Methods and estimation of excess

rainfall (runoff )- Theory and Practical

Dr. Ranu Rani Sethi

Principal Scientist
ICAR-Indian Institute of Water Management
Bhubaneswar, Odisha
 Outline
• Runoff and factors affecting runoff

• Estimation of Runoff
Rational formula
Curve Number method
Use of remote sensing and GIS

• Runoff measuring devices

Direct Discharge Methods

Weirs
Orifices
Flumes

Velocity - Area Methods

Float method
Current meter
 Runoff
Portion of precipitation that makes its way towards
streams, lakes or oceans as surface or
subsurface flow

Factors affecting runoff

Climatic factors
Physiographic factors
 Runoff measurement methods

Rational Method

Where,

Q =Peak rate of runoff, m3/sec;

I =Intensity of rainfall, mm/hour (time of concentration)
C =runoff coefficient
A =Area of the catchment, ha
Runoff coefficient (C)
Sl Soil type Land use
No.
Cultivation Pasture Forest
1 Soil with above 0.29 0.15 0.1
average infiltration
rate i.e. sandy or
gravel
2 Soil with average 0.4 0.35 0.3
infiltration rate, no
clay pans, loams and
similar soil
3 Soil with below 0.5 0.45 0.4
average infiltration
rates, heavy clay soils
or soils with a clay
pan near the surface,
shallow soils above
impervious rock
 Intensity of rainfall (I)

I calculated for the period equal to the time

of concentration of the catchment.

The Time of Concentration (Tc) is defined as

the time required for water flow from the
most remote point of the catchment to the
outlet
 Time of Concentration (Tc)
• This is the longest time it takes
for a part of the catchment to
contribute water to the outlet.

• It is the time it takes for all the

parts of the watershed to be
contributing water to the outlet.

• The divide or watershed

divides the flow of water along
different slopes.

• All runoffs flow from the whole

catchment to the stream or Where,
outlet. tc =Time of concentration, min;
L =Length of channel reach, m;
S =average slope of the channel reach, m/m
 Limitations

• It assumes that rainfall intensity is uniform over

the entire watershed during the duration of the
storm, which is very rare

• The initial losses due to depression storage and

initial infiltration are not considered.

• Runoff coefficient changes with respect to

season as well as rainfall characteristics, which
is not considered in rational formula
 Curve number method

Where,

F =Actual retention, mm;

S =Potential maximum retention, mm;
Q =accumulated runoff depth, mm;
P =accumulated rainfall depth, mm
Ia =Initial abstraction, mm
Factors determining curve number
values

Indicate runoff response characteristics of the

drainage basin.

Parameters like land use, land treatment,

hydrological condition, hydrological soil group
and antecedent soil moisture condition in the
drainage basin are related to curve number
values.
Estimation of runoff by using remote
sensing and GIS
Preparation of Land
use/Land cover map by
using the remote sensing
and GIS.
Preparation of hydrologic
soil group map for making
appropriate hydrological soil
classification A, B, C & D
Decide the curve number
(CN) values based on field
condition.
Calculate S value and then
estimate runoff Q
 Estimation of runoff depth -Example

Preparation of Various Thematic Maps:

Kanhaiya nala watershed
1. Contour map
2. Drainage map
In Tons River catchment
3. DEM
Elevation - 480 to 620 m above MSL
4. Slope map
Satna District (M.P.)
5. Land land use/ land cover map.
Soil and Land use land cover
Generating CN and runoff depth map
 Runoff measuring devices

Direct Discharge Methods

Weirs
Orifices
Flumes

Velocity - Area Methods

Float method
Current meter
Tracer method
 Weir
Q = C L Hm

Where,
Q = discharge;
C = coefficient dependent on
the nature of weir crest and
approach conditions; Rectangular weir with no end contraction
L = length of crest;
H = head on the crest
m = exponent depending on
weir opening. Rectangular weir with two end contraction

Weirs should be calibrated to

determine these
parameters before use.
 Orifice

Where,
Q = discharge rate, l/sec;
C = coefficient of discharge
(0.6 - 0.8);
a = area of the orifice opening,
sq cm;
g = acceleration due to gravity,
cm/s2
h = head of water causing the
flow, cm
 Flumes
Parshal Flumes

Used under free flow and submerged

flow condition.

The single, primary point of

measurement, denoted as Ha,
which determine the flow rate
through the flume.

In short throated flume, the Ha is

upstream of the throat at a specific
location - 2/3 of the sidewall length
as measurement back from where
the converging section meets the
throat

For large Parshall flumes the point of

measurement is closer to the throat
 Standard design dimensions
(from USDA-SCS 1965)
Throat A (feet, B C D
width inches)
W
(feet)
1 3-0 4-4 7/8 2-0 2-9 1/4
1½ 3-2 4-7 7/8 2-6 3-4 3/8
2 3-4 4-10 7/8 3-0 3-11½
3 3-8 5-4 3/4 4-0 5-1 7/8
4 4-0 5-10 5/8 5-0 6-4 1/4
5 4-4 6-4½ 6-0 7-6 5/8
6 4-8 6-10 3/8 7-0 8-9
7 5-0 7-4½ 8-0 9-11 3/8
8 5-4 7-10 1/8 9-0 11-1 3/4

Dimension A = 2/3 (w/2 + 4)

 Cut Throat Flume
Improved version of Parshal
flume.

