TEKNOLOGI CADD MEKANIKAL

(MINYAK & GAS)

Edisi Pertama Januari 2013

Edisi Kedua September 2014

Institusi Latihan Jabatan Tenaga Manusia

http ://www.jtm.gov.my/kurikulum

Hak Cipta Terpelihara. Dokumen ini diklasifikasikan sebagai TERHAD. Tidak dibenarkan
mengeluar mana-mana bahagian dalam kandungan Sukatan Latihan dalam apa jua
bentuk tanpa keizinan daripada Jabatan Tenaga Manusia (JTM).

SUKATAN LATIHAN: A17 SIJIL TEKNOLOGI CADD MEKANIKAL ( MINYAK & GAS )
SEMESTER 1 hingga 3 merupakan dokumen yang menggariskan perkara-perkara yang
perlu diperolehi oleh seorang graduan di dalam bidang kemahiran Pelukis Pelan ( Minyak
& Gas ). Sukatan latihan ini dibangunkan mengikut format Institusi Latihan Jabatan
Tenaga Manusia (ILJTM) dan telah mengambil kira Standard Kemahiran Pekerjaan
Kebangsaan (National Occupational Skill Standard – NOSS) serta Kurikulum Unit
Kompetensi (Curriculum of Competency Unit -CoCU) daripada Jabatan Pembangunan
Kemahiran (JPK) iaitu perubahan dokumen yang berasaskan Unit Kompetensi (CU) dan
Aktiviti Kerja (WA) yang memenuhi standard persijilan kemahiran Malaysia.

Kod Pengesahan Sukatan Latihan : SFB/A17/22003/P1(22014)

Tarikh Pengesahan Sukatan Latihan : 30 SEPTEMBER 2014
 PENGESAHAN JAWATANKUASA PEMANDU KURIKULUM JTM
KLUSTER PEMBUATAN

Dengan ini dimaklumkan bahawa silibus Kluster Pembuatan bagi kursus peringkat Sijil
Teknologi CADD Mekanikal (Minyak & Gas) telah disemak dan DISAHKAN dalam
Mesyuarat Jawatankuasa Pemandu Kurikulum JTM bil. 2/2014 yang diadakan pada 30
September 2014. Sehubungan itu, silibus yang telah disahkan ini hendaklah digunapakai
bermula JULAI 2015 diseluruh Institut Latihan Jabatan Tenaga Manusia.

.................................................. ............................................................
(MOHD NUZI BIN YAACOB) (SYED MOHAMAD NOOR BIN SYED MAT ALI)
Pengerusi Kluster Pengerusi Mesyuarat Jawatankuasa
Pemandu Kurikulum
 KANDUNGAN

1. PENDAHULUAN ...................................................................................................... vi

1.1. Pengenalan.......................................................................................................vi
1.2. Objektif .............................................................................................................vi
1.3. Pra-syarat .........................................................................................................vi
1.4. Tempoh Latihan ............................................................................................... vii
1.5. Kaedah Latihan................................................................................................ vii
1.5.1. Struktur Silibus ..................................................................................... vii
1.5.2. Struktur Rujukan NOSS ....................................................................... viii
1.6. Peluang Kerjaya ...............................................................................................ix

2. AHLI JAWATANKUASA ......................................................................................... 10

3. SEMESTER 1 .......................................................................................................... 11

3.1. Carta Profil ...................................................................................................... 12

3.2. Carta Aliran Latihan ........................................................................................ 13
3.3. Carta Perbandingan ........................................................................................ 15
3.4. Jadual Pembahagian Jam Kredit .................................................................... 16
3.5. Jadual Pengalaman Pembelajaran ................................................................. 17
A17-01-01 : Fundamental Workshop Practise ................................................. 17
A17-01-02 : Drawing Management ................................................................. 18
A17-01-03 : Fundamental Engineering Drawing .............................................. 19
A17-01-04 : Projection Drawing ...................................................................... 20
A17-01-05 : Detail Drawing ............................................................................. 21
A17-01-06 : Assembly Drawing ....................................................................... 22
3.6. Profil Silibus .................................................................................................... 23
A17-01-01 : Fundamental Workshop Technology ........................................... 23
A17-01-02 : Drawing Management ................................................................. 26
A17-01-03 Fundamental Engineering Drawing ............................................... 30
A17-01-04 Projection Drawing ....................................................................... 36
A17-01-05 Detail Drawing .............................................................................. 39
A17-01-06 Assembly Drawing ........................................................................ 51

4. SEMESTER 2 .......................................................................................................... 55

4.1. Carta Profil ...................................................................................................... 56

4.2. Carta Aliran Latihan ........................................................................................ 57
4.3. Carta Perbandingan ........................................................................................ 59
4.4. Jadual Pembahagian Jam Kredit .................................................................... 61
4.5. Jadual Pengalaman Pembelajaran ................................................................. 62
A17-02-01 : Fundamental Process Concept.................................................... 62
A17-02-02 : Communication Practice .............................................................. 63
A17-02-03 : Process Design ........................................................................... 64
A17-02-04 : Site Surveying ............................................................................. 65
A17-02-05 : General Arrangement Drawing .................................................... 66
4.6. Profil Silibus .................................................................................................... 67
 A17-02-01 : Fundamental Process Concept.................................................... 67
A17-02-02 : Communication Practice .............................................................. 73
A17-02-03 : Process Design ........................................................................... 77
A17-02-04 : Plant Surveying ........................................................................... 85
A17-02-05 : General Arrangement Drawing .................................................... 93

5. SEMESTER 3 .......................................................................................................... 99

5.1. Carta Profil ................................................................................................... 100

5.2. Carta Aliran Latihan ...................................................................................... 101
5.3. Carta Perbandingan ...................................................................................... 103
5.4. Jadual Pembahagian Jam Kredit .................................................................. 104
5.5. Jadual Pengalaman Pembelajaran ............................................................... 105
A17-03-01 : 3D Piping Design ....................................................................... 105
A17-03-02 : Pipe Support Drawing ................................................................ 106
A17-03-01 : Isometric Drawing ...................................................................... 107
A17-03-04 : Cost Estimation ......................................................................... 108
A17-03-05 : Resource Management ............................................................. 109
A17-03-06 : Piping Project ............................................................................ 110
5.6. Profil Silibus .................................................................................................. 111
A17-03-01 : 3D Piping Design ....................................................................... 111
A17-03-02 : Pipe Support Drawing ................................................................ 119
A17-03-03 : Isometric Drawing ...................................................................... 122
A17-03-04 : Cost Estimation ......................................................................... 125
A17-03-05 : Resource Management ............................................................. 132
A17-03-06 : Piping Project ............................................................................ 137
 SENARAI SINGKATAN

