HT-RT3 SA-WRT3

SERVICE MANUAL US Model

Canadian Model
Ver. 1.5 2017.09
AEP Model
UK Model
• All the units included in the HT-RT3 (SA-WRT3, E Model
SS-RT3/SRT3, remote control) are required to
confirm the operation of SA-WRT3. Check in Australian Model
advance that you have all the units.

Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.

COMPONENT MODEL NAME

HT-RT3
Bar Speaker (Speaker System) SS-RT3
Surround Speaker (Speaker System) SS-SRT3
Subwoofer (Active Subwoofer) SA-WRT3
• The service manual for SS-RT3/SRT3 has been issued separately.
Please refer to the service manual for information.

SPECIFICATIONS
2)
Amplifier section HDMI section BLUETOOTH standard profiles (When “CTRL” in “HDMI>”
US models: Connector indicate the purpose of BLUETOOTH or “BTSTB” in “BT >” is set to
POWER OUTPUT AND TOTAL Type A (19pin) communication between devices. “ON”)
HARMONIC DISTORTION: USB section 3)
Codec: Audio signal compression and Dimensions (w/h/d) (approx.)
(FTC) (USB) port conversion format 190 mm × 392 mm × 315 mm
Front L + Front R: Type A 4)
(7 1/2 in × 15 1/2 in × 12 1/2 in)
With 2.5 ohms loads, both channels Subband Codec Mass (approx.)
driven, from 200 Hz – 20,000 Hz; BLUETOOTH section 5)
Advanced Audio Coding 7.8 kg (17 Ib 4 oz)
rated 30 watts per channel minimum Communication system
UFOELK - 2/21/2018 5:23 PM
6)
BLUETOOTH Specification Speaker section The system will automatically enter
RMS power, with no more than Power saving mode when there is
1% total harmonic distortion from version 4.2 Speaker system
Output Subwoofer system, Bass reflex no HDMI connection and no BLUE-
250 milliwatts to rated output. TOOTH pairing history, regardless
POWER OUTPUT (reference): BLUETOOTH Specification Speaker
Power Class 1 160 mm (6 3/8 in) cone type of the settings you have made for
Front L/Front R/Surround L/ “CTRL” in “HDMI>” and “BTSTB”
Surround R: Maximum communication range General
Line of sight approx. 25 m (82 ft)1) in “BT >”.
65 W (per channel at 2.5 ohms, Power requirements
1 kHz) Frequency band LA9 models only: Supplied accessories
Center: 2.4 GHz band (2.4000 GHz – 110 V - 240 V AC, 50/60 Hz Remote control (1)
170 W (at 4 ohms, 1 kHz) 2.4835 GHz) US, CND models only: R03 (size AAA) batteries (2)
Subwoofer: Modulation method 120 V AC, 60 Hz High Speed HDMI cable (1) (E12, LA9,
170 W (at 4 ohms, 1 kHz) FHSS (Freq Hopping Spread EA models only: AR, AUS, SP, EA)
Spectrum) 127 V – 240 V AC, 50/60 Hz Optical digital cable (1) (US, CND,
Except US models: Compatible BLUETOOTH profiles2) AEP, UK)
POWER OUTPUT (rated) Except LA9, US, CND, EA
A2DP 1.2 (Advanced Audio models: AC plug adaptor (1) (LA9)
Front L + Front R: Distribution Profile)
35 W + 35 W (at 2.5 ohms, 1 kHz, 220 V – 240 V AC, 50/60 Hz
AVRCP 1.6 (Audio Video Remote Power consumption Design and specifications are subject to
1% THD) Control Profile)
POWER OUTPUT (reference) On: 85 W change without notice.
Supported Codecs3) Standby: 0.5 W or less (Power
Front L/Front R/Surround L/ SBC4), AAC5)
Surround R: saving mode)
Transmission range (A2DP) (When “CTRL” in “HDMI>” and
65 W (per channel at 2.5 ohms, 20 Hz – 20,000 Hz (Sampling
1 kHz) “BTSTB” in “BT >” are set to
frequency 32 kHz, 44.1 kHz, “OFF”)
Center:
170 W (at 4 ohms, 1 kHz)
Subwoofer: 1)
48 kHz)
The actual range will vary depending
Standby: 2.8 W or less6)
HT-RT3
HOME THEATRE SYSTEM
170 W (at 4 ohms, 1 kHz) on factors such as obstacles between
Inputs devices, magnetic fields around a
USB microwave oven, static electricity,
ANALOG IN cordless phone, reception sensitivity,
antenna’s performance, operating
SA-WRT3
TV IN (OPTICAL)
Output system, software application, etc.
HDMI OUT (ARC)

ACTIVE SUBWOOFER
9-890-680-06
2017I33-1
© 2017.09 Sony Video & Sound Products Inc.
HT-RT3
Ver. 1.1

Copyrights and Trademarks Compatible iPod/iPhone models

• This system incorporates Dolby* Digital. The compatible iPod/iPhone models are as follows. Update your iPod/iPhone with
* Manufactured under license from Dolby Laboratories. the latest software before using with the system. BLUETOOTH technology works
Dolby and the double-D symbol are trademarks of Dolby Laboratories. with:
• The BLUETOOTH® word mark and logos are registered trademarks owned by - iPhone 6s Plus/iPhone 6s/iPhone 6 Plus/iPhone 6/iPhone 5s/iPhone 5c/iPhone 5
Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under - iPod touch (6th generation)/iPod touch (5th generation)
license. Other trademarks and trade names are those of their respective owners. • THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT
• This system incorporates High-Definition Multimedia Interface (HDMI™) PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL
technology. USE OF A CONSUMER FOR
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL
in the United States and other countries. STANDARD (“MPEG-4 VIDEO”)
• The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the
United States and in other countries. AND/OR
• Android™ is a trademark of Google Inc.
• Google Play™ is a trademark of Google Inc. (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER
• MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/
IIS and Thomson. OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PRO-
• Windows Media is either a registered trademark or trademark of Microsoft VIDE MPEG-4 VIDEO.
Corporation in the United States and/or other countries.
• This product is protected by certain intellectual property rights of Microsoft NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
Corporation. Use or distribution of such technology outside of this product is ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMO-
prohibited without a license from Microsoft or an authorized Microsoft subsid- TIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE
iary. OBTAINED FROM MPEG LA, L.L.C.
• “BRAVIA” is a trademark of Sony Corporation. HTTP://WWW.MPEGLA.COM
• “ClearAudio+” is a trademark of Sony Corporation. • All other trademarks are trademarks of their respective owners.
• “PlayStation” is a registered trademark of Sony Computer Entertainment Inc. • Other system and product names are generally trademarks or registered trade-
• Apple, the Apple logo, iPhone, iPod, iPod touch, and Retina are trademarks of marks of the manufacturers. ™ and ® marks are not indicated in this document.
Apple Inc., registered in the U.S. and other countries. App Store is a service
mark of Apple Inc. • Abbreviation
AR : Argentina model
“Made for iPod,” and “Made for iPhone” mean that an electronic AUS : Australian model
accessory has been designed to connect specifically to iPod or iPhone, respectively, CND : Canadian model
and has been certified by the developer to meet Apple performance standards. Apple E12 : 220-240 V AC area in E model
is not responsible for the operation of this device or its compliance with safety and EA : Saudi Arabia model
regulatory standards. Please note that the use of this accessory with iPod or iPhone LA9 : Latin-American model
may affect wireless performance. SP : Singapore model

2
 HT-RT3

NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
UFOELK - 2/21/2018 5:23 PM
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)

To Exposed Metal
Parts on Set

AC
0.15 μF 1.5 kΩ voltmeter
(0.75 V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.

3
HT-RT3

TABLE OF CONTENTS

1. SERVICING NOTES ............................................. 5 5-4. Printed Wiring Boards - MAIN Board - ......................... 23
5-5. Printed Wiring Boards - OLED CHUKEI PC
2. DISASSEMBLY BOAR Board - ................................................................ 24
2-1. Disassembly Flow ........................................................... 8 5-6. Schematic Diagram - OLED CHUKEI PC
2-2. Front Panel Section ......................................................... 9 BOAR Board - ................................................................ 24
2-3. Loudspeaker 16cm .......................................................... 10 5-7. Printed Wiring Board - TOUCH Board - ........................ 25
2-4. Chassis Section ............................................................... 11 5-8. Schematic Diagram - TOUCH Board - ........................... 25
2-5. BLUETOOTH Module ................................................... 11 5-9. Printed Wiring Board - SPEAKER CHUKEI PC
2-6. SPEAKER CHUKEI PC BOAR Board .......................... 12 BOAR Board - ................................................................ 26
2-7. MAIN Board, CONNECTOR Board,Switching 5-10. Schematic Diagram - SPEAKER CHUKEI PC
Regulator ........................................................................ 13 BOAR Board - ................................................................ 26
5-11. Printed Wiring Board - CONNECTOR Board - ............. 27
3. TEST MODE ............................................................ 14 5-12. Schematic Diagram - CONNECTOR Board - ................ 27
5-13. Printed Wiring Board - USB Board - .............................. 27
4. TROUBLESHOOTING ........................................... 15
6. EXPLODED VIEWS
6-1. Overall Section ............................................................... 30
5. DIAGRAMS
6-2. Chassis Section ............................................................... 31
5-1. Block Diagram - MAIN CONTROL Section - ............... 19
6-3. MAIN Board Section ...................................................... 32
5-2. Block Diagram - AUDIO Section -................................. 20
5-3. Block Diagram - POWER SUPPLY Section - ................ 21
7. ELECTRICAL PARTS LIST .............................. 33

Accessories are listed in the last part of the electrical parts list.

