ERBE

ERBOTOM ICC 350

Instruction manual
08.00
 ERBOTOM ICC 350 V 4.X
10128-016, 10128-061, 10128-300, 10128-301, 10128-025,10128-402

ERBOTOM ICC 350 Z V 2.X

10128-065

ERBOTOM ICC 350 T V 2.X

10128-066

ERBOTOM ICC 350 M V 4.X

10128-080, 10128-083

ERBOTOM ICC 350 M-DOKU V 4.X

10128-081

Instruction manual
08.00
 ISO 9001
EN 46001

All rights to this instruction manual, particularly the right to reproduction, distribution and translation, are reserved.
No part of this instruction manual may be reproduced in any form (including photocopying, microfilm or other
means), or processed, reproduced or distributed by means of electronic systems without prior written permission
from ERBE ELEKTROMEDIZIN GmbH.
The information contained in this instruction manual may be revised or extended without prior notice and represents
no obligation on the part of ERBE ELEKTROMEDIZIN GmbH.

© ERBE ELEKTROMEDIZIN GmbH, Tübingen 2000

Printed by: ERBE ELEKTROMEDIZIN, Tübingen Instruction manual No. 80104-301

Chapter Title Page

1 INTRODUCTION................................................................ 1-1
1.1 Intended purpose of the ICC 350 ................................................ 1-1
1.2 How do I work with this instruction manual? ............................. 1-1
1.3 Explanation of the safety instructions ......................................... 1-1

2 INITIAL OPERATION ........................................................ 2-1

3 RISKS AND SAFETY

OF HIGH-FREQUENCY SURGERY .................................. 3-1
3.1 Unintentional thermal tissue damage .......................................... 3-1
3.1.1 - due to HF leakage currents ....................................................... 3-1
3.1.2 - due to unintentional activation of an HF generator ................... 3-2
3.1.3 - due to inappropriate application ................................................ 3-3
3.1.4 - due to inappropriate or nonapplication of
the neutral electrode .................................................................... 3-3
3.1.5 - due to unsuitable and/or faulty accessories ............................... 3-4
3.1.6 - due to inattentiveness ................................................................ 3-5
3.1.7 - due to an output error ................................................................ 3-5
3.1.8 - due to the ignition of flammable liquids, gases
and/or vapors ............................................................................... 3-5
3.1.9 Unintentional burns due to hot electrodes ................................... 3-6
3.2 Electric shock .............................................................................. 3-6
3.3 Stimulation of nerves and muscles .............................................. 3-6
3.4 Cardiac pacemaker ...................................................................... 3-7
3.5 Danger of explosion .................................................................... 3-7
3.6 Interference with other electronic equipment .............................. 3-7

4 DESCRIPTION OF THE HIGH-FREQUENCY

SURGICAL UNIT ............................................................... 4-1
4.1 General description ..................................................................... 4-1
4.2 Description of the controls .......................................................... 4-4
1 Power switch .......................................................................................... 4-4
2 AUTO CUT function field ..................................................................... 4-5
3 AUTO COAG 1 function field ............................................................... 4-6
4 AUTO COAG 2 function field ............................................................... 4-7
5 AUTO BIPOLAR function field ............................................................ 4-8
6 Working with programs ......................................................................... 4-9
7 Connecting socket for neutral electrodes ............................................. 4-12
8 Connecting socket for the AUTO CUT and AUTO COAG 1
function fields ...................................................................................... 4-12
9 Connecting socket for the the AUTO CUT and AUTO COAG 2
function fields ...................................................................................... 4-12
10 Connecting socket for the AUTO BIPOLAR function field ................ 4-13
11 Safety field ........................................................................................... 4-13
12 Connecting socket for a dual-pedal footswitch .................................... 4-13
13 Connecting socket for a single-pedal footswitch ................................. 4-13
14 Terminal for potential equalization ...................................................... 4-14
15 Volume for acoustic signals ................................................................. 4-14
16 Loudspeaker for acoustic signals ......................................................... 4-14
17 Power connection ................................................................................. 4-14
18 Power fuses .......................................................................................... 4-14
4.3 Description of the safety features .............................................. 4-14
 5 ERBOTOM ICC 350 Z ....................................................... 5-1

6 ERBOTOM ICC 350 T ....................................................... 6-1

7 ERBOTOM ICC 350 M ....................................................... 7-1

8 ERBOTOM ICC 350 M-DOKU ........................................... 8-1

9 TECHNICAL DATA, SIGNALS, DIAGRAMS..................... 9-1

9.1 Technical data .............................................................................. 9-1
9.2 Visual and acoustic signals .......................................................... 9-5
9.3 Diagrams ..................................................................................... 9-6

10 INSTALLATION ............................................................... 10-1

11 CLEANING AND DISINFECTION OF THE UNIT ............ 11-1

12 PERFORMANCE CHECKS ............................................. 12-1

12.1 Automatic performance test after starting up the unit ............... 12-1
12.2 Automatic performance check during activation ...................... 12-1
12.3 Automatic error documentation ................................................. 12-2
Error list ..................................................................................... 12-3

13 SAFETY CHECKS ........................................................... 13-1

14 MAINTENANCE, CARE, DISPOSAL .............................. 14-1

15 GUARANTEE .................................................................. 15-1

ADDRESSES
1 INTRODUCTION

1.1 Intended purpose of the ICC 350

The ICC 350 is a high-frequency surgical unit for cutting and coagulation. Due to its performance
features, it has universal applications. To meet the special requirements of surgical specialty
fields, the ICC 350 is available in several versions.

1.2 How do I work with this instruction manual?

Please read the instruction manual for the ICC 350. It applies to all versions of this high-frequency
surgical unit. If you have an ICC 350 Z, for example, please additionally read the chapter ICC
350 Z.

1.3 Explanation of the safety instructions

The WARNING safety instruction indicates a danger which can result in personal injury.

The CAUTION safety instruction indicates a danger which can result in property damage.

The IMPORTANT safety instruction indicates a danger which can cause functional failure of the
unit.

1-1
1-2
2 INITIAL OPERATION

Read carefully before initial operation of the unit.

In the development and production of this high-frequency surgical unit, the relevant, generally
recognized rules of technology, as well as the valid occupational safety and accident prevention
regulations have been taken into consideration. This ensures that patients, employees and third
parties are protected from dangers to life and health during intended application of the high-
frequency surgical unit, to the extent permitted by the type of application intended.

Initial operation
Before delivery, every high-frequency surgical unit is tested by the manufacturer in regard to its
function and safety. To ensure that the unit also functions safely after shipping and installation at
the operator’s site, the following points should be observed:

The operator should only operate the high-frequency surgical unit if the manufacturer or supplier

1. has subjected the unit to a performance test on site

2. has instructed the parties responsible for operation of the unit in handling of the unit by
means of the instruction manual.

2-1
2-2
3 RISKS AND SAFETY OF HIGH-FREQUENCY SURGERY

3.1 Unintentional thermal tissue damage

High-frequency surgery is associated in principle with various risks for the patient, the personnel
and surroundings. In order to avoid these risks in practice, the surgeon and his/her assistants
must recognize these risks and observe the appropriate rules for prevention of damage. In the
following, these risks and rules for prevention of damage are explained.

3.1.1 Unintentional thermal tissue damage due to HF leakage currents

During high-frequency surgery, the patient unavoidably conducts high-frequency electrical current
to ground potential. If the patient makes contact with electrically conductive objects during
high-frequency surgery, a high-frequency electrical current can result at the contact point between
the patient and this object, which can in turn cause thermal necroses. Not just objects made of
metal are electrically conductive objects, but also wet cloths.

WARNING

The patient must be insulated against electrically conductive objects during high-frequency
surgery. The black elastic table covers on operating tables demonstrate a certain electrical
conductivity for diverting electrical charges. Therefore they are never suitable for ensuring the
required insulation of the patient against metal parts of the operating table. For this reason, an
electrically insulating intermediate layer, for example dry cover cloths, must be laid between the
patient and this black operating table cover during the application of high-frequency surgery.

Electrically insulated Grounded

surface operating
table
Fig.: Insulated positioning of the patient on the operating table

If it is possible for this intermediate layer to become wet during the operation, for example due
to perspiration, irrigation liquid, urine etc., wetting of these intermediate layers must be prevented
by a watertight sheet of plastic. Urine should be carried away via catheter.

Ÿ Extremities lying against the trunk or skin-to-skin contact points should be insulated from
one another by laying dry cover cloths between them.

Ÿ Do not apply ECG electrodes closer than 15 cm next to the operating field.

Ÿ Needle electrodes or injection cannulae should not be used as ECG electrodes during
high-frequency surgery.

3-1
3.1.2 Unintentional activation of an HF generator
Unintentional activation of an HF generator can lead to burns on the patient if the active electrode
hereby touches the patient directly or indirectly through electrically conductive objects or wet
cloths.

Unintentional activation of an HF generator can, for example, be caused by:

Ÿ Unintentionally pressing a footswitch pedal

Ÿ Unintentionally pressing a fingerswitch

Ÿ Defective fingerswitches, footswitches or cables

Ÿ Penetration of electrically conductive liquids (blood, amniotic fluid, urine, physiological

saline solution, irrigation fluids etc.) into fingerswitches or footswitches.

Ÿ Errors within the high-frequency surgical unit

WARNING

To prevent burns on the patient due to unintentional activation of a high-frequency generator,

the following application rules should be heeded:

Ÿ Never lay active electrodes onto or beside a patient in such a way that they can touch the
patient directly or indirectly through electrically conductive objects or wet cloths.

Ÿ The lines to the active electrodes should be positioned in such a way that they touch
neither the patient nor other lines.

Ÿ Always set the acoustic signal, which indicates the active status of the high-frequency
generator, so that it can be easily heard.

Ÿ For operations in which the cutting or coagulation electrode unavoidably remains in contact
with the patient even in a nonactive condition, e.g. for endoscopic operations, particular
care is required. If such an electrode is unintentionally activated due to an error, this activated
electrode should then not be removed from the body without special supervision. When
removing the activated electrode from the patient’s body, burns can result on all areas
within the body which come into contact with the activated electrode. For this reason, in
case such errors occur, the power switch for the high-frequency surgical unit should be
switched off immediately before an attempt is made to remove the activated electrode
from the body.

3-2
3.1.3 Unintentional thermal tissue damage due to inappropriate application
Generally speaking, the bipolar coagulation technique should be applied in preference to the
monopolar coagulation technique. This particularly applies to coagulations on straight organs,
on which the high-frequency current flows over longer areas through diameters which are
approximately equal or become even smaller.

Fig.: Thermal damage of lateral tissue

The tissue is always first heated at places on the tissue where the diameter is smallest. If the HF current
flows through the same diameter (a) over longer distances, the tissue coagulates over this entire distance.
If the diameter of the tissue next to the application point of the coagulation electrode is smaller than at the
point of application, coagulation will also occur next to the application point (b).

WARNING

Always make certain that the HF current does not flow through thin tissue structures or vessels
with a small diameter.

3.1.4 Unintentional thermal tissue damage due to inappropriate or

nonapplication of the neutral electrode
With inappropriate or even nonapplication of the neutral electrode, there is a large risk of
unintentional thermal tissue damage both at the application point of the neutral electrode as well
as to other areas on the patient’s body.

The neutral electrode must be applied with its entire surface as closely and reliably as possible to
the operating field on the patient’s body.

3-3
 WARNING

The effective contact surface, i.e. the electrical conductive value between the neutral electrode
and the patient must correspond to the HF capacity used, meaning the intensity of the HF current.
Here the effective contact surface means the surface of the neutral electrode which has electrically
conductive contact to the skin of the patient during high-frequency surgery.

a) b)

Fig.: The neutral electrode must be applied at an appropriate location on the patient’s skin using the
entire contact surface available (a). If the neutral electrode has only partial contact to the patient’s skin (b),
there is a risk that burning will occur at this location

3.1.5 Unintentional thermal tissue damage due to unsuitable and/or faulty

accessories
It must be ensured that only accessories in perfect condition are used for high-frequency surgery.
Only accessories that are compatible or tested by the unit manufacturer must be used. This
applies both to the active electrodes including cable and plugs, as well as to the neutral electrodes
including cables and plugs.

When using an instrument with electric insulation, it is necessary to be certain that these insulations
are not overloaded and destroyed by overly high electric voltages. The electric output voltages
for the high-frequency surgical unit are indicated for the various cutting and coagulation modes
relative to the possible settings in this instruction manual. The electric strength of the instrument
insulation can be found in the technical data for the instruments or, in case of doubt, can be
requested from the manufacturer of the respective instrument.

WARNING

All insulation on electrodes, electrode holders, cables, plugs etc. must be in perfect condition.

3-4
3.1.6 Unintentional thermal tissue damage due to inattentiveness
Like a scalpel, high-frequency surgery is always a potential source of danger if handled without
care.

WARNING

The cutting or coagulation electrodes should always be handled with care and laid aside in the
intervals between use so that neither the patient nor other persons can come in contact with the
electrodes.
Laying unused electrode handles or coagulation forceps on the patient, next to the patient or
within folds on the cover cloths is dangerous. Cases of burns on patients are known which were
caused by laying the coagulation forceps within folds on the cover cloths which penetrated
through the cloths into the patient’s skin and resulted in burns without being noticed.

3.1.7 Unintentional thermal tissue damage due to output error

The risk of unintentional thermal tissue damage is proportionate to the intensity and time limit
set on the unit for cutting or coagulation.