L Lecture
D Demo
P Practice
PT Practical Test
PR Project
A Assignment
OT Oral Test
WT Written Test
O Others
IS Information Sheet
AS Assignment Sheet
WS Work Sheet
1. PENDAHULUAN

1.1. Pengenalan

Sukatan latihan ini merupakan dokumen yang menggariskan perkara-perkara yang

perlu diperolehi oleh seseorang pelajar di dalam bidang kemahiran Teknologi CADD
Meknikal (Minyak & Gas). Semua modul yang terkandung di dalam sukatan latihan
ini akan dinilai berasaskan keterampilan bagi memastikan setiap pelajar
berkebolehan dan berkeupayaan melaksanakan modul-modul berkenaan mengikut
tahap kemahiran yang dipelajari.
Sukatan latihan ini dibangunkan mengikut format sukatan Institusi Latihan Jabatan
Tenaga Manusia (ILJTM) dan telah mengambil kira Standard Kemahiran Pekerjaan
Kebangsaan (National Occupational Skills Standard – NOSS) yang dibuat oleh
Jabatan Pembangunan Kemahiran (JPK). Sukatan latihan ini juga mengambil kira
penambahan semua duti dan tugasan selaras dengan keperluan teknologi semasa
dan memenuhi standard persijilan.

1.2. Objektif

Objektif sukatan latihan ini dibangunkan adalah untuk membantu pensyarah dalam
menyediakan pembelajaran latihan kemahiran agar keseragaman latihan dapat
dilakukan di semua ILJTM bagi kursus Teknologi CADD Mekanikal (Minyak & Gas).

1.3. Pra-syarat

Kursus Teknologi CADD Mekanikal (Minyak & Gas) merupakan kursus peringkat
Sijil Teknologi yang dikendalikan oleh Jabatan Tenaga Manusia (JTM). Syarat
kelayakan bagi kursus ini ialah calon mesti warganegara Malaysia berumur di
antara 17 hingga 30 tahun dan mempunyai kelulusan akademik berikut :

 Kemasukan ke Semester 1

Syarat kemasukan:
1. Lepasan Sijil Pelajaran Malaysia (SPM)
a) Mempunyai SPM dengan kepujian dalam 3 subjek berikut :
i. Bahasa Melayu
ii. Sains / Fizik / Kimia
iii. Matematik / MatematikTambahan
b) Lulus Bahasa Inggeris
c) Lulus dalam sesi temuduga yang dijalankan

vi
 2. Lepasan Sijil Kemahiran Malaysia (SKM)
a) Mempunyai SKM Tahap 2 dalam salah satu bidang berikut :
i. CADD Mekanikal (Pembuatan)
ii. Teknologi Minyak & Gas
iii. Pengeluaran / Pembuatan
iv. Kimpalan (Gas &Arka)
v. Kimpalan (Minyak & Gas)
vi. Fabrikasi Logam
b) Lulus dalam sesi temuduga yang dijalankan.

1.4. Tempoh Latihan

 Kemasukan ke Semester 1

Tempoh latihan sepenuh masa bagi kursus ini ialah 1 tahun 9 bulan.
Pelajar diwajibkan menjalani latihan kemahiran selama satu tahun enam
bulan (dari semester 1 hingga semester 3) dan selepas semester 3,
pelajar perlu menjalani latihan industri (industrial training) selama tiga
bulan.

1.5. Kaedah Latihan

Kaedah latihan di ILJTM bagi peringkat sijil adalah berteraskan kemahiran di mana
70% ialah latihan amali dan 30% pengajaran teori.

1.5.1. Struktur Silibus

Silibus yang digunapakai bagi kursus Sijil Teknologi CADD Mekanikal

(Minyak & Gas) adalah seperti berikut:

vii
 Jadual 1 : Struktur Silibus Kursus Teknologi Minyak dan Gas
(Mechanical Plant - Downstream)

Semester Silibus ILJTM Rujukan NOSS

OG-022-3 Piping Drafting

OG-015-1 Mechanical Plant

A17 Teknologi CADD Mekanikal
1 Maintenance
(Minyak & Gas)
MC-080-3 Manufacturing
Draughtman

A17 Teknologi CADD Mekanikal

2 OG-022-3 Piping Drafting
(Minyak & Gas)

A17 Teknologi CADD Mekanikal

3 OG-022-3 Piping Drafting
(Minyak & Gas)

4 Latihan Industri Tiada

1.5.2. Struktur Rujukan NOSS

Jadual 2 : Struktur NOSS yang dirujuk dari sub sektor:

Mechanical Plant Maintenance untuk Tahap 3

Teknologi CADD Mekanikal

TAHAP
(Minyak & Gas)

5 OG-022-5

4 OG-022-4

3 OG-022-3

2 TIADA

1 TIADA

viii
1.6. Peluang Kerjaya

Pelajar lepasan sijil teknologi bagi kursus ini mempunyai peluang kerjaya sebagai
a) Pelukis Pelan (Perpaipan Minyak & Gas)

b) Pelukis Pelan (Struktur)

c) Pelukis Pelan (Pembuatan)

ix
2. AHLI JAWATANKUASA

Jawatankuasa Pembangunan Silibus

Kursus Teknologi CADD Mekanikal (Minyak&Gas)

1. Mohd Nuzi Bin Yaacob

ADTEC Kemaman
(Pengerusi Kluster)
2. Hamidom Bin Ngah
ILP Ipoh
(Penolong Pengerusi Kluster)
3. Siti Nur Insyirah Pamela Binti Abdullah
ILP Selandar
(Ketua Penyelaras)
4. Mohd Taib Bin Md Shariff
ILP Selandar
(Penolong Penyelaras)
5. Dahyian Bin Mohamad Dahlan @ Pusa ILP Kota Kinabalu
6. Asbul Hadi Bin Mat Yunus ILP Selandar

Urusetia
1. Hafazah Binti Jaffar Ibu Pejabat
2. Afande Bin Ibrahim Ibu Pejabat

Sesi 1
Tarikh : 14 - 17 April 2014
Tempat : Hotel Star City, Alor Setar, Kedah

Sesi 2
Tarikh : 5 – 8 Mei 2014
Tempat : Felda Residence, Tekam

Sesi 3
Tarikh : 23 – 26 Jun 2014
Tempat : Hotel Midah, Kuala Lumpur

Sesi 4
Tarikh : 8 – 11 September 2014
Tempat : Hotel Adamson, Kuala Lumpur

10
3. SEMESTER 1

SEMESTER 1

11
 3.1. Carta Profil

K12 TEKNOLOGI PEMASANGAN PAIP MINYAK DAN GAS (SEMESTER 4)