4
 HT-RT3
Ver. 1.3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER NOTE OF REPLACING THE IC1000 AND IC1002
Boards requiring use of unleaded solder are printed with the lead- ON THE MAIN BOARD AND THE COMPLETE MAIN
free mark (LF) indicating the solder contains no lead. BOARD
(Caution: Some printed circuit boards may not come printed with When IC1000 and IC1002 on the MAIN board and the complete
the lead free mark due to their particular size) MAIN board are replaced, it is necessary to spread the compound
between the MAIN board and the heat sink.
: LEAD FREE MARK Spread the compound (THERMAL COMPOUND (G747)) refer-
Unleaded solder has the following characteristics. ring to the figure below.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder. – MAIN Board (Component Side) –
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

ADVANCE PREPARATION WHEN CONFIRMING OP-

ERATION
All the units included in the HT-RT3 (SA-WRT3, SS-RT3/SRT3,
remote control) are required to confirm the operation of SA-WRT3.
Check in advance that you have all the units.

NOTE OF PERFORMING THE OPERATION CHECK IN

thermal compound (G747)
THE STATE THAT HEAT SINK WAS REMOVED
When performing the operation check in the state that this unit was
disassembled, it is possible to perform the operation check in the
state that heat sink was removed. But don’t perform the operation IC1000
check in the long time, and perform the operation check in the
UFOELK - 2/21/2018 5:23 PM
volume state as low as possible.
thermal compound (G747)
IF “PRTCT” APPEARS IN THE FRONT PANEL DIS-
PLAY OF THE SUBWOOFER
t Press 1 to turn off the system. After IC1002
the display turns off, disconnect the
AC power cord (mains lead) then
check that nothing is blocking the
ventilation holes of the Subwoofer.

NOTE OF REPLACING BLUETOOTH MODULE OR

RC-S730 (WW)
When the BLUETOOTH MODULE or RC-S730 (WW) is re-
placed, the MAC address for BLUETOOTH MODULE has been
changed. Please execute COLD RESET (refer to page 14) before
pairing with a Bluetooth device / NFC.

5
HT-RT3

CAPACITOR ELECTRICAL DISCHARGE PROCESSING • Parts position

When checking the board, for the electric shock prevention, con- 1. REGULATOR, SWITCHING 3L405W-2 board (Except
nect the resistors to both ends of respective capacitor (C201 and E12) (page 6)
C207) to discharge the capacitor (C201 and C207). 2. REGULATOR, SWITCHING 3L405W-3 board (E12)
(page 6)
- REGULATOR, SWITCHING 3L405W-2 Board 3. MAIN board (page 7)
(EXCEPT E12) (Conductor Side) -
- REGULATOR, SWITCHING 3L405W-3 Board 1. REGULATOR, SWITCHING 3L405W-2 board (Except
(E12) (Conductor Side) - E12)

– REGULATOR, SWITCHING 3L405W-2 Board

(EXCEPT E12) (Component Side) –

C402 T201 L101 C101 NR101 C102

C207

L401 C461 C215 C204 TH101 RC201 L102 C103

800 :/2 W

800 :/2 W

C201

C201 C207 R208 C211 T201

BOND FIXATION OF ELECTRIC PARTS

*The portion which applies bond:
When REGULATOR, SWITCHING 3L405W-2 board (Except
E12), REGULATOR, SWITCHING 3L405W-3 board (E12) or
MAIN board is replaced, it is necessary to fix parts to the boards 2. REGULATOR, SWITCHING 3L405W-3 board (E12)
by using a specified bond without fail.
– REGULATOR, SWITCHING 3L405W-3 Board
(E12) (Component Side) –
• Object boards
1. REGULATOR, SWITCHING 3L405W-2 board (Except
E12) C402 T201 L101 C101 NR101 C102
2. REGULATOR, SWITCHING 3L405W-3 board (E12)
3. MAIN board

• Use bond
Part No. Description
7-600-020-70 ADHESIVE (SC608Z2) 180ML

L401 C461 C215 C204 TH101 RC201 L102 C103

C201 C207 R208 C211 T201

*The portion which applies bond:

6
 HT-RT3
Ver. 1.1

3. MAIN board MODEL IDENTIFICATION

Distinguish by Part No. on the rear side of a main unit.
– MAIN Board (Component Side) –
– Rear View –
CN3400
MODEL NUMBER LABEL

MADE IN MALAYSIA

Destination Code
Part No.

C1008 C1009

UFOELK - 2/21/2018 5:23 PM

Model Part No.
US, CND 4-586-817-0[]
AEP 4-586-817-1[]
UK 4-586-817-2[]
AUS 4-586-817-3[]
E12 4-586-817-4[]
EA 4-586-817-5[]
SP 4-586-817-6[]
LA9 4-586-817-7[]

C1043 AR 4-586-817-8[]
C1040
• Abbreviation
AR : Argentina model
AUS : Australian model
CND : Canadian model
E12 : 220-240 V AC area in E model
*The portion which applies bond:
EA : Saudi Arabia model
LA9 : Latin-American model
SP : Singapore model

7
HT-RT3
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.

2-1. DISASSEMBLY FLOW

SET

2-2. FRONT PANEL SECTION

(Page 9)

2-3. LOUDSPEAKER 16CM

(Page 10)

2-4. CHASSIS SECTION

(Page 11)

2-5. BLUETOOTH MODULE

(Page 11)

• JIG
2-6. SPEAKER CHUKEI PC BOAR BOARD When disassembling the unit, use the following jig (for speaker
(Page 12) removal).
Part No. Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
2-7. MAIN BOARD,
CONNECTOR BOARD,
SWITCHING REGULATOR
(Page 13)

8
 HT-RT3

Note: Follow the disassembly procedure in the numerical order given.

2-2. FRONT PANEL SECTION

1 Insert a jig in two notches of bottom of the unit,
and lift the front panel section a little.

2 Insert the jig into a space and

raise front panel section.
Note 2: When using a jig,
please work so as not
to injure front panel
section and cabinet.

2 Insert the jig into a space and

raise front panel section.
Note 2: When using a jig,
please work so as
3 All bosses are removed not to injure front panel
while moving jig in the section and cabinet.
direction of the arrow,
and front panel section
is removed.

3 All bosses are removed

while moving jig in the
direction of the arrow,
total eight bosses and front panel section
is removed.

Note 1: Please spread a sheet under a

unit not to injure cabinet.
– Bottom view –

UFOELK - 2/21/2018 5:23 PM4

Ɣ*OXHVHWWLQJ
Fill in 2/3 of the bosses hole (step A
a to H)
h on the
cabinet with new glue. Ensure the front panel section
is fully inserted to cabinet. a

glue bosses hole

Glue type: Ethylene Vinyl Acetate Emulsion Adhesives

h
7 wire (flat type) (20 core) (CN5009)

c
g

6 CN3000 (5P)
f

– Front view –
e

5 Remove the front panel section

in the direction of the　arrow.

8 front panel section

Note 3: When installing the front panel section,
remove the used glue and use a new
glue to fix the front panel section.

9
HT-RT3

2-3. LOUDSPEAKER 16CM

‡ ,nVtDOODtion GireFtion Ior tKe OoXGVSeDNer ‡ :ire VettinJ front side

FP
terminal (narrow side) terminal (wide side)
loudspeaker 16cm
terminal position

5 CN1001 (4P)
loudspeaker 16cm

3 terminal
(narrow side)

1 six screws ((1) (4 x 20), +BV TAPPING)

3 terminal
– Front view –
(wide side)

2 Remove the loudspeaker 16cm

in the direction of the arrow.
4 loudspeaker 16cm

10
 HT-RT3

2-4. CHASSIS SECTION

3 Draw out chassis section in

the arrow direction.

4 chassis section

2 panel, rear (EL-SW)

– Rear view –
1 six screws (+BV TAPPING SCREW TYPE-1 3.5)

2-5. BLUETOOTH MODULE

2 one screw (+BVTP 3 x 8)

3 BLUETOOTH module

UFOELK - 2/21/2018 5:23 PM

4 two screws (+BVTP 3 x 8)

5 holder, BT

1 wire (flat type) (18 core)

– Rear view –

11
HT-RT3

2-6. SPEAKER CHUKEI PC BOAR BOARD

1 seven screws (+BVTP 3 x 8)

4 chassis, top (EL-SW) ‡:LUHVHWWLQJ

3 Draw out wire (flat type) (18 core) from
chassis, top (EL-SW).
top side
rear side

7 one screw (+BVTP 3 x 8)

wire (flat type) (18 core)

2 Remove chassis,
8 SPEAKER CHUKEI PC top (EL-SW) in the
BOAR board direction of arrow.

5 CN1002 (12P)

6 two screws
(+BV3 (3-CR))

–5HDUYLHZ–

12
 HT-RT3
Ver. 1.1

2-7. MAIN BOARD, CONNECTOR BOARD, SWITCHING REGULATOR

7 heat sink (EL-SW)

Note: When installing the heat sink (EL-SW), spread the compound referring to
"NOTE OF REPLACING THE IC1000 AND IC1002 ON THE MAIN BOARD
6 four screws AND THE COMPLETE MAIN BOARD " on page 5.
(+BVTP 3 x 8)
1 wire (flat type) (20 core) (CN2006)
0 one screw
(+BV3 (3-CR))
qg REGULATOR, SWITCHING 3L405W-2 (EXCEPT E12) /
REGULATOR, SWITCHING 3L405W-3 (E12)
8 four screws
(+BVTP 3 x 8)

qd four screws
qa CONNECTOR
(+BVTP 3 x 8)
board

2 CN101 (9P)
A

9 MAIN board

5 one screw (+B 3 x 5)

– Rear view –
A
qf Remove REGULATOR,
SWITCHING 3L405W-2 (EXCEPT E12) /
REGULATOR, SWITCHING 3L405W-3 (E12)
from holder, PC board.
3 CN3200 (2P) qs CN1 (2P)

4 one screw (+BV3 (3-CR))