WARNING

The intensity for cutting or coagulation should only be set and only activated for as long as
necessary for the intended purpose.
An insufficient effect at a standard setting can, for example, be caused by poor attachment of the
neutral electrode, poor contact in the connectors, defective cables or electrically insulating tissue
remnants on the active electrode. This must be checked before setting at a higher power.

3.1.8 Unintentional thermal tissue damage due to the ignition of flammable

liquids, gases and/or vapors
During high-frequency surgery, electric sparks or arcs that can ignite flammable liquids, gases
or vapors occur at the active electrode.

3-5
 WARNING

Make certain during high-frequency surgical operations that anesthetics, skin cleaning agents
and disinfectants are nonflammable. If their use is unavoidable, they must have completely
evaporated and the vapor must be removed from the area of spark formation before switching on
the high-frequency surgical unit.

Before application of high-frequency surgery in the gastro-intestinal tract, it must be ensured

that no flammable (endogenous) gases are present here. There is danger of explosion if flammable
gases are present. For this reason, these gases must be extracted and/or eliminated by flushing
out the affected lumen with CO2before using high-frequency surgery.
During transurethral resection (TUR), H2O molecules may dissociate into H2 and O2 in the arc
between the resection loop and the irrigation liquid. These gases may collect on the roof of the
urinary bladder as a highly explosive gas mixture. If resection is performed in this gas mixture,
dangerous explosions may occur.

3.1.9 Unintentional burns due to hot electrodes

Cutting and/or coagulation electrodes become hot during cutting and/or coagulation procedures
indirectly through the heated tissue and through the electric arc.

WARNING

Tissue can be unintentionally burnt immediately after cutting and/or coagulation procedures if
electrodes that are still hot touch the tissue. Attention must be especially paid to this during
endoscopic operations, such as during pelviscopic fallopian tube coagulation or during endoscopic
polypectomy.

3.2 Electric shock

An electric shock may occur if the high-frequency surgical unit delivers a too heavy low-frequency
current or if a too heavy low-frequency current flows through the patient into the high-frequency
surgical unit from another voltage source.

3.3 Stimulation of nerves and muscles

A known risk of high-frequency surgery is the unintentional electric stimulation of the patient’s
nerves and muscles. This stimulation can result from low-frequency electrical currents that are
caused either by low-frequency current sources or due to electrical arcs between an active electrode
and the patient’s tissue.

Electric alternating current with a frequency above 300 kHz is unable to stimulate nerves and
muscles.

3-6
During cutting procedures, forced coagulation and spray coagulation, the unavoidable electric
arcs between an active electrode and the tissue nevertheless have the effect that a portion of the
high-frequency alternating current is rectified, from which more or less strongly modulated,
low-frequency current components result which stimulate electrically stimulable structures such
as nerves and muscles.

This can result in more or less strong spasms or muscle contractions.

WARNING

When using high-frequency surgery on electrically stimulable structures, contractions of the

affected muscles must be taken into account. This can occur, for example, during endoscopic
operations in the urinary bladder in the vicinity of the obturator nerve and during operations in
the area of the facial nerve.

3.4 Cardiac pacemaker

For patients with implanted cardiac pacemakers or pacemaker electrodes, irreparable damage to
the pacemaker and disturbance of the pacemaker function, which can lead to ventricular fibrilation,
must be reckoned with.

3.5 Danger of explosion

High-frequency surgical units always generate sparks during operation on the active electrode.
For this reason, it is necessary to make certain during interventions that anesthetics, degreasers
and disinfectants are neither flammable nor explosive. They should at least have evaporated
completely before switching on the high-frequency surgical unit and be removed from the area
of spark formation.

3.6 Interference with other electronic equipment

High-frequency surgical units normally generate high-frequency electrical voltages and currents
which can interfere with other electronic equipment.

When installing or arranging sensitive electronic equipment in the operating room, this problem
should be taken into consideration. In principle, sensitive electronic equipment should be set up
as far as possible from the high-frequency surgical unit and particularly from the cables providing
HF current. In addition, the cables providing HF current, which act like broadcast antennas,
should not be unnecessarily long and should never be positioned parallel or too close to cables
from sensitive electronic equipment.

The unit has been fitted with a special generator in consideration of the disturbance of sensitive
electronic equipment, which generates a relatively low interference level as compared to
conventional high-frequency surgical units.

3-7
3-8
Standard

International 7 8 9 10
4 DESCRIPTION OF THE HIGH-FREQUENCY SURGICAL UNIT

4.1 General description

Cutting with automatic control of the HF voltage (Auto Cut)
The ERBOTOM ICC is equipped with automatic open and closed loop control systems which
control and regulate the parameters relevant to the cutting quality so that each respectively selected
cutting quality is guaranteed to be reproducible and constant.

Adjustable power limitation in the cutting mode

Since the ICC units are equipped with automatic control of the HF voltage in the cutting mode,
a power setting in regard to cutting quality is not required. The adjustable power limitation is
primarily intended to guarantee the safety of the patient from unintentional thermal tissue damage,
and to protect fine cutting instruments, such as fine needle electrodes, from destruction due to
overly high HF currents if these come in contact in activated condition with other metallic
instruments. The latter, for example, is a risk during laparoscopic operations. This adjustable
power limitation must not be confused with the power setting for conventional high-frequency
surgical units, where the cutting quality is directly dependent upon the power setting.

Monopolar and bipolar cutting modes

With the ERBOTOM ICC 350, both monopolar and bipolar cutting electrodes can be operated.
A special operating mode is available for the users of bipolar cutting electrodes, which can be
called up as program “b“.

Cutting with automatic control of the electric arc (HIGH CUT)

HIGH CUT is especially suitable for cutting in tissue with poor electric conduction. Since the
HF voltage in the HIGH CUT mode can attain high values on the active electrode, HIGH CUT
should however only be used with electrically well insulated instruments when cutting in tissue
with poor electric conduction. For bipolar or quasibipolar cutting, HIGH CUT is not recommended
inasmuch as the insulation paths for bipolar and quasibipolar instruments are generally very
small and must not be exposed to higher voltages. For bipolar and quasibipolar instruments,
automatic voltage control is recommended.

PPS (Power Peak System)

The initial incision phase can represent a special problem during an incision, particularly if the
cutting electrode is firmly pressed against the tissue to be cut before activating the HF generator,
so that the cutting electrode has a relatively large-surface, and therefore low-resistance, contact.
This is the case, for example, for TUR and for endoscopic polypectomy. In such cases, the HF
generator must provide higher-than-normal power so that the initial incision can proceed without
delay, for otherwise a very large coagulation necrosis may result at the cutting location. The ICC
is equipped with an automatic power control which recognizes low-resistance loads and controls
the HF generator in such a way that it briefly provides enough power so that the HF voltage, i.e.
the intensity of the electric arc, required for the set cutting quality is ensured even for a low-
resistance load. Thanks to this device, the average power can be limited to relatively small
quantities, which corresponds to an improvement in protection from unintentional thermal tissue
damage.

4-1
ENDO CUT
A further special problem during endoscopic operations, for example during polypectomy and
papillotomy, consists in the fact that the electrodes used for cutting, for example polypectomy
loops and papillotomes, must be guided on long wire pulls through narrow working channels on
flexible endoscopes, and therefore the operator has no direct control over the cutting procedure.
However, particularly for polypectomy and papillotomy, a controlled incision is a requirement
in preventing complications. An incision that is too fast can lead to bleeding of the cut edges due
to lack of sufficient coagulation. An incision that is too slow can cause thermal damage, for
example to the intestinal wall.

Soft coagulation
Soft coagulation can be activated by key or pedal. It is especially advantageous for use in
combination with the Auto Stop mode available in the ICC. Here, the coagulation process is
automatically stopped as soon as the electric resistance of the coagulum increases due to vapor
formation. In this way, the coagulation process is prevented from stopping too early or too late.
If the coagulation process stops too early, coagulation may be insufficient. If coagulation is too
long, the coagulum can dry out and adhere to the coagulation electrode.

Forced coagulation
Forced coagulation is advantageous if an efficient hemostasis is to be achieved with relatively
small-surface electrodes, such as TUR resection loops.

Spray coagulation
The Spray coagulation mode on the ICC is also suitable for Argon Gas coagulation.

Adjustable power limitation in the various coagulation modes

For the ERBOTOM ICC units, the surgically relevant coagulation qualities, i.e. the coagulation
effects Soft Coag., Forced Coag. Spray Coag. and Bipolar Coag., are delimited by definition
from one another and selectable by the press of a key. Nevertheless, the intensity of the different
effects can be varied by power limitation.

The Soft, Forced and Spray modes are each doubly available
In this way, two different coagulation modes can be preset independent of one another and, if
two coagulation instruments are used, applied independent of one another, although not
simultaneously for reasons of safety. Thus for example one coagulation instrument can be
connected and applied to Soft coagulation and another instrument to Argon Plasma coagulation
on the same ICC 350.

Bipolar coagulation
In this coagulation mode, the HF voltage is, similar to Soft coagulation, automatically and
constantly controlled, and its peak value always remains lower than 200 Vp, so that the current
density and thus the coagulation effect is, for the most part, independent of the effective contact
surface between the coagulation electrode and the tissue, provided the effective contact surface
is not too large relative to the currently set power limitation.

The adjustable power limitation serves the purpose of protecting fine bipolar coagulation
instruments, such as pointed bipolar coagulation forceps, from being thermally destroyed in
case of a short between the two forcep tips.

4-2
The footswitch or Auto Start is used for activation.

In the Auto Start mode, the HF generator is automatically activated if both poles of the bipolar
coagulation instruments used contact electrically conductive tissue simultaneously. Auto Start
can occur either immediately at the moment of contact with the tissue or more or less temporally
delayed. With immediate activation, it is possible to work very quickly, especially if several
coagulations must be performed one after another. Delayed activation offers the operator the
advantage that he/she can prepare and securely grasp the tissue to be coagulated with the bipolar
coagulation forceps before the HF generator is automatically activated. Automatic activation of
the HF generator only occurs if both poles of the bipolar coagulation instruments contact the
tissue uninterruptedly for at least as long as the respectively selected delay lasts. If the contact is
interrupted before the respectively selected period of delay is over, the respective period of
delay restarts as of the next contact.

Deactivation can proceed either via the pedal (however only if it was also activated via the
pedal), or via Auto Stop. In the Auto Stop mode, the HF generator is automatically deactivated
as soon as the electric resistance of the coagulum increases due to vapor formation. In this way,
the coagulation process is stopped for the coagulum dries out or even carbonizes. This prevents
the coagulum from adhering to the coagulation electrode and that the coagulation electrode
becomes soiled too quickly.

Programmability of the front panel

In spite of the multiple possibilities for use of the ICC 350, this unit is relatively simple and easy
to operate. This especially applies to the utilization of the memory available in this unit, in
which various front panel settings can be stored.

4-3
4.2 Description of the controls

This symbol, in accordance with EN 60 601-1, is intended to indicate to the user

that this unit must only be used on the patient if the user is acquainted with the
operation and features of this unit.

The figures set in cursive relate to the ICC illustration for this chapter, or to the function
fields in the text.

1 Power switch
Using this power switch, the unit is switched on and off.

Each time after being switched on, the unit automatically proceeds with various performance
checks. If an error in the unit or in the accessories is recognized here, a warning signal
sounds and the determined error is indicated by a corresponding error number. (See Chapter
12.1, Automatic performance checks after switching on the unit). If no error is determined,
the unit is ready to operate.

If the unit was switched off for less than approx. 15 seconds, all settings for the program
used before switching off appear after the automatic performance check on the front panel,
and the unit can be immediately reactivated. This is advantageous if, for example, the
power supply briefly fails.

If the unit was switched off for longer than approx. 15 seconds, the basic setting of the
program used before switching off appears after the automatic performance check on the
front panel, whereby all relevant visual displays continue to blink and the unit cannot be
activated until any key on the front panel is briefly pressed as confirmation that this program
should be used. Then the relevant displays are continously illuminated and the unit can be
activated using the available settings. These settings can be changed or adapted to the
current requirements at any time. However, other programs can be selected as well.

2 - 5 Function fields
The AUTO CUT, AUTO COAG 1, AUTO COAG 2 and AUTO BIPOLAR function fields
can be adjusted separately from one another, although not activated simultaneously for
reasons of safety.

WARNING

Function fields that are not used may be switched off completely to prevent unintentional
activation. To do this the power limitation must be turned down so far in the corresponding
function field until a beep is heard and “—“ appears on the digital display. The corresponding
function field cannot be activated in this condition.

4-4
2 AUTO CUT function field
All parameters can be set in this function field that are relevant to
cutting:

2.1 Setting of the coagulation EFFECT when cutting

Here the required cutting quality in regard to the coagulation effect on the cutting edges
can be adjusted.
Level 1 corresponds to minimum coagulation effect.
Level 4 corresponds to maximum coagulation effect.

2.2 Setting the power limitation

The HF power output can be limited in one watt steps from 300 watts to 1 watt. If display
2.3 shows “—“, the Auto Cut mode is switched off.

2.3 Display of the set power limitation in watts

This display shows the respectively set power limitation

2.4 HIGH CUT ON/OFF

The required Cut mode “AUTO CUT“ or “HIGH CUT“ can be set here. In “AUTO CUT“
mode, the HF voltage is constant. In the “HIGH CUT“ mode, the intensity of the arc
between the active electrode and the tissue is constant.

Activation of monopolar cutting

can be done using either the yellow key on the electrode handle or the yellow pedal on the
footswitch. Activation is visually signaled by continuous illumination of the triangle symbols in
the upper part of the CUT function field and also acoustically signaled. Monopolar cutting
instruments are connected to the CUT/COAG 1 and/or CUT/COAG 2 sockets.

