DigiTemp-E Wireless
Temperature measurement
in molten metals
DigiTemp-E Wireless
Temperature measurement in molten metals
Temperature measurement using wireless transmission
With DigiTemp-E Wireless you can receive the temperature
measurement results wirelessly.
Located near the handle of the optional QUBE measurement lance
is the QUBE T battery-powered wireless transmission module,
which transfers the temperature measurement data directly to the
DigiTemp-E Wireless instrument.
Up to 1000 measurements can be taken using the QUBE T with its
long-life lithium ion batteries. The batteries are charged using the
dedicated charging station.
Safety-related benefits
Q no cables lying around
Q no repairs in security restricted and hazardous environments
DigiTemp-E Wireless
Cost-relevant advantages
Q no wiring or cable connection between the submersible
measuring probe and measuring instrument
The ever-increasing demands on measurement technology require
the integration of new electronics hardware, interfaces, and in Q no attachment of cable conduit/terminal blocks
particular the software.
The innovative DigiTemp-E Wireless instrument fully meets these
expectations. Its features are reliability, ease of use, and flexibility
in application.
The DigiTemp-E Wireless measures and analyzes the temperature
in steel, iron, and non-ferrous melts. Sensors are connected to the
instrument through wired lances or with manually operated QUBE
wireless lances.
2
3
QUBE T
1: QUBE T transmitter
2: QUBE T handle
3: QUBE T battery and charging station
The functional operation of the instrument is easy and
fully automated and also features:
Q password-protected device configuration using an internal LCD
and buttons; and
Q backup and restore of the instrument parameters using an
integrated and removable memory.
You can set instrument parameters and select data
telegrams using an LCD interface inside the instrument.
The parameterization is password protected, so that only author-
ized personnel can perform this task. Parameters can be set for:
Q evaluation tolerances;
Q thermocouple calibration type;
Q measurement times;
Q data Interfaces;
Q start conditions;
Q calibration offset; and
Standard features of Q bath level.
the DigiTemp-E Wireless You can also set instrument configuration parameters
using a web browser.
Q wireless receiver for the QUBE T wireless measurement lance
The DigiTemp-E Wireless has three user-oriented data
Q non-reflecting 45mm display with wireless connection and
interfaces and four control outputs as standard.
signal strength indication
Q LED measurement sequence signals
Q high measurement accuracy by high-resolution A/D converter
Q universal application using a wide range power supply
Standard interfaces and outputs
Q measurement data output using a V24 interface or serial
Q curves for thermocouple types S, R, B, K and D
TTY 20mA interface for PLC and peripheral devices;
Q measurement error detection and interpretation
Q mA output with follow mode;
Q automatic test measuring recognition
Q Ethernet interface;
Q four pre-programmed data telegrams, three additional data
Q bath level;
telegrams freely programmable using Ethernet
Q wireless receiver unit; and
Q control outputs for signalisation and PLC.
In addition to the conventional immersion temperature
measurement in molten steel, the DigiTemp-E Wireless
can be adapted for other measurement tasks in molten
steel.
This is done by using a menu inside the instrument to set
parameters for different measurement sensors used for
immersion temperature measurements in:
Q steel, iron, and non-ferrous melts with Positherm®
disposable probes;
Q iron melts with Multi-Stik® reusable probes; and
Q non-ferrous metal and aluminium.
The standard Ethernet interface and the optional fieldbus
interfaces allow the equipment to operate on the network.
The instrument can detect bath level in molten steel and iron
when in wired operation. This is done using our Positherm®
immersion thermocouple connected to an automatic lance.
Machine-specific installations are not needed with this method
of bath level detection.
Option for one extension module
Q second serial TTY 20 mA interface, or
Q Profibus DP, or
Q Profinet IO, or
Q Modbus RTU, or
Q Modbus TCP, or
Q Ethernet IP, or
Q two-channel mA output, or
Q second V24 interface
DigiTemp-E Wireless with standard interfaces and optional interfaces
Wired Wireless
Transmission Transmission
PLC
Ethernet
DigiTemp-E Wireless
Profibus DP, or
Profinet IO, or
Modbus RTU, or
Modbus TCP, or
Ethernet IP
serial interface serial interface
Analogue output
Signalisation PLC
Signalisation
Signalisation Ethernet
Standard Interface Optional Interface
MeltControl 2020 software
The DigiTemp-E Wireless instruments can be networked with a PC DigiTemp-E Wireless instrument parameters can also be set
using an Ethernet interface. using MeltControl 2020.
With the measurement data software installed on the PC, you can MeltControl 2020 is a server application and can be used with
remotely analyse and save the measurement sequences, results, Windows® 7.
and curves of the DigiTemp-E Wireless instrument.