• Abbreviation
E12 : 220-240 V AC area in E model

UFOELK - 2/21/2018 5:23 PM

13
HT-RT3
SECTION 3
TEST MODE
COLD RESET 4. In the state of step 3, press [%] button on the remote com-
The cold reset clears certain data in this system without initialize mander.
Personal Information and some operation data. The message will appear in order of the “V.N” → “V.MSM” on
Execute this mode when returning the unit to the customers. the screen display panel.
5. In the state of step 4, press [CLEARAUDIO+] button on the
Procedure: remote commander.
1. Touch the [1] touch key on the main unit to turn the power on. The message will appear in order of the “VAON” → “VAOFF”
2. Touch the [VOL -] touch key, [INPUT] touch key and [1] on the screen display panel.
touch key on the main unit simultaneously for five seconds. 6. In the state of step 5, press [VOICE] button on the remote com-
3. The message “RESET” appears on the screen display panel. mander to adjust the volume gain.
It can be adjusted between -3.0 to +3.0 (increase everytime 0.1
PANEL TEST step).
Eg: When gain +1.0 dB by pressing the [VOICE] button, the
Procedure: message “G +1.0” will appear on the screen display panel.
1. Touch the [1] touch key on the main unit to turn the power on. 7. In the state of step 6, press [NIGHT] button on the remote
2. Press button in order of the [u] → [DIMMER] → [m] → [M] commander to adjust the volume gain.
on the remote commander. It can be adjusted between +3.0 to -3.0 (decrease everytime 0.1
(Make the interval when each button is pressed within two sec- step).
onds). Eg: When gain -1.0 dB by pressing the [NIGHT] button, the
3. All segments in screen display panel are lighted up and then is message “G -1.0” will appear on the screen display panel.
dimmed after a second.
4. In the state of step 3, touch the [INPUT] touch key on the main Releasing method:
unit and “K 0” is displayed on the screen display panel. For software version 1.031:
5. In the state of step 4, press the [2+] button on the remote To release from this mode, touch the [1] touch key on the main
commander. Each time the [2+] button is pressed, the display unit or press the [1] button on the remote commander. The mes-
changes from model name → destination → MTK version → sage “RESET” appears on the screen display panel.
BT version → SW version (not available for HT-RT3 model)
in this order, and returns to the model name display. For software version other than 1.031:
6. In the state of step 5, press the [2-] button on the remote com- Touch the [1] touch key on the main unit or press the [1] button
mander and all segments in screen display panel are lighted up on the remote commander to exit this mode. Touch again the [1]
and then is dimmed after a second. touch key on the main unit or press again the [1] button on the
remote commander and the message “RESET” appears on the
Releasing method: screen display panel.
To release from this mode, touch the [1] touch key on the main
unit or press the [1] button on the remote commander. DEMO MODE
The demo mode can be performed.
SOFTWARE VERSION CHECK (This mode is used by shop front)
The software version is displayed.
Procedure:
Procedure: 1. Touch the [1] touch key on the main unit to turn the power on.
1. Touch the [1] touch key on the main unit to turn the power on. 2. Touch the [INPUT] touch key and [VOL−] touch key on the
2. Press the [MENU] button on the remote commander and the main unit simultaneously for five seconds.
message “LVL >” is displayed on the screen display panel. Or press the button on the remote commander as following
3. Press the [m] button on the remote commander until the mes- order (each buttons press within 5 seconds).
sage “SYS >” appears. [BACK] → [ENTER] → [INPUT] → [%] → [INPUT] →
4. Press the [ENTER] button on the remote commander and the [%]
message “ASTBY” appears. 3. The message “DEMO1” is displayed on the screen display
5. Press the [m] button on the remote commander and the mes- panel, and enter the demo mode, then changed to the setting of
sage “VER” appears. initial value for demo mode.
6. Press the [ENTER] button on the remote commander and the
software version “X.XXX” appears. Releasing method:
Perform the “COLD RESET”.
AMP TEST Note: The demo mode does not release by unplug the AC cord.
Check the software version before execute this mode.
USB UPDATE TEST MODE
Procedure: To update micontroller software through USB.
1. Touch the [1] touch key on the main unit to turn the power on.
2. Press button in order of the [u] → [DIMMER] → [2-] → Procedure:
[M] on the remote commander. 1. Plug in USB device in power on condition.
The messsage “MSURE” is displayed on the screen display 2. Touch the [1] touch key and [ ] touch key on the
panel. main unit simultaneously for five seconds.
3. In the state of step 2, press [DIMMER] button on the remote 3. The message “UPDT” appears and then “UD 0” appears on
commander. the screen display panel.
The message will appear in order of the “THRU”→ “F2S” → 4. If the updating progress succeeds, the message “UD100” ap-
“F2CW” → “FULL” on the screen display panel. pears and back to normal display.
5. If the updating progress fails, the message “U.ERR” appears.

14
 HT-RT3
SECTION 4
TROUBLESHOOTING
1. “PRTCT” is displayed on OLED display after turning the power on
Note: Please remove USB (removable device) before troubleshooting.

“PRTCT” is displayed on the OLED

display after turning the power ON.

Yes

UFOELK - 2/21/2018 5:23 PM

"PRTCT" is displayed after
removing Bar speaker (FRONT L,
FRONT R, CENTER speakers) Yes Check and replace the loudspeaker
and Surround speaker (SUR L, in subwoofer.
SUR R speakers) and turning the
power ON.

No

"PRTCT" is displayed after plugging

Bar speaker (FRONT L, FRONT R, Yes Check and replace the loudspeaker
CENTER speakers) and turning the in Bar speaker.
power ON.

No

"PRTCT" is displayed after plugging

Surround speaker (SUR L, SUR R Yes Check and replace the loudspeaker
speakers) and turning the power in Surround speaker.
ON.

No

Replace MAIN board IC1000 and Yes

IC1002 and check "PRTCT" is Replace complete MAIN board.
displayed.

2. The video of HDMI is not displayed during USB mode

Check MAIN board IC3200 No Check MAIN board IC3200 No Refer to "Power is not turned
pin 4 is 5V. pin 1 is 3.3V. on" on page 17.

Yes Yes

Replace complete MAIN Check MAIN board IC3200 No Replace MAIN board diode
board. pin 5 is 7.4V ~ 8V. (D3200).

Yes

Replace IC3200 on MAIN

board.

15
HT-RT3
Ver. 1.4

3. The sound is not outputted

Check the Subwoofer, Bar speaker

(FRONT L, FRONT R, CENTER
No Replace the speaker which is not
speakers) and Surround speaker
functionable.
(SUR L, SUR R speakers) are
functionable.

Yes

Check that the signal is inputted to

MAIN board IC1001:
No
pin 24 (FRONT L, FRONT R speakers) Replace complete MAIN board.
pin 25 (SUR L, SUR R speakers)
pin 27 (CENTER speaker, Subwoofer)

Yes

Check that the signal is outputted from

MAIN board IC1001:
pin 38, 39 (CENTER speaker)
pin 41 (FRONT L speaker) No
pin 43 (FRONT R speaker) Replace MAIN board IC1001.
pin 45 (SUR R speaker)
pin 47 (SUR L speaker)
pin 48, 49 (Subwoofer)

Yes

Check that the signal is outputted from

MAIN board IC1000: No
pin 27, 28, 32 (CENTER speaker) Replace MAIN board IC1000.
pin 35 (FRONT L speaker)
pin 39, 40 (FRONT R speaker)

Yes

Check that the signal is outputted from

MAIN board IC1002:
No
pin 27, 28, 32 (Subwoofer) Replace MAIN board IC1002.
pin 35 (SUR R speaker)
pin 39, 40 (SUR L speaker)

16
 HT-RT3
Ver. 1.4

4. Power is not turned on

Power is not turned on.

Yes

The voltage of the following is 20V/32V

No
SWITCHING REGULATOR: Replace the SWITCHING REGULATOR.
Connector (CN101) pin 2 to 4 and 8.

Yes

No
Check MAIN board IC3205 pin 1 is 12V. Replace IC3201 on MAIN board.

Yes

Check MAIN board connector (CN2006) No

Replace transistor (Q3208) on MAIN board.
pin 14 is 12V.

Yes

Replace complete MAIN board.

UFOELK - 2/21/2018 5:23 PM

17
HT-RT3
Ver. 1.3

5. USB cannot be detected

USB cannot be detected.

Yes

No No Refer to "Power is not turned

Check IC3000 pin 1 is 5.1V. Check IC3000 pin 4 is 3.3V.
on" on page 17.

Yes Yes

Check coil (L3000) pin 1 and No Check that there is no No Replace complete MAIN
abnormality on USB board Check IC3000 pin 5 is 5.1V.
pin 3 are shorted to ground. board.
connector (CN7000).

Yes Yes Yes

Replace complete MAIN Replace connector Replace IC3000 on MAIN

board. (CN7000) on USB board. board.

6. Display panel is not functioned

Yes Check voltage of C5008 on

No Display. OLED CHUKEI PC BOAR
board is around 12V.

No

Turn OFF the set and

Check resistance of C5008
disconnect the WIRE Yes
on OLED CHUKEI PC
(FLAT TYPE) from OLED
BOAR board is > MΩ.
CHUKEI PC BOAR board.
No

Replace C5008 on OLED

CHUKEI PC BOAR board. Yes Turn the power ON and
Replace Q3208 and L3207 confirm the Display function.
on MAIN board.