SECTOR OIL & GAS

SUB SECTOR OIL, GAS & PETROCHEMICAL

JOB AREA PIPE DRAFTING (OIL & GAS)

NOSS TITLE PIPING DRAFTING (OIL & GAS)

JOB LEVEL THREE (3) JOB AREA CODE

COMPETENCY COMPETENCY UNIT

MECHANICAL MECHANICAL
PIPING DRAWING PLANT WORKSHOP
DRAWING DRAWING
DOCUMENT ACTIVITIES
CORE SKETCHING DEVELOPMENT
CONTROL (OG-015-1:2012-C01)
(MC-080-3:2013-C01) (MC-080-3:2013-C02)
OG-022-3:2013-C03 07 08 09

COMPUTER AIDED
DESIGN AND
DRAFTING
(MC-080-3:2013-C04)
10

12
 3.2. Carta Aliran Latihan

A17 SIJIL TEKNOLOGI CADD-MEKANIKAL (MINYAK DAN GAS) – SEMESTER 1

MULA

Use standard lettering,

FUNDAMENTAL symbol and layout
FUNDAMENTAL
Demonstrate personal ENGINEERING
WORKSHOP
safety DRAWING
PRACTISE 08.01a 1/3
07.01a 1/2
A17-01-01 A17-01-03 Draw geometrical
Perform work piece construction
measurement
08.01b 2/3
07.01 2/2

Perform mechanical
drawing sketching
08.01 3/3

DRAWING Determine drafting

MANAGEMENT document control
requirements Develop orthographic
PROJECTION drawing
03.01 1/3 DRAWING
A17-01-02 09.03 1/2

Develop isometric
Perform drafting A17-01-04
drawing
document control
09.02 2/2
03.02 2/3

Check drafting
document control status
conformance

03.03 3/3

13
 A

Draw two dimensional

DETAIL mechanical drawing
DRAWING
09.01 1/4

Develop two
A17-01-05
dimensional sectional
drawing

09.04 2/4

Prepare drawing Bill of

Materials

09.05 3/4

Perform CADD two

dimensional mechanical
drawing

10.01 4/4

Perform CADD
ASSEMBLY assembly drawing
DRAWING development
10.02 1/1
A17-01-06

BERSAMBUNG
KE
SEMESTER 2

14
 3.3. Carta Perbandingan

A17 – SIJIL TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) - SEMESTER 1

PROJECTION DRAWING
WORKSHOP PRACTICE

ASSEMBLY DRAWING
MODULE TITLE

DETAIL DRAWING
SILIBUS JTM

FUNDAMENTAL

FUNDAMENTAL
MANAGEMENT

ENGINEERING
DRAWING

DRAWING
NOSS (FORMAT BARU)

NUMB

01-01

01-02

01-03

01-06

01-05

01-06
A17-

A17-

A17-

A15-

A17-

A17-
WA
NO
CU

ER
CU TITLE
CU WORK ACTIVITY

Determine drafting document

0 03.01
control requirements
PIPING DRAWING
3 Perform drafting document control 03.02
PRODUCTION
Check drafting document control
03.03
status conformance

PLANT Perform work piece measurement 07.01

1 WORKSHOP
ACTIVITIES Demonstrate personal safety 07.01a

Use standard lettering, symbol and

TECHNICAL 08.01a
layout
9 DRAWING
ACTIVITIES Draw geometrical construction 08.01b

MECHANICAL
Perform mechanical drawing
1 DRAWING 08.01
sketching
SKETCHING
Develop two dimensional
09.01
mechanical drawing
Develop isometric drawing 09.02
MECHANICAL Develop orthographic drawing
2 DRAWING 09.03
DEVELOPMENT
Develop two dimensional sectional
09.04
drawing

Prepare drawing Bill of Materials 09.05

Perform CADD two dimensional

COMPUTER 10.01
mechanical drawing development
4 AIDED DESIGN
AND DRAFTING Perform CADD assembly drawing
10.02
development

15
3.4. Jadual Pembahagian Jam Kredit

A17 SIJIL TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) – SEMESTER 1

JAM KREDIT
TASK
A/(PEMBERAT (1.5) X 20 )
KOD MODUL TAJUK MODUL JAM JAM JUMLAH
TEORI AMALI KREDIT
KREDIT KREDIT JAM
(JAM) (JAM) MODUL
TEORI AMALI KREDIT
A17-01-01 FUNDAMENTAL WORKSHOP PRACTISE 18 42 0.6 1.4 2.0 2.0
A17-01-02 DRAWING MANAGEMENT 9 21 0.3 0.7 1.0 1.0
A17-01-03 FUNDAMENTAL ENGINEERING DRAWING 36 84 1.2 2.8 4.0 4.0
A17-01-04 PROJECTION DRAWING 27 63 0.9 2.1 3.0 3.0
A17-01-05 DETAIL DRAWING 36 84 1.2 2.8 4.0 4.0
A17-01-06 ASSEMBLY DRAWING 18 42 0.6 1.4 2.0 2.0

JUMLAH LATIHAN ( SUBJEK TERAS ) 114 336 4.8 11.2 16.0 16

PERATUS LATIHAN ( SIJIL ) 30% 70%
MK 1011 MATEMATIK KEJURUTERAAN 1 30 - 1.0 - 1.0 1
SK 1021 SAINS KEJURUTERAAN 1 30 - 1.0 - 1.0 1
PI 1031 / PM 1041 PENDIDIKAN ISLAM 1 / PENDIDIKAN MORAL 1 30 - 1.0 - 1.0 1
BI 1051 BAHASA INGGERIS 1 30 - 1.0 - 1.0 1
KK 1071 KO-KURIKULUM 30 WH
JUMLAH LATIHAN ( SUBJEK UMUM ) 150.0 - 5.0 - 5.0 4
JUMLAH KESELURUHAN LATIHAN 630.0 20

16
3.5. Jadual Pengalaman Pembelajaran

JADUAL PENGALAMAN PEMBELAJARAN

A17-01-01 : Fundamental Workshop Practise

Terminal Performance Objective:

Carry Out Fundamental Workshop Practice using personal protective equipment (PPE), safety outfit and measuring tools so that
personal safety demonstrated and workpiece measurement performed in accordance with Occupational Safety and Health Act
(OSHA), Standard Operating Procedure (SOP) and manufacturing requirement.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Demonstrate personal safety using personal protective equipment and safety

LE 1 : DEMONSTRATE PERSONAL SAFETY
outfit so that all personal safety demonstrated in accordance with
Occupational Safety and Health Act (OSHA).

