 17 bar (250 psig) 5
60 6.5 bar
4
Standard Filtration 5 Micron 94.3 psig 4.0 bar
40 3 58 psig
Useful Retention† 85 cm3 (2.8 US oz.) 2
20 2.5 bar
Adjusting Range 0-2 bar (30 psig) 1
36.3 psig
0 0
Pressure 0-4 bar (60 psig) 0 10 20 30 40 50 60 70 80 90 100 110 120 130
Flow - dm3/s
0-8 bar (125 psig) 0 20 40 60 80 100 120 140 160 180 200 220 240 260
Flow - (scfm)
0-17 bar (250 psig)
Port Size BSPP / BSPT / NPT 1/2, 3/4
3/4 Filter/Regulator
Gauge Port (2 ea.) BSPP / BSPT / NPT 1/4
Inlet Pressure - 10 bar (145 psig)
Weight 0.85 kg (1.87 lbs) 140
10
9
* Inlet pressure 10 bar (145 psig). Secondary pressure 6.3 bar (91.3) psig). 120

Secondary Pressure - (psig)

8

Secondary Pressure - bar

†
Useful retention refers to volume below the quiet zone baffle. 7
100 8.0 bar
Air quality: 6 116 psig
80
Within ISO 8573-1: 1991 Class 3 (Particulates) 5 6.5 bar
94.3 psig
Within ISO 8573-1: 2001 Class 6 (Particulates) 60 4
4.0 bar
40 3 58 psig
Materials of Construction 20
2
2.5 bar
1
Body Aluminum 36.3 psig
0 0
Adjustment Knob Acetal 0 10 20 30 40 50 60 70 80 90
Flow - dm3/s
100 110 120 130 140 150

Body Cap ABS 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
Flow - (scfm)
Element Retainer / Baffle Acetal
Bowls Plastic Bowl Polycarbonate
Metal Bowl Aluminum
Filter Element Sintered Polyethylene Repair and Service Kits
Seals Plastic Bowl Nitrile
Plastic bowl / Bowl guard manual drain P33KA00BGM
Metal Bowl Nitrile
Springs Main Regulating / Valve Steel / S.S. Metal bowl / Sight gauge manual drain P33KA00BSM
Valve Assembly Brass / Nitrile Auto drain P32KA00DA
Diaphragm Assembly Nitrile / Zinc 5µ particle filter element P33KA00ESE
Panel Nut Acetal Regulator repair kit - Relieving P33KA00RB
Sight Gauge Metal Bowl Polycarbonate
Regulator repair kit - Non-relieving P33KA00RC
Dimensions Panel mount nut - Aluminum P33KA00MM
73 Panel mount nut - Plastic P33KA00MP
(2.9) 73
37
(1.44) (2.9) Angle Bracket (fits to panel mount threads) P33KA00MR
T-Bracket (fits to body connector) P32KA00MB
104 T-Bracket with body connector P32KA00MT
(4.1)
Body connector P32KA00CB

291
(11.44) Gauges
50mm (2") Round 1/4" center back mount
0-2 bar / 0-0.2 Mpa / 0-30 psig K4520R1402B
0-4 bar / 0-0.4 Mpa / 0-60 psig K4520R1404B
Use 10mm
4.8 mm (.19) Bowl
or 3/8" Flex 0-11 bar / 0-1.1 Mpa / 0-160 psig K4520R1411B
I.D. Tube removal
51 Tubing 0-20 bar / 0-2 Mpa / 0-300 psig K4520R1420B
Barb fitting (2.0) clearance. 72
(Manual and (2.83)
Manual Drain 108 Automatic Drain For best performance, regulated pressure should always be set by increasing
Auto Drain.) (4.27)
the pressure up to the desired setting.
! WARNING
Product rupture can cause serious injury.
Do not connect regulator to bottled gas.
Do not exceed Maximum primary pressure rating.

Parker Hannifin Corporation

Pneumatic Division - Asia
45
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Mini Lubricator - P31 Symbols

1 2

Lubricator
with drain

• Integral 1/4" ports (NPT, BSPP & BSPT)

• Robust but lightweight aluminum construction
• Proportional oil delivery over a wide range of air flows
• Finger tip rachet control for precise oil drip rate adjustment

Options:

P31 LA L N N

Thread type Port size Bowl type Mounting

1/8 1
BSPP 1 Poly bowl with bowl guard G No bracket N
1/4 2
BSPT 2 Metal bowl without sight gauge M
NPT 9
Type Drain type
Oil mist standard sight dome L No drain; closed end N

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" Poly bowl - No drain P31LA22LGNN 13 (28) 10 (150) 147.5 (5.80) 40 (1.58) 42.7 (1.68)

1/4" Metal bowl - No drain P31LA22LMNN 13 (28) 17 (250) 147.5 (5.80) 40 (1.58) 42.7 (1.68)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.34 bar (4.9 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
46
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Specifications Flow Charts

Flow Capacity* 1/4 13 dm /s (28 scfm)
3
1/4 Lubricator
Max. Operating Plastic Bowl 52°C (125°F) Primary Pressure - bar 1.6 4.0 6.3 10
Primary Pressure - psig 23.2 58 91.4 145
Temperature Metal Bowl 65.5°C (150°F) 7 0.5
Max. Supply Plastic Bowl 10 bar (150 psig) 6 0.4

Pressure Drop - (psig)

Pressure Metal Bowl 17 bar (250 psig)

Pressure Drop - bar

5
Useful Retention 18 cm3 (0.6 US oz.) 4
0.3

Port Size BSPP / BSPT / NPT 1/4 3 0.2

Weight 0.13 kg (0.29 lbs) 2
0.1
* Inlet pressure 6.3 bar (91.3 psig). Pressure drop 0.34 bar (4.9 psig). 1

0 0
0 5 10 15 20 25
Flow - dm3/s
0 10 20 30 40 50
Materials of Construction Flow - (scfm)

Body Aluminum
Body Cap ABS
Bowl Plastic Bowl Polycarbonate
Metal Bowl Aluminum
Seals Plastic Bowl Nitrile
Metal Bowl Nitrile
Sight Dome Polycarbonate
Suggested Lubricant ISO / ASTM VG32
Pick-up Filter Sintered Bronze

Dimensions Repair and Service Kits

Plastic bowl / Bowl guard no drain P31KA00BGN
42.7
Drip control assembly P32KA00PG
(1.68)
40 21.3 Fill plug P31KA00PL
(1.58) (0.84)
C-Bracket (fits to body) P31KA00MW
T-Bracket with body connector P31KA00MT
57.2
(2.25)
Body connector P31KA00CB

147.5
(5.8)

Suggested Lubricant ............................................... F442 Oil

Petroleum based oil of 100 to 200 SUS viscosity at 38°C
Bowl (100°F) and an aniline point greater than 93°C (200°F)
12.7 removal (DO NOT USE OILS WITH ADDITIVES, COMPOUNDED
(0.5)
clearance OILS CONTAINING SOLVENTS, GRAPHITE, DETERGENTS,
OR SYNTHETIC OILS.)

Parker Hannifin Corporation

Pneumatic Division - Asia
47
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Compact Lubricator - P32 Symbols

1 2

Lubricator
with drain

• Integral 1/4", 3/8" or 1/2" ports (NPT, BSPP & BSPT)

• Robust but lightweight aluminum construction
• Proportional oil delivery over a wide range of air flows
• Finger tip rachet control for precise oil drip rate adjustment
• Fill from top under system pressure

Options:

P32 LA L N N

Thread type Port size Bowl type Mounting

BSPP 1 1/4 2 Poly bowl with bowl guard G No bracket N
BSPT 2 3/8 3 Metal bowl with sight gauge S
NPT 9 1/2 4
Drain type
Type
No drain; closed end N
Oil mist standard sight dome L

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/4" Poly bowl - No drain P32LA22LGNN 18 (38) 10 (150) 211 (8.30) 60 (2.36) 60 (2.36)

1/4" Metal bowl - No drain P32LA22LSNN 18 (38) 17 (250) 211 (8.30) 60 (2.36) 60 (2.36)

3/8" Poly bowl - No drain P32LA23LGNN 32 (68) 10 (150) 211 (8.30) 60 (2.36) 60 (2.36)

3/8" Metal bowl - No drain P32LA23LSNN 32 (68) 17 (250) 211 (8.30) 60 (2.36) 60 (2.36)

1/2" Poly bowl - No drain P32LA24LGNN 47 (100) 10 (150) 211 (8.30) 60 (2.36) 60 (2.36)

1/2" Metal bowl - No drain P32LA24LSNN 47 (100) 17 (250) 211 (8.30) 60 (2.36) 60 (2.36)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.34 bar (4.9 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
48
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Specifications Flow Charts

Flow Capacity* 1/4 18 dm3/s (38 scfm) 1/4 Lubricator
3/8 32 dm3/s (68 scfm) Primary Pressure - bar 1.6 4.0 6.3 10
Primary Pressure - psig 23.2 58 91.4 145
1/2 47 dm3/s (100 scfm) 7 0.5

Max. Operating Plastic Bowl 52°C (125°F) 6 0.4

Pressure Drop - (psig)

Pressure Drop - bar

Temperature Metal Bowl 65.5°C (150°F) 5
0.3
Max. Supply Plastic Bowl 10 bar (150 psig) 4

Pressure Metal Bowl 17 bar (250 psig) 3 0.2

2
Useful Retention 121 cm3 (4.09 US oz.) 0.1
1
Port Size BSPP / BSPT / NPT 1/4, 3/8, 1/2
0 0
Weight 0.31 kg (0.68 lbs) 0 10
Flow - dm3/s
20 30

* Inlet pressure 6.3 bar (91.3 psig). Pressure drop 0.34 bar (4.9 psig). 0 10 20 30 40 50 60
Flow - (scfm)

Materials of Construction 3/8 Lubricator

Body Aluminum Primary Pressure - bar 1.6 4.0 6.3 10
Primary Pressure - psig 23.2 58 91.4 145
Body Cap ABS 7 0.5

Bowls Plastic Bowl Polycarbonate 6 0.4

Pressure Drop - (psig)

Pressure Drop - bar

Metal Bowl Aluminum 5
0.3
4
Seals Plastic Bowl Nitrile
3 0.2
Metal Bowl Nitrile
2
Sight Dome Polycarbonate 1
0.1

Sight Gauge Metal Bowl Polycarbonate 0 0

0 10 20 30 40 50 60 70
Suggested Lubricant ISO / ASTM VG32 Flow - dm3/s
Pick-up Filter Sintered Bronze 0 20 40 60 80 100 120 140
Flow - (scfm)

1/2 Lubricator
Primary Pressure - bar 1.6 4.0 6.3 10
Primary Pressure - psig 23.2 58 91.4 145
7 0.5

6 0.4
Pressure Drop - (psig)

Pressure Drop - bar

5
0.3
4

3 0.2

Dimensions 2
0.1
1

60 0 0
0 10 20 30 40 50 60 70 80
(2.36) Flow - dm3/s
30 60
0 20 40 60 80 100 120 140 160
(1.18) (2.36) Flow - (scfm)

Repair and Service Kits

61
(2.40) Plastic bowl / Bowl guard no drain P32KA00BGN
Drip control assembly P31KA00PG
Fill plug P32KA00PL
L-Bracket (fits to body) P32KA00ML
211 T-Bracket (fits to body connector) P32KA00MB
(8.30)
T-Bracket with body connector P32KA00MT
Body connector P32KA00CB

Suggested Lubricant ............................................... F442 Oil

Petroleum based oil of 100 to 200 SUS viscosity at 38°C
(100°F) and an aniline point greater than 93°C (200°F)
Bowl (DO NOT USE OILS WITH ADDITIVES, COMPOUNDED
41 removal
(1.60)
OILS CONTAINING SOLVENTS, GRAPHITE, DETERGENTS,
clearance OR SYNTHETIC OILS.)