18
 HT-RT3
SECTION 5
DIAGRAMS
5-1. BLOCK DIAGRAM - MAIN CONTROL Section -
1)&02'8/( 6<67(0352&(6625
5&6:: ,&

 1)&BL$3B76B6&/
 1)&BL$3B6'$ ;7$/ 4
 1)&B,54
;
 1)&B5)'(7 0+]
;7$/  $5&%8))(5
,&
%/8(7227+02'8/( $5&B63',)
$5&B63',)B,1  1 < $ 
8$57B5;
 %7B5;'
%7B%227
 %7B%227 6(5,$/)/$6+ < 
087(
 %7B087( ,&
8$57B7;
 %7B7;' $ 
63',)B287
18 %7B63',)B,1 6)B'2   '2
%7B,17 ',
 %7B,17 6)B',  5
6)B&.   &/.
6)B&6  1 &6

6'5$0
,&
237,&$/
79,1
237,&$/ UFOELK - 2/21/2018 5:23 PM
5(&(,9(5
&1
237,1
 23763',),1 5'5' '4'4

5$5$ $$

$8',2$'& %$   %$

- ,&
%$   %$
/  9,1/ 5&/.   &/.
$1$/2*,1 '287  111 $'&B'2 5:(B   :(
5 14 9,15 &$6B   &$6
6&./  118 07.B,6B287B0&. 5$6B  18 5$6
'40  15 /'40
&1
/5&.   07.B,6B287B/5&. '40   8'40
$5& 14
'$7$ 1
%&. 8  07.B,6287B%&. 7;3 
'$7$ 
7;1 
'$7$ 4
 '$7$B&B6: 7;3 
'$7$ 
7;1 
'$7$ 
 07.B,6B287B&+B6/65 7;3 
'$7$ 
7;1 
&/2&. 
7;&3 88
&/2&. 
 '$7$B/B5 7;&1 
6&/ 15 +'0,287
+'0,B6&/ 
6'$ $5&ź
+'0,B6'$  
+273/8*'(7 
+3' 84
95(*
,&
32:(5
932:(5
$9''B  6833/< 816:9 806:9 5 9,1 9287 4 18
4 &217
1

&(&
&(&  

3&217B0$,1B6<67(0 

&1

86%B'3 11 '
86%B'0  '

‡6LJQDOSDWK
'$7$B/B5
$8',2',*,7$/
>001B
'$7$B6/B65 $8',2$1$/2*
'$7$B&B6: AUDIO SECTION
9,'(2 
07.B,6B287B%&. (Page 20)
07.B,6B287B/5&.   86%
07.B,6B287B0&.
  %/8(7227+

HT-RT3
19 19
HT-RT3
Ver. 1.2

5-2. BLOCK DIAGRAM - AUDIO Section -

STREAM PROCESSOR DIGITAL POWER AMP
IC1001 IC1002
L1001
+
SUR L
>001B DATA L R
24 SDIN1 PWM P 7 47 5 INPUT A OUT A 39
SL -
–
DATA SL SR ONLY FOR SS-SRT3
MAIN CONTROL SECTION 25 SDIN2 OUT A 40
DATA C SW SR + SPEAKERS
(Page 19) MTK I2S OUT MCK
27 SDIN4 PWM P 4 45 6 INPUT B OUT B 35 +
11 MCLK SUR R
MTK I2S OUT LRCK
MTK I2S OUT BCK
22 LRCK –
23 SCLK
L1002 CN1001

PWM P 8 49 14 INPUT C OUT C 32 SW+ 3

OUT D 27
SW+
4 -

+
SW- LOUDSPEAKER
PWM M 8 48 15 INPUT D OUT D 28 1

RESET

-
SW- 2

TB6000

DIGITAL POWER AMP

IC1000
L1003
FR +
PWM P 3 43 5 INPUT A OUT A 39 +
OUT A 40 FRONT R
–
FL +
PWM P 2 41 6 INPUT B OUT B 35 + FRONT L
ONLY FOR SS-RT3
– SPEAKERS
L1004
CTR +
PWM M 1 38 14 INPUT C OUT C 32 +
OUT D 27 CENTER TB6001
CTR -
PWM P 1 39 15 INPUT D OUT D 28 –

RESET
4

VALID 37
RESET
MUTE
PDN
SDA
SCL

BUS BUFFER
Q2001 IC2007 20 21 19 18 16

7 G2

5 A2 Y2 3 X2001
27MHz

101 40 31 113 104 112 4 3

TAS SDA

TAS XRST
OLED CS

OLED TAS CLK

TAS XMUTE
TAS XPND

XTAL0

XTAL1
‡6LJQDOSDWK
SYSTEM PROCESSOR
IC2003 (MAIN board Suffix-12) : AUDIO (DIGITAL)
IC2009 (MAIN board Suffix-13) : AUDIO (ANALOG)

HT-RT3
20 20
 HT-RT3
Ver. 1.2

5-3. BLOCK DIAGRAM - POWER SUPPLY Section -

SYSTEM PROCESSOR
IC2003 (MAIN board Suffix-12)
RESET UNSW3.3V
REMOTE CONTROL IC2009 (MAIN board Suffix-13)
RECEIVER IC2001
IC5001
SWITCHING
MTK RESET 28 4 OUT VDD 2 + 3.3V
Q2003,Q2004
OUT 2 29 SIRCS

+3.3V REG.
BT 3.3V
Q3209,Q3210

NFC MODULE
(RC-S730 (WW)) PCONT BT 34

CLK
DATA +3.3V REG.
D 3.3V
IRQ Q3203,Q3204
33 NFC IRQ
RFDET
38 NFC RFDET

+1.2V REG.
MFI IC3204
IC2006

SCL 6 CORE1.2V 1 VO VCC 6

EN
SDA 2 4

+5.1V/ +3.3V REG.

IC3205
VOLTAGE DETECTOR USB VSUS UNSW3.3V
IC4002 IC3000 3 SW1
VIN1 1
SW5.1V
UNSW3.3V 2 VDD OUT 4 VSUS 1 OUT IN 5 14 SW2 VIN2 16
EN1 5
AMP PROTECT 102 3 FLT EN/EN 4 12 EN2

CAP SENSE CONTROLLER

D5000
(BT LED) IC4001 DIGITAL POWER AMP
IC1000 +12V REG.
11 CS7/GPO3/SH GVDD 12V
Q3212,Q3213
16 FALUT

JL4004
VOL+ 1 CS0/PS0 I2C SCL 15 100 NFC iAP TS SCL 17 OTW

JL4003
VOL- 2 CS1/PS1 I2C SDA 14 99 NFC iAP SDA
DIGITAL POWER AMP +12V REG.
JL4002 IC1002 OLED 12V
Q3207,Q3208
PAIRING
JL4001
UFOELK - 2/21/2018 5:23 PM
8 CS4/GPO0 HI/BUZ 16 32 TS INT
16 FALUT
INPUT 9 CS5/GPO1
17 OTW +5V REG.
JL4005
10 CS6/GPO2 IC3207
1
A 5V 3 VOUT VDD 4
CE
1
CN5002
4 83 OLED DC
6 98 OLED RESET +5V REG.
3 41 OLED DOUT IC3200
OLED
5 101 OLED CS
STREAM PROCESSOR 4 VOUT VIN 5
HDMI 5V
BUS BUFFER IC1001
IC2007 CONT
1
G1 1
EMO1

OLED CLK
2 6 Y1 A1 2 40 OLED TAS CLK 15
+7V REG.
DC FAN
IC3202
FAN 7V
4 VO DC/DC
UNSW12V
FAN MOTOR VDD 8 CONVERTER
FAN CTRL 116 DRIVE 2 FB IC3201
Q3211 EN
5 REGULATOR, SWITCHING
3L405W-2 (EXCEPT E12) /
AC CUT REGULAR, SWITCHING
IC2008 3L405W-3 (E12)

SUB 32V
AC CUT 115 4 OUT VDD 2
(AC IN)

PVDD 32V

PCONT MAIN SYSTEM 39 PCONT MAIN SYSTEM

HT-RT3
21 21
 HT-RT3
Ver. 1.1

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards. For Schematic Diagrams. BLUETOOTH module
Note: Note: SPEAKER CHUKEI PC BOAR board
• X : Parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF)
• Y : Parts extracted from the conductor side. 50 V or less are not indicated except for electrolytics and
• f : Internal component. tantalums. REGULATOR, SWITCHING 3L405W-2 (Except E12) /
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise REGULATOR, SWITCHING 3L405W-3 (E12)
(The other layers’ patterns are not indicated.) specified.
RC-S730 (WW)
• f : Internal component.
Caution: • 2 : Nonflammable resistor.
Pattern face side: Parts on the pattern face side seen • 5 : Fusible resistor.
(Conductor Side) from the pattern face are indicated. • C : Panel designation.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated. Note: The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
• MAIN board is multi-layer printed board. However, the Replace only with part number specified. TOUCH board
patterns of intermediate layers have not been included in MAIN board
diagrams. Note: Les composants identifiés par une marque
0 sont critiques pour la sécurité. OLED CHUKEI PC BOAR board
• Indication of transistor.
Ne les remplacer que par une piéce portant
le numéro spécifié. CONNECTOR board
C
• A : B+ Line. USB board
Q These are omitted.
• Voltages and waveforms are dc with respect to ground
B E
under no-signal conditions.
no mark : POWER ON
• Abbreviation • Voltages are taken with VOM (Input impedance 10 M).
AR : Argentina model Voltage variations may be noted due to normal production
AUS : Australian model tolerances.
CND : Canadian model • Waveforms are taken with a oscilloscope.
E12 : 220-240 V AC area in E model Voltage variations may be noted due to normal production
EA : Saudi Arabia model tolerances.
LA9 : Latin-American model • Circled numbers refer to waveforms.
SP : Singapore model • Signal path.
F : AUDIO (DIGITAL)
Note 1: When the complete MAIN board is replaced, J : AUDIO (ANALOG)
refer to “NOTE OF REPLACING THE IC1000 E : VIDEO
AND IC1002 ON THE MAIN BOARD AND L : USB
THE COMPLETE MAIN BOARD” on page 5. a : Bluetooth

Note 2: When the complete MAIN board is replaced,

spread the bond referring to“BOND FIXATION • Abbreviation
OF ELECTRIC PARTS” on page 6. AR : Argentina model
AUS : Australian model
CND : Canadian model
E12 : 220-240 V AC area in E model
EA : Saudi Arabia model
LA9 : Latin-American model
SP : Singapore model