MeltControl 2020 Software: Measurement data system
Client PC stations
Server PC
Ethernet
DigiTemp
DigiTemp-E
p-E DigiTem
DigiTemp-E
mpp-E DigiTem
DigiTemp-E
mpp-E DigiTem
DigiTemp-E
mp-E
Wireless
Wireles
ss Wireless
Wirele
esss Wireless
Wirele
esss Wireless
Wirele
ess
Microsoft Windows® 7 is a registered trademark of the Microsoft Corporation.
Technical data
DigiTemp-E Wireless
Measurement application dip-temperature continuous temperature measurement application se-
measurement measurement lected on the internal LCD
bath level detection only in wired operation
Measurement input 1 analog input channel galvanically isolated
Measurement rate 10 samples/second
Input range temperature: type S: 200°C to 1760°C arithmetically linearised accord-
type R: 200°C to 1760°C ing to IEC 584, IPTS68, IPTS48,
type B: 200°C to 1820°C or ITS90
type K: 200°C to 1370°C
type D: 200°C to 2300°C according to ASTME 988
Accuracy temperature ±1°C at 0°C to 50°C ambient in measurement range > 400°C
temperature
Temperature plateau plateau length window height
detection 0.1s to 5s, 0.2°C to 10°C,
adjustable in 0.1s steps adjustable in 0.1°C steps
Measurement circuit automatic thermocouple automatic sensor
monitoring break detection recognition
Offset adjustment ±5°C
Start conditions temperature
200°C to 1200°C,
adjustable in 50°C steps
Maximum measurement 6s to 60s selectable
time
Trace analysis plateau query with error
measurement interpretation
Display 4-digit 7-segment LED, matrix display for wireless T °C or T °F
45mm digit heigh signal and battery strength optional heat number input board
Temperature display in °C or °F
Display resolution 1°C/1°F 4-digit display with floating
decimal point
Measurement sequence ready, measure, complete green, yellow, and red LEDs
display
Signal outputs four potential-free PhotoMOS maximum 250V AC/DC, status signals also available using
solid state relays with two maximum 500mA, serial communication ports TTY,
common 500mA FF fuses: maximum 60W/VA Ethernet, Profibus (optional)
one for horn and one for
measurement sequence
(green, yellow, red).
Standard data outputs TTY 20mA, serial, protocol: CTS, 3964, or no protocol
or V24 interface 3964R, STX ETX BCC,
STX BCC ETX
Ethernet TCP/IP Client Server
mA output 0/4-20mA
bath level detection ’Horn’ contact only for wired operation with
autolances
Additional interfaces/options second serial TTY
20 mA interface, or
second V24 interface, or
Profibus DP, or
Profinet IO, or
Modbus RTU, or
Modbus TCP, or
Ethernet IP interface, or
mA output 0/4-20mA 2-channel
Data telegrams four selectable and three programmable using a web
freely programmable browser
Housing, dimensions, metal housing for IP 55 protection, dimensions: H=230mm,
and weight wall mounting, coating RAL 9005 W=260mm, D=150mm
weight: approx. 7.5kg
Operating data power supply 90 to 264V AC, power consumption ambient temperature
47 to 63Hz maximum 34VA 0 to +50°C
QUBE T 2
1. QUBE T Transmitter
Measurement application temperature, oxygen, and carbon measurements
Transmission 2.4GHz antenna installed inside the
housing
Input range type S, R, B, K, D arithmetically linearised
according to IPTS68, IPTS48
or ITS90
Displays built-in display for measurement place selectable or programmable
using pushbutton
Housing interlock for display and battery IP 65 protection
2. QUBE Handle
Design ergonomic design with molded, rubber grip
3. Battery and charging station
Battery long-life lithium ion built-in fuel gauge, rechargeable
up to 1000 measurements possible
Charging station fast charge with feedback LEDs and
self-cleaning blade contacts
Further technical details on request, deviations from illustrations and technical data indicated reserved.
WM-No.: H-EN-DTE-0400-01-15 E
Heraeus Electro-Nite GmbH & Co. KG Heraeus Electro-Nite International N.V.
Unter dem Hofe 10 Centrum Zuid 1105
58099 Hagen (D) 3530 Houthalen (B)
Tel. +49(0)6181.352700 Tel. +32(0)11.600211
Fax +49(0)6181.352800 Fax +32(0)11.600400
[email protected] [email protected] Certified Quality System
www.heraeus-electro-nite.com www.heraeus-electro-nite.com DIN EN ISO 9001:2008