Parker Hannifin Corporation

Pneumatic Division - Asia
49
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Standard Lubricator - P33 Symbols

1 2

Lubricator
with drain

• Integral 1/2" or 3/4" ports (NPT, BSPP & BSPT)

• Robust but lightweight aluminum construction
• Proportional oil delivery over a wide range of air flows
• Finger tip rachet control for precise oil drip rate adjustment
• Fill from top under system pressure

Options:

P33 LA L N N

Thread type Port size Bowl type Mounting

BSPP 1 1/2 4 Poly bowl with bowl guard G No bracket N
BSPT 2 3/4 6 Metal bowl with sight gauge S
NPT 9
Drain type
Type
No drain; closed end N
Oil mist standard sight dome L

Port Flow Max. Height Width Depth

Description Order Code† 3
size dm /s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)

1/2" Poly bowl - No drain P33LA24LGNN 48 (102) 10 (150) 234 (9.21) 73 (2.9) 73 (2.9)

1/2" Metal bowl - No drain P33LA24LSNN 48 (102) 17 (250) 234 (9.21) 73 (2.9) 73 (2.9)

3/4" Poly bowl - No drain P33LA26LGNN 68 (144) 10 (150) 234 (9.21) 73 (2.9) 73 (2.9)

3/4" Metal bowl - No drain P33LA26LSNN 68 (144) 17 (250) 234 (9.21) 73 (2.9) 73 (2.9)

* flow with 6.3 bar (91.3 psig) inlet pressure and 0.34 bar (4.9 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
50
1002-1/Asia Dec 2010
Parker One Pneumatic P33 Series

Specifications Flow Charts

Flow Capacity* 1/2 48 dm3/s (102 scfm)
3/4 68 dm3/s (144 scfm) 1/2 Lubricator
Primary Pressure - bar 1.6 4.0 6.3 10
Max. Operating Plastic Bowl 52°C (125°F) Primary Pressure - psig 23.2 58 91.4 145
7 0.5
Temperature Metal Bowl 65.5°C (150°F)
6
Max. Supply Plastic Bowl 10 bar (150 psig) 0.4

Pressure Drop - (psig)

Pressure Drop - bar

5
Pressure Metal Bowl 17 bar (250 psig) 4
0.3

Useful Retention 181 cm3 (6.1 US oz.) 3 0.2

Port Size BSPP / BSPT / NPT 1/2, 3/4 2
0.1
Weight 0.47 kg (1.04 lbs) 1

* Inlet pressure 6.3 bar (91.3 psig). Pressure drop 0.34 bar (4.9 psig). 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120
Flow - dm3/s

Materials of Construction 0 20 40 60 80 100 120 140 160 180

Flow - (scfm)
200 220 240

Body Aluminum
3/4 Lubricator
Body Cap ABS Primary Pressure - bar 1.6 4.0 6.3
Bowls Plastic Bowl Polycarbonate 0.5
Primary Pressure - psig 23.2 58 91.4
7
Metal Bowl Aluminum 6 0.4

Pressure Drop - (psig)

Seals Plastic Bowl Nitrile

Pressure Drop - bar

5
Metal Bowl Nitrile 4
0.3

Sight Dome Polycarbonate 3 0.2

Sight Gauge Metal Bowl Polycarbonate 2

0.1
Suggested Lubricant ISO / ASTM VG32 1

0 0
Pick-up Filter Sintered Bronze 0 10 20 30 40 50 60 70 80 90 100 110 120
Flow - dm3/s
0 20 40 60 80 100 120 140 160 180 200 220 240
Flow - (scfm)

Dimensions Repair and Service Kits

73 Plastic bowl / Bowl guard no drain P33KA00BGN
(2.9)
36 73
(2.9)
Drip control assembly P31KA00PG
(1.44)
Fill plug P32KA00PL
L-Bracket (fits to body) P33KA00ML
51
(2.0) T-Bracket (fits to body connector) P32KA00MB
T-Bracket with body connector P32KA00MT
Body connector P32KA00CB

234
(9.21)

Suggested Lubricant ............................................... F442 Oil

Petroleum based oil of 100 to 200 SUS viscosity at 38°C
Bowl
(100°F) and an aniline point greater than 93°C (200°F)
51 (DO NOT USE OILS WITH ADDITIVES, COMPOUNDED
(2.0) removal
clearance OILS CONTAINING SOLVENTS, GRAPHITE, DETERGENTS,
OR SYNTHETIC OILS.)

Parker Hannifin Corporation

Pneumatic Division - Asia
51
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

• Very fast response times

• Accurate output pressure
• Micro parameter settings
• Selectable I/O parameters
• Quick, full flow exhaust
• LED display indicates output pressure
• No air consumption in steady state
• Multiple mounting options
• Protection to IP65
P31P Series P32P Series
Bottom exhaust Bottom exhaust • P31P flows to 19 dm3/s (40 scfm)
Order Key • P32P flows to 57 dm3/s (120 scfm)

P3 PA 1 A 2 1 A

Body size Pressure Range Output Signal

Global Mini (1/4") 1 0 - 2 bar (0-29 psig) Z Digital, PNP D
Global Compact (1/2") 2 0 - 10 bar (0-145 psig) D PNP or 0-10V P
NPN or 0-10V N
Thread type Power supply 4-20mA fixed M
BSPP 1 24 volts 2
D) Digital PNP output only, no analog
BSPT 2 output selectable
NPT 9 P) Digital PNP and analogue 0-10V
Control Signal
outputs selectable, by means of
0-10 V† V parameter 6. (Factory default 0-10V)
Port size N) Digital NPN and analog 0-10 V
† Factory setting is 0-10 V
outputs selectable by means of
Global Mini (1/4") 2 control signal. 4-20 mA
parameter 6. (Factory default 0-10V)
control signal available via
Global Compact (1/2") 4 parameter 4 on keypad. M) Analog 4-20mA output only.
Note: On all analog outputs the F.S.
value can be adjusted by means of
Version parameter 8
Bottom ported exhaust (NC) A
Input connector
Bottom ported forced exhaust (NO)* E
M12 (4 pin) 1
* When the supply voltage is lost the unit will
automatically exhaust the regulated pressure to 0 bar
(atmospheric pressure)

P31P Mounting brackets P32P Mounting brackets

Order Code Description Order Code Description
P3HKA00ML L-Bracket mounting kit P3KKA00ML L-Bracket mounting kit
P3HKA00MC Foot bracket mounting kit P3KKA00MC Foot bracket mounting kit

L-Bracket Foot Bracket L-Bracket Foot Bracket

Note:
Cables These brackets fit both Proportional
Order Code Description Regulators and Combined Soft Start
& Dump Valves.
CB-M12-4P-2M 2 mtr. cable with moulded straight M12x1 connector

Parker Hannifin Corporation

Pneumatic Division - Asia
52
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

Technical Information
Working medium Supply voltage
Compressed air or inert gasses, filtered to 40µ. 24 VDC +/- 10%

Supply pressure Power consumption

Max. Operating Pressure: Max. 1.1W with unloaded signal outputs
2 bar unit:............................ 3 bar (43.5 psig)
10 bar unit: ........................... 10.5 bar (152 psig) Control signals
Min. Operating Pressure........ P2 Pressure + 0.5 bar (7.3 psig) The electronic pressure regulator can be externally controlled
through an analogue control signal of either
Pressure control range 0-10V or 4-20mA. (parameter 4).
Available in three pressure ranges, 0-2 bar (0-29 psig), 0-7 bar
(0-101.5 psig) or 0-10 bar (0-145 psig). Pressure range can be Output signals
changed through the software at all times. As soon as the output pressure is within the signal band a
(parameter 19) signal is given of 24VDC, PNP Ri = 1 kOhm
Outside the signal band this connection is 0V.
Temperature range
0°C up to +50°C (32°F up to122°F) Connections ISO 20401
4-Pin Micro
(In case of output signal (Option D) (Top cover)

Weights: Central M12 connector 4-pole 1 4

P31P = 0.291 kg (0.64 lbs) 2 3

P32P = 0.645 kg (1.42 lbs)

BLUE
WHT
BRN

BLK
Air consumption
No consumption in stable regulated situation.
The electrical connections are as follows:
Display
The regulator is provided with a digital display, indicating the Pin No. Function Color
output pressure, either in bar or psig. 1 24 V Supply Brown
The factory setting is as indicated on the label, can be 0 to 10 V Control Signal Ri = 100k W
changed through to software at all times (parameter 14) 2 White
4 to 20mA Control Signal Ri = 500k W
3 0 V (GND) Supply Blue
4 24 V Alarm Output Signal Black

Schematic

Parker Hannifin Corporation

Pneumatic Division - Asia
53
1002-1/Asia Dec 2010
Proportional Regulators
Parker One Pneumatic

Technical information Advanced functionality

Dead band Pilot valve protection
The dead band is preset at 1.3% of Full Scale*, adjustable via When the required output pressure can not be achieved
parameter 13. because of a lack of input pressure the unit will open fully and
Accuracy will display NoP. Approximately every 10 seconds the unit will
Linearity: = < 0.3% of Full Scale.* retry. The output pressure will then be approximately equal to
Proportional band the inlet pressure. As soon as the input pressure is back on the
The proportional band is preset at 10% of Full Scale.* required level, the normal control function follows.
Fail safe operation Safety exhaust
• If the P31P / P32P unit has an “0” or “A” in the 12th digit of Should the control signal fall below 0.1 volts the valve will
the model number automatically dump downstream system pressure .
– When the supply voltage drops, the electronic control Input protection
reverts to the fail safe mode. The last known output The unit has built-in protection against failure and burnout
pressure is maintained at approximately the same resulting from incorrect input value, typically:
level depending upon air consumption. The digital The 24VDC supply is incorrectly connected to the setpoint
display indicates the last input, the display will show ‘OL’, as an overload indication. The
known pressure setting. unit will need to be rewired and when correctly connected will
– When the supply voltage is reinstated to the correct operate normally.
level, the valve moves from the fail safe mode and the The overload indicator ‘OL’ will also appear should the
output pressure immediately follows the control signal wrong input value be applied or the wrong input value
requirement. The display indicates the actual output be programmed: 4 - 20m instead of 0 - 10V. To correct
pressure. this a different set point value should be input or the unit
– Note: In the event of loss of both power and inlet reprogrammed to correct the set point value acceptance. (via
pressure the unit will exhaust downstream pressure. parameter 4).
• If the P31P / P32P unit has an “E” in the 12th digit of the
model number Response time P31P P32P
– When the supply voltage drops, the electronic control 2 to 4 bar 25 msecs 35 msecs
reverts to “Forced Exhaust Mode” and will automatically 1 to 6 bar 55 msecs 135 msecs
exhaust the downstream (regulated) pressure. 4 to 2 bar 70 msecs 85 msecs
6 to 1 bar 80 msecs 225 msecs
– When the supply voltage is reinstated to the correct level
the unit will return to normal operation and follows the To fill volume of:
control signal requirement. The display indicates the 100cm3 - P31P
actual pressure. 330cm3 - P32P
connected to the outlet of the regulator.
• If the unit has been programmed in manual mode (not with
a control signal) the unit will EXHAUST and the regulator will Settings
need to be reset when power is applied. The regulator is pre-set at the factory. If required, adjustments
can be made.
Full exhaust
Complete exhaust of the regulator is defined as Flow Charts
P2 ≤ 1% Full Scale
* Full scale (F.S.) P31P Regulator 1/4” Ports
Inlet Pressure - 10 bar (145 psig)
For 2 bar (29 psig) versions this will be 2 barr (29 psig), for the 140
10
9
10 bar (145 psig) version full scale will be 10 bar (145 psig). 120
Secondary Pressure - (psig)

8
Secondary Pressure - bar

Degree of protection 100 7

IP65 80
6
5
EU conformity 60 4
CE: standard 40 3

EMC: according to directive 89/336/EEC 20

2
1
The new pressure regulator is in accordance with: 0 0
EN 61000-6-1:2001 EN 61000-6-2:2001 5 10 15 20
Flow - dm3/s
25 30 35

