Scribd
Upload
129 views2 pages

Molar Absorbance Coefficient Calculation

This document describes how to calculate the molar absorbance coefficient (ε) from experimental absorbance and concentration data. It uses data for p-nitrophenol solutions with varying concentrations from 0 to 0.05 mM. Absorbance measurements were taken at 400 nm in a 1 cm cuvette. A graph of absorbance vs. concentration was plotted, and the slope of the line equals εd. The slope was calculated to be 18.2 mM-1, and with a pathlength of 1 cm, ε was determined to be 18.2 mM-1cm-1. However, ε is conventionally reported in M-1cm-1 units, so two methods are described to convert

Uploaded by

Eduardo Garza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
129 views2 pages

Molar Absorbance Coefficient Calculation

This document describes how to calculate the molar absorbance coefficient (ε) from experimental absorbance and concentration data. It uses data for p-nitrophenol solutions with varying concentrations from 0 to 0.05 mM. Absorbance measurements were taken at 400 nm in a 1 cm cuvette. A graph of absorbance vs. concentration was plotted, and the slope of the line equals εd. The slope was calculated to be 18.2 mM-1, and with a pathlength of 1 cm, ε was determined to be 18.2 mM-1cm-1. However, ε is conventionally reported in M-1cm-1 units, so two methods are described to convert

Uploaded by

Eduardo Garza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

3B3: Calculating the molar absorbance coefficient from experimental data

3.B.3. Calculating the molar absorbance coefficient (ε) from absorbance


and concentration data
.
Learning Objective.
To calculate a value for ε from experimental data of absorbance and concentration.
.

In this example we are using data for p-nitrophenol which is a yellow-coloured reagent
commonly used in diagnostic tests (ELISA’s).

p-nitrophenol absorbs well with light of about 400 nm so we measure the absorbance
using light of that wavelength in a cuvette of pathlength 1 cm and call the absorbance A400.
.

plot the data on a graph of A vs C


set up some cuvettes measure the
containing a range of absorbance for each
concentrations of p- cuvette 1
0.9
nitrophenol from 0 to 0.05 mM C (mM) A400
0.8
0.7
0 0 400 0.6
0.5
A
0.01 0.18 0.4
0.3
0.02 0.37 0.2
0.03 0.55 0.1
C (mM) = 0 0.01 0.02 0.03 0.04 0.05 0
0.04 0.72 0 0.01 0.02 0.03 0.04 0.05
0.05 0.91 C (mM)

A = εCd = (εd)C; in a graph of A vs C, the slope is εd.

y2 − y1 0.91 − 0
= 18.2(mM )
−1
slope = ε .d = =
x2 − x1 (0.05 − 0 )mM

d = 1 cm
so

18.2(mM )
−1
18.2(mM )
−1
ε= = = 18.2mM −1cm −1
d 1cm

Creative Commons Attribution Non-commercial Share Alike


Author: Dr Jenny A Koenig Page 1 of 2
3B3: Calculating the molar absorbance coefficient from experimental data

However.... ε is usually written with the units [Link]-1.


How do we get ε in the right units?

Two possible methods:

1
Possibly the easiest way is to start with M rather than mM in the first place.

0.91 − 0
εd =
(0.05 − 0) × 10 −3 M
(
= 18.2 10 −3 M )
−1
= 18.2 × 10 3 M −1 = 18200 M −1

then
ε = 18200 M-1 / 1 cm = 18200 [Link]-1
.

2
Another method is to say
1000 mM = 1 M,
so 1000 mM.M-1 = 1

If ε = 18.2 [Link]-1
then you can multiply both sides by 1 (=1000 mM.M-1)
ε = 18.2 [Link]-1 x 1000 mM.M-1

then the mM-1 cancels with the mM


ε = 18.2 [Link]-1 x 1000 mM.M-1

and you are left with


ε = 18200 M-1cm-1
.

Creative Commons Attribution Non-commercial Share Alike


Author: Dr Jenny A Koenig Page 2 of 2

You might also like