Perform work piece measurement using various types of measuring tools so

that types of measuring tools identified, measuring techniques determined,
LE 2 : PERFORM WORK PIECE MEASUREMENT metric and imperial units practiced, surface flatness of material /equipment is
verified, outside and inside diameter of work piece are measured in
accordance with Standard Operating Procedure (SOP) and manufacturing
requirement.

17
 JADUAL PENGALAMAN PEMBELAJARAN
A17-01-02 : Drawing Management

Terminal Performance Objective:

Carry Out Drawing Management using drawings, filing systems, various storage types, computer, office application and company
procedures so that drafting document control requirement identified and drafting document control performed in accordance with the
company’s standard, rules and regulations.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

LE 1 : IDENTIFY DRAFTING DOCUMENT CONTROL Identify drafting document control requirements using piping drawings and filing
REQUIREMENTS systems so that various types of drawings classified and filing systems are
identified according to company’s standard, rules and regulations.
Perform drafting document control using computer and office application
software, drawing scanning tools, filing systems, Master Distributed Registration
LE 2 : PERFORM DRAFTING DOCUMENT CONTROL (MDR), media storages and company procedures so that MDR produced,
drawings sorted, properly stored and the document control changes status
updated in accordance to company’s standard, rules and regulations.

18
 JADUAL PENGALAMAN PEMBELAJARAN
A17-01-03 : Fundamental Engineering Drawing

Terminal Performance Objective:

Perform Fundamental Engineering Drawing using drafting equipment so that drawing equipment utilised, geometrical construction drawn
and mechanical drawing sketching performed in accordance with drawing standard requirement.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

LE 1 : UTILISE DRAWING EQUIPMENT Utilize drawing equipment using drafting equipment so that correct materials choosed, standard
lettering, symbol, layout and techniques used in accordance to drawing standard requirement.

LE 2 : DRAW GEOMETRICAL CONSTRUCTION Draw geometrical drawing using drafting equipment so that various shapes and sizes identified and
geometrical construction drawn in accordance to drawing standard requirement.

Perform mechanical drawing sketching using drafting equipment so that actual sample and object
LE 3 : PERFORM MECHANICAL DRAWING
visualised, sketching view angle ascertained, sketching techniques and procedure used in
SKETCHING
accordance to drawing standard requirement.

19
 JADUAL PENGALAMAN PEMBELAJARAN
A17-01-04 : Projection Drawing

Terminal Performance Objective:

Construct Projection drawing using drafting equipment so that orthographic and isometric drawing developed in accordance to drawing
standard requirement.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Develop orthographic drawing using drafting equipment so that orthographic principles

LE 1 : DEVELOP ORTHOGRAPHIC DRAWING
interpreted and orthographic view drawing produced in accordance to drawing standard
requirement

LE 2 : DEVELOP ISOMETRIC DRAWING Develop isometric drawing using drafting equipment so that isometric principles interpreted
and isometric drawing detail produced in accordance to drawing standard requirement

20
 JADUAL PENGALAMAN PEMBELAJARAN

A17-01-05 : Detail Drawing

Terminal Performance Objective:

Carry out Detail Drawing using drafting tools, standard engineering parts’ tables, stationeries computer and CAD software so that
part drawing constructed and CAD 2D drawing performed in accordance with standard mechanical engineering drafting procedure.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Construct Part Drawing using drafting tools, standard engineering parts’

tables and stationeries so that drawing scale and dimension ascertained,
part drawing detail and sectional view detail produced, bill of materials
LE 1 : CONSTRUCT PART DRAWING
instruction interpreted, bill of materials table content confirmed and updated
drawing produced in accordance with standard mechanical engineering
drafting procedure.

Perform CADD 2D drawing using computer and CAD software so that CAD
interface, drawing tools and modify tools ascertained, annotation commands
LE 2 : PERFORM CAD 2D DRAWING and layers generated, title block format used, drawing orientation and
drawing scale determined, and plotting outcome confirmed in accordance
with standard mechanical engineering drafting procedure.

21
 JADUAL PENGALAMAN PEMBELAJARAN

A17-01-06 : Assembly Drawing

Terminal Performance Objective:

Carry out Assembly Drawing using computer and CAD software so that CAD assembly drawing development performed in
accordance with standard mechanical engineering drafting procedure.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Perform CAD Assembly Drawing Development using computer and CAD

software so that assembly drawing requirements produced, assembly
drawing tools, equipment, instruments and materials listed, layer (by different
LE 1 : PERFORM CAD ASSEMBLY DRAWING colour and line) created, assembly component development and import
DEVELOPMENT assembly component executed, assembly symbol printed, cutting plane
(sectioning) developed, multi sectioning area view produced, object material
and hatching process executed and line accuracy interpreted in accordance
with standard mechanical engineering drafting procedure.

22
 3.6. Profil Silibus

SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 18
Course : TEKNOLOGI CADD MEKANIKAL ( MINYAK DAN GAS) Practical Credit Hours : 42
Semester : 1 Total Credit Hours : 42
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry Out Fundamental Workshop Practice using personal protective equipment (PPE), safety outfit and measuring tools so that personal safety
demonstrated and workpiece measurement performed in accordance with Occupational Safety and Health Act (OSHA), Standard Operating Procedure
(SOP) and manufacturing requirement.

Module : A17-01-01 : Fundamental Workshop Technology

Assessment
Methods

Methods
Delivery

WIM
CoCU / Work Activities No. : OG-015-1:2012-C01 / 07.01a, 07.01

Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : DEMONSTRATE PERSONAL SAFETY
17.1 1.1 Make safe working condition.
17.2 1.1.1 Identify personal safety and safe working
condition. 12 L IS
A
17.3 1.1.2 Describe the purpose Personal Protective AS
WT
Equipments (PPE).
17.4 1.1.3 Explain the condition on layout of working
place and workshop

23
 Assessment
Module : A17-01-01 : FUNDAMENTAL WORKSHOP TECHNOLOGY

Methods

Methods
Delivery

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2 Wear safety outfit. 15 P PT IS

17.5 WS
17.6 1.2.1 Demonstrate how to wear Personal
Protective Equipments (PPE).
1.2.2 Practice personal safety and safe
working
17.7 condition.
1.2.3 Obey to workshop safety rules and regulations.

