Scribd
Upload
135 views

LEOXFER LEOMATIc

This document contains error codes and descriptions for an automation system. It includes 3 sections: error codes for monitoring errors, dialog box text for the error monitoring program, and default error descriptions for system errors and PLC errors. The error codes range from 000 to 124 and include descriptions of issues like communication timeouts, hardware limits, invalid data, and program errors.

Uploaded by

Josué T Silveira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
135 views

LEOXFER LEOMATIc

This document contains error codes and descriptions for an automation system. It includes 3 sections: error codes for monitoring errors, dialog box text for the error monitoring program, and default error descriptions for system errors and PLC errors. The error codes range from 000 to 124 and include descriptions of issues like communication timeouts, hardware limits, invalid data, and program errors.

Uploaded by

Josué T Silveira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

;=========================== LeoXMonErr3020 - ITALIANO

=============================

; CLeoXMonErr30Ctrl
[00]
|000" P N C O K : N O E R R O R D E T E C T E D"
|001"OK : no errors detected"
|002" P N C F A I L U R E : E R R O R S D E T E C T E D"
|003"FAILURE : there are "
|004" ERRORS !"
|005"FAILURE : there is "
|006" ERROR !"
|007" ** "
|008" -> "
|009"ERROR ON , "
|010"ERROR OFF, "
|011"Unable to write on file "
|012"LeoXMonErr30.ocx"
|013"Pnc Monitoring OFF!"
|014"Pnc Monitoring ON..."
|015"System Error "
|016" (No description)"
|017"Plc Error "
|018" (No description)"
|019"Communication Error"
|020"SYS Error = "
|021"PLC Error = "
|022"COM Error = "
|023"Monitoring Errors Failure: Serial Port Is OFFLINE!"
|024"Monitoring Errors Failure: Communication Error With Pnc!"
|025"Monitoring Errors Failure: Configuration Error!"
|026"Monitoring Errors Failure: Ask Error!"
|027"PNC"
|028" - "

; CLeoXMonErr30Dlg
[01]
|000"Less info..."
|001"More info..."
|002"More info..."
|003"Clear Errors"
|004"About ..."
|005"Exit"
|006"No Active!"

; CDialogSysEr
[02]
|000"Nr"
|001"Identifier"
|002"Description""
|003"Set System Error Strings to Default?"
|004"LeoXMonErr30"

;m_strDefaultErDescr
[04]
; "0123456789012345678901234567890123456789"
|000"GENERIC Error on Axis Card "
|001"Sample Time Too Small on Axis Card "
|002"Intercard Link Error on Axis Card "
|003"Max Position Pid Error on Axis "
|004"Pid Out Saturation on Axis "
|005"Forward Software Limit on Axis "
|006"Backward Software Limit on Axis "
|010"Communication Time-Out on Axis Card "
|011"Init Error: Can't Find Axis Card "
|012"Init Error: Safety Mode on Axis Card "
|013"Forward Hardware Switch Limit on Axis "
|014"Backward Hardware Switch Limit on Axis "
|015"Movements Disabled on Axis "
|016"Card Not Configurated for Axis "
|017"Firmware Too Old on Axis "
|018"Invalid Electronic Cam Table "
;
|020"Communication Time-Out on A/D Card "
|021"Init Error: Can't Find A/D Card "
|022"Init Error: Safety Mode on A/D Card "
|023"Communication Time-Out on CAN Card "
;
|025"Communication Time-Out on CAM Card "
|026"No Communication Protocol on CAM Card "
;
|030"Data Open Error On Flash Page "
|031"Data Read Error On Flash Page "
|032"Data Write Error On Flash Page "
|033"Data Clear Error On Flash Page "
|034"Data Version Error On Flash Page "
|035"Configuration Data Lost: Default Loaded "
|036"Recipes Data Lost: Default Loaded "
|037"Plc Program Lost: Empty Program Loaded "
|038"Plc ER string lost: Default Loaded "
|039"Cmos Data Lost: Loaded From Flash Page "
;
|040"Plc Program Not Enabled "
|041"Plc Program Execute Unknown Command "
;
|047"Firmware Update Error: Can't Find Card "
|048"Firmware Update Error: Retry On Card "
;
|050"Checksum Flash Error: Cycle Lost "
|051"Checksum Cmos Error: Cycle Lost "
|052"Write On Not Open Cycle "
|053"Write Denied On Cycle "
|054"Write On Not Empty Cycle "
|055"Write Flash Error on Cycle "
|056"Write Memory Full on Cycle "
|057"Read On Not Open Cycle "
|058"Read Denied on Cycle "
|059"Read Empty on Cycle "
|060"Read Flash Error on Cycle "
|061"Clear Flash Error on Cycle "
|062"Can't Execute Disabled Cycle "
|063"Undefined Instruction on Cicle "
;
|070"Cnc Not Ready "
|071"Cnc Queue Is Full "
|072"Undefined Cnc Instruction "
|075"Calibration On Disabled Axis "
|076"Start Jog On Disabled Axis "
|077"Start Goto On Disabled Axis "
|078"Goto Out Of Forward Limit "
|079"Goto Out Of Backward Limit "
|080"Interp On Too Many Axis "
|081"Interp On Axis With Bad Configuration "
|082"Interp On Disabled Axis "
|083"Interp Lin Forward Limit "
|084"Interp Lin Backward Limit "
|085"Interp Arc Forward Limit "
|086"Interp Arc Backward Limit "
|087"Interp Arc Center Error "
|088"Interp Arc Radius Error "
|089"Interp Max Err Time Out "
|090"Start Cam Error "
|091"Start Follower Error "
|100"Wait Mask Parameters Error "
|101"Wait Mask Time out Error "
|102"Wait Value Parameters Error "
|103"Wait Value Time out Error "
|104"Set Var Parameters Error "
|105"Set Var Parameters Error "
|106"Set Var Parameters Error "
|107"Set Mask Parameters Error "
;
|120"Cpu Unknown Exception on Task "
|121"Cpu Math Division by Zero on Task "
|122"Cpu Math Overflow on Task "
|123"Cpu Unused Opcode on Task "
|124"Cpu Data Overflow on Page "

; CDialogPlcEr
[05]
|000"Nr"
|001"Identifier"
|002"Description""
|003"Clear Plc Error Strings?"
|004"LeoXMonErr30"
|005"PLC_ER_"

You might also like