HT-RT3
22 22
 HT-RT3
Ver. 1.2

5-4. PRINTED WIRING BOARD - MAIN Board - • See page 22 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

MAIN BOARD
A (COMPONENT SIDE)
REGULATOR, SWITCHING
3L405W-2 (EXCEPT E12) /
REGULAR, SWITCHING ~ AC IN
3L405W-3 (E12)
DC FAN (CHASSIS)

J3400
3 CN3200 4 ANALOG IN
C1099 R3271
C3271 1 2
B

L1000

R3284
R3413
C1044 D3205
CN1000

C3254
1 10
C3203

C3255
JL1001 IC3202

R3247
Q3211

R3207
(CHASSIS) R3202 C3256

R3288
8
JL1000

1
C3222

L3206
R1015
R3205 9

C1050 C1001
5 4 R3215

R1016

R1012
JL1003
Q3204

R3286
R3204 1
IC3201 4 5 Q3203

C1019

C3274
R3203 R3228
C1027
9

R2065 R3248

C3277
C3212
R3234 TV IN

CN3400
C1012

R3277
C1085

FB3400
5 JL1024 8 1 C3220 2

R1004
R1033
OPTICAL

R1013

R3226
R1014

JC1001
R1032

JC1002
1

C1045 C1046
JL1023 C1020 JL1025
C1018

R2072
R1010
3

R2070
R2061
C1051

C1023
R1009
C1014
CN1001

L3202
-

L3200
LOUDSPEAKER JL1022

R2073
C1048 C1064 R3229 C3230
C1017
-

FB2001

C3400
+

R2068

R2055
R1011

C3242
C3240

R2121
R2080
R2120
JL1009

C1008

R2118
C1063 R2071

Q2005
JL1013
4 R3214 R3287

C3272
JL1014
C 6 28 1

JL1021

R2119
1
C1047

C2085
L1002 L3204

R2215
C3266
C3239
JL1010

R1005
L1003 C3201 R2212 R2069

JL2161
R1031
C1056 R1029 IC1001 R1024 C1004 C2075
C3200

JL2160
C1065

R2074

R2214
R2213
C1028

C1024
C1029 JL1035 29 C1049 C2066 C2074

C2029
C3238
JL1020

56 1 16 R2067
C1041 C1042

C3243
C2065

JL3201
C1058
C1057

JL2162
C1084

23 22 1 44 C1005 21
R1000 17 L3205 X2001 20
JL1036 JL1026
C1043

R2024
C3248
C3249
C1055

JL1012

JL3200
C3235 L3203 IC3205 128
JL1034 97 1

L3001
JL1027

JL1019
1

C1021
C3234 8 9 96

CN1002
R3244

C1053
C1036

C1013

L3002
R3232

R1039
R1030
R1003
R1038
R1037
R1019

R1036
Q2003

C2030

R2146
R2026
IC1000
IC1002
JL1015

R1001
JL1033

R1002
JL1007 R3233 C3241 Q2004

JL1006

CN3001
JL1011
JL1016 JL1008 HDMI OUT

C1061
6 129

C1037

R3231
JL1028 R3015 $RC ź

RB2007
1 R3017
IC2003 (Suffix-12)

C3273
R2153 JL2039

C2117
C1060
R3016
CN3000

IC2009 (Suffix-13)

R2219
C1033 IC2008 R2016
JL1031

RB2009
R3018

JC1003
C1003 3 2 19

Q2000
C1025
JC1000
C1062 R1026 JL2041

JL1004
C1000
R1028
R2205 R2208

JL1029
44 1 22 23 R2218 4 1 JL2042 23

JL1017
5
D

R1006
C3015 22

R2022
C1040

R2145
7
C1032 C1059 C1039 R2222 32
C1066 64 65

JL1005

R2036
JL2040 33
>001P

R2220
C2116
C1002 L1004

C1009
CL1000

R3023
C3006 R1040 R1025 D2000
L1001 2 1 R3022

R2017

R3020
RB2004 RB2006

JL1018
C1067 R2021 R2066

C1026
USB BOARD R2058

R2148
C1030 C1031

C1007 C1006
C2028 6

R3021
CN7001 3 4 4 1

R3019
13

C2027
IC2001

R2088
(Page 27) 4

RB2003
RB2002
IC3001

R1007
R1027

R2161 FOR

CN2009
C2025
JL3004

RB2005

C3012
5 8

R2210
R2217 R2023 R2062 SERVICE USE
RB2008

C3013
L3000 1
C2084

C2083
C2086

JL1032 4 1
JL1030 R2211
RB2001

54 28 9 5

C2023
IC2006 5 8

R2216
R2114
20

R2060
19
C2104

R2160
R2140

C2105
JL2152 IC2005
E JL2154

R2117
R2116
C2103
R2141
JL2148
C2124

C2099 JL1002 1 17

C2091
R2149

12, 13
C2101

C2088 CN2002
CN2006

2 18
C2102

JL2158 1 27
R2150

(12, 13)
1
R2201
(CHASSIS) 1-980-405-
BLUETOOTH MODULE
(CHASSIS)
20 1
19

F
CN2006

CN1002
2
1
>002P
CONNECTOR BOARD

MAIN BOARD
UFOELK - 2/21/2018 5:23 PM CN5008
(Page 27)

>003P
SPEAKER CHUKEI
G (CONDUCTOR SIDE) PC BOAR BOARD
CN6000
(Page 26) 13
C3403
R3407
R3402
R3404

C3405 Q3208 Q3213

FB3201
C3270

C3269

R3291
CL3401 3 2 CL1037

C3278

L3208
R3290
IC3207 R3250 R3272
C3268 C1098 CL1004

R3251
4 1
CL3402 R3289
C3406
R3408

R3252
R3403
R3405
C3412 C3404

C3264
C3410 CL1011 CL1010 CL1003
D3206
CL3002 L3207
H CL3001 C1097
Q3207 Q3212
C3409
C3411

1 14 R3295 CL1009
CL1001
C3415
C3414
IC3401 CL1008
7 8 CL3400 CL1013
C3413
CL3403 CL1006
CL1014
R3406

CL1020
R3417 R2157 R1008 CL1007
R2063

R2079
R3418 C2100 C1016

R1018
R3257
C2021
R2143

CL1012
C1022 C1015
CL1015 C1054

C1052
L2002 C3227
I
C2076
C2077

R2142
R2081

C2002 C2008
C2006 C2004
C2033 C2063
C2064

R2144 CL1016
6 5 4 C3228 CL1017

C1035
C1011
C2067
L2003

C2068

R1017
C2073

7 IC3204
C2019

R3242
R2085

C2031

R3006 C2072
C2069

L2000

C2062 123 CL2140

C2070 CL3000
R3012

R2083 C2061 C3231 CL1005

R2082 C2056
R3013

C2055 C2060 R2033

R2084

R3236

C2054 C2059 C3233 CL2144

C1010
C2022

CL1018

C1034
C3010 R3014 C2053 C2058 R2034 CL2145
CL2141
C2049

C1038
C2050

R3010 C2052 C2057 R3235

C2005
C2009

C3009 R3011 C2051 R2035 CL2143 R2004

C2118

R2040 R2041 CL1021

C2046

C2048 R2126 C2107

C2045

R2000 C2097
R2001

C2047 R2043 CL2146

C2024
R2014

R2054 R2127 R2002

R2028

C2003
R2193 D2001

L2001

R2064
C2121
R2039

J
C2098
C2010

C2007 R2042 1 8 R2015

C3208
C3210
C3211

R2049
R2048

IC3200
C3214

C2020

CL1019
CL2100 IC2000 CL2142
CL1002 CL1023
5 4 4 5 Q2001
D3200

1 2 3
CL2101 CL3003
Q3209
CL2102 R3296 C2109 R2170
C3204
R3206

R3254 R2172
R3269

Q3210
CL1022
C2108
C2042
C2043

R2094 CL2104 CL2106

R3279
R3278

L2004
8 5
R2129

1 4

R2171 R3004
C2095
C2094
C2093
C2092
C2096

R2138
CL2121

R2139
IC2007 CL2132 CL2107
R2128

R2168
R3280

R2169 CL2134 CL2131 C3005

C3275
C3276

R2164
R2194 R2173

R2167 CL2105
C2037

CL2130
C2038

3 2 1 CL2111 CL2108
CL2137 CL2115
CL2127 IC3000 CL2103
C2041

C2040
R2092

CL2129
C2039

12, 13
CL2125 CL2117
R2165

CL2139 CL2110
K
R2209

C3002
CL2135 CL2133 4 CL2118 R2221
R2199 5
CL2128 CL2123 C3000 CL2119
CL2124 CL2138 CL2120 CL2109
R2202
(12, 13)

R3001
CL2122 CL2136 CL2114
CL2126 1-980-405-

Note 1: When the complete MAIN board is replaced, refer to “NOTE OF REPLACING THE IC1000 Note 2: When the complete MAIN board is replaced, spread the bond referring to“BOND FIXATION
AND IC1002 ON THE MAIN BOARD AND THE COMPLETE MAIN BOARD” on page 5. OF ELECTRIC PARTS” on page 6.