Activation of bipolar cutting

proceeds via the yellow pedal. To do this, program “b“ = bipolar must be selected. Activation is
visually signaled by continuous illumination of the triangle symbol in the upper part of the Auto
Cut function field as well as acoustically signaled. Bipolar instruments are connected to the
BIPOLAR socket. The maximum power setting for bipolar cutting is 100 watts. In program “b“,
the AUTO BIPOLAR function field for bipolar coagulations can also be activated via the blue
pedal of a dual-pedal footswitch or by the white pedal on a single-pedal footswitch. For bipolar
cutting, the High Cut cutting mode is not required and therefore cannot be activated.

4-5
3 AUTO COAG 1 function field
All parameters can be set in this function field and
are relevant to monopolar coagulation:

3.1 Selection of the coagulation mode

By pressing this key, one of the following coagulation modes can be selected:

3.2 Soft coagulation without Auto Stop

3.3 Forced coagulation (Check the version. See Chapter 10.12)

3.4 Spray coagulation (Also suitable for Argon Plasma coagulation)

3.5 Power limitation

The HF power output can be limited in 1 watt steps from 120 watts to 1 watt. If the
display 3.6 shows “—“, the Auto Coag 1 mode is switched off.

3.6 Display of the set power limitation in max. watt

Activation
The coagulation modes for this AUTO COAG 1 function field can be started via the blue key on
an electrode handle, and stopped via this key or automatically (Auto Stop). Activation is visually
signaled by continuous illumination of the triangle symbols in the upper part of the AUTO
COAG 1 function field as well as acoustically signaled.

4-6
4 AUTO COAG 2 function field
All parameters can be set in this function field and
are relevant to monopolar coagulation:

4.1 Selection of the coagulation mode

By pressing this key, one of the following coagulation modes can be selected:

4.2 Soft coagulation without Auto Stop

4.2.1 Soft coagulation with Auto Stop

4.3 Forced coagulation (Check the version. See Chapter 10.12)

4.4 Spray coagulation (Also suitable for Argon Gas coagulation)

4.5 Power limitation

The HF power output can be limited in 1 watt steps from 120 watts to 1 watt. If the
display 4.6 shows “—“, the Auto Coag 2 mode is switched off.

4.6 Display of the set power limitation in max. watt

4.7 Changeover switch for the blue pedal

If the left signal 4.7.1 is illuminated in this key, the currently selected coagulation mode of the
Auto Coag 2 function field can be activated via the blue pedal of a dual-pedal footswitch.

Activation
The coagulation modes for this AUTO COAG 2 function field can be activated via the blue key
on an electrode handle or via the blue pedal of a footswitch and stopped via this key or this pedal
or automatically (Auto Stop). Activation is visually signaled by continuous illumination of the
triangle symbols in the upper part of the COAGULATION function field as well as acoustically
signaled.

4-7
5 AUTO BIPOLAR function field
All parameters can be set in this
function field and are relevant to bi-
polar coagulation:

5.1 Selection of the Auto Start mode

If the unit is to be activated by Auto Start, three different Start modes are available:

AUTO START 2 Auto Start with a long start delay

AUTO START 1 Auto Start with a short start delay
AUTO START 0 Auto Start without a start delay
AUTO START OFF No Auto Start

The operator can use the start delay, for example, to prepare or safely grasp the tissue to
be coagulated with the coagulation forceps before starting.

WARNING

Only use Auto Start if unintentional contact of tissue with the coagulation instrument can be
safely avoided. For endoscopic interventions, such as laparoscopy, pelviscopy or thoracoscopy,
Auto Start should not be used because unintentional contact of the coagulation instrument with
tissue cannot be safely avoided here.

The AUTO START key has no function on the ICC 350 No. 10128-025!

n some countries the ICC units are supplied with the AUTO START function deactivated. This
may also apply in your case. If you nevertheless wish to use the AUTO START function, please
consult your local ERBE branch office. You will find the address on the last page of the Instruction
Manual. Technical Service will activate the AUTO START function for you on request.

5.2 Power limitation

With the Auto Start switched off, the HF power output can be limited in 1 watt steps from
120 watts to 1 watt. With Auto Start, the HF power output is limited to 50 W max. If the
display 5.3 shows “—“, the Auto Bipolar mode is switched off. The power limit is
recommended, for example, for pointed bipolar coagulation forceps, because in this way
thermal damage to the forceps points can be prevented if these directly contact each
other.

5.3 Display of the set power limitation in max. watt

4-8
5.4 Auto Stop mode
In the Auto Stop mode, the HF generator is automatically switched off as soon as the
water reaches the vapor phase in the coagulum. The Auto Stop mode is switched once
signal lamp 5.4.1 is illuminated.

5.5 Activation, changeover switch for the blue pedal of a dual-pedal footswitch
If the right signal 5.5.1 is illuminated in this key, the Auto Bipolar can be started via the
blue pedal on a dual-pedal footswitch. Auto Bipolar can also be activated via the white
pedal on a single-pedal footswitch or by Auto Start.

6 Working with programs

The ERBOTOM ICC 350 is equipped with 11 memory locations for
storage of various basic settings. In this way, the settings required for
every application of high-frequency surgery can be reduced to a
minimum.

A basic setting is the setting which is defined at the factory or by the user and is stored in the
program memory. Consequently, every program has a basic setting.

The basic setting for program “0“ is defined and programmed by the manufacturer and cannot be
reprogrammed by the user. For the ERBOTOM ICC 350, Software Version 1.05 and up, the basic
setting for program “0“ is defined and stored as follows:

AUTO CUT: Auto. voltage control, Effect 3, power limitation 150 watts
Activation with yellow key or yellow pedal
AUTO COAG 1: Soft coagulation, power limitation 60 watts
Activation with blue key
AUTO COAG 2: Forced coagulation, power limitation 60 watts
Activation with blue key or blue pedal
AUTO BIPOLAR: Power limitation 40 watts
Activation with white pedal, Auto Stop off

The basic settings for programs “1“ to “9“, as well as Program “b“ = Bipolar for bipolar cutting
and coagulation, can be custom-defined and programmed by the user. It is recommended that the
corresponding basic settings be documented.

The use of programs is especially practical for special application areas or cutom settings. The
basic setting of each selected program is also immediately available again if the unit has been
switched off in the meantime. If another program is required than that appearing in display 6.3
after the unit is switched on, the required program can be called up by pressing key 6.2
“PROGRAM“. The unit is immediately ready to operate using this program. If necessary, the
functions and parameters appearing on the front panel for the appropriately selected program
through the basic setting, can be changed or adapted to the immediate purpose and, if the changed

4-9
setting is also to be used for the following operations, it can be accepted into this program. To do
this, only the SAVE key 6.1 must be depressed uninterruptedly long enough until “Set“ is indicated
on display 3.6 for Auto Coag 1 and the signal heard continuously during storage changes into an
intermittent signal.

WARNING

The operator and/or user of the unit must ensure that programs are not changed and stored
uncontrollably. Program changes must always be documented and all users must be informed.

Program b = Bipolar
With Program “b“, bipolar instruments connected to the bipolar
output of the unit can be used for coagulation and cutting.

The parameters for bipolar cutting with a choice of coagulation

effect are set via the AUTO CUT function field. The parameters
for bipolar coagulation are set via the AUTO BIPOLAR function
field.

Settings

AUTO CUT The HF power output for bipolar cutting can be limited in 1 watt steps
from 100 watts to 1 watt.
EFFECT can be set from 1 to 4.

AUTO COAG 1 This function field is not limited and all parameters can be set.

AUTO COAG 2 This function field is switched off.

AUTO BIPOLAR The HF power output for bipolar coagulation can be limited in 1 watt
steps from 120 watts to 1 watt.
With the changeover switch for the blue pedal of a dual-pedal
footswitch,
activation can be blocked using the blue footswitch pedal.
Activation of AUTO STOP is possible.
AUTO START is blocked in this program.

4-10
Program E=ENDO CUT
ENDO CUT is a cutting mode in which the incision is automatically
controlled in such a way that alternating short, automatically
controlled cutting intervals result with defined pause intervals. In
this way a polypectomy loop, for example, cannot cut through a
polyp at just any speed, but rather at a controlled speed.

A further special problem during endoscopic operations, for example during polypectomy and
papillotomy, consists in the fact that the electrodes used for cutting, for example polypectomy
loops and papillotomes, must be guided on long wire pulls through narrow working channels on
flexible endoscopes, and therefore the operator has no direct control over the cutting procedure.
However, particularly for polypectomy and papillotomy, a controlled incision is a requirement
in preventing complications. An incision that is too fast can lead to bleeding of the cut edges due
to lack of sufficient coagulation. An incision that is too slow can cause thermal damage, for
example to the intestinal wall.

The initial incision phase can represent a special problem during an incision, particularly if the
cutting electrode is firmly pressed against the tissue to be cut before activating the HF generator,
so that the cutting electrode has a relatively large-surface, and therefore low-resistance, contact.
This is the case, for example, for endoscopic polypectomy of larger polyps as well as for
papillotomy. In such cases, the HF generator must provide higher-than-normal power so that the
initial incision can proceed without delay, for otherwise a very large coagulation necrosis may
result at the cutting location. The ERBOTOM ICC 350 is also equipped in the ENDO CUT
mode with an automatic initial incision control which recognizes low-resistance loads and controls
the HF generator in such a way that it briefly provides enough power so that the initial incision
can proceed without delay. As soon as the initial incision has been made, the HF voltage for the
intensity of the electric arc required for the respectively selected cutting quality is automatically
controlled and the cutting procedure is automatically fractionated as described above. Thanks to
this device, the entire cutting procedure from the start to the finish of the incision is automatically
controlled. Additionally, this considerably reduces the average power during an incision as
compared to unregulated, nonautomatically controlled high-frequency surgery units.

Settings

AUTO CUT The HF power output for ENDO CUT can be limited in 1 watt steps from
200 watts to 1 watt. The LED for HIGH CUT is illuminated.
EFFECT can be set from 1 to 4.
AUTO COAG 1 This function field is not limited and all parameters can be set.
AUTO COAG 2 This function field is not limited and all parameters can be set.
AUTO BIPOLAR This function field is not limited and all parameters can be set.

4-11
7 Connecting socket for neutral electrodes
For monopolar cutting and/or coagulation, a suitable neutral electrode must be used that must
both be connected to the unit as well as carefully applied to the patient.

The ERBOTOM ICC 350 is equipped with a Neutral Electrode Safety System (NESSY) which
automatically monitors the electrical connection between the neutral electrode and the unit as
well as application of the neutral electrode on the patient. The latter only then however if neutral
electrodes with two contact surfaces are used (See Chapter 4.3.5 NESSY).

WARNING

If single-surface neutral electrodes are used, the NESSY only monitors the electrical connection
between the neutral electrode and the unit, but not the application of the neutral electrode on the
patient.

The pictograms beside the connecting socket for neutral electrodes have the following explanation:

Neutral electrode in general

The ERBOTOM ICC 350 conforms to the requirements of Type CF in accordance

with EN 60 601-1. In addition, this pictogram indicates in accordance with EN 60
601-2-2 that the neutral electrode can remain applied to the patient during
defribillation.

The capacitive grounding of the neutral electrode and the type CF appear to contradict one
another. The ICC 350 fulfills both specifications at the same time because it is equipped with a
low-frequency leakage current monitor, which automatically monitors low-frequency leakage
currents that flow into or out of the unit.

8 Connecting socket for the AUTO CUT and AUTO COAG 1 function fields
Electrode handles with fingerswitches can be operated from this connecting socket. This
connecting socket can only be activated via the fingerswitch.

Information regarding the connection and the activation possibilities of instruments for Argon
Plasma surgery (APC) can be found in the instruction manuals for APC units.

9 Connecting socket for the AUTO CUT and AUTO COAG 2 function fields
Electrode handles or other monopolar coagulation instruments with or without fingerswitches
can be operated from this connecting socket. Also other monopolar instruments with or without
switches, such as rigid or flexible endoscopes for endoscopic operations, can be connected to
this connecting socket. Make certain here that the plug type is suitable. This connecting socket
can either be activated via the fingerswitch or pedals of a footswitch.

Information regarding the connection and the activation possibilities of instruments for Argon
Plasma surgery (APC) can be found in the instruction manuals for APC units.

4-12
 WARNING

For simultaneous connection of two electrode handles to both monopolar connecting sockets 8
and 9, electrode handles (particularly if they look alike) must be laid down in such a way that
there can be no mix-up. In case of doubt, a trial activation of the unit should be performed
without contacting the patient with the active electrode.

10 Connecting socket for the AUTO BIPOLAR function field

Bipolar instruments for coagulation or cutting can be connected to this connecting socket.

The coagulation mode can be activated via pedal or Auto Start. In the coagulation mode, the
Auto Stop function is also available.

The bipolar cutting mode is available in Program “b“ and can be activated via the yellow pedal.
CAUTION

When using pointed bipolar coagulation forceps, the tips can be thermally damaged due to electric
currents that are too high. To prevent this, it is recommended that the power limitation be set as
low as possible and/or make certain that the tips of the bipolar coagulation forceps do not touch
one another..

11 Safety field
High-frequency surgical units of the ERBOTOM ICC series are equipped with various safety
devices to protect the patients and users.

12 Connecting socket for a dual-pedal footswitch

A dual-pedal footswitch can be connected to this connecting socket. When using a dual-pedal
footswitch, only the AUTO function field can be activated with the yellow pedal. Using the blue
pedal, either the AUTO COAG 2 or AUTO BIPOLAR function field can be activated. The blue
pedal is assigned to the AUTO COAG 2 or AUTO BIPOLAR function field via the key PEDAL
between the AUTO COAG 2 and AUTO BIPOLAR function fields.