LE 2 : PERFORM WORK PIECE MEASUREMENT

6 17.8 L WT IS
2.1 Identify of Measuring tools AS
2.1.1 Metric and Imperial Units.
2.1.2 Type of the measuring tools:
 Straight Edge
 Spirit Level
 Steel Rule
 Feeler Gauge
 Vernier Calliper
 Micrometer
 Dial Gauge
 Bore Gauge
 Depth Gauge
 Height Gauge
2.1.3 Measuring techniques

24
 Assessment
Module : A17-01-01 : FUNDAMENTAL WORKSHOP TECHNOLOGY

Methods

Methods
Delivery

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.2 Used of measuring tools

2.2.1 Use of the measuring tools

2.2.2 Apply metric and imperial units.
2.2.3 Apply measuring technique
PT IS
2.2.4 Measure inside diameter, depth of grooves 27 P
WS
and length of a work piece.
2.2.5 Measure shaft outside diameter and shaft
run
2.2.6 Verify surface flatness of material /
equipment.

Total Hours 48 72

Tools/ Equipment/ Materials : Safety Password, PPE, Stationery, Log book.

1. Sutton, I. (2012). Offshore Safety Management. ISBN 9781437735246
2. OSHA. Occupational Safety and Health Act 1994. Malaysia
Reference Books (Tittle, Atr, Publisher) : 3. Industry Code of Practice for Safe Working in a Confined Space 2010; Department of Occupational Safety and
Health, Ministry of Human Resources,Malaysia
Manuals : Not Applicable

25
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 1.6
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 2.4
Semester : 1 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :

Carry out Drafting Document Control using piping drawings, filing systems, various storage types,computer and office application, and
company procedures so that drafting document control requirement identified, drafting document control performed and status conformance
checked in accordance with the company standard, rules and regulations.

Module : A17-01-02 : Drawing Management

Delivery Methods

Assessment
CoCU / Work Activities No. : OG-022:2013-C03 / 03.01, 03.02, 03.03

Methods

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 IDENTIFY DRAFTING DOCUMENT CONTROL REQUIREMENTS

1.1 Determine drafting document control 3 L WT IS
requirements AS
1.1.1 Company’s rules and regulations
1.1.2 Types of piping drawing
 Revision drawing
 New drawing
 Related drawing

26
Module : A17-01-02 : Drawing Management

Delivery Methods

Assessment
CoCU / Work Activities No. : OG-022:2013-C03 / 03.01, 03.02, 03.03

Methods

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.3 Filing system

 Flow chart
 Label
 File index
 Drawing index

1.1.4 Interpret company’s rules and regulations.

1.1.5 Identify piping drawing. IS
3 P PT
1.1.6 Identify types of filing system. WS

LE 2 : PERFORM DRAFTING DOCUMENT CONTROL

2.1 Perform drafting document control
Document transmittal
2.1.2 Plant requirement Types of office application
Software
2.1.3 Master Drawing Registration (MDR) 3 IS
2.1.4 Type of scanning tools L WT
AS
 Portable Document Format (PDF)
 Image format

2.1.5 Drawing stage

27
Module : A17-01-02 : Drawing Management

Delivery Methods

Assessment
CoCU / Work Activities No. : OG-022:2013-C03 / 03.01, 03.02, 03.03

Methods

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

 IFC – Issue For Construction

 AFC – Approve For Construction
2.1.6 Document sorting methods
 Sequence
 Service
 Area
 Discipline
2.1.7 Types of filing system
2.1.8 Piping document storage
 Document transmittal
 Location
 Storage media

2.1.9 Arrange document transmittal for distribution

2.1.10 Apply software application.
2.1.11 Carry out master drawing registration
(MDR).
IS
2.1.12 Carry out piping drawing to scan file. 12 P PT
WS
2.1.13 Interpret drawing stage.
2.1.14 Perform document sorting.
2.1.15 Apply filing system.
2.1.16 Carry out piping document storage.

28
Module : A17-01-02 : DRAWING MANAGEMENT

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022:2013-C03 / 03.01, 03.02, 03.03

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2. Check drafting document control status

conformance

2.1.3 Drawing stage 3 IS

2.1.4 Types of piping drawing L WT
AS
 Revision drawing
 New drawing
2.2.3 Types of office application software
2.1.5 Interpret drawing stage
2.1.6 Check piping drawing. IS
2.1.7 Apply software application. 6 P PT
WS
Update document control changes.

9 21

Piping drawings, filing systems, various storage types, computer and office application, and company
ools/ Equipment/ Materials :
procedures
1. David L. Goetsch. (2005) Technical Drawing Fifth Edition, Thomson Delmar Learning. ISBN 1-4018-
5760-4. ,
Reference Books (Tittle, Atr, Publisher) : 2. R.K. Dhawan (2002) Lukisan Mesin Dalam Unjuran Sudut Pertama, Golden . ISBN 983-72-0467-2
3. James D. Bethune. (2002) Engineering Graphics With AutoCAD 2007, Prentice Hall. ISBN 0-13-
238942-8
Manuals : Not Applicable

29
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 36
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 84
Semester : 1 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :

Perform Fundamental Engineering Drawing using drafting equipment so that drawing equipment utilised, geometrical construction drawn and
mechanical drawing sketching performed in accordance with drawing standard requirement.

Module : A17-01-03 Fundamental Engineering Drawing

Assessment
Methods

Methods
Delivery

WIM
CoCU / Work Activities No. : MC-080-3:2013-C01 / 08.01a, 08.01b, 08.01

Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : UTILISE DRAWING EQUIPMENT
1.1 Identify basic equipment used by the drafter

1.1.1 Identify proper uses and functions of drawing 3 L WT IS

equipment AS
1.1.2 Specify safe handling, care and maintenance of
equipment
1.2 Select the right tools to create drawing 4.5 P PT IS
WS
1.2.1 Operate proper equipment accordingly

30
Module : A17-01-03 FUNDAMENTAL ENGINEERING DRAWING

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : MC-080-3:2013-C01 / 08.01a, 08.01b, 08.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.3 Choose type of lettering, paper size, standard
symbol, standard layout, projection

1.3.1 Identify size of lettering , according to drawing

standard
1.3.2 List several types of paper sizes & standard IS
3 L WT
layouts AS
1.3.3 Define standard symbol & SI units
1.3.4 Identify various types of line and how they are used

1.3.5 Provide standard layout & title block

1.3.6 Write freehand letters by using lettering
technique
1.3.7 Write letters by using template
IS
18 P PT
1.3.8 Draw various line types according to the WS
drawing standard
1.3.9 Draw line, angle, arcs & circle of specified
size using drawing instrumen

31
Module : A17-01-03 FUNDAMENTAL ENGINEERING DRAWING

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : MC-080-3:2013-C01 / 08.01a, 08.01b, 08.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 2 : DRAW GEOMETRICAL CONSTRUCTION
2.1 Determine geometrical problems
2.1.1 Identify various geometrical shapes & sizes.
IS
2.1.2 Determine geometrical construction technique. 9 L WT
AS
2.1.3 Define the meaning of target point.