HT-RT3
23 23
 HT-RT3

5-5. PRINTED WIRING BOARD - OLED CHUKEI PC BOAR Board - 5-6. SCHEMATIC DIAGRAM - OLED CHUKEI PC BOAR Board -
• See page 22 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10

OLED CHUKEI PC BOAR BOARD

A (COMPONENT SIDE) A
OLED CHUKEI PC BOAR BOARD C 5010
R 5008
22
1
C L5025
C 5014 D 5000
1 CL-194S-HB8SP-SD-T
C N 5003

C5014
R5001 C5010
6P

C5020
R5009

C5018
C5000
R5008 1 UNSW3.3V
C5008

R5005
4 3
7 1 R5004 2 T S _C LK
B 1
IC5001
2
R5000
C5001 R5003
D5000 CN5005

6
8
B 3 TS_INT
6
>001S

C5015
8

R5006
C5011 C5007
R5002
CN5003 R5007 1
4 TS_DATA
2 10 CN5004 7 TOUCH BOARD
1 11 5 B T _LE D CN4001
1 20 (Page 25)
12 13 6 GND
CN5002 21 22

C N 5005
6P
UNSW3.3V 1
>004P ELEMENT, ORGANIC
>005P NFC MODULE
C NFC_CLK 2 C N 5004
C TOUCH BOARD
EL INDICATOR
CONNECTOR BOARD
(RC-S730 (WW))
NFC MODULE NFC_GND 3
20P
CN4001 CN5009 (RC-S730 (WW)) 20 U N S W 3 . 3 V
(Page 25) (Page 27) NFC_DATA 4
19 N F C _ C L K
NFC_IRQ 5
18 G N D
11 NFC_RFDET 6
C 5015 C 5018
17 N F C _ D A T A
100P 100P 16 N F C _ I R Q

1-980-596- (11) 15 N F C _ R F D E T
14 V C C 1 2 V

OLED CHUKEI PC BOAR BOARD

R 5006 0
D D 13 O LE D _R S T
12 O LE D _C S B
(CONDUCTOR SIDE) 11 O LE D _D C
>002S
10 O LE D _D O U T
CONNECTOR
9 UNSW3.3V BOARD
CN5009
8 O LE D _C LK

1K
(Page 27)

0
0
0
0
7 GND
R 5001
47 I C 5001 6 TS_INT

R5009
R5005
R5004
R5003
R5002
E E R S -470 5 GND
CL5025
I C5001 4 T S _C LK
RECEIVER
3 GND
3
4 VCC GND2 1 R 5000 2 TS_DATA
3 47
3 GND1 OUT 2 1 SIRCS
C 5000
1
C 5020
220P

F F
11
1-980-596- (11) C N 5002 C 5007 C 5011
11P 0. 1 0. 1
O -LE D _G N D 11
V C C 12V 10
V C C 12V 9 R 5007
39K C 5008 10 C 5001 0. 1
O -LE D _I R E F 8
G UNSW3.3V 7
ELEMENT,
ORGANIC O -LE D _R E S E T 6
EL INDICATOR
O -LE D _C S B 5
O -LE D _D C 4
O -LE D _D O U T 3
O -LE D _C LK 2
O -LE D _I X S 1

HT-RT3
24 24
 HT-RT3

5-7. PRINTED WIRING BOARD - TOUCH Board - • See page 22 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

TOUCH BOARD TOUCH BOARD

A (COMPONENT SIDE) (CONDUCTOR SIDE)

UFOELK - 2/21/2018 5:23 PM

R4001 JL4005
1

R4009
R4008
R4003 JL4003
IC4002 R4002 IC4001
B C4005 3 2 R4010
JL4001
INPUT
JL4002
PAIRING
VOL- JL4004
VOL+

C4003
C4004 12
13 9 8
C4002
4 1
16 17 5
1 4
7 C4001
1
CN4001

>004P C4000
R4014
R4007

6 R4005
R4013
8 R4000
OLED CHUKEI PC
BOAR BOARD
CN5003
(Page 24)

C
11 11
(11) 1-980-707- (11)
1-980-707-

5-8. SCHEMATIC DIAGRAM - TOUCH Board - • See page 29 for IC Block Diagrams. • See page 29 for IC Pin Function Descriptions.
1 2 3 4 5 6 7 8 9 10 11 12 13

TOUCH BOARD

C4000 R4005 R4007 IC4002

0.0022 560 560 PST8429UL
R4014
5.6K IC4002
VOLTAGE DETECTOR
C4007
10P 3.1
C4001 1 GND OUT 4
C 0.1
1.9 0.3 0 0
3.4
2 VDD CD 3
0.3

4 3 2 1 C4004 C4005
0.0047 0.0047
VCC
CMOD
CS1/PS1
CS0/PS0

CN4001
6P
R4013
22 R4015 6 UNSW3.3V
3.4 3.4 0 R4000 22
5 VDDIO IC4001 HI/BUZ 16 5 TS_CLK
3.4 CY8CMBR3108 3.4 R4001 22
6 VDD I2C_SCL 15 4 TS_INT
IC4001 3.4 R4002 22 >001S
D C4003
0.1
C4002
1 0
7 VSS
CAP SENSE CONTROLLER
I2C_SDA 14
R4003 0
3 TS_DATA
OLED CHUKEI
8 CS4/GPO0 CS3 13 2 BT_LED PC BOAR BOARD
CN5003
CS7/GPO3/SH

1 GND (Page 24)

CS2/GUARD
CS5/GPO1
CS6/GPO2

9 10 11 12
0 0 1.3 0
R4010 R4011
560 0
E
R4008 R4009
560 560

F JL4004 JL4003 JL4002 JL4001

JL4005
VOL+ VOL- PAIRING INPUT 1

HT-RT3
25 25
 HT-RT3

5-9. PRINTED WIRING BOARD - SPEAKER CHUKEI PC BOAR Board - 5-10. SCHEMATIC DIAGRAM - SPEAKER CHUKEI PC BOAR Board -
• See page 22 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10
JL6000

SPEAKER CHUKEI PC BOAR BOARD

A (COMPONENT SIDE) A

SPEAKERS

ONLY FOR
SS-SRT3
ONLY FOR
SS-RT3
SPEAKER CHUKEI PC BOAR BOARD
C L6001
SUR L SUR R FRONT L FRONT R CENTER
C 6023 C 6022 C 6024
0. 001 0.01 0.047
B B T B 6001
IN IN IN IN IN
+
OUT OUT OUT OUT OUT C 6025 C 6020 C 6021
- CENTER ONLY FOR SS-RT3
0.047 0.001 0.01
C L6000

C 6003 C 6002 C 6026

0. 001 0.01 0.047

C C R 6001
100K
TB6000 C N 6000 C 6027 C 6000 C 6001
13P 0.047 0.001 0.01
C 6014
S L + 13 1000
S L - 12
TB6001 SPEAKERS
S R + 11
C6003 C6000 C6018 C6015 C6007 C6006 C6023 C6020 C 6019
C6011 C6010
C6002 C6001 C6017 C6016 C6012 C6009
C6008 C6005 C6022 C6021 S R - 10 1000
C6026 C6027 C6028 C6029 C6030 C6031 C6032 C6033 C6024 C6025
F L+ 9
R6001 R6004
R6002 R6003 F L- 8 C 6018 C 6017 C 6028
D D MAIN BOARD FR+ 7
0.001 0.01 0.047 R 6002
100K
CN1002 T B 6000
FR- 6
C 6029 C 6015 C 6016
C6014

C6019

C6013

C6004

+
CTR + 5 0.047 0.001 0. 01 -
B LU SUR L
ONLY FOR SS-SRT3
JL6000 CTR + 4 + GRY SUR R
-
CTR - 3
+ WHT
- FRONT L
CN6000
C 6011
0.001
C 6012
0.01
C 6030
0.047 R 6003 ONLY FOR SS-RT3
13 1 CTR - 1 + RED FRONT R
100K -

E (CHASSIS) E C 6031 C 6010 C 6009

C 6013
1000 0.047 0.001 0.01

C 6004
>003P 11 1000

MAIN BOARD
CN1002
(Page 23) 1-980-597- (11) C 6007
0. 001
C 6008
0.01
C 6032
0.047
R 6004
100K
F F C 6033 C 6006 C 6005
0.047 0.001 0.01

SPEAKER CHUKEI PC BOAR BOARD

(CONDUCTOR SIDE)

G G

I 11
1-980-597- (11)

HT-RT3
26 26
 HT-RT3

5-11. PRINTED WIRING BOARD - CONNECTOR Board - 5-13. PRINTED WIRING BOARD - USB Board -
• See page 22 for Circuit Boards Location. • : Uses unleaded solder. • See page 22 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 1 2 3 4

CONNECTOR BOARD USB BOARD

A (COMPONENT SIDE) A (COMPONENT SIDE)

>005P
OLED CHUKEI PC
>001P
BOAR BOARD MAIN BOARD
20 2 CN5004
CN5009 6 1 CN3000
19 1 (Page 24) (Page 23)
B B CN7001

4 1

C7001
CN7000
7 6 5 C7002

C7000
R5111
R5112

R5108

C7003
C7004
R5109

1 CN5008 20

21 22
C C
11
>002P
11 1-980-598- (11)
MAIN BOARD
CN2006
(Page 23)
1-980-901- (11)
UFOELK - 2/21/2018 5:23 PM USB BOARD
D D (CONDUCTOR SIDE)
CONNECTOR BOARD
(CONDUCTOR SIDE)

E E

(CHASSIS)
11
F 11 F 1-980-598- (11)
1-980-901- (11)

5-12. SCHEMATIC DIAGRAM - CONNECTOR Board -

1 2 3 4 5

CONNECTOR BOARD
A
CN5009 CN5008
20P 20P
U N S W 3 . 3 V 20 20 U N S W 3 . 3 V
N F C _ C L K 19 19 N F C _ C L K
GN D 18 18 G ND
N F C _ D A T A 17 17 N F C _ D A T A
N F C _ I R Q 16 16 N F C _ I R Q

B N F C _ R F D E T 15 15 N F C _ R F D E T
VC C 1 2 V 14 14 VCC12V
OL ED _ R ST 13 13 O LED_RST
OL ED _ C SB 12 12 O LED_CSB
OL ED _ D C 11 11 O LED_DC MAIN BOARD
>002S R5108 0
OL ED _ D OU T 10 10 O LED_DO UT CN2006
OLED CHUKEI
PC BOAR BOARD UNSW3.3V 9 9 UNSW3.3V
CN5004 R5109 0
(Page 24) OL ED _ C L K 8 8 O LED_CLK