13 Connecting socket for a single-pedal footswitch

A single-pedal footswitch can be connected to this connecting socket, by which the AUTO
BIPOLAR function field can be activated. When using the ICC 350 in combination with an
Argon Plasma coagulation unit model APC 300, the APC 300 is joined to this connecting socket
on the ICC 350 via a special cable (detailed information on this can be found in the APC 300
instruction manual).

WARNING

If both a dual-pedal footswitch and a single-pedal footswitch are connected to the unit, the
AUTO CUT, AUTO COAG 2 and AUTO BIPOLAR function fields can, for example, be activated
via the corresponding pedals without further changeovers on the unit.

4-13
14 Terminal for potential equalization
For this, see Chapter 10.4, INSTALLATION.

15 Volume of the acoustic signal

The volume of the acoustic signals can be adjusted with this knob.
This does not apply to warning signals, which must always be sufficiently loud.

WARNING

An important purpose of this acoustic signal is to protect the patients and personnel from burns
due to unintentional activation of the high-frequency generator (for more information, see Chapter
3.1.2, Unintentional activation of a high-frequency generator).

16 Loudspeaker for acoustic signals

Always set up the instrument in such a way that acoustic signals are easily heard from this
speaker. The volume of the acoustic signals is set at the factory.

17 Power connection
This high-frequency surgical unit must only be connected via the power cord supplied by the
unit manufacturer or one of these of equal quality, which bears the national test symbol, to
correctly installed hospital grade power sockets. Here, for reasons of safety, no multiple sockets
or extension cords must be used if possible. If their use is unavoidable, they must be equipped
with a correctly functioning grounded connector.

18 Power fuses
The unit is secured with two fuses. If these fuses fail, an authorized technician should inspect the
unit for possible errors before putting back into operation.

4-14
4.3. Description of the safety features
The ICC 350 is equipped with the following safety features:

4.3.1 LF LEAKAGE = Automatic monitoring of low-frequency leakage currents

4.3.2 HF LEAKAGE = Automatic monitoring of high-frequency leakage currents

4.3.3 OUTPUT ERROR = Automatic monitoring of unit-related output error

4.3.4 TIME LIMIT = Automatic monitoring of the time limit
4.3.5 NESSY = Neutral Electrode Safety System

4.3.6 Protection against operating error

4.3.1 Low-frequency leakage current monitor

The ERBOTOM ICC 350 can optionally be operated in Floating
Output or in Earth Referenced Output mode. These modes
can be changed over by a technician authorized to do this (see
Chapter 10.13). In the Floating Output mode, the low-frequency
leakage curent generally represents no problem, because the
applied part here is extensively insulated to ground potential. In
the Earth Referenced Output mode, the neutral electrode within
the unit is capacitively related to ground potential. A low-frequency
leakage current higher than 0.05 mA can flow through this capacity
if need be. For this reason, the ERBOTOM ICC 350 is equipped
with an LF leakage monitor which automatically monitors the LF
leakage current flowing through the patient via the applied part of the high-frequency surgical
unit. If the LF leakage current rises above 0.05 mA, the LF leakage monitor automatically separates
the capacitive ground for the neutral electrode within the unit immediately, which decreases the
LF leakage current to less than 0.05 mA. This error is indicated visually as Error no. 5 and
acoustically. The HF generator can only be activated once the cause of error has been eliminated.

In this way, the ERBOTOM ICC 350 also fulfills the Type CF requirements in the Earth
Referenced mode.

4.3.2 High-frequency leakage monitor

HF leakage currents are unavoidable during high-frequency surgery.
This especially applies to all monopolar application techniques.

To prevent HF leakage currents flowing uncontrolled through the

patient and causing unintentional burns, patients should have no
contact with electrically conductive objects during high-frequency
surgery. This especially applies to objects that are conductive or
capacitively grounded. If this requirement is fulfilled, burns on
patients due to HF leakage are avoidable.

In EN 60 601-2-2, Sec. 19.101, the maximum permissible HF

leakage current which cannot cause noticeable burns on patients
is given as 150 mA.

4-15
In practice, despite careful positioning of the patient on the operating table, unintentional contact
of the patient with electrically conductive objets can occur. In some operations, such contacts
are unavoidable.

The ICC is therefore equipped with an HF leakage monitor, which automatically monitors the
HF leakage current and generates a visible warning signal if the HF leakage exceeds 150 mA eff.

If the HF leakage current exceeds 300 mAeff, the HF leakage monitor additionally produces an
acoustic signal. If the acoustic signal is heard, the operator should then only continue to use
high-frequency surgery if, for example, an incision or a hemostasis has absolute priority.

4.3.3 Unit-related output error

The ICC is equipped with automatic monitoring of the HF output
parameters, which monitors deviations in the actual value from the
set value for the currently set HF output parameters and produces a
warning signal and/or switches off the HF generator if the deviation
is so large than the required quality of the respective effect (cutting
or coagulation) is no longer ensured. In case of deviations or absence
of the required effect, display of a unit-related output error allows
the operator to immediately check whether the defect is caused by
the unit or not.

Deviations in the HF output parameters from the currently set HF output parameters on the ICC
can only result from loads which have too low a resistance, e.g. coagulation electrodes that are
too large, a short circuit between the active and neutral electrode, or due to an error in the unit.

4.3.4 Time limit

With normal use, a high-frequency generator is only activated briefly
for performance of an incision or a coagulation by fingerswitch,
pedal or AUTO START. This generally lasts only a few seconds.

Through an error in the unit, in the accessories or in use, the high-

frequency generator can be switched on unintentionally. To prevent
greater damage due to unintentional activation of the high-frequency
generator, the ICC is equipped with a monitor which automatically
monitors the time limit on the high-frequency generator. Once a
predetermined maximum time limit has been exceeded, this monitor
generates a visible signal. If the high-frequency generator is then
not switched off, the generator additionally produces an acoustic signal and automatically switches
the HF generator off. The high-frequency generator can however be restarted at any time, whereby
the time limit is also monitored anew. In this way, greater damage due to unintentional activation
of a high-frequency generator for undeterminably long times is avoided.

4-16
Custom adaptation of the maximum time limit
In consideration of the risk of thermal tissue damage due to unintentional switching on of an HF
generator, an unintentionally switched-on HF generator should be switched off again as soon as
possible automatically. Since the unit cannot automatically distinguish between intentional and
unintentional switching on of an HF generator, the automatic switching off of an HF generator
must not occur too quickly, because this would hinder the operator during cutting and/or
coagulation. Since the risk of thermal tissue damage varies greatly among the various operating
modes, the ICC can adapt and store the maximum time limit for each operating mode and in
each storable program via the Test program no. 10 of at least 3 sec. to a maximum of 900 sec.

WARNING

For reasons of safety, a change in the automatic limitation of the maximum time limit must only
be made if all users of this unit are informed properly and in good time about this change.
In addition, a change in the automatic limitation of the maximum time limit must be properly
documented, for example in the medical product logbook of the respective unit.

4-17
4.3.5 NESSY
The units in the ERBOTOM ICC model series are equipped with
a Neutral Electrode Safety System (NESSY), which monitors both
the electric connection between the unit and neutral electrode as
well as the correct application of the neutral electrode on the
patient.

When using neutral electrodes with only one contact surface, only
the electric connection between the unit and neutral electrode is
automatically monitored. If this connection is sound, the green
NESSY signal (LED) is illuminated and all operating modes can
be activated. If this connection is interrupted, the green NESSY
signal (LED) is not illuminated and the monopolar operating modes
cannot be activated. If an attempt is made in this condition to activate
a monopolar operating mode, the red NESSY signal (LED) is
illuminated and a warning signal is heard at the same time.

When using neutral electrodes with two contact surfaces, not only
the electric connection between the unit and neutral electrode is
automatically monitored, but also the application of the neutral
electrode on the patient. Here the electric conductance between
the two contact surfaces on the neutral electrode and the skin of
the patient is constantly measured automatically and compared
with the intensity of the high-frequency current that flows through
the neutral electrode.

If the intensity of the high-frequency current is greater than is permissible at the respectively
measured conductance, NESSY then produces visual and acoustic warning signals and the operator
should only continue to use the high-frequency surgery if an incision or hemostasis has absolute
priority. If the measured conductance between the neutral electrode and the patient is too small,
monopolar operating modes cannot be activated.

The diversity of neutral electrodes models for high-frequency surgery is very large. The ideal
neutral electrode, optimal for all applications, does not yet exist. To ensure the user a large
degree of freedom in the selection of the best suited neutral electrodes for his/her purposes,
NESSY is a flexible Neutral Electrode Safety System that can be adapted optimally to the neutral
electrodes selected by the user. For appropriate advice and adaptation to suit requirements, please
contact your local Erbe office (see Chapter Addresses).

4-18
 WARNING

For reasons of safety, a change to NESSY may only be made if it has been properly ensured that
all users of this unit are informed in good time about this change. In addition, a change to
NESSY must be properly documented.

When using dual-surface neutral electrodes, NESSY also monitors the application direction of
the contact surface relative to the direction of current flow. Since the high-freqeuency current is
generally not distributed evenly over the contact surface of the neutral electrode, but rather can
be greater at the proximal corners or edges to which the current flows than at the distal corners or
edges, attention should always be paid during application of neutral electrodes that the current
flows toward the long edge.

NESSY compares the intensity of the two partial currents I1 and I2 of the high-frequency current
IHF, which flow through the two partial surfaces of the neutral electrode. If the partial currents I1
and I2 deviate from one another, the red NESSY signal is illuminated. If the partial currents
deviate extremely from one another, the red NESSY signal is illuminated and at the same time
the NESSY warning signal is heard, and the HF generator is automatically switched off.

Neutral electrode suitable for NESSY - applied correctly

Neutral electrode suitable for NESSY - applied incorrectly

4-19
 Correct application

The correct application must be observed not only for divided, but also for undivided neutral
electrodes.

WARNING

Before the neutral electrode is applied to the patient’s body, a check must be made as to whether
the green NESSY signal (LED) does not light when using a neutral electrode with two contact
surfaces.

4.3.6 Protection against operating error

To prevent operating errors, the front panel is designed in such a way that illogical and/or
incomplete settings are automatically monitored and signaled.

The female connector beneath the front panel contains all the connecting sockets for the applied
part.

These connecting sockets are designed in such a way that only plugs from intended accessories
can be inserted (provided that only accessories recommended or supplied by the manufacturer
of the unit are used).

4-20
You may connect three instruments at the same time to the ICC. For reasons of safety, these can
however only be used alternately. Only one socket ever carries HF voltage.

Each time after switching on the power switch, an automatic test program is started within the
unit which recognizes and signals the following errors in the operating controls for the unit and
for accessories connected to the unit:

1. If a key on the front panel is shorted or pressed due to an error when the power switch is
switched on, this error is indicated acoustically and by an Error Number after the power
switch has been switched on.

2. If a key on the electrode handle is shorted or bypassed at low resistance due to an error
(e.g. by moisture in the electrode handle) or pressed while the power switch is switched
on, this error is signaled acoustically and indicated by an Error Number after switching on
the power switch.

3. If a footswitch contact is shorted due to an error, a pedal sticks or a pedal is pressed while
the power switch is switched on, this error is indicated acoustically and by an Error Number.

CAUTION
Every function field can only then be activated if it has been completely set. If an attempt is
made to activate a function field which has not or not completely been set, the unit produces an
intermittent acoustic warning signal and indicates this operating error by illumination of the
triangle symbols on the corresponding function field.

4-21
4-22
5 ERBOTOM ICC 350 Z

5.1 Intended use

The ERBOTOM ICC 350 Z is equipped with a Neurotest device which is used to localize
electrically excitable tissue structures.

5.2 Additional controls

19 Connecting socket for the active Neurotest electrode on the front panel
To prevent a mix-up of the electrode handles for high-frequency surgery and the electrode handle
for the Neurotest device, electrode handles no. 20190-027, 20190-061 for the Neurotest device are
equipped with a different plug than the electrode handles for high-frequency surgery. It is
connected to socket 19. The silver needle for nerve test no. 20191-079 is inserted into the electrode
handle.

20 Connecting socket for remote control of the Neurotest setting on the rear
panel
The Neurotest device is switched on, and the current pulse amplitudes are adjusted using a
remote control no. 20121-007 which is connected to this socket.

5-1
5.3 Operation
Basics
The NEUROTEST device in the ERBOTOM ICC 350 Z is used for intraoperative differentiation
of electrically stimulable tissue structures, for example the facial nerve, during surgical operations
in dental, oral and maxillofacial medicine (DOM). Here, an electric stimulation in the form of
periodical current pulses is applied to the tissue to be differentiated and any reaction of the
stimulated muscle is observed.

The possibility of localization of motor nerves and/or muscles using electric current pulses in
electrically conductive tissue structures G is based upon the physical circumstance that electric
current flows divergently into the tissue from the stimulation electrode E, i.e. the current density
i in the tissue decreases as the distance increases from the stimulation electrode, i.e. inversely as
the square of the distance r.

Consequently, due to this physical condition, a localization of motor nerves and/or muscles is all
the more precise the smaller the intensity of the current I is. The implication of this for the
practical localization of electrically excitable tissue structures is that a relatively high current
intensity permits a fast but imprecise localization, and a relatively low current intensity allows a
more time-consuming but therefore more precise localization.

The application of current pulses during DOM

The current pulses can be applied monopolarly via a coagulation electrode. The current returns
to the unit via a neutral electrode applied to the patient.