EN 61000-6-3:2001 EN 61000-6-4:2001 0 10 20 30 40 50 60 70
Flow - (scfm)
These standards ensure that this unit meets the highest level of
EMC protection. P32P Regulator 1/2” Ports
Inlet Pressure - 10 bar (145 psig)
10
Mounting position 140
9
Preferably vertical, with the cable gland on top. 120
Secondary Pressure - (psig)

8
Secondary Pressure - bar

Materials: P31P & P32P 100 7

6
• Magnet Core .................................................................. Steel 80
5
• Solenoid Valve Poppet ................................................... FPM 60 4
40 3
• Solenoid Valve Housing .................................Techno Polymer 2
20
• Regulator Body (P31P & P32P versions) ................Aluminium 1
0 0
• Regulator Top Housing .................................................Nylon 0 10 20 30 40 50 60
Flow - dm3/s
70 80 90 100

• Valve Head ....................................................... Brass & NBR 0 20 40 60 80 100 120 140 160 180 200
Flow - (scfm)
• Remaining Seals ............................................................ NBR

Parker Hannifin Corporation

Pneumatic Division - Asia
54
1002-1/Asia Dec 2010
Proportional Regulators
Parker One Pneumatic

How to change parameters

Pressing the Accept key “acc” for more than 3 seconds, will When the unit is initially powered up allow approximately 10
activate parameter change mode. The user can then select seconds for the unit to “boot-up” before changing parameter
the parameters by pressing up or down key. (display will show settings.
Pxx). When parameter number is correct, pressing accept Only parameter numbers 0, 4, 6, 8, 9, 14, 18, 19, 20, 12, 13
again will enter parameter number.(display will show parameter and 21 are accessible to edit. All other parameters are fixed.
value). Manual mode:
Pressing the up or down key will change the parameter itself. When keys DOWN and UP are pressed during startup,
(display will flash indicating parameter editing mode). Pressing (connecting to the 24V power supply) manual mode is
the accept key will accept the new parameter value. (all digits activated. This means that the user is able to in/decrease the
will flash whilst being accepted). output pressure of the regulator, by pressing the UP or DOWN
After releasing all keys , the next parameter number will be key. During this action the display will blink, indicating that the
presented on the display. (you may step to the next parameter). manual mode is activated. After powering up again, the unit will
When no key is pressed, after 3 seconds the display will show revert back to normal mode.
the actual output pressure.

Back to Factory Setting

After start up. (Power is on)
Entering this value in parameter 0 will store the calibrated factory data into the working parameters.
(Default calibration data is used)

Parameter Number 0 – Reset Back to Factory Settings

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads

Flashing Decimal Flashing Decimal Flashing

Edits parameter.
3 = standard
factory settings.
Description If other than 3, Accepts and
Accesses use Up or Down saves new
changeable Accesses Displays current Arrow and parameter Sequences to
parameters. parameter no. 0. parameter value. accept 3 setting. next parameter.

Set Control Signal

The unit is factory set for 0-10 V control signal. If 4-20 mA control signal is required, change parameter 4.

Parameter Number 4 – Set Control Signal in Volts or Milliamps

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads

Flashing Decimal Flashing Decimal Flashing

Displays current Accepts and
Accesses parameter value. saves new
Description changeable Accesses 1=V parameter Sequences to
parameters. parameter no. 4. 0 = mA Edits parameter. setting. next parameter.

Parker Hannifin Corporation

Pneumatic Division - Asia
55
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

Set Output Signal

Parameter 6 is used to set the type of output signal to your PLC.
This parameter is used as follows:
Output Signal option “0” = Digital Output – PNP
• Factory set at “0” Non Adjustable
Output Signal option “P” = Digital PNP or Analog 1-10V
• Factory set at “1” for Analog Signal
• Convert to Digital PNP by changing parameter to “0” setting
Output Signal option “N” = Digital NPN or Analog 1-10V
• Factory set at “1” Analog Signal
• Convert to Digital NPN by changing parameter to “0”
Output Signal option “M” = Analog 4-20 mA
• Factory set at “2” Non Adjustable

Parameter Number 6 – Set Output Signal

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal
Flashing Decimal (Value 0, 1 or 2) Flashing
Displays current
parameter value. Edits parameter.
Description 1 = m factory 0 = digital Accepts and
Accesses default for P3H (NPN or PNP) saves new
changeable Accesses with analog 1 = analog 0..10V parameter Sequences to
parameters. parameter no. 6. options 2 = analog 4..20 mA setting. next parameter.

Adjust Span Analog Output Signal

Set value is a % of Full Analog range. As an example for a 0-10V output signal, the original factory setting of 100% will give you an adjust-
ment of 0-10V. If you reset Parameter 8 to 50%, the new output range would be 0-5V or 50% of the full range.
In the event that the output signal is to low, in a certain application, you can adjust it by increasing Parameter 8 to a maximum value of 130%
of scale.
Note that all values are nominal and that an actual measurement may be required to ensure signal strength.

Parameter Number 8 – Adjust Span Analog Output Signal

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal Flashing Decimal
(For 2 bar versions (Value between
value = 92) 0 and 130) Flashing
Accepts and
saves new
parameter
Description setting and
Accesses implements the
changeable Accesses Displays current new analog signal Sequences to
parameters. parameter no. 8. parameter value. Edits parameter. span. next parameter.

Parker Hannifin Corporation

Pneumatic Division - Asia
56
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

Adjust Digital Display

If necessary, adjustments can be made to the digital display when using an external pressure sensor.

Parameter Number 9 – Adjust Digital Display Value (Pressure Calibration)

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads

Flashing Decimal Flashing Decimal Flashing

Use up or down
arrows and
accept to adjust
Description the display Accepts and
Accesses value if using an saves new
changeable Accesses Displays current external pressure parameter Sequences to
parameters. parameter no. 9. digital display sensor. setting. next parameter.

Set Pressure Scale

Units with NPT port threads are supplied with a factory set psig pressure scale. Use parameter 14 to change scale to bar.

Parameter Number 14 – Set Pressure Scale in psig or bar

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads

Flashing Decimal Flashing Decimal Flashing

Displays current
parameter value. Accepts and
Description Accesses Accesses 1 = psig saves new
changeable parameter no. 0 = bar parameter Sequences to
parameters. 14. 2 = MPA Edits parameter. setting. next parameter.

Parker Hannifin Corporation

Pneumatic Division - Asia
57
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

Preset Minimum Pressure

If there is a need for a pre-set Minimum pressure, use parameter 18. (Note: preset pressure is affected by % P19.)

Parameter Number 18 – Set Minimum Preset Pressure

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal
(value between
Flashing Decimal 0 and 200) Flashing
Displays current
parameter value.
Incremental
value is:
Description 2 bar unit:
Accepts and
x 2 mbar x % P19
Accesses Accesses saves new
changeable parameter no. 10 bar unit: parameter Sequences to
parameters. 18. x 10 mbar x % P19 Edits parameter. setting. next parameter.

Set Pressure Correction

Pressure correction allows the user to set a Maximum pressure as a percentage of secondary pressure F.S.
Example: If F.S. is 10 bar, set parameter 19 to 50 for Maximum preset pressure of 5 bar.
Pressure correction also affects the Minimum preset pressure in parameter 18.
Example: If F.S. is 10 bar and parameter 18 is set to a value of 100 (1 bar), and parameter 19 is set to 50%, then the actual Minimum
preset pressure seen is 0.5 bar.

Parameter Number 19 – Set Maximum Preset Pressure

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal
(value between
Flashing Decimal 0 and 100) Flashing

Displays current
parameter value. Accepts and
Description Accesses Accesses Incremental saves new
changeable parameter no. value is: parameter Sequences to
parameters. 19. % of F.S. Edits parameter. setting. next parameter.

Parker Hannifin Corporation

Pneumatic Division - Asia
58
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

Behavior Control
The regulation speed of the pressure regulator can be modified by means of one parameter. (P 20)
The value in this parameter has a range from 0-5. A higher value indicates slower regulation speed, but will be more stable.

Parameter Number 20 – Set Behavior Control

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal
(value between
Flashing Decimal 0 and 5) Flashing
Edits parameter
0 = custom set*
1 = fastest
(narrow
proportional
band)
Description 2 = fast
3 = normal
4 = slow Accepts and
Accesses Accesses 5 = slowest saves new
changeable parameter no. Displays current (proportional parameter Sequences to
parameters. 20. parameter value. band is broad) setting. next parameter.

* When the value 0 is entered, you are able to create your own custom settings true parameters 12, 13 and 21.

Fine Settings
Set Proportional Band
Proportional band is used for setting the reaction sensitivity of the regulator. The displayed value is X 10 mbar and has a range between
50 (0.5 bar) and 250 (2.5 bar).

Parameter Number 12 – Set Proportional Band (P20 Must be Set to 0)

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal
(value between
Flashing Decimal 50 and 250) Flashing
Displays current
parameter value. Accepts and
Description Accesses Accesses Incremental saves new
changeable parameter no. value is: parameter Sequences to
parameters. 12. x 10 mbar Edits parameter. setting. next parameter.

Parker Hannifin Corporation

Pneumatic Division - Asia
59
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

Set Deadband
Deadband is the Minimum limit of accuracy at which the regulator is set for normal operation. The displayed value is X 10 mbar and has a range
between 4 (40 mbar) and 40 (400 mbar).

Parameter Number 13 – Set Deadband (P20 Must be Set to 0)

Step 1 2 3 4 5
Press
or or

3-6 seconds

Until Display
Reads
Flashing Decimal
(value between
Flashing Decimal 4 and 40) Flashing
Displays current
parameter value.
Description Accesses Incremental Accepts and saves
changeable Accesses value is new parameter Sequences to next
parameters. parameter no. 13. x 10 mbar Edits parameter. setting. parameter.

Proportional Effect
Parameter Number 21 – Set Proportional Effect (P20 Must be Set to
0)
Step 1 2 3 4 5
Press or or

3-6 seconds

Until Display
Reads
Flashing Decimal
(value between
Flashing Decimal 5 and 100) Flashing
Edits parameter.
5 = fastest Accepts and
Description Accesses Accesses regulation saves new
changeable parameter no. Displays current 100 = slowest parameter Sequences to
parameters. 21. parameter value. regulation. setting. next parameter.

Parameter Number 39 – Displays Current Software Version

Step 1 2 3
Press
or

3-6 seconds

Until Display
Reads

Flashing Decimal
Displays current
Accesses Accesses parameter value.
Description changeable parameter no. XXX = current
parameters. 39. software version

Parker Hannifin Corporation

Pneumatic Division - Asia
60
1002-1/Asia Dec 2010
Parker One Pneumatic Proportional Regulators

P31P P32P
4 pin M12
Connector

14.3
(0.56)

4 pin M12
Connector

14.3
(0.56)

105.3
(4.16)

175.7
(6.94)
89
(3.51)

126.25
(4.99)

64.4
(2.54)

37.25
(1.47)

75 28.6
20
(2.96) (1.13)
(0.79) 57.2
(2.26)
57 40 37.5
(2.25) (1.58) (1.48)

28.5 28.6
(1.12) (1.13)

20
(0.79)

L-Bracket L-Bracket

7
(0.28) 15
(0.59) 25 15
(0.98) (0.59) 25
(0.98)
7 30 7 30
(0.28) (1.18) (0.28) (1.18)
36 30 45
(1.42) (1.18) (1.77)
15 36 15
(0.59) (1.42) (0.59)

Foot Bracket Foot Bracket

12
(0.47)

26 56 10
(0.39) 56 12 26
(1.02) (2.20) (2.20) (0.47) (1.02)
52
(2.05) 52
(2.05)

Ø7
52 40 (0.28)
(2.05)(1.57) 52 40 Ø7
4 holes (2.05) (1.57) (0.28)
4 holes

84
(3.31) 84
100 (3.31)
(3.94) 100
Dimensions are in mm (Inches) (3.94)

Parker Hannifin Corporation

Pneumatic Division - Asia
61
1002-1/Asia Dec 2010
Parker One Pneumatic P31 / P32 Series

Combined Soft Start / Dump Valve Symbols

• Modular design with 1/4" or 1/2" integral ports

(NPT, BSPP & BSPT)
• Provides for the safe introduction of pressure
• The 3-way, 2-position function automatically dumps
downstream pressure on the loss of pilot signal
• Adjustable slow start
• Solenoid or air pilot options
• High flow & exhaust capability
• Silencer included

The controlled introduction of pressure can be an important

safety factor and prevent damage to tooling when air pressure
is introduced at machine or system start up.
Parker Global Series Combined Soft Start / Dump Valves,
provide for the safe introduction of pressure to machines or To maintain these units in the open position a pilot supply
systems. Soft Start / Dump Valves when set, allow the pressure to the air pilot operated version or an electrical signal to the
to gradually build to the set point before fully opening to deliver solenoid operated version must be maintained. The valve will
full flow at line pressure. automatically dump when the holding signal is removed.

