Scribd
Upload
152 views

Lec 4

1) The document discusses methods for calculating the energy required to crush materials of different initial and final sizes using Rittinger's law and Kick's law. 2) It also examines the surface area produced when materials are ground and crushed, noting that the specific surface area is important for many material properties and reactions. 3) An example calculation is shown to estimate the surface areas of two particle size fractions from a salt sample using sieving data and assumptions about particle shape and density.

Uploaded by

Ghazy alshyal
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
152 views

Lec 4

1) The document discusses methods for calculating the energy required to crush materials of different initial and final sizes using Rittinger's law and Kick's law. 2) It also examines the surface area produced when materials are ground and crushed, noting that the specific surface area is important for many material properties and reactions. 3) An example calculation is shown to estimate the surface areas of two particle size fractions from a salt sample using sieving data and assumptions about particle shape and density.

Uploaded by

Ghazy alshyal
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Unit OperatiOn

Example 2 :

A material is crushed in a Blake jaw crusher such that the


average size of particle is reduced from 50 mm to 10 mm with
the consumption of energy of 13.0 kW/(kg/s). What would be
the consumption of energy needed to crush the same material of
average size 75 mm to an average size of 25 mm :
a) assuming Rittinger’s law applies?
b) assuming Kick’s law applies?
Which of these results would be regarded as being more reliable
and why ?

Solution
a) Rittinger’s law.
This is given by:
E = KRfc[(1/L2) − (1/L1)]
Thus : 13.0= KRfc [(1/10) − (1/50)]
and: KRfc = (13.0 × 50/4) = 162.5 kW/(kg mm)
Thus the energy required to crush 75 mm material to 25 mm is:
E = 162.5[(1/25) − (1/75)] = 4.33 kJ/kg
b) Kick’s law.
This is given by:
E = KKfc ln(L1/L2)
Thus: 13.0 = KKfc ln(50/10)
And : KKfc = (13.0/1.609) = 8/08 kW/(kg/s)
Thus the energy required to crush 75 mm material to 25 mm is:
E = 8.08 ln(75/25) = 8.88 kJ/kg

Lecturer . Shymaa Ali Hameed 2013-2014


Unit OperatiOn
The size range involved by be considered as that for coarse
crushing and, because Kick’s law more closely relates the
energy required to effect elastic deformation before fracture
occurs , this would be taken as given the more reliable result .
3. Surface Area Formed by Grinding
When a uniform particle is crushed , after the first crushing the
size of the particles produced will vary a great deal from
relatively coarse to fine and even to dust. As the grinding
continues, the coarser particles will be further reduced but there
will be less change in the size of the fine particles. Careful
analysis has shown that there tends to be a certain size that
increases in its relative proportions in the mixture and which
soon becomes the predominant size fraction .

The new surface produced was directly proportional to the


energy input. For a given energy input the new surface produced
was independent of :
(a) The velocity of impact ,
(b) The mass and arrangement of the sample ,
(c) The initial particle size , and
(d) The moisture content of the sample .
For example , wheat after first crushing gives a wide range of
particle sizes in the coarse flour, but after further grinding the
predominant fraction soon becomes Most reactions are related to
the surface area available, so the surface area can have a
considerable bearing on the properties of the material. The
surface area per unit mass is called the specific surface. To

Lecturer . Shymaa Ali Hameed 2013-2014


Unit OperatiOn
calculate this in a known mass of material it is necessary to
know :
• the particle-size distribution
• the shape factor of the particles.
The particle size gives one dimension that can be called the
Typical Dimension, Dp of a particle. This has now to be related
to the surface area. We can write, arbitrarily:
= =6

Where
Vp is the volume of the particle.
Ap is the area of the particle surface
Dp is the typical dimension of the particle
q is factor of the particle geometries.
And , The ratio of surface area to volume is:
⁄ = (6 ⁄ ) =6 ⁄

=6 ⁄

λ=q/p is a shape factor . It has been found, experimentally


For example ,

Specific Surface
Vp Ap Vp/ Ap
λ
Cube Dp3 6Dp2 6/Dp 1
Sphere /6 6/Dp 1

Lecturer . Shymaa Ali Hameed 2013-2014


Unit OperatiOn
A number of particles(N) is :

= =

Where :
m is a total mass of particles
mp is a mass of particle
ρp is a density of particles
So total area of the mass of particles (At) is:

= =

Example 3 :
In an analysis of ground salt using Tyler sieves, it was found
that 38% of the total salt passed through a 7-mesh sieve and was
caught on a 9-mesh sieve. For one of the finer fractions, 5%
passed an 80-mesh sieve but was retained on a 115-mesh sieve.
Estimate the surface areas of these two fractions in a 5 kg
sample of the salt, if the density of salt is 1050 kg/m3 and the
shape factor is 1.75.
Aperture of Tyler sieves ,
7 mesh = 2.83 mm
9 mesh = 2.00 mm
80 mesh = 0.177 mm
115 mesh = 0.125 mm .

Lecturer . Shymaa Ali Hameed 2013-2014


Unit OperatiOn
Solution :
Mean aperture 7 and 9 mesh = 2.41 mm = 2.4 x 10-3m
Mean aperture 80 and 115 mesh = 0.151 mm = 0.151 x 10-3m
At = (6 x 1.75 x0.38 x 5)/(1050x 2.41x10-3)
At = 7.88 m2
At = (6 x 1.75x 0.05 x 5)/( 1050 x 0.151x10-3)
At = 16.6 m2.

Lecturer . Shymaa Ali Hameed 2013-2014

You might also like