Form of the current pulses

The NEUROTEST device supplies square-wave current pulses with 0.33 ms pulse duration and
550 ms pause duration. The amplitude of the current pulses can be set to a maximum of 25 mA.

Activation of current pulses during DOM

The Neurotest device is switched on and set via a remote control connected to the rear panel of
the unit.

5-2
If the knob for this remote control is set to switch position 0, the Neurotest device is switched
off. This is indicated by the signal lamp labelled HF. For switch positions 1-5, the Neurotest
device is switched on and can be activated via the Neurotest electrode handle. This is indicated
by the signal lamp labelled NT.

The stimulation current pulses from the NEUROTEST device are transmitted via the electrode
handle with electrode connected to the NEUROTEST socket. It is activated via the key on the
Neurotest electrode handle.

The Neurotest device can only be activated in switch positions 1-5 on the remote control.

Setting the intensity of the current pulses

The intensity of the current pulses can be set from 5 to 25 mA in five steps of 5 mA each. The
respectively set intensity is automatically and constantly controlled within the practically expected
resistance range.

Step 1 = 05 mA from 0 to 20.0 kOhm

Step 2 = 10 mA from 0 to 10.0 kOhm
Step 3 = 15 mA from 0 to 6.6 kOhm
Step 4 = 20 mA from 0 to 5.0 kOhm
Step 5 = 25 mA from 0 to 4.0 kOhm

Signaling of the current pulses

It is a prerequisite for clear identification of electrically stimulable tissue structures that current
pulses are actually present. If the unit did not provide any current pulses, for example due to an
interruption in the cables unnoticed by the user, and consequently no stimulation occurs, this
could erroneously lead to the belief that no electrically stimulable tissue structures are present in
the affected area.

For this reason, the NEUROTEST device only produces acoustic signals (beeps) if the current
pulses are flowing with at least 3 mA. Current pulses can only flow if the stimulation electrode
is in contact with electrically conductive tissue and the circuit is closed by the patient via the
neutral electrode.

Safety of the NEUROTEST device

The following safety-related functions of the NEUROTEST device in the ERBOTOM ICC 350 Z
are automatically monitored:

a) When activating the NEUROTEST device, a test is first made as to whether a neutral electrode
is connected to the unit and to the patient (the latter only if a neutral electrode with two
contact surfaces is used). If there is an error, this is signaled visually and acoustically.

b) During every activation of the NEUROTEST device, the pulse generator is monitored for
unit-related output error. Here, every pulse is automatically monitored. If the amplitude of
a pulse is greater or less than the currently set amplitude, the unit produces warning signals.
If the amplitude of a pulse exceeds a maximum value, the output circuit is automatically
switched off immediately. If the amplitude was so high that the electronic fuse was triggered,
this error is indicated by error no. 90.

c) Every time after switching on the NEUROTEST device, the function of the electronic fuse
hardware is automatically tested. If an error in the electronic fuse hardware is determined,
this is indicated for a few seconds by error no. 91.

5-3
d) The maximum activation time for the NEUROTEST device is automatically limited for
reasons of safety. After 80 seconds of uninterrupted activity, the “time limit” visual signal
is illuminated and after a further 10 seconds, the Neurotest device is automatically
deactivated. However, the Neurotest device can be immediately reactivated after this.

5.4 Technical data

NEUROTEST device in the ERBOTOM ICC 350 T
Pulse waveform square
Pulse duration 0.33 ms
Pause length 550 ms
Pulse amplitude Step 1 = 05 mA
Step 2 = 10 mA
Step 3 = 15 mA
Step 4 = 20 mA
Step 5 = 25 mA
Constancy of the amplitude automatically controlled
Acoustic signals synchronous with the current pulses from at least
3 mA
Prevention of unit-related output error yes

5-4
6 ERBOTOM ICC 350 T

6.1 Intended use

The ERBOTOM ICC 350 T is equipped with a Neurotest device which is used to localize
electrically excitable tissue structures.

6.2 Additional controls

9 Connecting socket for the active Neurotest electrode on the front panel
Electrode handles for cutting and coagulation are also connected to this socket.

19 Connecting socket for remote adjustment of the Neurotest setting on the

rear panel
The Neurotest device is switched on, and the current pulse amplitudes are adjusted using a
remote control no. 20191-007 which is connected to this socket.

6-1
6.3 Operation
Basics
The NEUROTEST device in the ERBOTOM ICC 350 Z is used for intraoperative differentiation
of electrically stimulable tissue structures, for example the external sphincter during transurethral
resections (TUR) of the prostate. Here, an electric stimulation in the form of periodical current
pulses is applied to the tissue to be differentiated and any reaction of the stimulated muscle is
observed.

The possibility of localization of motor nerves and/or muscles using electric current pulses in
electrically conductive tissue structures G is based upon the physical circumstance that electric
current flows divergently into the tissue from the stimulation electrode E, i.e. the current dtensity
i in the tissue decreases as the distance increases from the stimulation electrode, i.e. inversely as
the square of the distance r.

Consequently, due to this physical condition, a localization of motor nerves and/or muscles is all
the more precise the smaller the intensity of the current I is. The implication of this for the
practical localization of electrically excitable tissue structures is that a relatively high current
intensity permits a fast but imprecise localization, and a relatively low current intensity allows a
more time-consuming but therefore more precise localization.

The application of current pulses during TUR

The current pulses can be applied monopolarly via a coagulation electrode. The current returns
to the unit via a neutral electrode applied to the patient for the TUR.

Form of the current pulses

The NEUROTEST device supplies square-wave current pulses with 50 ms pulse duration and
550 ms pause duration. The amplitude of the current pulses can be set to a maximum of 25 mA.

50 ms

6-2
Activation of current pulses during TUR
The Neurotest device is switched on and set via a remote control connected to the rear panel of
the unit. Via this remote control, the operating mode of the unit can be switched over from high-
frequency surgery (HF) to Neurotest (NT).

If the knob on the remote control is set at switch position 0, the unit is in the high-frequency
surgery operating mode. This is indicated by the signal lamp labelled HF. For switch positions 1-
5, the unit is in the Neurotest operating mode. This is indicated by the signal lamp labelled NT.
In addition, there is a display on the front panel of the ICC 350 T.

The stimulation current pulses of the Neurotest device are transmitted via the electrode handle
with electrode connected to the CUT/COAG2/NEUROTEST socket. This is activated via the
yellow pedal on the footswitch. The Neurotest device can only be activated in switch positions
1-5 on the remote control.

The high-frequency surgery operating mode is only active in switch position 0 on the remote
control or when the remote control is not connected.

Setting the intensity of the current pulses

The intensity of the current pulses can be set from 5 to 25 mA in five steps of 5 mA each. The
respectively set intensity is automatically and constantly controlled within the practically expected
resistance range.

Step 1 = 05 mA from 0 to 20.0 kOhm

Step 2 = 10 mA from 0 to 10.0 kOhm
Step 3 = 15 mA from 0 to 6.6 kOhm
Step 4 = 20 mA from 0 to 5.0 kOhm
Step 5 = 25 mA from 0 to 4.0 kOhm

Signaling of the current pulses

It is a prerequisite for clear identification of electrically stimulable tissue structures that current
pulses are actually present. If the unit did not provide any current pulses, for example due to an
interruption in the cables unnoticed by the user, and consequently no stimulation occurs, this
could erroneously lead to the belief that no electrically stimulable tissue structures are present in
the affected area.

For this reason, the NEUROTEST device only produces acoustic signals (beeps) if the current
pulses are flowing with at least 3 mA. Current pulses can only flow if the stimulation electrode
is in contact with electrically conductive tissue and the circuit is closed by the patient via the
neutral electrode.

Safety of the NEUROTEST device

The following safety-related functions of the NEUROTEST device in the ERBOTOM ICC 350 T
are automatically monitored:

a) When activating the NEUROTEST device, a test is first made as to whether a neutral
electrode is connected to the unit and to the patient (the latter only if a neutral electrode
with two contact surfaces is used). If there is an error, this is signaled visually and
acoustically.

6-3
b) During every activation of the NEUROTEST device, the pulse generator is monitored for
unit-related output error. Here, every pulse is automatically monitored. If the amplitude of
a pulse is greater or less than the currently set amplitude, the unit produces warning signals.
If the amplitude of a pulse exceeds a maximum value, the output circuit is automatically
switched off immediately. If the amplitude was so high that the electronic fuse was triggered,
this error is indicated by error no. 90.

c) Every time after switching on the NEUROTEST device, the function of the electronic fuse
hardware is automatically tested. If an error in the electronic fuse hardware is determined,
this is indicated for a few seconds by error no. 91.

d) The maximum activation time for the NEUROTEST device is automatically limited for
reasons of safety. After 80 seconds of uninterrupted activity, the “time limit” visual signal
is illuminated and after a further 10 seconds, the Neurotest device is automatically
deactivated. However, the Neurotest device can be immediately reactivated after this.

6.4 Technical data

NEUROTEST device in the ERBOTOM ICC 350 T
Pulse waveform square
Pulse duration 50 ms
Pause length 550 ms
Pulse amplitude Step 1 = 05 mA
Step 2 = 10 mA
Step 3 = 15 mA
Step 4 = 20 mA
Step 5 = 25 mA
Constancy of the amplitude automatically controlled
Acoustic signals synchronous with the current pulses from at least
3 mA
Prevention of unit-related output error yes

6-4
7 ERBOTOM ICC 350 M

7.1 Intended use

As a complement to the ICC 350, the ERBOTOM ICC 350 M is intended for the operation of
multifunctional instruments with pneumatic actuator and MIN instruments. For this, it is equipped
with the programs C = MIC (minimally invasive surgery) and n = MIN (minimally invasive
neurosurgery) and additional controls.

7.2 Additional controls

19 Connecting socket for multifunctional MIC instruments and MIN
instruments

20 Compressed air input from an external compressed air source

As an external compressed air source, a compressed air bottle or the central compressed air
supply in the OR can be used, for example. The pressure should be at least 4 bar and at most 6
bar.

CAUTION

Use only dry compressed air.

To connect the unit to the central compressed air supply or to a compressed air bottle, use the
ERBE compressed air tube No. 20 128-000 (5 m long) or No. 20 128-001 (1 m long).

7-1
7.3 Operation
Program C = MIC (Minimally Invasive Surgery)
The “C“ program is intended for the operation of multifunctional
instruments with pneumatic actuator on the MIC connecting socket.
In this program, the parameters for multifunctional instruments
can be set. Functions which are irrelevant or even impermissible
for the operation of such instruments are limited or switched off
according to the instrument.

Settings
(e.g. for instrument 1)

The limitations for other instruments are described in the instrument instruction manual.

AUTO CUT The HF output power for cutting with the instrument can be limited in 1
watt steps from 40 watts to 1 watt.
EFFECT can be set from 1 to 3.
AUTO CUT is blocked for electrode handles with 2 keys that are
connected to the CUT/COAG 1 socket.

AUTO COAG 1 This function field is not limited and all parameters can be set.

AUTO COAG 2 The HF power output for SOFT can be limited in 1 watt steps from
120 watts to 1 watt. For FORCED from 60 watts to 1 watt. SPRAY is
blocked.
Activation of AUTO STOP during SOFT is possible.
Electrode handles with 2 keys that are connected to the CUT/COAG 2
socket cannot activate the unit.

AUTO BIPOLAR This function field is blocked. In the display, the position of the needle
of the multifunctional instrument appears.
“-nd” means needle extended,
“nd” needle withdrawn.

Operation of multifunctional instruments with pneumatic actuator on an

Erbotom ICC 350 M
1. Installation
1.1 Connect the ERBOTOM ICC 350 M to a compressed air source with 5 +/- 1 bar. As a
compressed air source, the central compressed air supply of the OR can be used. To connect
the ERBOTOM ICC 350 M to the standard gas supply outlet according to DIN 13 260 Part
2 in the operating room, use one of the following ERBE compressed air tubes:

ERBE compressed air tube, 5 m long, Article No. 20128 - 000

ERBE compressed air tube, 1 m long, Article No. 20128 - 001

7-2
1.2 If the multifunctional instrument is equipped with aspiration and/or irrigation channels,
these must be connected to the appropriate aspiration and/or irrigation devices.

WARNING

If the aspiration and/or irrigation channels of a multifunctional instrument are not used during
application in insufflated bodily cavities, the terminals for these channels must be closed with
Luer-lock caps.

2. Connect the multifunctional instrument to the ERBOTOM ICC 350 M.

The ERBOTOM ICC 350 M is equipped with an Instrument Identification System (IIS).
As soon as a multifunctional instrument is connected to the MIC socket (19), the IIS
automatically checks which instrument it is and briefly displays the code number of the
respective instrument. Then the IIS calls up the program defined and stored for this
instrument, whereby the ERBOTOM ICC 350 M is automatically configured especially
for this instrument. If an instrument without coding is connected to the MIC socket, the
ERBOTOM ICC 350 M remains in the basic configuration of the “C” program.

The front panel settings for both the basic configuration of the “C” program and also the
instrument-specific configurations can be changed manually, although the setting
possibilities are limited specific to the instrument in consideration of the safety of the
patients and the electrical load capacity of the instruments.

7-3
Program n = MIN (Minimally Invasive Neurosurgery)
The “n” program is intended for operating MIN probes on the MIC
connecting socket. In this program, the parameters for these probes
can be set. Functions that are irrelevant or even impermissible for
the operation of such instruments are limited or switched off
according to the instrument.

Settings
(e.g. for instrument 1)
The limitations for other instruments are described in the respective Notes on use.)