C TS_INT 6
GN D 7 7 G ND
6 TS_INT
GN D 5 5 G ND
R5111 0
TS_ C L K 4 4 TS_CLK
GN D 3 3 G ND
R5112 0
TS_DATA 2 2 TS_DATA
SIRCS 1 1 SIRCS

HT-RT3
27 27
HT-RT3

MEMO

HT-RT3
28 28
 HT-RT3
Ver. 1.1

• IC Block Diagrams
IC4002 PST8429UL (TOUCH BOARD)

GND 1

VREF

+
–

4 OUT

VDD 2 3 CD

• IC Pin Function Descriptions

TOUCH BOARD IC4001 CY8CMBR3108-LQXIT (TOUCH KEY CONTROLLER)
Pin No. Pin Name I/O Description
1, 2 CS0/PS0, CS1/PS1 - Fixed at “L” in this unit
3 CMOD - External capacitor connection terminal
4 VCC O Internal regulator output terminal
5 VDDIO - Power supply terminal (+3.3V)
6 VDD - Power supply terminal (+3.3V)
7 VSS - Ground terminal
8 CS4/GPO0 I/O Touch key input/output terminal Not used
9 CS5/GPO1 I VOL + touch key input terminal
10 CS6/GPO2 I VOL – touch key input terminal
11 CS7/GPO3/SH I PAIRING touch key input terminal
12 CS2/GUARD I INPUT touch key input terminal
13 CS3 I Power touch key input terminal
14 I2C_SDA I/O Two-way I2C serial data bus with system controller
15 I2C_SCL I/O Two-way I2C serial data transfer clock signal bus with system controller
16 HI/BUZ O Interrupt signal output to the system controller

UFOELK - 2/21/2018 5:23 PM

29
HT-RT3
Ver. 1.3
SECTION 6
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • Abbreviation
The components identified by mark 9 con-
they may have some difference from the AR : Argentina model
tain confidential information.
original one. AUS : Australian model
Strictly follow the instructions whenever the
• Items marked “*” are not stocked since CND : Canadian model
components are repaired and/or replaced.
they are seldom required for routine ser- E12 : 220-240 V AC area in E model
vice. Some delay should be anticipated EA : Saudi Arabia model Les composants identifiés par la marque
when ordering these items. LA9 : Latin-American model 9 contiennent des informations confidenti-
SP : Singapore model elles.
• The mechanical parts with no reference The components identified by mark 0 Suivre scrupuleusement les instructions
number in the exploded views are not sup- or dotted line with mark 0 are critical for chaque fois qu’un composant est remplacé
plied. safety. et / ou réparé.
• Color Indication of Appearance Parts Ex- Replace only with part number specified.
ample:
KNOB, BALANCE (WHITE) . . . (RED) Les composants identifiés par une marque
  0 sont critiques pour la sécurité.
Parts Color Cabinet’s Color Ne les remplacer que par une pièce portant
le numéro spécifié.
6-1. OVERALL SECTION

8
TOUCH board (ns)

#1 5 chassis section
4
3
4
ns
OLED CHUKEI PC
BOAR board (ns)
7
ns A A
6

#1
ns

ns

ns 1 10
ns

11
ns

Note 2: When the RC-S730 (WW) is replaced, refer Note 1: If wire (flat type) is replaced, install it after bend-
“NOTE OF REPLACING BLUETOOTH MOD- ing it in the same form as that before replace-
ULE OR RC-S730 (WW)” on page 5. ment.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-2592-789-1 PANEL, FRONT (EL-SW) ASSY 8 4-586-705-11 DOUBLE ADHESIVE TAPE
2 A-2089-365-A USB BOARD, COMPLETE 9 4-238-407-12 SCREW (1) (4X20), +BV TAPPING
3 8-989-602-00 RC-S730 (WW) 10 1-859-169-21 LOUDSPEAKER 16CM
4 1-828-156-51 WIRE (FLAT TYPE) (6 CORE)
5 4-459-006-01 DOUBLE ADHESIVE TAPE (NFC) 11 2-682-469-11 FOOT (SW)
#1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
6 1-828-230-51 WIRE (FLAT TYPE) (20 CORE) ns not supplied
7 1-812-049-11 ELEMENT, ORGANIC EL INDICATOR

30
 HT-RT3
Ver. 1.3

6-2. CHASSIS SECTION

55 #1
#1

ns

54

ns
#1 ns

53
ns
#2

MAIN board section

UFOELK - 2/21/2018 5:23 PM

52
ns
53 #2

51

Note 1: If wire (flat type) is replaced, install it after bend-

ing it in the same form as that before replace-
ment.

Note 2: When the BLUETOOTH MODULE is replaced,

refer “NOTE OF REPLACING BLUETOOTH
MODULE OR RC-S730 (WW)” on page 5.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 4-874-614-32 +BV TAPPING SCREW TYPE-1 3.5 #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
52 4-582-968-01 PANEL, REAR (EL-SW) #2 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
53 4-587-548-01 CATCHER, RUBBER (EL-SW) ns not supplied
54 1-828-218-51 WIRE (FLAT TYPE) (18 CORE)
55 1-493-097-11 BLUETOOTH MODULE

31
HT-RT3
Ver. 1.1

6-3. MAIN BOARD SECTION

#1
#1

A
104
B
ns

SPEAKER CHUKEI PC
BOAR board (ns) CONNECTOR board (ns) #1

#1 101

C
103 E
107
D
102

ns

ns

E
B
A D

ns

101 #3

101
101 101 ns

105 Note 1: When the complete MAIN board is replaced, re-

fer to “NOTE OF REPLACING THE IC1000 AND
IC1002 ON THE MAIN BOARD AND THE COM-
106 PLETE MAIN BOARD” on page 5.

Note 2: When the REGULATOR, SWITCHING 3L405W

board is replaced, spread the bond referring to
“BOND FIXATION OF ELECTRIC PARTS” on
page 6.
Note 4: When the complete MAIN board is replaced,
spread the bond referring to“BOND FIXATION OF Note 3: If wire (flat type) is replaced, install it after bending
ELECTRIC PARTS” on page 6. it in the same form as that before replacement.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 3-077-331-41 +BV3 (3-CR) 0 105 4-966-267-12 BUSHING (FBS001), CORD
0 102 1-855-244-11 DC FAN 0 106 1-834-966-42 POWER-SUPPLY CORD (AEP, SP, LA9)
9 103 A-2107-088-A MAIN BOARD, COMPLETE (for SERVICE) 0 106 1-835-068-21 CORD, POWER (AUS)
(US, CND)
9 103 A-2107-150-A MAIN BOARD, COMPLETE (for SERVICE) (AEP) 0 106 1-837-308-12 CORD, POWER-SUPPLY (US, CND)
9 103 A-2107-159-A MAIN BOARD, COMPLETE (for SERVICE) (UK) 0 106 1-837-312-11 CORD, POWER-SUPPLY (AR)
0 106 1-839-999-22 POWER-SUPPLY CORD (UK, EA)
9 103 A-2107-210-A MAIN BOARD, COMPLETE (for SERVICE) (E12) 0 106 1-848-053-12 POWER-SUPPLY CORD (E12)
9 103 A-2107-762-A MAIN BOARD, COMPLETE (for SERVICE) (AUS) 0 107 1-474-638-11 REGULATOR, SWITCHING 3L405W-2
9 103 A-2107-776-A MAIN BOARD, COMPLETE (for SERVICE) (SP) (EXCEPT E12)
9 103 A-2107-842-A MAIN BOARD, COMPLETE (for SERVICE) (LA9)
9 103 A-2107-983-A MAIN BOARD, COMPLETE (for SERVICE) (AR) 0 107 1-474-638-21 REGULATOR, SWITCHING 3L405W-3 (E12)
#1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
9 103 A-2119-853-A MAIN BOARD, COMPLETE (for SERVICE) (EA) #3 7-682-546-09 SCREW +B 3X5
104 1-828-228-51 WIRE (FLAT TYPE) (20 CORE) ns not supplied
32
 HT-RT3
SECTION 7 Ver. 1.5
ELECTRICAL PARTS LIST CONNECTOR MAIN
OLED CHUKEI PC BOAR SPEAKER CHUKEI PC BOAR
Note:
• Due to standardization, replacements in • CAPACITORS When indicating parts by reference num-
the parts list may be different from the uF: μF ber, please include the board name.
parts specified in the diagrams or the com- • COILS
ponents used on the set. uH: μH The components identified by mark 0
• -XX and -X mean standardized parts, so • SEMICONDUCTORS or dotted line with mark 0 are critical for
they may have some difference from the In each case, u: μ, for example: safety.
original one. uA. . : μA. . , uPA. . , μPA. . , Replace only with part number specified.
• Items marked “*” are not stocked since uPB. . : μPB. . , uPC. . , μPC. . ,
they are seldom required for routine ser- uPD. . : μPD. . Les composants identifiés par une marque
vice. Some delay should be anticipated • Abbreviation 0 sont critiques pour la sécurité.
when ordering these items. AR : Argentina model Ne les remplacer que par une pièce portant
• RESISTORS AUS : Australian model le numéro spécifié.
All resistors are in ohms. CND : Canadian model
METAL: Metal-film resistor. E12 : 220-240 V AC area in E model The components identified by mark 9 con-
METAL OXIDE: Metal oxide-film resistor. EA : Saudi Arabia model tain confidential information.
F: nonflammable LA9 : Latin-American model Strictly follow the instructions whenever the
SP : Singapore model components are repaired and/or replaced.
Les composants identifiés par la marque
9 contiennent des informations confidenti-
elles.
Suivre scrupuleusement les instructions
chaque fois qu’un composant est remplacé
et / ou réparé.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