Options:

Solenoid type only

P3 TA N

Body size Port size Pilot type 15mm (P31 series only) C 24VDC
Mini (1/4") 1 Mini (1/4") 2 External Air non locking
P 30mm CNOMO coil A 2CN
Pilot manual
Compact (1/2") 2 Compact (1/2") 4 30mm CNOMO coil overide
Solenoid Pilot S D
(M12 connection) 120VAC
Thread Type
Actuator interface non locking
BSPP (G) 1 3GN
manual
BSPT 2 15mm solenoid (P31 only) G
overide
NPT 9 30mm solenoid C
120VAC
Threaded air pilot P non locking
manual 1FN
Note: override (P31
P32 unit used for both P32 & P33 series series only)

Compact combined soft start dump valve

Port Flow Max. Height Width Depth
Description Order Code† Weight
size dm3/s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)
1/4" 120VAC Solenoid & cable plug P31TA22SGNA1FN 17 (36) 10 (150) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/4" 24VDC Solenoid & cable plug P31TA22SGNC2CN 17 (36) 10 (150) 166* (6.5) 57 (2.2) 40 (1.5) 0.41kg (0.9lbs)
1/4" External air pilot operated P31TA22PPN 17 (36) 17 (250) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/2" 120VAC 30mm coil & cable plug incl. P32TA24SCNA3GN 46 (97) 10 (150) 162.5* (6.3) 88 (3.4) 57.2 (2.2) 0.87kg (1.9lbs)
1/2" 24VDC 30mm coil & cable plug incl. P32TA24SCNA2CN 46 (97) 10 (150) 227.5* (8.9) 88 (3.4) 57.2 (2.2) 0.91kg (2.0lbs)
1/2" External air pilot operated P32TA24PPN 46 (97) 17 (250) 162.5*(6.3) 75 (2.9) 57.2 (2.2) 0.87kg (1.9lbs)

* Includes exhaust silencer. Flow with 6.3 bar (91.3) psig) inlet and 1 bar (14.5 psig) pressure drop.
† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
62
1002-1/Asia Dec 2010
Parker One Pneumatic P31 / P32 Series

Technical Information Flow characteristics

Fluid: Compressed air 1/4 Soft Start & Dump Valve
Max. pressure Solenoid operated: 10 bar (150 psig) Inlet Pressure - 6.3 bar (91.3 psig)
8
Max. pressure Air Pilot operated: 17 bar (250 psig) 9.0 bar
130.5 psig
100 7
Min. operating pressure: 3 bar (44 psig) 6.3 bar 8.0 bar

Secondary Pressure - (psig)

Secondary Pressure - bar

91.4 psig 7 bar 116 psig
6
Temperature Max.* Solenoid operated: 50°C (122°F) 80 6.0 bar
87 psig
101.5 psig
10 bar
5 145 psig
5.0 bar
Temperature Max.* Air Pilot operated: 80°C (176°F) 60 4.0 bar
72.5 psig
4 58 psig
Air Pilot port: 1/8"
40 3
Exhaust port: P31 - 1/4" / P32 - 1/2" 2.5 bar
2 36.3 psig
20
Typical flow with 6.3 bar 1
3
inlet pressure and 1 bar P31 17 dm /s (36 scfm) 0 0
3 0 5 10 15 20 25 30 35 40 45 50
pressure drop: P32 48 dm /s (97 scfm) Flow - dm3/s
* Air supply must be dry enough to avoid ice formation at temperatures below +2°C 0 20 40 60 80 100
Snap pressure: Full flow when downstream pressure reaches 50% of the inlet pressure Flow - (scfm)

1/2 Soft Start & Dump Valve

Material Specification 8
Inlet Pressure - 6.3 bar (91.3 psig)
9.0 bar
130.5psig
6.3 bar 8.0 bar
Body: Aluminum 100 7 91.4 psig 7 bar 116 psig

Secondary Pressure - (psig)

Secondary Pressure - bar

6.0 bar 101.5 psig
10 bar
Body cover: Polyester 6 87 psig 145 psig
80
5.0 bar
5
Seals: Nitrile NBR 72.5psig
60 4 4.0 bar
2.5 bar 58 psig
40 3 36.3 psig
2
Mounting Brackets 20
1
Description Order code Order code 0 0
P31P P32P 0 20 40 60 80 100 120 140
Flow - dm3/s
L-Bracket mounting kit P3HKA00ML P3KKA00ML 0 40 80 120 160 200 240 280
Foot bracket mounting kit P3HKA00MC P3KKA00MC Flow - (scfm)

Note:
For solenoid operators and cable plugs (connectors) see pages 68 to 69.

Dimensions
P31 P32
88
(3.46)

136
(5.35) 166
(6.53) 174.5
84
(3.30) (6.87)
37 227.5
109.5
(1.45) 64.5 (4.31) (8.95)
(2.53)
30.5
(1.20)
53
(2.08)
4
40
(1.57)
(0.15) 6 57.2
(0.23) (2.25)
24
(0.94) 26
57 (1.02) 75
(2.24) (2.95)
1 Start signal
2 Switching time delay
3 Gradual pressure build up
For mounting brackets see page 52 4 Operating pressure p2 (=p1)

Parker Hannifin Corporation

Pneumatic Division - Asia
63
1002-1/Asia Dec 2010
Parker One Pneumatic P31 / P32 Series

Dump Valve Symbols

• Modular design with 1/4" or 1/2" integral ports

(NPT, BSPP & BSPT)
• Provides for the safe introduction of pressure
• The 3-way, 2-position function automatically dumps
downstream pressure on the loss of pilot signal
• Adjustable slow start
• Solenoid or air pilot options
• High flow & exhaust capability
• Silencer included

To maintain these units in the open position a pilot supply

to the air pilot operated version or an electrical signal to
Remotely operated dump valves automatically shut off the solenoid operated version must be maintained.
upstream pressure and exhaust the downstream pressure The valve will automatically dump when the holding
when the pilot pressure is released. signal is removed.

Options:

Solenoid type only

P3 DA N

Body size Port size Pilot type 15mm (P31 series only) C 24VDC
Mini (1/4") 1 Mini (1/4") 2 External Air non locking
P 30mm CNOMO coil A 2CN
Pilot manual
Compact (1/2") 2 Compact (1/2") 4 30mm CNOMO coil overide
Solenoid Pilot S D
(M12 connection) 120VAC
Thread Type
Actuator interface non locking
BSPP (G) 1 3GN
manual
BSPT 2 15mm solenoid (P31 only) G
overide
NPT 9 30mm solenoid C
120VAC
Threaded air pilot P non locking
manual 1FN
Note: override (P31
P32 unit used for both P32 & P33 series series only)

Remote operated dump valve

Port Flow Max. Height Width Depth
Description Order Code† Weight
size dm3/s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)
1/4" 120VAC Solenoid & cable plug P31DA22SGNA1FN 17 (36) 10 (150) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/4" 24VDC Solenoid & cable plug P31DA22SGNC2CN 17 (36) 10 (150) 166* (6.5) 57 (2.2) 40 (1.5) 0.41kg (0.9lbs)
1/4" External air pilot operated P31DA22PPN 17 (36) 17 (250) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/2" 120VAC 30mm coil & cable plug incl. P32DA24SCNA3GN 51 (108) 10 (150) 162.5* (6.3) 75 (2.9) 57.2 (2.2) 0.69kg (1.5lbs)
1/2" 24VDC 30mm coil & cable plug incl. P32DA24SCNA2CN 51 (108) 10 (150) 227.5* (8.9) 75 (2.9) 57.2 (2.2) 0.91kg (2.0lbs)
1/2" External air pilot operated P32DA24PPN 51 (108) 17 (250) 162.5*(6.3) 75 (2.9) 57.2 (2.2) 0.87kg (1.9lbs)

* Includes exhaust silencer

† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
64
1002-1/Asia Dec 2010
Parker One Pneumatic P31 / P32 Series

Technical Information Flow characteristics

Fluid: Compressed air 1/4 Remote Dump Valve
Max. pressure Solenoid operated: 10 bar (150 psig) Inlet Pressure - 6.3 bar (91.3 psig)
8
8.0 bar
Max. pressure Air Pilot operated: 17 bar (250 psig) 116 psig
100 7 7 bar

Secondary Pressure - (psig)

Min. operating pressure: 3 bar (44 psig)

Secondary Pressure - bar

6.3 bar 101.5 psig
6 9.0 bar
6.0 bar 91.4 psig
Temperature Max.* Solenoid operated: 50°C (122°F) 80 87 psig
130.5 psig
5 5.0 bar
Temperature Max.* Air Pilot operated: 80°C (176°F) 60
72.5 psig
4 4.0 bar
Air Pilot port: 1/8" 58 psig
40 3 2.5 bar
Exhaust port: P31 - 1/4" / P32 - 1/2" 36.3 psig
2
Typical flow with 6.3 bar 20
1
3
inlet pressure and 1 bar P31 17 dm /s (36 scfm)
3 0 0
pressure drop: P32 51 dm /s (108 scfm) 0 5 10 15 20 25 30 35 40 45 50 55
Flow - dm3/s
* Air supply must be dry enough to avoid ice formation at temperatures below +2°C
Snap pressure: Full flow when downstream pressure reaches 50% of the inlet pressure 0 20 40 60 80 100
Flow - (scfm)

1/2 Remote Dump Valve

Inlet Pressure - 6.3 bar (91.3 psig)
Material Specification 8 9.0 bar
130.5 psig
6.3 bar 8.0 bar 10 bar
100 7 116 psig
Body: Aluminum 91.4 psig 7 bar 145 psig

Secondary Pressure - (psig)

Secondary Pressure - bar

6.0 bar 101.5 psig
6 87 psig
Body cover: Polyester 80
5.0 bar
5 72.5 psig
Seals: Nitrile NBR 60 4 4.0 bar
58 psig

40 3 2.5 bar
36.3 psig
2
20
Mounting Brackets 1

Description Order code Order code 0 0

0 20 40 60 80 100 120 140 160
P31P P32P Flow - dm3/s
L-Bracket mounting kit P3HKA00ML P3KKA00ML 0 40 80 120 160 200 240 280 320
Flow - (scfm)
Foot bracket mounting kit P3HKA00MC P3KKA00MC

Note:
For solenoid operators and cable plugs (connectors) see pages 68 to 69.