AUTO CUT The HF power output for cutting with the instrument can be limited in 1
watt steps from 15 watts to 1 watt.
EFFECT can be set from 1 to 4.
AUTO CUT is blocked for electrode handles with 2 keys that are
connected to the CUT/COAG 1 socket.

AUTO COAG 1 This function field is not limited and all parameters can be set.

AUTO COAG 2 The HF power output for SOFT can be limited in 1 watt steps from 15
watts to 1 watt. FORCED and SPRAY are blocked.
Activation of AUTO STOP during SOFT is possible.
Electrode handles with 2 keys that are connected to the CUT/COAG 2
socket cannot activate the unit.

AUTO BIPOLAR This function field is not limited and all parameters can be set.

7.4 Technical data

Programmability
Program n = MIN Custom programmable by the user
Program "C" = MIC Custom programmable by the user
Programming Via key on the front panel
Program storage Via key on the front panel
Calling up program Via key on the front panel

Compressed air terminal

Required pressure 5 ± 1 bar

7-4
8 ERBOTOM ICC 350 M-DOKU

8.1 Intended use

As a supplement to the ICC 350, the ERBOTOM ICC 350 M-DOKU is intended for the operation
of multifunctional instruments with pneumatic actuator and MIN instruments. For this, it is
equipped with the programs C = MIC (minimally invasive surgery) and n = MIN (minimally
invasive neurosurgery) and additional controls.

Furthermore, this high-frequency surgical unit can be connected to a PC. With the PC and the
DOKU program, the parameters of the unit can be recorded via accessories during activation.

Regarding the functions of the MIC / MIN, please read Chapter 7.

8.2 DOKU system

With a PC and the DOKU program, the parameters of the unit (voltage, current, resistance,
power, cosine Phi, spark intensity and energy over time) can be recorded during activation via
the accessories (optical waveguide cable, optical waveguide box). There is no electrical connection
between the computer and the ICC 350 M-DOKU, since communication is via optical waveguide.

Installation
1. Connect the optical waveguide box to the COM1 interface of the computer using the 9-pin
Sub-D cable.

2. Switch on the computer and the ICC 350.

3. Connect the optical waveguide cable to the optical waveguide box. On the other end of the
optical waveguide cable, one of the two connecting plugs lights up in red.

4. Connect the illuminated connecting plug with the non-illuminated optical waveguide socket
of the ICC 350.

5. Connect the other connecting plug from the optical waveguide cable to the illuminated
connecting socket of the ICC 350.

Set-up instructions
The PC or the laptop with the optical waveguide box must be set up outside the prescribed
patient surroundings. This means further than 1.5 m from the patient table. The distance to other
units in the OR and the ICC 350 M-DOKU must also be greater than 1.5 m. The computer, the
optical waveguide box and the keyboard must not be able to be touched from the patient
surroundings.

WARNING

The computer must never be placed on or under the ICC 350. The minimum distance of 1.5 m to
the patient, the units, the OR and the ICC 350 absolutely must be maintained.

8-1
The length of the optical waveguide cable is sufficient to connect the optical waveguide box to
the ICC 350 M-DOKU. The computer and the plug-in power supply unit for the optical waveguide
box are supplied with system voltage via a permanently installed power outlet. The ICC 350 is
supplied with system voltage via another permanently installed power outlet.

WARNING

The computer, the plug-in power supply unit for the optical waveguide box and the ICC 350 M-
DOKU must never be supplied together with system voltage via a multiple power outlet.

Instruction manual for the documentation program

Hardware requirements
Mouse: serial
PC: AT,386,486,586.
Graphics: EGA,VGA.
COM 1 interface.
ICC with V24 interface with 8251 and TOSLINK optocoupler interface.

Connection to ICC (9 pin Sub-D connector) and to PC (COM 1 connector)

PIN 1: Ground PIN 7: Ground
PIN 3: TxT PIN 3: TxT
PIN 2: RxT PIN 2: RxT

8-2
Protocol parameters
Baud rate: 19,200
Start bit: 1
Data bit: 8
Stop bit: 1
Parity: even, no

Software installation
Two files are provided, ICC3.EXE and EGAVGA.BGI.
EGAVGA: graphic driver.
ICC3.EXE: ICC 350 documentation program.
Program start with ICC3.exe

IMPORTANT
The program only runs reliably in DOS.

ICC 350 incision image program

The activation time for the incision image registration is 32 seconds max.. If activated for longer,
the messages “Protocol error“ and ERROR 73 appear.

Function keys in the main menu

F1 or F8: Incision management.
The incisions are automatically numbered in sequence. In incision management, an incision
can be loaded using F1. The incision data and the unit settings are displayed in the main menu
for the loaded incision.
F3: Activation readiness.
The PC is ready to receive incision data. The ICC and the PC constantly check the incision
location. As soon as the connection is OK, the message “ICC connection OK“ appears and a
point is seen on the seven-segment display for the ICC program number.
F9: Incision image display.
With F9, the diagram for the displayed incision number is shown.
F10: Quit.
Program end.

Function keys in the incision image display

In the upper half, the program shows a sectional enlargement. The section shown is marked in
the lower half by two vertical lines. The section can be shifted using the mouse or the cursor
keys.

F1: Display diagram HF output voltage ON or OFF.

The voltage is displayed in effective volts.

F2: Display diagram HF output current ON or OFF.

The actual output current is displayed in mA.

F3: Display diagram resistance ON or OFF.

The resistance is limited to 30 kOhm in the diagram.

8-3
F4: Display diagram power ON or OFF.
The actual power is calculated from current, voltage and cos f..

F5: Display diagram phase shifting ON or OFF.

Phase shifting between voltage and current
from 0..90 degrees. 0 degrees: actual. 90 degrees: capacitive.

F6: Display diagram spark measurement value ON or OFF.

The spark measurement value is between 0 and 100.

F7: Display diagram energy ON or OFF.

Energy = P+t in [Ws].
The total energy for the incision image is also displayed in the compound probability
diagram.

F8: Call-up diagram compound probability.

F10: Quit.
End, return to main menu.

Function keys in the compound probability diagram.

F1, F2, F3, F4, F8 and F9: change color.

F10: Quit.
End, return to diagram display.

8-4
9 TECHNICAL DATA, SIGNALS, DIAGRAMS

9.1 Technical data

Cutting, monopolar with automatic voltage control (AUTO CUT)

HF voltage waveform unmodulated sinusoidal alternating voltage
Crest factor C, at RL = 500 ohms C = 1.4 for all setttings
Rated frequency 330 kHz
Maximum HF voltage at load resistance RL = ∞ 650 VP
Dynamic internal impedance in rated load range 0 ohm
Constancy of the HF voltage at RL> 350 ohms automatically controlled
Cutting quality 4 coagulation effects selectable by key
Constancy of the 4 coagulation effects automatically controlled
HF rated power 300 watts at RL = 500 ohms
HF power limitation 1 to 300 watts in 1 watt steps
Setting of the HF power limitation via up/down keys
Display of the HF power limitation 7-segment display, 3 decimal places
Precision of the HF power limitation +/- 1 digit or +/- 15%
Activation of the Cutting mode by key or pedal
HF connecting sockets 2, electronically locked from one another

Cutting, monopolar with automatic arc control (HIGH CUT)

HF voltage waveform unmodulated sinusoidal alternating voltage
Crest factor C, at RL = 500 ohms C = 1.4 for all setttings
Rated frequency of the HF voltage 330 kHz
Maximum HF voltage at load resistance RL = ∞ 570 VP
Constancy of the intensity of the electric arc automatically controlled
Cutting quality 4 coagulation effects selectable by key
Constancy of the 4 coagulation effects automatically controlled
HF rated power 300 watts at RL = 500 ohms
HF power limitation 1 to 300 watts in 1 watt steps
Setting of the HF power limitation via up/down keys
Display of the HF power limitation 7-segment display, 3 decimal places
Precision of the HF power limitation +/- 1 digit or +/- 15%
PPS (Power Peak System) yes
Activation of the Cutting mode by key or pedal
HF connecting sockets 2, electronically locked from one another

Cutting, monopolar with automatic voltage control (Program "b")

HF voltage waveform unmodulated sinusoidal alternating voltage
Crest factor C, at RL = 500 ohms C = 1.4 for all setttings
Rated frequency 330 kHz
Maximum HF voltage at load resistance RL = ∞ 550 VP
Dynamic internal impedance in rated load range 0 ohm
Constancy of the HF voltage at RL> 350 ohms automatically controlled
Cutting quality 4 coagulation effects selectable by key
Constancy of the 4 coagulation effects automatically controlled
HF rated power 120 watts at RL = 125 ohms
HF power limitation 1 to 100 watts in 1 watt steps
Setting of the HF power limitation via up/down keys
Display of the HF power limitation 7-segment display, 3 decimal places
Precision of the HF power limitation +/- 1 digit or +/- 15%
PPS (Power Peak System) yes
Activation of the bipolar cutting mode pedal
HF outlet socket bipolar

9-1
CUTTING / ENDO CUT
Automatic arc-triggered, fractionated incision
Basic setting ton = 50 ms, toff = 750 ms

Soft coagulation (SOFT COAG)

HF voltage waveform unmodulated sinusoidal alternating voltage
Crest factor C, at RL = 500 ohms C = 1.4 for all setttings
Rated frequency of the HF voltage 330 kHz
Peak value of the HF voltage max. 1900 VP
Constancy of the HF voltage automatically controlled
HF rated power 120 watts at 125 ohms
HF power limitation (PHFmax.) from 1 watt to 120 watts in 1 watt steps
Setting of the HF power limitation via up/down keys
Display of the HF power limitation 7-segment display, 3 decimal places
Precision of the HF power limitation +/- 1 digit or +/- 15%
Activation of the Cutting mode by key or pedal
HF connecting sockets 2, electronically locked from one another

Forced coagulation (FORCED COAG)

HF voltage waveform pulse-modulated alternating voltage
Crest factor C, at RL=500 ohms C = 5 at 120 Wmax, C = 11 at 5 Wmax
Rated of the HF voltage 1 MHz
Peak value of the HF voltage Version 1 max. 1,300 Vp
Peak value of the HF voltage Version 2 max. 2,300 Vp
Peak value of the HF voltage Version 3 max. 2,300 Vp
Peak value of the HF voltage Version 4* max. 2,600 Vp
HF rated power 120 watts at RL=350 ohms
HF power limitation from 1 watt to 120 watts in 1 watt steps
Setting of the HF power limitation via up/down keys
Stability of the HF power see Diagram Forc. Coag. power via RL
Display of the HF power limitaiton 7-segment display, 3 decimal places
Precision of the HF power limitation +/- 1 digit or +/- 15%
Activation of the Forced coagulation by key or pedal
HF connecting sockets 2, electronically locked from one another

Spray coagulation (SPRAY COAG)

HF voltage waveform pulse-modulated alternating voltage
Crest factor C, at RL=500 ohms C = 7 at 120 Wmax, C=15 at 5 Wmax
Rated frequency of the HF voltage 1 MHz
Peak value of the HF voltage max. 4 kVP
HF rated power 120 watts at 500 ohms
HF power limitation from 1 watt to 120 watts in 1 watt steps
Setting of the HF power limitation via up/down keys
Display of the HF power limitation 7-segment display, 3 decimal places
Precision of the power limitation +/- 1 digit or +/- 15%
Activation of the Spray coagulation by key or pedal
HF connecting sockets 2, electronically locked from one another

*) not ICC 350 T, Z

9-2
Bipolar coagulation (AUTO BIPOLAR)
HF voltage waveform unmodulated sinusoidal alternating voltage
Crest factor C, at RL=500 ohms C = 1.4 for all settings
Rated frequency 330 kHz
Peak value of the HF voltage 190 VP max
Constancy of the HF voltage at RL > 50 ohms automatically controlled.
HF rated power 120 watts at 125 ohms
HF power limitation (PHFmax.) from 1 watt to 120 watts in 1 watt steps
Setting of the HF power limitation via up/down keys in 1 watt steps
Display of the HF power limitation 7-segment display, 3 decimal places
Precision of the HF power limitation +/- 1 digit or +/-15%
Activation of the Bipolar coagulation by pedal or Auto Start
Auto Start delay 0 = 0 sec., 1 = 0.5 sec., 2 = 1 sec. selectable
Auto Stop ON/OFF by key
HF connecting socket 1

Safety features
Protection class according to EN 60 601-1 I
Type according to EN 60 601-1 CF
Switching of the neutral electrode can be changed over: capacitive grounding or floating
output
Monitoring of single-surface neutral electrodes Automatic monitoring of the electrical connection
between the neutral electrode and high-frequency
surgical unit
Monitoring of dual-surface neutral electrodes Automatic monitoring
a) of the electrical connection between the neutral
electrode and high-frequency surgical unit
and
b) between the neutral electrode and patient
c) of the symmetry of the HF partial currents iHF1 /
iHF2
d) of the HF current IHF as a function of the contact
resistance Rü between the partial surfaces of the
neutral electrode
Max. resistance Rü between the partial surfaces and of 120 ohms ± 20 ohms
a divided neutral electrode
Warning signals Sw as a function of IHF and Rü see Diagram Sw = f ( IHF , Rü )
Monitoring of the HF output parameters HF voltage, HF current, HF power
Error display in safety field
Limitation of the max. HF power adjustable
Auto. limitation of the max. activation time limit yes, display in safety field
Auto. performance check Self check after switching on the unit
Automatic monitoring of LF leakage currents in a yes, warning signals as of 0.05 mA
monopolar applied part with a capacitively grounded
neutral electrode
Automatic monitoring of the HF leakage currents in a yes, warning signals as of 150 mA
monopolar applied part