CONNECTOR BOARD IC3204 6-720-509-01 IC BD00IC0WHFV-GTR

*****************
< COIL >
UFOELK - 2/21/2018 5:23 PM
< CONNECTOR >
L3207 1-246-226-11 METAL CHIP 15 0.5% 1/8W
CN5008 1-842-052-21 CONNECTOR, FFC/FPC (LIF) 20P
CN5009 1-793-331-31 CONNECTOR, FFC/FPC (LIF) 20P < TRANSISTOR >
*************************************************************
Q3208 6-553-482-01 TR SSM3J56MFV
9 A-2107-088-A MAIN BOARD, COMPLETE (for SERVICE) *************************************************************
(US, CND)
9 A-2107-150-A MAIN BOARD, COMPLETE (for SERVICE) (AEP) OLED CHUKEI PC BOAR BOARD
9 A-2107-159-A MAIN BOARD, COMPLETE (for SERVICE) (UK) **************************
9 A-2107-210-A MAIN BOARD, COMPLETE (for SERVICE) (E12)
9 A-2107-762-A MAIN BOARD, COMPLETE (for SERVICE) (AUS) < CAPACITOR >

9 A-2107-776-A MAIN BOARD, COMPLETE (for SERVICE) (SP) C5008 1-118-047-11 CERAMIC CHIP 10uF 10% 16V
9 A-2107-842-A MAIN BOARD, COMPLETE (for SERVICE) (LA9)
9 A-2107-983-A MAIN BOARD, COMPLETE (for SERVICE) (AR) < CONNECTOR >
9 A-2119-853-A MAIN BOARD, COMPLETE (for SERVICE) (EA)
********************* CN5002 1-843-407-31 FPC CONNECTOR (ZIF) (11PIN)
CN5003 1-816-654-61 FFC/CONNECTOR, FPC (LIF) 6P
< DIODE > CN5004 1-842-052-21 CONNECTOR, FFC/FPC (LIF) 20P
CN5005 1-816-654-61 FFC/CONNECTOR, FPC (LIF) 6P
D3200 6-503-735-01 DI BZT52H-C4V3
< DIODE >
< IC >
D5000 6-503-196-01 DI CL-194S-HB8SP-SD-T
IC1000 6-721-742-01 IC TAS5614LA
IC1001 6-718-103-01 IC TAS5538DGGR < IC >
IC1002 6-721-742-01 IC TAS5614LA
IC2003 6-722-554-01 IC CXD90040R-B (MAIN board Suffix-12) IC5001 6-600-629-01 IC RS-470
IC2005 6-720-801-01 IC EM638165TSD-6G *************************************************************

IC2009 6-722-554-01 IC CXD90040R-B (MAIN board Suffix-13) SPEAKER CHUKEI PC BOAR BOARD
IC3000 6-720-030-01 IC TPS2065CDBVR *****************************
IC3001 6-722-615-01 IC TC7WHU04FK,RSNJ (CT
IC3200 6-718-999-01 IC MM1839A50NRE < TRANSFORMER >
IC3201 6-721-694-01 IC RT7272BGSP
TB6000 1-780-454-11 TERMINAL BOARD (SPEAKER) 4P
TB6001 1-780-815-11 TERMINAL BOARD (SPEAKER)
Note 1: When the complete MAIN board is replaced, re- *************************************************************
fer to “NOTE OF REPLACING THE IC1000 AND
IC1002 ON THE MAIN BOARD AND THE COM-
PLETE MAIN BOARD” on page 5.

Note 2: When the complete MAIN board is replaced,

spread the bond referring to“BOND FIXATION OF
ELECTRIC PARTS” on page 6.

33
HT-RT3
Ver. 1.3
TOUCH USB

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
TOUCH BOARD ACCESSORIES
************ ************

< CONNECTOR > 4-587-771-13 MANUAL, INSTRUCTION

(ENGLISH (US), LATIN SPANISH, CANADIAN
CN4001 1-816-654-61 FFC/CONNECTOR, FPC (LIF) 6P FRENCH) (US, CND)
4-587-771-21 MANUAL, INSTRUCTION
< IC > (ENGLISH) (UK, SP, AUS, E12)
4-587-771-31 MANUAL, INSTRUCTION
IC4001 6-722-496-01 IC CY8CMBR3108-LQXIT (FRENCH, SPANISH, GERMAN) (AEP)
IC4002 6-713-333-01 IC PST8429UL 4-587-771-41 MANUAL, INSTRUCTION
************************************************************* (DUTCH, ITALIAN, POLISH) (AEP)
4-587-771-51 MANUAL, INSTRUCTION
A-2089-365-A USB BOARD, COMPLETE (TRADITIONAL CHINESE, FRENCH, ARABIC,
******************** PERSIAN) (SP)

< CONNECTOR > 4-587-771-61 MANUAL, INSTRUCTION

(ENGLISH, ARABIC) (EA)
CN7000 1-843-975-11 USB CONNECTOR (A) 4-587-771-71 MANUAL, INSTRUCTION (LATIN SPANISH) (LA9)
************************************************************* 4-587-771-81 MANUAL, INSTRUCTION (LATIN SPANISH) (AR)
501 1-493-155-11 REMOTE COMMANDER RMT-AH200U
MISCELLANEOUS (Remote control)
************** 502 1-848-225-21 CABLE, LIGHT PLUG (Optical digital cable)
(US, CND, AEP, UK)
3 8-989-602-00 RC-S730 (WW)
4 1-828-156-51 WIRE (FLAT TYPE) (6 CORE) 503 1-849-353-11 HDMI CABLE (High Speed HDMI cable)
6 1-828-230-51 WIRE (FLAT TYPE) (20 CORE) (EA, SP, AR, AUS, E12, LA9)
10 1-859-169-21 LOUDSPEAKER 16CM 0 504 1-785-504-21 ADAPTOR, CONVERSION (AC plug adaptor) (LA9)
54 1-828-218-51 WIRE (FLAT TYPE) (18 CORE)

55 1-493-097-11 BLUETOOTH MODULE 501 Remote control (1) 502 Optical digital cable (1)
0 102 1-855-244-11 DC FAN (US, CND, AEP, UK)
104 1-828-228-51 WIRE (FLAT TYPE) (20 CORE)
0 105 4-966-267-12 BUSHING (FBS001), CORD
0 106 1-834-966-42 POWER-SUPPLY CORD (AEP, SP, LA9)

0 106 1-835-068-21 CORD, POWER (AUS)

0 106 1-837-308-12 CORD, POWER-SUPPLY (US, CND)
0 106 1-837-312-11 CORD, POWER-SUPPLY (AR) 503 High Speed HDMI cable (1) 504 AC plug adaptor* (1) (LA9)
0 106 1-839-999-22 POWER-SUPPLY CORD (UK, EA) (EA, SP, AR, AUS, E12, LA9) * The adaptor is not use in Chile,
0 106 1-848-053-12 POWER-SUPPLY CORD (E12) Uruguay and Paraguay. Use the adaptor
in the countries where it is neccessary.

0 107 1-474-638-11
REGULATOR, SWITCHING 3L405W-2
(EXCEPT E12)
0 107 1-474-638-21 REGULATOR, SWITCHING 3L405W-3 (E12)
*************************************************************

Note 1: If wire (flat type) is replaced, install it after bending it

in the same form as that before replacement.

Note 2: When the REGULATOR, SWITCHING 3L405W

board is replaced, spread the bond referring to
“BOND FIXATION OF ELECTRIC PARTS” on page
6.

Note 3: When the BLUETOOTH MODULE or RC-S730

(WW) is replaced, refer “NOTE OF REPLACING
BLUETOOTH MODULE OR RC-S730 (WW)” on
page 5.

34
 HT-RT3

MEMO

UFOELK - 2/21/2018 5:23 PM

35
HT-RT3

REVISION HISTORY

Ver. Date Description of Revision

1.0 2016.03 New
1.1 2016.06 Addition of Argentina, Latin-American and Singapore models.
Add Abbreviation for E12 in page 13.
Add IC Pin Function Description of IC4001 in page 29.
Change description of MANUAL, INSTRUCTION for US and Canadian models in ACCESSORIES
section.
Change P/N of POWER-SUPPLY CORD for AEP model in page 32 and page 34.
Change P/N of Ref. No. 10 in page 34.
Change P/N and description of Ref. No. for TB6001 in SPEAKER CHUKEI PC BOAR board.
Delete of CN2008 and S2000 in MAIN board.
Delete of duplicate WIRE (FLAT TYPE) (6 CORE) in page 30 and 34.
1.2 2016.08 Add “0” mark for Ref. No. 504 in ACCESSORIES section.
Change of MAIN board (Suffix 12,13).
Change of IC2009 and IC3205 to complete MAIN board in page 18.
Change of IC2009 in MAIN board to IC2003 (MAIN board Suffix-12) and IC2009 (MAIN
board Suffix-13) in page 20 and 21.
Change of Ref. No. IC1000 to IC1002 in page 20.
Change of Ref. No. IC1002 to IC1000 in page 20.
Change quantity of AC plug adaptor (LA9) in SPECIFICATIONS and ACCESSORIES sections.
1.3 2017.02 Add note of “NOTE OF REPLACING BLUETOOTH MODULE OR RC-S730 (WW)” in page 5, 30, 31
and 34.
Add P/N and description of L3207 on MAIN board in page 33.
Add P/N and description of C5008 on OLED CHUKEI PC BOAR board in page 33.
Add troubleshooting flow (6. Display panel is not functioned) in page 18.
Change P/N of Ref. No. 10 in page 30 and 34.

1.4 2017.07 Correction of TROUBLESHOOTING (SMR-17020)

1.5 2017.09 Addition of Part No. for Ref. No. IC2003, IC2005, IC2009, IC3001 and IC3204 on MAIN board (SMR-17027)

How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.

e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.