Dimensions
P31 P32
88
(3.46)

136
(5.35) 166
84 (6.53) 174.5
(3.30) (6.87)
37 109.5 227.5
(1.45) 64.5 (4.31) (8.95)
(2.53)
30.5
(1.20)
53
(2.08)
4
40
(1.57)
(0.15) 57.2
6
(2.25)
(0.23)
24
(0.94) 26
57
(2.24) (1.02) 75
(2.95)
For mounting brackets see page 52

Parker Hannifin Corporation

Pneumatic Division - Asia
65
1002-1/Asia Dec 2010
Parker One Pneumatic P31 / P32 Series

Soft Start Valve Symbols

• Modular design with 1/4" or 1/2" integral ports

(NPT, BSPP & BSPT)
• The 2-way, 2-position function provides for the safe
introduction of pressurel
• Adjustable slow start
• Solenoid or air pilot options
• High flow
• Silencer included

The controlled introduction of pressure can be an important

safety factor and prevent damage to tooling when air pressure
Parker Global Series Soft Start Valves, provide for the safe
is introduced at machine or system start up.
introduction of pressure to machines or systems. Soft Start
Valves, allow the pressure to gradually build to the set point Note: Soft Start Valves must be installed downstream of
before fully opening to deliver full flow at line pressure. a 3/2 valve with exhaust capability

Options:

Solenoid type only

P3 SA N

Body size Port size Pilot type 15mm (P31 series only) C 24VDC
Mini (1/4") 1 Mini (1/4") 2 External Air non locking
P 30mm CNOMO coil A 2CN
Pilot manual
Compact (1/2") 2 Compact (1/2") 4
30mm CNOMO coil overide
Solenoid Pilot S D
(M12 connection) 120VAC
Thread Type Internal Air
Y non locking
BSPP (G) 1 Pilot 3GN
manual
BSPT 2 overide
Actuator interface
NPT 9 120VAC
Internal Pilot 0
non locking
15mm solenoid (P31 only) G manual 1FN
30mm solenoid C override (P31
Note:
P32 unit used for both P32 & P33 series Threaded air pilot P series only)

Soft start valve

Port Flow Max. Height Width Depth
Description Order Code† Weight
size dm3/s (scfm) bar (psig) mm (inches) mm (inches) mm (inches)
1/4" 120VAC Solenoid & cable plug P31SA22SGNA1FN 17 (36) 10 (150) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/4" 24VDC Solenoid & cable plug P31SA22SGNC2CN 17 (36) 10 (150) 166.0 (6.5) 57 (2.2) 40 (1.5) 0.41kg (0.9lbs)
1/4" Internal air pilot operated P31SA22Y0N 17 (36) 17 (250) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/4" External air pilot (1/8" threaded) P31SA22PPN 17 (36) 17 (250) 115.6 (4.5) 57 (2.2) 40 (1.5) 0.37kg (0.8lbs)
1/2" 120VAC 30mm coil & cable plug incl. P32SA24SCNA3GN 48 (101) 10 (150) 162.5 (6.3) 88 (3.4) 57.2 (2.28) 0.87kg (1.5lbs)
1/2" 24VDC 30mm coil & cable plug P32SA24SCNA2CN 48 (101) 10 (150) 227.5 (8.9) 88 (3.4) 57.2 (2.28) 0.90kg (2.0lbs)
1/2" Internal air pilot operated P32SA24Y0N 48 (101) 17 (250) 162.5 (6.3) 75 (2.9) 57.2 (2.28) 0.90kg (2.0lbs)
1/2" External air pilot (1/8 threaded) P32SA24PPN 48 (101) 17 (250) 162.5 (6.3) 75 (2.9) 57.2 (2.28) 0.87kg (1.5lbs)

† Standard part numbers shown in bold. For other models refer to Options chart above.

Parker Hannifin Corporation

Pneumatic Division - Asia
66
1002-1/Asia Dec 2010
Parker One Pneumatic P31 / P32 Series

Technical Information Flow characteristics

Fluid: Compressed air 1/4 Soft Start Valve
Max. pressure Solenoid operated: 10 bar (150 psig) Inlet Pressure - 6.3 bar (91.3 psig)
8
Max. pressure Air Pilot operated: 17 bar (250 psig) 9.0 bar
130.5 psig
100 7
Min. operating pressure: 3 bar (44 psig) 6.3 bar 8.0 bar

Secondary Pressure - (psig)

Secondary Pressure - bar

91.4 psig 7 bar 116 psig
6
Temperature Max.* Solenoid operated: 50°C (122°F) 80 6.0 bar 101.5 psig
10 bar
87 psig
5 145 psig
Temperature Max.* Air Pilot operated: 80°C (176°F) 5.0 bar
72.5 psig
60 4 4.0 bar
Air Pilot port: 1/8" 58 psig

40 3
Typical flow with 6.3bar 2.5 bar
3 2 36.3 psig
inlet pressure and 1 bar P31 17 dm /s (36 scfm) 20
pressure drop: P32 48 dm3/s (97 scfm) 1

* Air supply must be dry enough to avoid ice formation at temperatures below +2°C 0 0
0 5 10 15 20 25 30 35 40 45 50
Snap pressure: Full flow when downstream pressure reaches 50% of the inlet pressure Flow - dm3/s
0 20 40 60 80 100
Flow - (scfm)
1/2 Soft Start Valve
Material Specification Inlet Pressure - 6.3 bar (91.3 psig)
9.0 bar
8 130.5psig
Body: Aluminum 6.3 bar 8.0 bar
100 7 91.4 psig 7 bar 116 psig

Secondary Pressure - (psig)

Body cover: Polyester

Secondary Pressure - bar

6.0 bar 101.5 psig
10 bar
6 87 psig 145 psig
80
Seals: Nitrile NBR 5 5.0 bar
72.5psig
60 4 4.0 bar
2.5 bar 58 psig
40 3 36.3 psig

Mounting Brackets 20
2
1
Description Order code Order code
P31P P32P 0 0
0 20 40 60 80 100 120 140
Flow - dm3/s
L-Bracket mounting kit P3HKA00ML P3KKA00ML
0 40 80 120 160 200 240 280
Foot bracket mounting kit P3HKA00MC P3KKA00MC Flow - (scfm)

Note:
For solenoid operators and cable plugs (connectors) see pages 68 to 69.

Dimensions
P31 P32 88
(3.46)

136
(5.35) 166 174.5
(6.53) (6.87)
84
(3.30) 109.5 227.5
37 (4.31) (8.95)
(1.45) 64.5
(2.53)
30.5
(1.20)
53
(2.08)

4
40
(1.57)
(0.15) 57.2
6
(0.23) (2.25)
24
(0.94) 26
57 1 Start signal
(2.24) 2 Switching time delay (1.02) 75
3 Gradual pressure build up (2.95)
For mounting brackets see page 52 4 Operating pressure p2 (=p1)

Parker Hannifin Corporation

Pneumatic Division - Asia
67
1002-1/Asia Dec 2010
Parker One Pneumatic Solenoid Operators

Solenoid Operator - CNOMO

Technical data - Transients

Solenoid operators, coil combinations Interrupting the current through the solenoid coil produces momentary
NC Normal NC Normal NC Normal voltage peaks which, under unfavourable conditions, can amount to
Operator Operator Operator several hundred times the rated operating voltage. Normally, these
with 15mm with 22 x 30 with 30 x 30 transients do not cause problems, but to achieve the Maximum life
standard coil standard coil standard coil of relays in the circuit (and particularly of transistors, thyristors and
integrated circuits) it is desirable to provide protection by means of
Working pressure 0 to10 bar 0 to 10 bar 0 to10 bar
voltage-dependent resistors (varistors). All connectors/cable plugs
Ambient -15°C to 60°C * -10°C to 60°C * -10°C to 60°C * EN175301-803 with LED’s include this type of circuit protection.
temperature
Power (DC) 1.2W 4.8W 2.7W
Materials
Power (AC) 1.6VA 8.5VA 4.9VA Pilot Valve
Voltage tolerance +10%/-15% +/-10% +/-10% Body: Polyamide
Duty cycle 100% 100% 100% Armature tube: Brass
Insulation class F F F Plunger & core: Corrosion resistant Cr-Ni steel
Electric connection ISO 15217 B Industrial DIN 43650A Seals: Fluorocarbon
Protection IP65 IP65 IP65 Screws: Stainless steel
Approval UL/CSA UL/CSA Coil
Working media All neutral media such as compressed air Encapsualtion material: Thermoplastic as standard
and inert gases. Duroplast for M12 connection
* limited to 50°C if use with 100% duty cycle

P31 Series only - Solenoid coils 15mm NC Spare solenoid operators

Order code Base Solenoid pilot operator CNOMO NC
Weight
Voltage Override, blue, Order code
(Kg) Weight
non locking flush Description Non-lock manual
(Kg)
override
1
‰

0
1
24VDC PS2982B49P 0.038
‰

115VAC 50 Hz / Standard Duty P2FP23N4B 0.065

PS2982B53P 0.038
120VAC 60 Hz No Override P2FP23N4A 0.065
Note: Solenoid pilot operators are fitted to the Global range. Order the above part numbers for
spares. The operators are supplied with mounting screws and interface ‘O’ rings.
Coils and connectors must be ordered separately.

Solenoid coils with M12 connection

Weight
Voltage Order code
(Kg)

Direct current
24VDC P2FC6449 0.065

Solenoid coils with Din A or Industrial B connection

30mm x 30mm
22mm x 30mm
Weight Order code Weight
Voltage Order code
(Kg) DIN 43650A (Kg)
B Industrial Standard
Standard
Direct current
24VDC P2FCB449 0.093 P2FCA449 0.105
Alternative current
110V 50Hz, 120V 60Hz P2FCB453 0.093 P2FCA453 0.105

Parker Hannifin Corporation

Pneumatic Division - Asia
68
1002-1/Asia Dec 2010
Parker One Pneumatic Solenoid Coils & Cable Plugs

Solenoid connectors / Cable plugs EN175301-803

Order code Order code Order code
Description 15mm Form C 22mm Form B 30mm Form A
ISO15217 Industrial DIN 43650A
With standard screw Standard IP65
PS2932BP PS2429BP PS2028BP
without flying lead
With LED and protection
PS294679BP PS243079BP PS203279BP
24VAC/DC
With LED and protection
PS294683BP PS243083BP PS203283BP
110VAC
With cable Standard with 2m cable IP65 PS2932JBP PS2429JBP PS2028JBP
24VAC/DC, 2m cable
PS2946J79BP PS2430J79BP PS2032J79BP
LED and protection IP65
110VAC/DC, 2m cable
PS2946J83BP PS2430J83BP PS2032J83BP
LED and protection IP65

Solenoid coil
Dimensions mm (inches) Electrical schematics
15mm 22 x 30mm
23.65
(.93)
30 22
15 (1.18) (.86)
1
0

(.59)
1

41
3.4
25.5 (.13) 45 (1.61) 33
(1.30)
(1.00) (1.77) 31 PS2028BP PS243079BP PS203279BP
(1.22)
PS2028JBP PS2430J79BP PS2032J79BP
40
(1.57) 22
PS2429BP PS243083BP PS293283BP
51 (.87)
(2.01)
60 PS2429JBP PS2430J83BP PS2932J83BP
30 x 30mm (2.36)
PS2932BP PS294679BP PS294683BP
30 PS2932JBP PS2946J79BP PS2946J83BP
(1.18)

48
(1.89)
36 31
(1.42) (1.22)

22
52 (.87)
60 (2.05)
(2.36)

Cable plug
Dimensions
15mm ISO 15217 22mm Form B Industrial 30mm DIN 43650A
Cable plugs Cable plugs Cable plugs
PS2932BP PS2429BP PS2028BP
PS294679BP
40
35 (1.57) 31
(1.38) (1.22)

30
42
25 (1.18)
(1.65)
(.98) 47.5
(1.87)

5.5 31
(.22) (1.22) 30
(1.18) 32
1

15.5 (1.26)
(.61) 20.8
2

(.82)
15.5
M3 31 5
(.61)
(1.22) (.20)

Parker Hannifin Corporation

Pneumatic Division - Asia
69
1002-1/Asia Dec 2010
Parker One Pneumatic P31, P32 / P33 Series

Safety Lockout Valves

Features
• The Safety Lockout valve is a manually operated, slide-type,
2-position, 3-way valve. In the closed position, downstream
air pressure is exhausted to atmosphere.
• The valve slide can be locked in the closed position with a
customer supplied padlock.
• The Safety Lockout valves conform to OSHA #29 CFR
part 1910 – control of hazardous energy source (lockout /
tagout).
• Left to right flow — orange slide
• Right to left — yellow slide
Ordering Information
Port Thread Flow Safety Lockout Valve Safety Lockout Valve
Model type
size type dm3/s (scfm) Flow from left to right Flow from right to left
P31 1/4" NPT 47.2 (100) P31VA22LSAN P31VA22LSBN
P32 1/4" NPT 66.5 (141) P32VA22LSAN P32VA22LSBN
3/8" NPT 101.9 (216) P32VA23LSAN P32VA23LSBN
1/2" NPT 128.4 (272) P32VA24LSAN P32VA24LSBN
P33 1/2" NPT 136.9 (290) P33VA24LSAN P33VA24LSBN
3/4" NPT 141.6 (300) P33VA26LSAN P33VA26LSBN