Programmability
Program 0 Programmed by the manufacturer
Program 1 to 9 Custom programmable by the user
Program "b" = bipolar Cutting/Coagulation Custom programmable by the user
Program "E" = Endo Cut Custom programmable by the user
Programming Via keys on the front panel
Program storage Via keys on the front panel
Program call-up Via keys on the front panel

9-3
Documentation
Automatic storage of operating errors yes
Automatic storage of function errors yes
Automatic storage of safety errors yes

Power connection
Rated power voltage 240 V / 230 V / 115 V / 110 V / 100 V ± 10 %
Rated power frequency 50 / 60 Hz
Power current 4.0 A at 230 - 240 V / 8.0 A at 100 - 115 V
Power consumption in Standby mode 25 watts
Power consumption at max. HF power 620 watts
920 VA
Current consumption in Standby mode 150 mA at 230 - 240 V / 300 mA at 100 - 115 V
Potential equalization terminal yes
Power fuses 2 slow burn, 4 A at 230 - 240 V / 8 A at 100 - 115 V

Classification according to EC Directive 93/42/EEC

Class IIb

Dimensions, weight
WxHxD 410 x 152 x 368 mm
Weight 10 kg

Environmental conditions for shipping and storage of the unit

Temperature -40°C to + 70°C
Air humidity, relative 30% to 95%

Environmental conditions for operation of the unit

Temperature +10°C to + 40°C
Air humidity, relative 30% to 75%, noncondensing

9-4
9.2 Visual and acoustic signals

STATUS visual acoustic HF off

Power switch on •
Operating error on the front panel •• •• ••
HF generator on •• ••
LF leakage current greater than 0.05 mA •• •• ••
Error No.5
HF leakage current greater than 150 mA, but less than 300 mA •• red
HF leakage current greater than 300 mA •• red ••
Error No. 17
Output error •• red •• ••
Max. activation time limit reached •• red
Max. activation time limit exceeded too long •• red •• ••
No neutral electrode connected to the unit •• red •• ••
Error No.13
Single-surface electrode connected to the unit • green
Dual-surface neutral electrode connected to unit and contact • green
resistance between the contact surfaces less than 120 ohms
Dual-surface neutral electrode not applied to patient or contact •• red •• ••
resistance between the contact surfaces and patient greater than 120 Error No.13
ohms
HF current relative to the contact resistance between the contact •• red •• 4 times
surfaces of a dual-surface neutral electrode and patient too great Error No.19
HF partial currents of the contact surfaces of a dual-surface neutral •• red
electrode different
HF partial currents of the contact surfaces of a single-surface neutral •• red •• ••
electrode too different Error No.21
Interruption of the line between unit and neutral electrode or between •• red •• ••
patient and dual-surface neutral electrode during HF activation Error No.13
Auto Stop for Auto Coagulation •• ••
Activation error •• •• ••
Error message upon error recognition during self check • • •

• These signals are produced regardless of whether the unit is activated or not activated.
•• These signals are produced only if the unit is activated.

9-5
9.3 Diagrams
AUTO CUT MODE, Effect 1, 2, 3, 4
BIPOLAR CUT MODE

Peak value of the HF output voltage UHF at no load, as a function of the power limitation Pmax
for EFFECT 1 to 4.

Power limitation in
BIPOLAR CUT MODE

9-6
HIGH CUT, Effect 1, 2, 3, 4
Peak value of the HF output voltage UHF at no load, as a function of the power limitation Pmax
for EFFECT 1 to 4.

9-7
SOFT COAGULATION
AUTO BIPOLAR
Peak value of the HF output voltage UHF at no load, as a function of the power limitation Pmax.

9-8
FORCED COAGULATION (For. 4 not ICC 350 T, Z)
Peak value of the HF output voltage UHF at no load, as a function of the power limitation Pmax.

9-9
SPRAY COAGULATION
Peak value of the HF output voltage UHF at no load, as a function of the power limitation Pmax.

9-10
CUT MODE, Effect 1, 2, 3, 4
Power output as a function of load resistance
for power limitation of 300 watts

9-11
CUT MODE, Effect 1, 2, 3, 4
Power output as a function of load resistance
for power limitation of 150 watts

9-12
HIGH CUT, Effect 1, 2, 3, 4
Power output as a function of load resistance
for power limitation of 300 watts

9-13
HIGH CUT, Effect 1, 2, 3, 4
Power output as a function of load resistance
for power limitation of 150 watts

9-14
SOFT COAGULATION
AUTO BIPOLAR
Power output as a function of load resistance for
1) power limitation of 120 watts
2) power limitation of 60 watts

9-15
FORCED COAGULATION
Power output as a function of load resistance for
1) power limitation of 120 watts
2) power limitation of 60 watts

9-16
SPRAY COAGULATION
Power output as a function of load resistance for
1) power limitation of 120 watts
2) power limitation of 60 watts

9-17
BIPOLAR CUT MODE
Power output as a function of load resistance for
1) power limitation of 100 watts
2) power limitation of 50 watts

9-18
AUTO CUT MODE, Effect 1, 2, 3, 4
Power output as a function of the power limitation

RL = 500 ohms

9-19
HIGH CUT, Effect 1, 2, 3, 4
Power output as a function of the power limitation

RL = 500 ohms

9-20
SOFT COAGULATION
AUTO BIPOLAR
Power output as a function of the power limitation

RL = 125 ohms

9-21
FORCED COAGULATION
Power output as a function of the power limitation

RL = 350 ohms

Forced 1, 2, 3, 4

9-22
SPRAY COAGULATION
Power output as a function of the power limitation

RL = 500 ohms

9-23
NESSY
Dependence of the warning signals on contact resistance Rü between the two contact surfaces of
a divided neutral electrode and the HF current IHF flowing through the entire surface of the
neutral electrode:

A = In this range, IHF is sufficiently small relative to Rü. No warning signal.

B = In this range, IHF is too large relative to Rü. The HF generator can be activated, however a
red warning signal and four warning tones are given after each activation of the HF generator.
In this condition, the unit must continue to be used only in emergency cases.

C = In this range, Rü is greater than 120 ohms. The HF generator cannot be activated. After
every activation attempt, a red warning signal and warning tones are given.

9-24
10 INSTALLATION

10.1 Spatial requirements

High-frequency surgery units must only be operated in medically used rooms. The spatial
requirements, in regard to electric installation, affect e.g. the grounded conductor system, the
ground fault interrupt system, as well as measures for preventing electrostatic charges.

The unit is used in rooms in which personnel can pick up electrostatic charges, for example in
rooms with electrically nonconductive floors, thus touching the front panel of the units can lead
to a brief illumination of light diodes or seven-segment displays due to discharge of an electrostatic
charge. However, this occurrence does not change the settings on the front panel.

10.2 Set-up possibilities in the operating room

ICC model series units can be set up in principle on tables, consoles on ceiling suspensions or
wall- mounted arms, as well as on special equipment carts.

10.3 Power connection

High-frequency surgical units must only be connected via the power cord provided by the unit
manufacturer or one of equal quality equipped with the national test symbol to a correctly installed
hospital grade power socket. Here, no outlet power socket or extension cord should be used if
possible for reasons of safety. If their use is unavoidable, these must be equipped with a protective
ground in perfect working order. The power outlet must be secured with a fuse with at least 10 A
rated current.

10.4 Potential equalization

If necessary, the unit can be connected to the potential equalization of the room. This should
prevent low-frequency electrode currents, e.g. low-frequency leakage currents in a defective
protective ground system, from endangering the patient.

ICC model series units are equipped with a potential equalization connector on the unit back
panel according to DIN 42 801. In this way, the units can be connected via a potential equalization
line to a potential equalization terminal at the set-up location.

10.5 Explosion protection

High-frequency surgical units intentionally generate electric sparks between an active electrode
and tissue. Electric sparks may also result within the unit. For this reason, high-frequency surgical
units must not be used in areas where there is a danger of explosion. Considered as explosive is
the area up to 20 cm above the floor and the area around and below the operating table, if
flammable or explosive cleaning agents, disinfectants, anesthetics, etc. are used. High-frequency
surgical units are normally installed outside the zone designated as potentially explosive.

WARNING

Footswitches are used within the potentially explosive area nevertheless and must therefore be
designed as explosion-protected.

10-1
10.6 Protection against moisture
ICC model series high-frequency surgical units are protected against the penetration of moisture
in accordance with EN 60 601-2-2 . In spite of this, these units should not be set up in the
vicinity of hoses or containers which contain liquids. Liquids should not be placed above or
even on the unit. Only those footswitches may be used which are watertight in accordance with
EN 60 601-2-2 Sec. 44.6 aa. Only those electrode handles with key switches must be used which
conform to the EN 60 601-2-2, Sec. 44.6 bb.

10.7 Cooling
ICC model series units must be set up in such a way that free air circulation around their housing
is ensured. For that reason, set-up in confined corners, shelves etc. is not permissible.

10.8 HF interferences
High-frequency surgical units intentionally generate high-frequency voltages and currents. It
must therefore be taken into consideration during set-up and operation that other electromedical
equipment may be subjected to interference in their function.

10.9 Combination with other units

If an ICC is to be operated in combination with other units, make certain that the correct functions
and the safety of the units are not impaired by this combination.

For combination of an ICC with an Argon Plasma Coagulation unit, the instruction manual for
the Argon Plasma Coagulation must also be precisely observed.

10.10 Receiving inspection

The unit should be checked immediately upon receipt for shipping damage and be subjected to
a performance test. In case of damage due to shipping, this must be immediately reported to the
shipping agent and a damage report must be filled out to secure the claim for damage
compensation. This must include, in addition to the name and address of the recipient, the date
of receipt, type and serial number of the unit supplied, as well as a description of the damages.

The unit’s original packaging should be retained during the guarantee period so that the unit can
be returned in the original packaging if this becomes necessary.

10.11 Custom adaptation of the maximum time limit

In consideration of the risk of thermal tissue damages due to unintentional switching on of an
HF high-frequency generator, an unintentionally switched on HF generator should be switched
off again as soon as possible automatically. Since the unit cannot automatically distinguish between
intentional and unintentional switching on of an HF generator, the automatic switching off of an
HF generator must not occur too quickly, because this would impair the operator during cutting
and/or coagulation. Since the risk of thermal tissue damage varies greatly among the various
operating modes, the units of the ICC model series can adapt and store the maximum time limit
for each operating mode and in each storable program via Test program no. 10 of at least 3 sec.
to a maximum of 900 sec.

10-2
Instructions for custom adaptation of the maximum time limit
1. Call up Test program 10 as follows:

2. Press key 2.1 with the unit switched off and switch on the power.
Pr. = Program appears in Display 2.3
The program number, e.g. 1, appears in Display 3.6.

3. By pressing key 3.5 Ý, program no. 10 is set and

4. by pressing key 2.1, this program is activated.

The red signal lamp “Time limit” is illuminated and the respective maximum time limit
appears in the displays on the function fields.

5. By pressing the Ý or ß key beneath the respective display, the maximum time limit for
each function field can be adjusted individually from 3 to 900 seconds.

6. By pressing key 6.1, the set maximum time limits are stored. The maximum time limits for
all programs, selected by key 6.2, can be set and stored independent of one another.

7. By pressing key 2.1, Test program 10 can be deactivated.

8. It is possible to end the Test mode by switching off the power switch.

WARNING

For safety reasons, a change in the automatic limitation of the maximum time limit must only be
made if all users of this unit are informed properly and in good time about this change.
In addition, a change in the automatic limitation of the maximum time limit must be properly
documented.

10-3
10.12 Versions of Forced coagulation
For Forced coagulation, the ICC produces brief voltage pulses with a high peak voltage. In this
way, an efficient hemostasis is achieved even with very small-surface electrodes, such as with
TUR resection loops or laparoscopic retractors. However, these voltage pulses can cause more
or less intensive disturbances in other electronic equipment, such as in video monitors. The
Forced coagulation of the ICC can therefore be adapted via Test program 12 in regard to the
maximum adjustable peak value of the voltage pulses according to the respective application
purpose. Four different versions of Forced coagulation are available for selection:

Version 1 (Standard version)

In this version, the peak value of the voltage pulses increases as a function of the power limitation
in the range from 1 watt to 30 watts continuously to 1,300 Vp . Above 30 watts power limitation,
the peak value of the voltage pulses is limited to a maximum of approx. 1,300 Vp . This standard
version is set and stored on all units in the ICC model series.

Version 2
In this version, the peak value of the voltage pulses continuously increase to 2,300 Vp as a
function of the power limitation in the range of 1 watt to 80 watts.

Version 3
In this version, the peak value of the voltage pulses increase continuously to 2,300 Vp as a
function of the power limitation in the range of 1 watt to 30 watts. Above 30 watts power limitation,
the peak value of the voltage pulses is limited to a maximum of approx. 2,300 Vp.

Version 4 (not ICC 350 T, Z)

In this version, the peak value of the voltage pulses increase continuously to 2,600 Vp as a
function of the power limitation in the range of 1 watt to 30 watts. Above 30 watts power limitation,
the peak value of the voltage pulses is limited to a maximum of approx. 2,600 Vp.

WARNING

The currently selected version of Forced coagulation applies to the AUTO COAG 1 function
field, AUTO COAG 2 function field and to the programs. The selected version of Forced
coagulation can be stored. If Version 2, 3 or 4 is stored, the unit briefly displays the current
version every time after the power switch is switched on. Standard version 1 is not displayed.
In addition, any change of the version of Forced coagulation must be properly documented.