2.2 Use geometrical construction techniques to

solve the geometrical problem

2.2.1 Draw various types of lines

2.2.2 Draw any size angle
2.2.4 Draw four different types of triangle and five types IS
27 P PT
of parallelograms. WS
2.2.5 Draw a regular triangle, square, hexagon and
octagon.
2.2.6 Divide a space into equal parts, divide any angle in
half and divide a line into equal parts.
2.2.7 Draw lines and arcs tangents to each other.

32
Module : A17-01-03 FUNDAMENTAL ENGINEERING DRAWING

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : MC-080-3:2013-C01 / 08.01a, 08.01b, 08.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 3 : PERFORM MECHANICAL DRAWING SKETCHING

3.1 Prepare mechanical drawing sketching
requirements

3.1.1 Identify types of tools, material and equipment.

3.1.2 Mechanical drawing sketching resources
requirements
 sketching concepts IS
9 L WT
 sketching information requirement AS
 sketching resources requirements
3.1.3 Identify type of freehand sketching
 Orthogonal
 Oblique
 Isometric

3.1.4 Utilize types of tools, material and equipment

3.1.5 Generate mechanical drawing sketching instruction
IS
and requirements summary. 4.5 P PT
WS
3.1.6 Conclude mechanical drawing sketching
instruction and requirements .

33
Module : A17-01-03 FUNDAMENTAL ENGINEERING DRAWING

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : MC-080-3:2013-C01 / 08.01a, 08.01b, 08.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

3.2 Perform 2D sketching

3.2.1 Identify object shape in the sketch

3.2.2 Identify basic ideas and illustrations
 Customer requirements & specification
IS
 Product/object specification 6 L WT
AS
 Actual sample visualisation
3.2.3 Sketching Object orientation
3.2.4 Sketching view angle selection

3.2.5 Create freehand sketching with correct techniques

3.2.6 Apply mechanical drawing sketching techniques.
 parrallel, perpendicular and evenly spaced lined
IS
 circle 18 P PT
WS
 arc
 ellipse

34
Module : A17-01-03 FUNDAMENTAL ENGINEERING DRAWING

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : MC-080-3:2013-C01 / 08.01a, 08.01b, 08.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

3.3 Perform 3D sketching

3.3.1 Identify type of 3D sketching

 Oblique IS
6 L WT
i. Cavalier AS
ii. Cabinet
 Isometric

IS
3.3.2 Apply 3D sketching techniques 12 P PT
WS

Total Hours 34 84

Tools/ Equipment/ Materials : Personal protective equipment (PPE) and various measuring tools.
1. David A.Madsen, Engineering Drawing and Design 2nd Edition, ISDN 0-8273-6720
Reference Books (Tittle, Atr, Publisher) : 2. Thomas E. France, Mechanical Drawing CAD-Communication 12th Edition, ISDN 0-02-667958-2
3. Goetsch Nelson Chalk, Technical Drawing 4th Edition, ISDN 0-7668-0531-x
Manuals :

35
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 27
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 63
Semester : 1 Total Credit Hours :3
NOSS Code : OG-022-3
Terminal Performance Objective :

Construct Projection drawing using drafting equipment so that orthographic and isometric drawing developed in accordance to drawing standard
requirement.

Delivery Methods
Module: A17-01-04 Projection Drawing

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02 / 09.02, 09.03

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 DEVELOP ORTHOGRAPHIC DRAWING

1.1 Obtain data and drawing sheet

1.1.1 Collecting data

 3D object
 Drawing sheet IS
15 L WT
1.1.2 Orthographic Drawing principles. AS
 1st Angle
 3rd Angle

36
Module : A17-01-04 PROJECTION DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02 / 09.02, 09.03

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.3 Orthographic view drawing development

 Front View
 Right view
 Left view
 Side view
 Bottom View
 Top view
 Auxiliary view

1.1.4 Obtain orthographic drawing requirements 39 P PT IS

1.1.5 Determine orthographic drawing Scale and WS
dimension.
1.1.6 Develop orthographic view drawing

LE 2 : DEVELOP ISOMETRIC DRAWING

2.1 Obtain data and drawing sheet

2.1.1 Determine isometric drawing requirements

 3D object
 Drawing sheet.

37
Module : A17-01-04 PROJECTION DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02 / 09.02, 09.03

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.2 Determine isometric drawing method. 12 L WT IS

 Regular AS
 Reverse
 Long-axis
2.1.3 Interpret isometric drawing techniques.
 Circle four center
 Curve
 Isometric angle and non isometric lines
2.1.4 Obtain isometric drawing requirements 24 P PT IS
2.1.5 Apply isometric drawing method. WS
2.1.6 Apply isometric drawing techniques.
2.1.7 Develop isometric drawing
Total Hours 27 63

Tools/ Equipment/ Materials : Personal protective equipment (PPE) and various measuring tools.
1. David A.Madsen, Engineering Drawing and Design 2nd Edition, ISDN 0-8273-6720
Reference Books (Title, Atr, Publisher) : 2. Thomas E. France, Mechanical Drawing CAD-Communication 12th Edition, ISDN 0-02-667958-2
3. Goetsch Nelson Chalk, Technical Drawing 4th Edition, ISDN 0-7668-0531-x
Manuals : Not Applicable

38
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 36
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 84
Semester : 1 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry out Detail Drawing using drafting tools, standard engineering parts’ tables, stationeries computer and CAD software so that part drawing
constructed and CAD 2D drawing performed in accordance with standard mechanical engineering drafting procedure.