For thread type: BSPP 1

BSPT 2
NPT 9

Materials of Construction Specifications

Body Zinc Max. operating temperature 65.5°C (150°F)

Blade Acetal Max. supply pressure 10 bar (150 psig)

Seals Nitrile Port size BSPP / BSPT / NPT 1/4, 3/8, 1/2, 3/4

Weight P31: 0.30 kg (0.66 lbs)

P32: 0.34 kg (0.74 lbs)
Dimensions P33: 0.41 kg (0.90 lbs)

P31 P32 P33

49 50
42.7 (1.91) (1.96)
80 26 80 26
(1.68)
21.3 (3.16) (1.03) (3.14) (1.02)
(0.84) 58 60 65
58
(2.28) (2.36) (2.58)
(2.28) 33
30
(1.18) (1.29)
20
(0.79)
40 62.5
(1.58) (2.46) 24.5
41.4 80 (0.97) 86 29
(1.63) (3.19) (3.41) 54 (1.14) 58
51 49
(2.02) (1.93) (2.13) (2.28)
30.7
(1.21)
61.2
(2.41)

Parker Hannifin Corporation

Pneumatic Division - Asia
70
1002-1/Asia Dec 2010
Parker One Pneumatic P31, P32 / P33 Series

Modular Ball Valve

Features
The Modular Ball Valves provide shut off line pressure with
a non-sticking 90O turn handle to prevent unauthorised
adjustment. When the inlet pressure is turned off the
downstream air pressure vents through the exhaust port.
The padlock slide may be assembled on either side. It is
recommended that this is assembled after mounting.
Note: This padlock slide is a permanent assembly and may not be
removed later

Ordering Information Specifications

Port Thread Flow Modular Ball Valve Max. supply pressure 17 bar (250 psig)
Model type
size type dm3/s (scfm) Flow from left to right
Port size BSPP / BSPT / NPT 1/4, 3/8, 1/2, 3/4
P31 1/4" NPT 20 (42.4) P31VA22LBNN
Weight P31: 0.19 kg (0.41 lbs)
P32 3/8" NPT 90 (190.7) P32VA23LBNN
P32: 0.47 kg (1.00 lbs)
1/2" NPT 122 (258.5) P32VA24LBNN
P33: 0.80 kg (1.70 lbs)
P33 1/2" NPT 265 (561.5) P33VA24LBNN
3/4" NPT 320 (678) P33VA26LBNN
For thread type: BSPP 1
BSPT 2
NPT 9

Materials of Construction
Body Aluminum
Seals PTFE
Ball P31 Brass
P32 / P33 Chrome plated brass

Dimensions

P31 P32 P33

60
42 (2.36)
(1.65) 30
(1.18) 36.5
(1.43)
30 73
20 (2.87)
(1.18)
40 (0.78) 60
(1.57) (2.36)

87
67 36.5 (3.42)
50 (2.63) (1.43) 73
21 (1.96) (2.87)
(0.82)

89 100
71 (2.36) (3.93)
(2.79)

22 26 36.5
(0.86) (1.02) (1.43)

Parker Hannifin Corporation

Pneumatic Division - Asia
71
1002-1/Asia Dec 2010
Parker One Pneumatic P31, P33 Series

Manifold Blocks

Features
• Available in 1/4" or 3/4" threaded inlet / outlet ports
• Two additional top and bottom auxiliary ports standard
• Can be mounted anywhere in the FRL system
• Includes one pipe plug

Ordering Information Specifications

Model In / Out Auxiliary Auxilliary Thread Order Code Max. operating temperature 65.5°C (150°F)
type port size port size port size type
Top Bottom Max. supply pressure 20.7 bar (300 psig)

P31 1/4" 1/4" 1/4" NPT P31MA22022N Port size (In / Out) P31: 1/4"
P33 3/4" 1/4" 1/2" NPT P33MA26024N NPT / BSPP / BSPT / NPT P33: 3/4"

For thread type: BSPP 1 Auxilliary port size - Top P31: 1/4"
BSPT 2
NPT / BSPP / BSPT P33: 1/4"
NPT 9
Auxilliary port size - Bottom P31: 1/4"
Materials of Construction
BSPP / BSPT / NPT P33: 1/2"
Body Aluminum
Weight P31: 0.19 kg (0.26 lbs)
Note:
P33: 0.34 kg (0.42 lbs)
P33 unit used for both P32 & P33 series

Dimensions
P31 P33
Top Port 1/4" Outlet Port 3/4"
42
(1.66)

Inlet Port 3/4"

20
(0.79) 73
40 (2.88)
(1.58)
36.5
Top and bottom (1.44)
aux. ports 1/4"
33
(1.30)
66
Inlet port 1/4" Outlet port 1/4" (2.60)
Flow

19 23.9
(0.94)
(0.74) 47.8
41 40 (1.88)
(1.61) (1.58)

Bottom Port 1/2"

Parker Hannifin Corporation

Pneumatic Division - Asia
72
1002-1/Asia Dec 2010
Parker One Pneumatic P31 Series

Accessories - P31 Series

C-Bracket T-Bracket w/ Body Connector

(Fits to filter and lubricator body) P31KA00MT
7
P31KA00MW 68 (.28)
(2.68) 10
(.39) 5.5
42.5
(1.67) (.22)
6.6
10 (.26)
(.39)
35.5
(1.40)
19.3 Dia 90
(.76) (3.54)
62 2
(2.44) (.08)
16
60 40 (.63)
(2.36) (1.57)
40 10
(1.57) (.39)

Body Connector Port Block Kit

(O-ring not shown) 1/8 NPT..................... P31KA91CP
P31KA00CB 1/4 NPT .................... P31KA92CP
3/8 NPT..................... P31KA93CP
G 1/8......................... P31KA11CP
G 1/4 ........................ P31KA12CP
G 3/8......................... P31KA13CP
10
(.39)

36
(1.42)

24
(.94)

Port Block Kit Angle Bracket

w/ T-Bracket (Fits to regulator and filter/regulator body)
1/8 NPT.............P31KA91CN P31KA00MR
1/4 NPT ............P31KA92CN
3/8 NPT.............P31KA93CN 68
(2.68)
G 1/8.................P31KA11CN 44
G 1/4 ................P31KA12CN (1.73)
G 3/8.................P31KA13CN
25 30 Dia.
(.98) (1.18)

40
(1.57)

Angle Bracket

Parker Hannifin Corporation

Pneumatic Division - Asia
73
1002-1/Asia Dec 2010
Parker One Pneumatic P32 Series

Accessories - P32 Series

T-Bracket w/ Body Connector Body Connector

P32KA00MT P32KA00CB

8.9
8.9 (.35)
(.35)

O-Ring

O-Ring O-Ring
22.1 Dia. 22.1
Dia.
(.87) (.87)

Port Block Kit Angle Bracket

1/4 NPT......................P32KA92CP (Fits to regulator and filter/regulator bonnet)
3/8 NPT......................P32KA93CP
P32KA00MR
1/2 NPT......................P32KA94CP 69.5
3/4 NPT......................P32KA96CP (2.74)
G 1/4 .........................P32KA12CP 42
(1.65)
G 3/8..........................P32KA13CP
G 1/2..........................P32KA14CP 14 7.1
(.55) (.28)
G 3/4..........................P32KA16CP 11
(.43)
51 Dia
25 (2.01)
(98)

69.5
(2.74)
40
(1.57)
40
(1.57)

L-Bracket T-Bracket
(Fits to filter and lubricator body) (fits to body connector or port block)
P32KA00ML P32KA00MB
69.5
(2.74)
14 42 7.1 19 7.5 (Typ.)
(.54) (1.66) (.28) (.75) (.29)
9.6
(.38)
57 Dia
28 (2.25)
(1.10)

22
25.4
72 (.88)
(2.84) 115 (1.00)
32 (4.53)
(1.26)
7.0
(.28)

20
(.79 )

Parker Hannifin Corporation

Pneumatic Division - Asia
74
1002-1/Asia Dec 2010
P33 Series
Parker One Pneumatic

Accessories - P33 Series

T-Bracket w/ Body Connector Body Connector

P32KA00MT P32KA00CB

8.9
8.9 (.35)
(.35)

O-Ring

O-Ring O-Ring
22.1 Dia. 22.1
Dia.
(.87) (.87)

Port Block Kit Angle Bracket

1/4 NPT......................P32KA92CP (Fits to regulator and filter/regulator
3/8 NPT......................P32KA93CP bonnet)
1/2 NPT......................P32KA94CP
P33KA00MR
3/4 NPT......................P32KA96CP 76
G 1/4 .........................P32KA12CP (2.99)
G 3/8..........................P32KA13CP 48
(1.89)
G 1/2..........................P32KA14CP 14 61
G 3/4..........................P32KA16CP (.55) (2.40)
11
(.43)
61 Dia
25 (2.40)
(98)

84.5
(3.33)
49
40 (1.92)
(1.57)

L-Bracket T-Bracket
(Fits to filter and lubricator body) (fits to body connector or port block)
P33KA00ML P32KA00MB
76
(3.00)
14 48 7.1 19 7.5 (Typ.)
(.56) (1.88) (.28) (.75) (.29)
9.6
(.38)
67.5 Dia
28 (2.66)
(1.10)

28 25.4
87 (1.10)
(3.44) 115 (1.00)
38 (4.53)
(1.49)
7.0
(.28)

20
(.79 )

Parker Hannifin Corporation

Pneumatic Division - Asia
75
1002-1/Asia Dec 2010
Parker One Pneumatic Kits

Kits

Series Description Order Code

P31 P31KA00MP
P32 Panel Mount Nut (Plastic) P32KA00MP
P33 P33KA00MP

P31 P31KA00MM
P32 Panel Mount Nut (Aluminum) P32KA00MM
P33 P33KA00MM

P31 P31KA00ESE
P32 5µ Element Kit P32KA00ESE
P33 P33KA00ESE

P31 P31KA00ES9
P32 1µ Element Kit P32KA00ES9
P33 P33KA00ES9

P31 P31KA00ESC
P32 0.01µ Element Kit P32KA00ESC
P33 P33KA00ESC

P31 P31KA00ESA
P32 Adsorber Element Kit P32KA00ESA
P33 P33KA00ESA

P32 / P33 Auto Drain Kit P32KA00DA

P32 / P33 Differential Pressure Indicator Kit P32KA00RQ

P31 P31KA00PL
P32/P33 Fill Plug Kit P32KA00PL

P31 / P32 / P33 Drip Control Assembly Kit P31KA00PG

Parker Hannifin Corporation

Pneumatic Division - Asia
76
1002-1/Asia Dec 2010
Parker One Pneumatic Kits

Kits

Series Description Order Code

P31 P31KA00BGM
P32 Plastic Bowl w/ Bowl Guard & Manual Drain P32KA00BGM
P33 P33KA00BGM

P31 Plastic Bowl w/ Bowl Guard & Pulse Drain P31KA00BGB

P32 P32KA00BGA
Plastic Bowl w/ Bowl Guard & Auto Drain
P33 P33KA00BGA

P31 P31KA00BMM
P32 Metal Bowl w/o Sight Gauge & Manual Drain P32KA00BMM
P33 P33KA00BMM

P31 Metal Bowl w/o Sight Gauge & Pulse Drain P31KA00BMB

P32 P32KA00BMA
Metal Bowl w/o Sight Gauge & Auto Drain
P33 P33KA00BMA

P32 P32KA00BSM
Metal Bowl w/ Sight Gauge & Manual Drain
P33 P33KA00BSM

P32 P32KA00BSA
Metal Bowl w/ Sight Gauge & Auto Drain
P33 P33KA00BSA

P31 P31KA00BGN
P32 Lubricator - Plastic Bowl w/ Bowl Guard No Drain P32KA00BGN
P33 P33KA00BGN