10.13 Versions of neutral electrode switching

The ICC neutral electrode can be operated either as capacitively grounded or insulated to ground
potential. The currently selected operating mode is displayed on the front panel. The operating
mode can be switched over by the Technical Service.

10-4
11 CLEANING AND DISINFECTION OF THE UNIT

11.1 Cleaning and disinfection of the unit

The unit housing should only be cleaned and disinfected with nonflammable and nonexplosive
agents. Make certain here that no moisture penetrates into the unit.

We recommend a spray or wipe-down disinfection. However, the information from the disinfectant
manufacturer absolutely must be observed here.

WARNING

If cleaning or disinfection of the unit with flammable or explosive agents unavoidable, this must
be completely evaporated from the unit before switching on the unit.

Use no alcohol or disinfectant products with an alcohol base. The surface coating on the front
plate may become detached.

11-1
11-2
12 PERFORMANCE CHECKS
Before every application, the user should check the functional efficiency of the unit and the
accessories. The ICC is equipped for this with various automatic performance checks that, each
time the power switch is switched on, proceed briefly and thus signal and display recognized
errors. However, not all possible errors are automatically detected and displayed.

12.1 Automatic performance test after switching on the unit

Each time after switching on, the unit goes through an automatic performance check. If
performance errors are detected here, these errors are signaled acoustically and an error number
assigned to the respective error is displayed. The following performance errors of the unit and of
accessories connected to the unit can be automatically recognized:

1. If a key on the front panel is depressed or shorted out due to an error once the power switch
is switched on, this error is signaled acoustically after switching on the power switch and
displayed by an error number.

2. If a key on the electrode handle is shorted out or bypassed at low resistance (e.g. due to
moisture in the electrode handle) due to an error or depressed while the power switch is
switched on, this error is signaled acoustically after the power switch is switched on and
displayed by an error number.

3. If the contact of a footswitch is shorted out due to an error or if a pedal is stuck or a pedal
is pushed while the power switch is switched on, this error is signaled acoustically and
displayed by an error number.

12.2 Automatic performance check during activation

After every activation, the unit goes through an automatic performance check. If performance
errors are determined here, these errors are acoustically signaled and an error number assigned
to the respective error is displayed. The following performance errors of the unit and before
accessories connected to the unit are automatically recognized:

12.2.1 Check of the HF output voltage

If the HF output voltage deviates from the set HF output voltage when activating a certain
operating mode, e.g. CUTTING or SOFT COAGULATION, the unit produces visual and acoustic
warning signals.

12.2.2 Automatic check of the neutral electrode

If during activation, the connection to the neutral electrode is interrupted, or if the contact resistance
(only for a divided neutral electrode) is too high, the unit switches the HF generator off, produces
an acoustic warning signal and displays the error by an error number.

12-1
12.3 Automatic error documentation
The ICC is equipped with an automatic error recognition, error signaling and error documentation
device. Errors are recorded which are present or occur during the switching on of the power
switch, during the Self Check after switching on the power switch, during tests or during activation
of the unit and/or of accessories connected to the unit. The smaller errors recognized by the unit
are only signaled visually, larger errors are signaled visually and also acoustically. The various
errors recognized by the unit are assigned error numbers. If an error occurs, it is not only
immediately signaled visually and/or acoustically, but also the corresponding error number is
stored in the unit, where it then also remains stored once the unit has been switched off. The last
10 error numbers can be called up as follows via Test program number 2 at any time.

Calling up the stored error numbers via Test program 2:

a) Press key 3 while the unit is switched off and switch on the power switch.
· Pr (Program) appears in the AUTO CUT display
· 1 appears in the AUTO COAG 1 display

b) Select program no. 2 by pressing key 8

· 2 appears in the AUTO COAG 1 display.

c) Test program no. 2 is activated by pressing key 3.

· Err (Error) appears in the AUTO CUT display.
· 1 (error memory location no. 1) appears in the AUTO COAG 1 display.
· The error number stored at error memory location 1 appears in the AUTO BIPOLAR
display.

d) In the error list, the various errors for the error numbers are described.

e) By pressing keys 8 or 9, the 10 error memory locations available can be called up.
· The number of the current error memory location appears in the AUTO COAG 1 display.
· The current error number appears in the AUTO BIPOLAR display.

f) By pressing key 7, the error numbers on all error memory locations can be deleted.

12-2
 Error list
Error Error How to proceed?
No.
0 No error
1 No HF output voltage Notify the Technical Service
2 HF output voltage too high Notify the Technical Service
3 No HF output voltage Notify the Technical Service
4 HF output voltage too high Notify the Technical Service
5 LF leakage current greater than 0.05 mA Notify the Technical Service
6 Activation error Notify the Technical Service
7 Activation error Notify the Technical Service
9 Time limit exceeded Heed maximum time limit
10 Erroneous setting of the AUTO CUT Before activation of a cutting mode, the AUTO CUT
function field during activation function field must be completely set
11 Erroneous setting of the AUTO COAG 1 Before activation, the AUTO COAG 1 or AUTO
or AUTO COAG 2 function field during COAG 2 function field must be completely set
activation
12 Erroneous setting of the AUTO Before activation, the AUTO BIPOLAR function field
BIPOLAR function field during must be completely set
activation
13 The contact surface between the neutral Use a sufficiently large neutral electrode and apply to
electrode and the patient is too small or the entire surface.
the neutral electrode was not connected to
the unit.
This error is recognized and reported in Check the connection of the neutral electrode to the
the Standby mode or during activation of unit.
the unit.

Only for NESSY Version 2 Check the connection between the neutral electrode
Error in the connection between the and unit. Probably a faulty cable or faulty plug
neutral electrode and unit

Only for NESSY Version 3 Eliminate short or exchange cable

Short between the two contact surfaces of
a divided neutral electrode or in the cable
to the neutral electrode
17 HF leakage current greater than 300 mA Check whether the neutral electrode was correctly
applied and make certain that the patient has no
contact with electrically conductive objects.
18 HF leakage current greater than 150 mA Check whether the neutral electrode was correctly
applied and make certain that the patient has no
contact with electrically conductive objects.
19 The contact surface between the neutral Use a sufficiently large neutral electrode and apply to
electrode and the patient was too small the entire surface.
20 The neutral electrode was applied in the See Chapter 4.4.5
incorrect direction NESSY
21 The neutral electrode was applied in the See Chapter 4.4.5
incorrect direction NESSY
22 When switching on the power switch, the Check whether there was an operating error or
yellow pedal on the footswitch or the whether the yellow pedal of the footswitch or the
yellow key on the electrode handle was yellow key on the electrode handle is defective
already pressed

12-3
 23 When switching on the power switch, the Check whether there was an operating error or
blue pedal on the footswitch or the blue whether the blue key on the electrode handle or the
key on the electrode handle was already cable to the electrode handle is defective
pressed for CUT/COAG 1
24 When switching on the power switch, the Check whether there was an operating error or
blue pedal on the footswitch or the blue whether the blue pedal is defective
key on the electrode handle was already
pressed for CUT/COAG 2
25 When switching on the power switch, the Check whether there was an operating error or
blue pedal on the dual-pedal footswitch whether the blue pedal of the dual-pedal footswitch or
or the white pedal on the single-pedal the white pedal of the single-pedal footswitch is
footswitch was already pressed defective
26 When switching on the power switch, Always make certain that bipolar or monopolar active
there was already an electrically electrodes or instruments are laid down on electrically
conductive connection between the two nonconductive surfaces
poles of the bipolar instrument
27 The internal temperature of the unit was Always set up the unit in such a way that air can reach
too high. The maximum HF power was the housing. If this error number appears, the unit may
automatically reduced. continue to be used if the reduced power is sufficient
for the respective operation
28 to 29 These errors concern functions in the unit Please notify the Technical Service
30 The load resistance of the unit was too Either the contact surface of the active electrode was
low too large or the power limitation set too low, or there
was contact between an active electrode and a metallic
instrument, e.g. trocar sheath.
31 The HF generator of the unit was The unit can briefly supply more than 300 watts
overloaded too long. The maximum power. More than 400 watts, averaged over 1 second,
power output was automatically reduced. are not permitted for reasons of safety.
32 to 35 These errors affect functions in the unit Please notify the Technical Service
36 The Auto Start key was pressed while the Always first set the required activation mode and then
coagulation electrode was already apply the coagulation electrode to the tissue to be
touching the tissue coagulated
37 This error concerns functions in the unit Please notify the Technical Service
38 Short between the two poles of a bipolar Avoid shorts
instrument, i.e. a bipolar forceps
40 to 49 This error concerns functions in the unit Please notify the Technical Service
50 to 51 Error in a front panel key Please notify the Technical Service
71 to 76 These errors concern the serial interface Please notify the Technical Service
on units that are equipped with a serial
interface
80 to 91 These errors concern units with built-in
Neurotest
81 Technical error in the intensity setting Please notify the Technical Service
82 Neutral electrode missing or too small Check neutral electrode
83 Pulse current somewhat too high,
however still within the tolerance limits
84 Pulse current too high Please notify the Technical Service

12-4
85 No pulse current Check whether there was an interruption in the
connecting cables or whether the active or neutral
electrode was not applied
86 No pulse current Check whether there was an interruption in the
connecting cables or whether the active or neutral
electrode was not applied. If neither of these errors
was found, then please contact the Technical Service
87 Pulse current too low, however still
within tolerance limits
88 Maximum time limit exceeded Reactivate if necessary
89 The Neurotest is already activated when Always switch on unit and activate after the automatic
the unit is switched on self check and confirmation of the front panel setting
90 Electronic fuse for prevention of Please notify the Technical Service
unpermissibly high currents is triggered
91 Technical error Please notify the Technical Service
CAUTION
This error list contains error descriptions relevant only to the operator. Errors that concern the Technical
Service are described in the technical service documentation.

12-5
12-6
13 SAFETY CHECKS

To prevent a reduction in safety for the unit due to age, wear etc., § 6 of the regulation concerning
the installation, operation and use of active medical products (BetreibVaMP) prescribes regular
safety checks. The operator must have the safety checks which have been established for this
unit properly performed to the prescribed extent. The safety checks must only be done by the
manufacturer or by persons expressly authorized by him.

The following safety checks have been established for the ICC :
· Inspection of inscriptions and instruction manual

· Visual inspection of the unit and accessories for damage

· Inspection for electrical safety according to EN 60 601-1, Part 1

a) Grounded conductor inspection
b) Leakage current inspection

· Performance test of all switches and control lamps on the unit

· Inspection of the monitoring devices

· Inspection of the automatic start mode

· Measurement of power output in the CUT operating mode.

· Measurement of power output in the COAGULATE operating mode.

· Measurement of the high-frequency capacities in the various operating modes

· The high-frequency surgical unit must undergo a safety check at least once a year.

The results of these safety checks must be entered in the medical product logbook.

If deficiencies are found during the safety checks, by which patients, employees or third parties
could be endangered, the unit must not be operated until these deficiencies have been rectified
by a professional technical service.

13-1
13-2
14 MAINTENANCE, CARE AND DISPOSAL OF THE UNIT
14.1 Maintenance of the unit including reusable accessories
Maintenance of the unit including the reusable accessories includes preventive and corrective
measures for servicing. Therefore established, regularly performed safety checks (see Chapter
9) represent preventive measures, while changes and repairs can be summarized under the category
of corrective maintenance. Through regular maintenance, the unit including the reusable
accessories should be kept within the required status specified in the technical data, and operational
readiness and safety are guaranteed for this until the next maintenance date.

14.1.1 Changes and repairs

Changes and repairs must not reduce the safety of the unit and its accessories for the patient, the
user and the surroundings. This is considered fulfilled if structural and functional features have
not been changed at the expense of safety (DIN 57 751-1/VDE 0751-1). Changes and repairs to
the unit, in consideration of the special safety requirements for high-frequency surgical units,
must only be performed by the manufacturer or by persons expressly authorized to do this by
him. If unauthorized persons perform improper changes or repairs to the unit or accessories, the
manufacturer assumes no liability. Additionally in this case, the guarantee claim becomes void.

14.2 Care of the unit

Effective protection of the unit from damage also includes, in addition to proper operation and
maintenance, the safe set-up of the unit. This also includes, in addition to safe fixation of the unit
to its base, its protection from moisture, contamination and contact with flammable or explosive
substances. To ensure good radiation of unit heat resulting from operation, air circulation around
the cooling fans and the heat sink must not be impeded.

14.3 Disposal of the unit

The unit can be disposed of at the end of its useful life as standard electronic scrap.

14-1
14-2
15 CONDITIONS OF GUARANTEE

15.1 Customer service

If you are interested in a service contract, please contact ERBE Elektromedizin or an authorized
retailer. Do you have questions regarding high-frequency surgery, the ICC or on this instruction
manual? Wish you like the latest scientific publications on high-frequency surgery? Please contact
an ERBE employee or your local branch office. We would be glad to help you.

15.2 Conditions of guarantee

The unit and accessories must be immediately examined upon receipt for defects and shipping
damage. Claims for damage compensation in this regard are only considered valid if the Seller
or Shipping agent is immediately notified. A damage report must be filled out.

The term of guarantee for the ICC is 1 year, for accessory parts 6 months, calculated from the
date of delivery. A claim of guarantee can only be made when the properly completed guarantee
certificate is presented.

The scope of the guarantee encompasses no-cost repair of the unit, provided the damage was
caused by a material or manufacturing error. Other claims, particularly claims of damage
compensation, are excluded.

Repair must only be performed by ERBE, one of our representatives, or by an authorized retailer.
The claim of guarantee becomes void if improper changes or repairs were made.

Through guarantee performances, the guarantee is neither extended nor renewed.

15-1
15-2