Module : A17-01-05 Detail Drawing

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : CONSTRUCT PART DRAWING

1.1 Develop two dimensional mechanical drawing

1.1.1 Type of dimensions

 Size
 Location
IS
1.1.2 Types of dimension styles 3 L WT
AS
 Radius
 Angular
 Linear
 Diameters
 Leader

39
Module : A17-01-05 DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.3 Type of dimensioning standard

 ANSI
 BS (British Standard)
 ISO
1.1.4 Text alignment system
 Aligned
 Horizontal
 ISO
1.1.5 Dimensioning techniques
 Straight edge
 Slant
1.1.6 Dimensioning classification
 Functional dimension
 Non-functional dimension
 Tolerance dimension
 Additional dimension
1.1.7 Identify type of dimensions
1.1.8 Identify types of dimension styles
1.1.9 Interpret type of dimensioning standard
IS
1.1.10 Interpret text alignment system 9 P PT
WS
1.1.11 Interpret dimensioning techniques
1.1.12 Interpret dimensioning classification

40
Module : A17-01-05 DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2 Screw thread detailing

1.2.1 Type of thread
 External thread (Male)
 Internal Thread (Female)
1.2.2 Threading shapes
 ISO
 Unified
 Sharp V
 Whitworth
 Square
 Acme IS
6 L WT
 Buttress AS
 Worm
 Knuckle
1.2.3 Number of thread per inch (N.T.P.I)
1.2.4 Direction of rotation
 Right Hand Thread (Clockwise)
 Left Hand Thread (Counter clockwise)
1.2.5 Screw thread draw techniques
 Detail
 Schematic
 Simplified

41
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2.1 Identify type of thread

1.2.2 Interpret threading shapes
IS
1.2.3 Interpret number of thread per inch (N.T.P.I) 9 P PT
WS
1.2.4 Identify direction of rotation
1.2.5 Draw screw thread
1.3 Fastener detailing
1.3.1 Type of fastener IS
1.5 L WT
 Temporary AS
 Fix
1.3.2 Identify type of fastener IS
3 P PT
1.3.2 Draw fastener detailing WS
1.4.1 Type of key
 Square Key
 Flat Key
 Gib Head Key
IS
 Woodruff Key 3 L WT
AS
 Pratt & Whitney
 Feather Key
 Spline Key
 Round Key

42
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.4.2 Identify type of keys IS

1.5 P PT
1.4.3 Draw key detailing WS
1.5.1 Type of Washer
 Spring
 Lock
IS
o External 1.5 L WT
AS
o Internal
o External-Internal
 Taper
1.5.2 Identify type of washer IS
1.5 P PT
1.5.3 Draw washer detailing WS
1.6 Surface Texture and Machining Symbols
1.6.1 Surface finishing
1.6.2 Machining Symbols
 Obligatory
 Optional
3 L WT
 Prohibited
1.6.3 Indication of surface texture
1.6.4 Lay symbols
1.6.5 Surface texture symbols
1.6.6 Surface roughness tester

43
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.6.7 Determine surface finishing

1.6.8 Identify type of machining symbols
1.6.9 Interpret indication of surface texture IS
9 P PT
1.6.10 Identify lay symbols WS
1.6.11 Identify texture symbols
1.6.12 Test surface roughness
1.7 Create section view

1.7.1 Data collection

 Sectioning concept
 Drawing placement
1.7.2 Type of section view
 Full IS
9 L WT
AS
 Half
 Offset
 Aligned
 Unsanctioned Features
 Intersections in sections
 Conventional revolutions

44
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

 Broken-Out sections
 Auxiliary sections
 Conventional breaks
 Revolved sections
 Removed section
1.7.3 Direction of cutting plane
 Placement of cutting-plane lines.
 Applications of the different cutting-plane line
styles.
1.7.4 Sectional view development
1.7.5 Type of hatch pattern
 Angle
 Island
 Selection
1.7.6 Variations of hatch pattern
 Linear
 Crosshatching
 Contoured

45
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.7.7 Choose correct section view

1.7.8 Create section view IS
21 P PT
1.7.9 Apply direction of cutting plane WS
1.7.10 Apply of hatch pattern

LE 2 : PERFORM CAD 2D DRAWING

2.1 Perform CADD two dimensional Mechanical
Drawing development

2.1.1 Examine Mechanical Drawing instruction

 source
 authority
 validity
 requirements IS
6 L WT
AS
 assignment objectives
2.1.2 CADD mechanical drawing requirements
 mechanical drawing sketches and drawing
information
 drawing tools and equipments.

46
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.3 Mechanical Drawing CADD scale and

dimension.
 two dimension drawing requirements
 paper formats and units
 drawing dimension style
 standard line layers and thickness
 drawing base length
 drawing scale.
2.1.4 Develop CADD plan elevation development
 lines based on standard line layers and
thickness
 construction line
 object line
 hidden line
 drawing symbols
2.1.5 CADD side & end elevation development
 generate Projection line
 determine intersection points
 develop object line
 clear projection line.

47
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.6 CADD Mechanical Drawing dimensions

preparation
 dimension detail
 information accuracy
 dimension line
 dimension style consistencies
2.1.7 CADD Mechanical Drawing detail preparation
 font/lettering size
 drawing detail
 detail spelling
 mechanical drawing detail.
 detail spelling
 font consistencies
2.1.8 CADD Mechanical Drawing title block
preparation
 mechanical title block detail
 title block format
 title block detail
 drawing title and identification number
 signatories line and arrangements
 detail spelling and font consistencies

48
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.9 Examine Mechanical Drawing instruction

2.1.10 Obtain CADD mechanical drawing
requirements
2.1.11 Determine Mechanical Drawing CADD Scale
and dimension
IS
2.1.12 Develop CADD plan elevation 27 P PT
WS
2.1.13 Develop CADD side and end elevation
2.1.14 Prepare CADD Mechanical Drawing
dimensions
2.1.15 Prepare CADD Mechanical Drawing detail
2.1.16 Prepare CADD Mechanical Drawing title block
2.1.17 Generate CADD Mechanical Drawing
 plotter requirements
 page setup manager
 plotter / printer features
 paper size
IS
 plotting scale 3 L WT
AS
 plotting style table for pen assignments
 drawing orientation
 drawing scale
 plotting outcome checking

49
Module : A17-01-05 : DETAIL DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C02, MC-080-3:2013-C04 / 09.01, 09.04, 09.05, 10.01

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.18 Mechanical drawing submission process

 information accuracy checking
 drawing submission check list
 drawing folding method
 mechanical drawing log book
 mechanical drawing digital filing

2.1.19 Generate CADD Mechanical Drawing IS

6 P PT
2.1.20 Carry out Mechanical drawing submission WS
36 84

Stationeries, Drawing folder, Work instructions, Office equipments, Client standard, CAD software,
Tools/ Equipment/ Materials :
Instrument diagram, Computer, Plotter
1. David L. Goetsch. (2005) Technical Drawing Fifth Edition, Thomson Delmar Learning. ISBN 1-
4018-5760-4
2. R.K. Dhawan (2002) Lukisan Mesin Dalam Unjuran Sudut Pertama, Golden . ISBN 983-72-0467-
Reference Books (Tittle, Atr, Publisher) :
2
3. James D. Bethune. (2002) Engineering Graphics With AutoCAD 2007, Prentice Hall. ISBN 0-13-
238942-8
Manuals :

50
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 18
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 42
Semester : 1 Total Credit Hours :2
NOSS Code : OG-022-3
Terminal Performance Objective :

Carry out Assembly Drawing using computer and CAD software so that CAD assembly drawing development performed in accordance with
standard mechanical engineering drafting procedure.