It is having flat bottom,

vertical wall and no throat
section.

For free flow critical depth is

measured at throat.

Free flow depends on flume

size and submergence ratio.
Stream flow monitoring methods

The volume of water that Step 1: Selecting the

moves through the channel channel location
is then calculated by
dividing the channel into Step 2: Developing a cross-
smaller units of known or section of the site and
approximated areas (width establishing a reference or
× depth) staff gauge
Measuring the flow within Step 3: Measuring interval
each area (velocity - and depth
distance over time).

By multiplying area and

velocity, flow is calculated
from the location
 Measurement of stream flow
discharge
Mid section method
Velocity-area method
 Float Method

• A floating object is put in

water and time is recorded to
cover a known distance.

• Assuming the float travels ‘D’

meters in ‘t’ seconds

• Velocity of water at surface =

(D/t) m/s,

• Average velocity of flow = 0.8

(D/t),

Flow rate, Q = Cross

sectional area × velocity of
flow
 Current meter
Current meter is a small
instrument containing a
revolving wheel or vane that is
turned by the movement of
water.

Current meter is inserted to the

depth = 0.6 d (d = depth of
flow).

Number of rotations (rpm) was

recorded and then velocity of
flow is calculated from
calibrated chart.

A current meter is used to

measure velocity at 0.2 and 0.8
depth or at only 0.6 depth.
 Stage level recorder

• Non recording stream gage

Staff
Wire(String)
Crest staff

• Recording stream gage

Float type
Digital gage
 Measurement of discharge in Sunity Creek
Sl. Distance Av. Measured Top Bottom Water Area, Discharge,
No from Count/ Velocity, width, width, depth, (A) Q
mouth, minute
m m sec-1 m m m m2 m3 sec-1
1 60 80 0.40 40.00 38.80 0.40 15.76 6.33
2 120 80 0.40 60.00 59.10 0.30 17.87 7.12
3 180 71 0.36 50.00 49.10 0.30 14.87 5.28
4 240 78 0.39 50.00 49.04 0.32 15.85 6.21
5 300 80 0.40 51.00 50.10 0.30 15.17 6.09
6 360 80 0.40 42.00 41.04 0.32 13.29 5.34
7 420 82 0.41 46.00 45.07 0.31 14.12 5.79
8 480 80 0.40 49.00 48.10 0.30 14.57 5.80
9 540 82 0.41 40.00 38.92 0.36 14.21 5.83
10 600 76 0.38 53.00 52.04 0.32 16.81 6.36
11 660 77 0.39 38.00 36.86 0.38 14.22 5.48
12 720 67 0.34 55.00 54.10 0.30 16.37 5.51
13 780 63 0.32 71.00 70.28 0.24 16.95 5.29
14 840 65 0.33 63.00 62.25 0.25 15.66 5.09
15 900 56 0.28 61.00 60.13 0.29 17.56 4.89
16 960 44 0.22 52.00 51.16 0.28 14.44 3.20
17 1020 36 0.18 63.00 62.16 0.28 17.52 3.18
18 1080 44 0.22 92.00 91.40 0.20 18.34 2.63
19 1140 40 0.20 40.00 39.16 0.28 11.08 2.22
20 1200 39 0.20 52.00 51.10 0.30 15.47 3.04
21 1260 34 0.17 49.00 48.22 0.26 12.64 2.17
22 1320 35 0.17 47.00 46.10 0.30 13.97 2.42
23 1380 73 0.37 47.00 46.04 0.32 14.89 5.46
24 1440 65 0.33 49.00 48.10 0.30 14.57 4.73
25 1500 57 0.29 58.00 57.25 0.25 14.41 4.11
26 1560 57 0.28 44.00 43.16 0.28 12.20 3.46
27 1620 48 0.24 42.00 41.13 0.29 12.05 2.89
28 1680 62 0.31 37.00 36.10 0.30 10.97 3.38
29 1740 65 0.32 41.00 40.04 0.32 12.97 4.19
30 1800 77 0.38 31.00 29.92 0.36 10.97 4.20
31 1860 66 0.33 32.00 30.86 0.38 11.94 3.96
32 1920 62 0.31 30.00 28.80 0.40 11.76 3.65
33 1980 74 0.37 34.00 32.80 0.40 13.36 4.97
34 2040 63 0.32 30.00 28.80 0.40 11.76 3.70
 Water availability in creeks and water quality
Creek Discharge at Volume of
creek cross Water available
section (November -
( m3/sec) January),
m3
Creek Q1 11.03
Creek Q2 9.35
Creek Q3 7.84
Creek Q4 7.04
Average 8.81 31474958
(Creeks)
Sub Creek 10.5
Q1
Sub Creek 5.87
Q2
Sub Creek 4.73
Q3
Sub Creek 4.42
Q4
Average 6.38 22324896
(Sub creeks)
Total 53799854
 References
Estimating discharge and stream flows a guide for sand and gravel
operators (July 2005 Ecology Publication Number 05-10-070)
Murty, V.V.N. and Jha, M.K.2013. Land and Water Management
Engineering.
https://www.lmnoeng.com/Hydrology/rational.php
Ritzema, H.P., Drainage Principles and application. ILRI Publication 16,
Second edition.
Raghunath, H.M.,1985. Hydrology Principles, Analysis and Design

THANK YOU