P31 P31KA00RB
P32 Regulator - Relieving Repair Kit P32KA00RB
P33 P33KA00RB

P31 P31KA00RC
P32 Regulator - Non Relieving Repair Kit P32KA00RC
P33 P33KA00RC

Parker Hannifin Corporation

Pneumatic Division - Asia
77
1002-1/Asia Dec 2010
Parker One Pneumatic Kits

Kits

Series Description Connection Order Code

P31 P31KA00PR
P32 Regulator - Main Adjusting Spring 0-2 bar (0-30 psig) Kit P32KA00PR
P33 P33KA00PR

P31 P31KA00PS
P32 Regulator - Main Adjusting Spring 0-4.1 bar (0-60 psig) Kit P32KA00PS
P33 P33KA00PS

P31 P31KA00PT
P32 Regulator - Main Adjusting Spring 0-8.6 bar (0-125 psig) Kit P32KA00PT
P33 P33KA00PT

P32 P32KA00PV
Regulator - Main Adjusting Spring 0-17 bar (0-250 psig) Kit
P33 P33KA00PV

15
0-0.4 Mpa K4511SCR04M (.59)

0-1.1 Mpa K4511SCR11M

Square Flush 0-4.1 bar K4511SCR04B 27
P31 (1.06)
Mounting Gauge Kit 0-11 bar K4511SCR11B
0-60 psig K4511SCR060 27
0-150 psig K4511SCR150 (1.06)

0-2 bar/0-0.2 Mpa 1/8" K4515R1402B

40mm Round Gauge
P31 0-4.1 bar/0-0.4 Mpa 1/8" K4515R1404B
16 40
0-11 bar/0-1.1 Mpa 1/8" K4515R1411B (.63)
25
(1.57)
(.98)

0-2 bar/0-0.2 Mpa/0-30 psig 1/4" K4520R1402B

0-4.1 bar/0-0.4 Mpa/0-60 psig 1/4" K4520R1404B
P32 / P33 50mm Round Gauge
0-11 bar/0-1.1 Mpa/0-160 psig 1/4" K4520R1411B 18 50
(1.97)
(.71)
0-20 bar/0-2 Mpa/0-300 psig 1/4" K4520R1420B 24
(.94)

Parker Hannifin Corporation

Pneumatic Division - Asia
78
1002-1/Asia Dec 2010
Parker One Pneumatic Notes

Parker Hannifin Corporation

Pneumatic Division - Asia
79
1002-1/Asia Dec 2010
Parker One Pneumatic Safety Guide

Safety Guide For Selecting And Using Pneumatic Division

Products And Related Accessories
! WARNING:
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF PNEUMATIC DIVISION PRODUCTS,
ASSEMBLIES OR RELATED ITEMS (“PRODUCTS”) CAN CAUSE DEATH, PERSONAL INJURY, AND
PROPERTY DAMAGE. POSSIBLE CONSEQUENCES OF FAILURE OR IMPROPER SELECTION OR
IMPROPER USE OF THESE PRODUCTS INCLUDE BUT ARE NOT LIMITED TO:
• Unintended or mistimed cycling or motion of machine members or failure to cycle
• Work pieces or component parts being thrown off at high speeds.
• Failure of a device to function properly for example, failure to clamp or unclamp an associated item or device.
• Explosion
• Suddenly moving or falling objects.
• Release of toxic or otherwise injurious liquids or gasses.
Before selecting or using any of these Products, it is important that you read and follow the instructions below.

1. GENERAL INSTRUCTIONS
1.1. Scope: This safety guide is designed to cover general guidelines on the installation, use, and maintenance of Pneumatic Division
Valves, FRLs (Filters, Pressure Regulators, and Lubricators), Vacuum products and related accessory components.
1.2. Fail-Safe: Valves, FRLs, Vacuum products and their related components can and do fail without warning for many reasons. Design all
systems and equipment in a fail-safe mode, so that failure of associated valves, FRLs or Vacuum products will not endanger persons
or property.
1.3 Relevant International Standards: For a good guide to the application of a broad spectrum of pneumatic fluid power devices see:
ISO 4414:1998, Pneumatic Fluid Power – General Rules Relating to Systems. See www.iso.org for ordering information.
1.4. Distribution: Provide a copy of this safety guide to each person that is responsible for selection, installation, or use of Valves, FRLs
or Vacuum products. Do not select, or use Parker valves, FRLs or vacuum products without thoroughly reading and understanding this
safety guide as well as the specific Parker publications for the products considered or selected.
1.5. User Responsibility: Due to the wide variety of operating conditions and applications for valves, FRLs, and vacuum products Parker
and its distributors do not represent or warrant that any particular valve, FRL or vacuum product is suitable for any specific end use
system. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The user, through
its own analysis and testing, is solely responsible for:
• Making the final selection of the appropriate valve, FRL, Vacuum component, or accessory.
• Assuring that all user’s performance, endurance, maintenance, safety, and warning requirements are met and that the application
presents no health or safety hazards.
• Complying with all existing warning labels and / or providing all appropriate health and safety warnings on the equipment on which
the valves, FRLs or Vacuum products are used; and,
• Assuring compliance with all applicable government and industry standards.
1.6. Safety Devices: Safety devices should not be removed, or defeated.
1.7. Warning Labels: Warning labels should not be removed, painted over or otherwise obscured.
1.8. Additional Questions: Call the appropriate Parker technical service department if you have any questions or require any additional
information. See the Parker publication for the product being considered or used, or call 1-800-CPARKER, or go to www.parker.com,
for telephone numbers of the appropriate technical service department.
2. PRODUCT SELECTION INSTRUCTIONS
2.1. Flow Rate: The flow rate requirements of a system are frequently the primary consideration when designing any pneumatic system.
System components need to be able to provide adequate flow and pressure for the desired application.
2.2. Pressure Rating: Never exceed the rated pressure of a product. Consult product labeling, Pneumatic Division catalogs or the
instruction sheets supplied for Maximum pressure ratings.
2.3. Temperature Rating: Never exceed the temperature rating of a product. Excessive heat can shorten the life expectancy of a product
and result in complete product failure.
2.4. Environment: Many environmental conditions can affect the integrity and suitability of a product for a given application. Pneumatic
Division products are designed for use in general purpose industrial applications. If these products are to be used in unusual
circumstances such as direct sunlight and/or corrosive or caustic environments, such use can shorten the useful life and lead to
premature failure of a product.
2.5. Lubrication and Compressor Carryover: Some modern synthetic oils can and will attack nitrile seals. If there is any possibility of
synthetic oils or greases migrating into the pneumatic components check for compatibility with the seal materials used. Consult the
factory or product literature for materials of construction.
2.6. Polycarbonate Bowls and Sight Gauges: To avoid potential polycarbonate bowl failures:
• Do not locate polycarbonate bowls or sight gauges in areas where they could be subject to direct sunlight, impact blow, or
temperatures outside of the rated range.
• Do not expose or clean polycarbonate bowls with detergents, chlorinated hydro-carbons, keytones, esters or certain alcohols.
• Do not use polycarbonate bowls or sight gauges in air systems where compressors are lubricated with fire resistant fluids such as
phosphate ester and di-ester lubricants.

Parker Hannifin Corporation

Pneumatic Division - Asia
80
1002-1/Asia Dec 2010
Parker One Pneumatic Safety Guide

2.7. Chemical Compatibility: For more information on plastic component chemical compatibility see Pneumatic Division technical bulletins
Tec-3, Tec-4, and Tec-5
2.8. Product Rupture: Product rupture can cause death, serious personal injury, and property damage.
• Do not connect pressure regulators or other Pneumatic Division products to bottled gas cylinders.
• Do not exceed the Maximum primary pressure rating of any pressure regulator or any system component.
• Consult product labeling or product literature for pressure rating limitations.
3. PRODUCT ASSEMBLY AND INSTALLATION INSTRUCTIONS
3.1. Component Inspection: Prior to assembly or installation a careful examination of the valves, FRLs or vacuum products must be
performed. All components must be checked for correct style, size, and catalog number. DO NOT use any component that displays any
signs of nonconformance.
3.2. Installation Instructions: Parker published Installation Instructions must be followed for installation of Parker valves, FRLs and
vacuum components. These instructions are provided with every Parker valve or FRL sold, or by calling 1-800-CPARKER, or at
www.parker.com.
3.3. Air Supply: The air supply or control medium supplied to Valves, FRLs and Vacuum components must be moisture-free if ambient
temperature can drop below freezing
4. VALVE AND FRL MAINTENANCE AND REPLACEMENT INSTRUCTIONS
4.1. Maintenance: Even with proper selection and installation, valve, FRL and vacuum products service life may be significantly reduced
without a continuing maintenance program. The severity of the application, risk potential from a component failure, and experience
with any known failures in the application or in similar applications should determine the frequency of inspections and the servicing or
replacement of Pneumatic Division products so that products are replaced before any failure occurs. A maintenance program must
be established and followed by the user and, at Minimum, must include instructions 4.2 through 4.10.
4.2. Installation and Service Instructions: Before attempting to service or replace any worn or damaged parts consult the appropriate
Service Bulletin for the valve or FRL in question for the appropriate practices to service the unit in question. These Service and
Installation Instructions are provided with every Parker valve and FRL sold, or are available by calling 1-800-CPARKER, or by accessing
the Parker web site at www.parker.com.
4.3. Lockout / Tagout Procedures: Be sure to follow all required lockout and tagout procedures when servicing equipment. For more
information see: OSHA Standard – 29 CFR, Part 1910.147, Appendix A, The Control of Hazardous Energy – (Lockout / Tagout)
4.4. Visual Inspection: Any of the following conditions requires immediate system shut down and replacement of worn or damaged
components:
• Air leakage: Look and listen to see if there are any signs of visual damage to any of the components in the system. Leakage is an
indication of worn or damaged components.
• Damaged or degraded components: Look to see if there are any visible signs of wear or component degradation.
• Kinked, crushed, or damaged hoses. Kinked hoses can result in restricted air flow and lead to unpredictable system behavior.
• Any observed improper system or component function: Immediately shut down the system and correct malfunction.
• Excessive dirt build-up: Dirt and clutter can mask potentially hazardous situations.
Caution: Leak detection solutions should be rinsed off after use.
4.5. Routine Maintenance Issues:
• Remove excessive dirt, grime and clutter from work areas.
• Make sure all required guards and shields are in place.
4.6. Functional Test: Before initiating automatic operation, operate the system manually to make sure all required functions operate
properly and safely.
4.7. Service or Replacement Intervals: It is the user’s responsibility to establish appropriate service intervals. Valves, FRLs and vacuum
products contain components that age, harden, wear, and otherwise deteriorate over time. Environmental conditions can significantly
accelerate this process. Valves, FRLs and vacuum components need to be serviced or replaced on routine intervals. Service intervals
need to be established based on:
• Previous performance experiences.
• Government and / or industrial standards.
• When failures could result in unacceptable down time, equipment damage or personal injury risk.
4.8. Servicing or Replacing of any Worn or Damaged Parts: To avoid unpredictable system behavior that can cause death, personal
injury and property damage:
• Follow all government, state and local safety and servicing practices prior to service including but not limited to all OSHA Lockout
Tagout procedures (OSHA Standard – 29 CFR, Part 1910.147, Appendix A, The Control of Hazardous Energy – Lockout / Tagout).
• Disconnect electrical supply (when necessary) before installation, servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to system and Pneumatic Division products before installation, service,
or conversion.
• Installation, servicing, and / or conversion of these products must be performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversions air and electrical supplies (when necessary) should be connected and the product tested
for proper function and leakage. If audible leakage is present, or if the product does not operate properly, do not put product or
system into use.
• Warnings and specifications on the product should not be covered or painted over. If masking is not possible, contact your local
representative for replacement labels.
4.9. Putting Serviced System Back into Operation: Follow the guidelines above and all relevant Installation and Maintenance Instructions
supplied with the valve FRL or vacuum component to insure proper function of the system.

Parker Hannifin Corporation

Pneumatic Division - Asia
81
1002-1/Asia Dec 2010
Parker One Pneumatic Offer of Sale

The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized
distributors, are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This
offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any such item, when
communicated to Parker Hannifin Corporation, its subsidiaries or an authorized distributor (“Seller”) verbally or in writing, shall constitute acceptance of
this offer.
1. Terms and Conditions of Sale: All descriptions, quotations, proposals, 8. Buyer’s Property: Any designs, tools, patterns, materials, drawings,
offers, acknowledgments, acceptances and sales of Seller’s products are confidential information or equipment furnished by Buyer, or any other
subject to and shall be governed exclusively by the terms and conditions items which become Buyer’s property, may be considered obsolete and
stated herein. Buyer’s acceptance of any offer to sell is limited to these may be destroyed by Seller after two (2) consecutive years have elapsed
terms and conditions. Any terms or conditions in addition to, or incon- without Buyer placing an order for the items which are manufactured us-
sistent with those stated herein, proposed by Buyer in any acceptance ing such property. Seller shall not be responsible for any loss or damage
of an offer by Seller, are hereby objected to. No such additional, different to such property while it is in Seller’s possession or control.
or inconsistent terms and conditions shall become part of the contract 9. Taxes: Unless otherwise indicated on the face hereof, all prices and
between Buyer and Seller unless expressly accepted in writing by Seller. charges are exclusive of excise, sales, use, property, occupational or like
Seller’s acceptance of any offer to purchase by Buyer is expressly condi- taxes which may be imposed by any taxing authority upon the manufacture,
tional upon Buyer’s assent to all the terms and conditions stated herein, sale or delivery of the items sold hereunder. If any such taxes must be paid
including any terms in addition to, or inconsistent with those contained in by Seller or if Seller is liable for the collection of such tax, the amount thereof
Buyer’s offer. Acceptance of Seller’s products shall in all events constitute shall be in addition to the amounts for the items sold. Buyer agrees to pay
such assent. all such taxes or to reimburse Seller therefore upon receipt of its invoice. If
2. Payment: Payment shall be made by Buyer net 30 days from the date of Buyer claims exemption from any sales, use or other tax imposed by any
delivery of the items purchased hereunder. Amounts not timely paid shall taxing authority, Buyer shall save Seller harmless from and against any such
bear interest at the Maximum rate permitted by law for each month or por- tax, together with any interest or penalties thereon which may be assessed
tion thereof that the Buyer is late in making payment. Any claims by Buyer if the items are held to be taxable.
for omissions or shortages in a shipment shall be waived unless Seller re- 10. Indemnity For Infringement of Intellectual Property Rights: Seller shall
ceives notice thereof within 30 days after Buyer’s receipt of the shipment. have no liability for infringement of any patents, trademarks, copyrights,
3. Delivery: Unless otherwise provided on the face hereof, delivery shall be trade dress, trade secrets or similar rights except as provided in this Part
made F.O.B. Seller’s plant. Regardless of the method of delivery, however, 10. Seller will defend and indemnify Buyer against allegations of infringe-
risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. Any de- ment of U.S. patents, U.S. trademarks, copyrights, trade dress and trade
livery dates shown are approximate only and Seller shall have no liability secrets (hereinafter “Intellectual Property Rights”). Seller will defend at its
for any delays in delivery. expense and will pay the cost of any settlement or damages awarded in
4. Warranty: Seller warrants that the items sold hereunder shall be free an action brought against Buyer based on an allegation that an item sold
from defects in material or workmanship for a period of 18 months from pursuant to this contract infringes the Intellectual Property Rights of a third
date of shipment from Parker Hannifin Corporation. THIS WARRANTY party. Seller’s obligation to defend and indemnify Buyer is contingent on
COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO Buyer notifying Seller within ten (10) days after Buyer becomes aware of
ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WAR- such allegations of infringement, and Seller having sole control over the
RANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND WHAT- defense of any allegations or actions including all negotiations for settle-
SOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED ment or compromise. If an item sold hereunder is subject to a claim that
TO, MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER it infringes the Intellectual Property Rights of a third party, Seller may, at
EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE US- its sole expense and option, procure for Buyer the right to continue us-
AGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. ing said item, replace or modify said item so as to make it noninfringing,
or offer to accept return of said item and return the purchase price less
NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES
a reasonable allowance for depreciation. Notwithstanding the foregoing,
WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIAL-
Seller shall have no liability for claims of infringement based on information
LY, TO BUYER’S DESIGN OR SPECIFICATIONS.
provided by Buyer, or directed to items delivered hereunder for which the
5. Limitation of Remedy: SELLER’S LIABILITY ARISING FROM OR IN designs are specified in whole or part by Buyer, or infringements resulting
ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT from the modification, combination or use in a system of any item sold
SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF hereunder. The foregoing provisions of this Part 10 shall constitute Seller’s
THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID BY sole and exclusive liability and Buyer’s sole and exclusive remedy for in-
BUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL SELLER fringement of Intellectual Property Rights.
BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL
If a claim is based on information provided by Buyer or if the design for an
DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING
item delivered hereunder is specified in whole or in part by Buyer, Buyer
BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY
shall defend and indemnify Seller for all costs, expenses or judgements
CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER,
resulting from any claim that such item infringes any patent, trademark,
WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT, EX-
copyright, trade dress, trade secret or any similar right.
PRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT
LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY. 11. Force Majeure: Seller does not assume the risk of and shall not be
liable for delay or failure to perform any of Seller’s obligations by reason
6. Changes, Reschedules and Cancellations: Buyer may request to modi-
of circumstances beyond the reasonable control of Seller (hereinafter
fy the designs or specifications for the items sold hereunder as well as the
“Events of Force Majeure”). Events of Force Majeure shall include without
quantities and delivery dates thereof, or may request to cancel all or part
limitation, accidents, acts of God, strikes or labor disputes, acts, laws,
of this order, however, no such requested modification or cancellation shall
rules or regulations of any government or government agency, fires,
become part of the contract between Buyer and Seller unless accepted
floods, delays or failures in delivery of carriers or suppliers, shortages of
by Seller in a written amendment to this Agreement. Acceptance of any
materials and any other cause beyond Seller’s control.
such requested modification or cancellation shall be at Seller’s discretion,
and shall be upon such terms and conditions as Seller may require. 12. Entire Agreement/Governing Law: The terms and conditions set forth
7. Special Tooling: A tooling charge may be imposed for any special tool- herein, together with any amendments, modifications and any different
ing, including without limitations, dies, fixtures, molds and patterns, ac- terms or conditions expressly accepted by Seller in writing, shall constitute
quired to manufacture items sold pursuant to this contract. Such special the entire Agreement concerning the items sold, and there are no oral or
tooling shall be and remain Seller’s property notwithstanding payment of other representations or agreements which pertain thereto. This Agree-
any charges by Buyer. In no event will Buyer acquire any interest in appa- ment shall be governed in all respects by the law of the State of Ohio. No
ratus belonging to Seller which is utilized in the manufacture of the items actions arising out of sale of the items sold hereunder or this Agreement
sold hereunder, even if such apparatus has been specially converted or may be brought by either party more than two (2) years after the cause
adapted for such manufacture and notwithstanding any charges paid by of action accrues.
Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard
or otherwise dispose of any special tooling or other property in its sole
discretion at any time.

Parker Hannifin Corporation

Pneumatic Division - Asia
82
1002-1/Asia Dec 2010
Parker One Pneumatic

Parker Hannifin Corporation

Pneumatic Division - Asia
83
Parker Worldwide

Europe, Middle East, IE – Ireland, Dublin North America

Africa Tel: +353 (0)1 466 6370
CA – Canada, Milton, Ontario
[email protected]
AE – United Arab Emirates, Tel: +1 905 693 3000
Dubai IT – Italy, Corsico (MI)
Tel: +39 02 45 19 21 US – USA, Cleveland
Tel: +971 4 8127100
[email protected] Tel: +1 216 896 3000
[email protected]
AT – Austria, Wiener Neustadt KZ – Kazakhstan, Almaty
Tel: +43 (0)2622 23501-0 Tel: +7 7272 505 800 Asia Pacific
[email protected] [email protected]
AU – Australia, Castle Hill
AT – Eastern Europe, Wiener NL – The Netherlands, Oldenzaal Tel: +61 (0)2-9634 7777
Neustadt Tel: +31 (0)541 585 000
CN – China, Shanghai
Tel: +43 (0)2622 23501 900 [email protected]
Tel: +86 21 2899 5000
[email protected] NO – Norway, Asker
HK – Hong Kong
AZ – Azerbaijan, Baku Tel: +47 66 75 34 00
Tel: +852 2428 8008
Tel: +994 50 2233 458 [email protected]
[email protected] IN – India, Mumbai
PL – Poland, Warsaw
Tel: +91 22 6513 7081-85
BE/LU – Belgium, Nivelles Tel: +48 (0)22 573 24 00
Tel: +32 (0)67 280 900 [email protected] JP – Japan, Tokyo
[email protected] Tel: +81 (0)3 6408 3901
PT – Portugal, Leca da Palmeira
BY – Belarus, Minsk Tel: +351 22 999 7360 KR – South Korea, Seoul
Tel: +375 17 209 9399 [email protected] Tel: +82 2 559 0400
[email protected] RO – Romania, Bucharest MY – Malaysia, Shah Alam
CH – Switzerland, Etoy Tel: +40 21 252 1382 Tel: +60 3 7849 0800
Tel: +41 (0)21 821 87 00 [email protected] NZ – New Zealand, Mt Wellington
[email protected] RU – Russia, Moscow Tel: +64 9 574 1744
CZ – Czech Republic, Klecany Tel: +7 495 645-2156 SG – Singapore
Tel: +420 284 083 111 [email protected] Tel: +65 6887 6300
[email protected] SE – Sweden, Spånga TH – Thailand, Bangkok
DE – Germany, Kaarst Tel: +46 (0)8 59 79 50 00 Tel: +662 717 8140
Tel: +49 (0)2131 4016 0 [email protected]
[email protected] TW – Taiwan, Taipei
SK – Slovakia, Banská Bystrica Tel: +886 2 2298 8987
DK – Denmark, Ballerup Tel: +421 484 162 252
Tel: +45 43 56 04 00 [email protected]
[email protected] SL – Slovenia, Novo Mesto South America
ES – Spain, Madrid Tel: +386 7 337 6650 AR – Argentina, Buenos Aires
Tel: +34 902 330 001 [email protected] Tel: +54 3327 44 4129
[email protected] TR – Turkey, Istanbul BR – Brazil, Sao Jose dos Campos
FI – Finland, Vantaa Tel: +90 216 4997081 Tel: +55 12 4009 3500
Tel: +358 (0)20 753 2500 [email protected]
[email protected] CL – Chile, Santiago
UA – Ukraine, Kiev Tel: +56 2 623 1216
FR – France, Contamine s/Arve Tel +380 44 494 2731
Tel: +33 (0)4 50 25 80 25 [email protected] MX – Mexico, Apodaca
[email protected] Tel: +52 81 8156 6000
UK – United Kingdom, Warwick
GR – Greece, Athens Tel: +44 (0)1926 317 878 VE – Venezuela, Caracas
Tel: +30 210 933 6450 [email protected] Tel: +58 212 238 5422
[email protected] ZA – South Africa, Kempton Park
HU – Hungary, Budapest Tel: +27 (0)11 961 0700
European Product Information Centre
Tel: +36 1 220 4155 [email protected] Free phone: 00 800 27 27 5374
[email protected] (from AT, BE, CH, CZ, DE, DK, EE, ES, FI,
FR, IE, IL, IS, IT, LU, MT, NL, NO, PL, PT, RU,
SE, SK, UK, ZA)

© 2010 Parker Hannifin Corporation. All rights reserved. 1002-1/KOR Dec 2010

Parker Korea Ltd.

759-10 Geumui-ri, Jangan-myeon,
Hwaseong-si, Gyeonggi-do,
445-941, Korea
Tel: +82 (0) 31-359-0700
Fax: +82 (0) 31-359-0780 Your local authorized Parker distributor
www.parker.com