Module : A17-01-06 Assembly Drawing

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C04 / 10.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : PERFORM CAD ASSEMBLY DRAWING DEVELOPMENT

1.1.1 Assembly drawing concept and application
1.1.2 Assembly drawing principles
1.1.3 Assembly drawing purposes
1.1.4 Assembly Drawing instruction
1.1.5 CADD Assembly drawing requirements IS
3 L WT
 Obtain mechanical drawing sketches and AS
drawing information
 Obtain CADD mechanical drawing tools and
equipments
 Gather mechanical drawing requirements

51
Module : A17-01-06 : ASSEMBLY DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C04 / 10.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.6 Assembly drawing requirements preparation

 Targeted 2 Dimensional drawing file
 Assembly drawing specification
 Assembly drawing tools, equipment,
instruments and materials
 Layer (by different colour and line).
 Assembly component development/ Import
assembly component
 Part layer changes (for assembling).
 Component reference point development
1.1.7 Examine Assembly Drawing instruction
IS
1.1.8 Obtain CADD Assembly drawing requirement 9 P PT
WS
1.1.9 Prepare Assembly drawing requirements
1.1.10 Assembly drawing development
 Main drawing preparation
 Component assembling
 assemble & dissemble layer Locking IS
15 L WT
systems AS
 Develop assembly symbol (such as. welding,
GD&T)

52
Module : A17-01-06 : ASSEMBLY DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C04 / 10.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

 Develop cutting plane ( sectioning )

 Develop multi sectioning area view
 Develop object material
 Conduct hatching process
 Check line accuracy
1.1.11 Prepare Assembly drawing detail
 Obtain drawing detail
 Check information accuracy
 Select font/lettering size
 Balloon creation
 Bill of material provision
 Bill of material information
 Scale drawing development
 Drawing detail indication & development.
 Detail spelling checking
 Font consistencies checking
1.1.12 Mechanical drawing submission
implementation
 Assembly drawing final checking
 Assembly drawing detail accuracy checking
 Drawing submission check list
 Mechanical drawing log book update

53
Module : A17-01-06 ASSEMBLY DRAWING

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : MC-080-3:2013-C04 / 10.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.13 Develop Assembly drawing

1.1.14 Prepare Assembly drawing detail IS
33 P PT
1.1.15 Carry out Mechanical drawing submission WS

18 42

Stationeries, Drawing folder, Work instructions, Office equipments, Client standard, CAD software,
Tools/ Equipment/ Materials :
Instrument diagram, Computer, Plotter
1. David L. Goetsch. (2005) Technical Drawing Fifth Edition, Thomson Delmar Learning. ISBN 1-
4018-5760-4
2. R.K. Dhawan (2002) Lukisan Mesin Dalam Unjuran Sudut Pertama, Golden . ISBN 983-72-0467-
Reference Books (Tittle, Atr, Publisher) :
2
3. James D. Bethune. (2002) Engineering Graphics With AutoCAD 2007, Prentice Hall. ISBN 0-13-
238942-8
Manuals :

54
4. SEMESTER 2

SEMESTER 2

55
 4.1. Carta Profil

SECTOR OIL & GAS

SUB SECTOR OIL, GAS & PETROCHEMICAL

JOB AREA PIPE DRAFTING (OIL & GAS)

NOSS TITLE PIPING DRAFTING (OIL & GAS)

JOB LEVEL THREE (3) JOB AREA CODE

COMPETENCY COMPETENCY UNIT

PIPING MATERIAL PIPING DRAFTING

PIPING DRAWING PIPING SITE
TAKE-OFF SUPERVISORY
CORE PRODUCTION SURVEYING
PREPARATION FUNCTION

OG-022-3:2013-C01 OG-022-3:2013-C02 OG-022-3:2013-C04 OG-022-3:2013-C05

FUNDAMENTAL
CORE AIDED VALUE PROCESS CONCEPT

10A

56
 4.2. Carta Aliran Latihan

A17 SIJIL TEKNOLOGI CADD MEKANIKAL ( MINYAK & GAS ) - SEMESTER 2

MULA

Study work instruction

Determine the process in
FUNDAMENTAL PROCESS
oil and gas
PROCESS DESIGN
CONCEPT 01.01 1/5
10A.01 1/3

A17 – 02 – 01 A17 – 02 – 03
Estimate pipes and Prepare drawing tools
components quantity requirement

01.02 2/5
04.03 2/3
Produce key plan
Carry out pipeline drawing
sketching
01.03 3/5
10A.02 3/3
Produce hook-up
drawing

01.09 4/5

Check piping drawing

Apply good
COMMUNICATION 01.08 5/5
communication skill
PRACTISE
05.07a 1/3

A17 – 02 – 02
Carry out work briefing

05.01 2/3

Carry out section

meeting

05.05 3/3

57
 B

SITE Study work instruction

SURVEYING

02.01 1/4
A17 – 02 – 04

Carry out site visit

preparation

02.02 2/4

Perform site visit as-

built

02.03 3/4

Submit site visit report /

daily report

02.04 4/4

GENERAL
ARRANGEMENT Construct structure
general arrangement
DRAWING
drawing

A15 – 02 – 05 01.10a 1/4

Incorporate equipment
layout drawing

01.04 2/4

Prepare hazardous
area drawing

01.10b 3/4

Produce piping general

arrangement drawing
(GA)

01.05 4/4
BERSAMBUNG
KE
SEMESTER 3

58
4.3. Carta Perbandingan

A17 – SIJIL TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) - SEMESTER 2

COMMUNICATION PRACTICE

GENERAL ARRANGEMENT
FUNDAMENTAL PROCESS
MODULE TITLE

PROCESS DESIGN

SITE SURVEYING
JTM SYLLABUS

DRAWING
CONCEPT
NOSS (New Format)

A17-02-01

A17-02-02

A17-02-03

A17-02-04

A17-02-05
NUMBER
CU NO

WA
CU TITLE CU WORK ACTIVITY

Study Work Instruction 01.01

Prepare Drawing Tools

01.02
Requirement

Produce Key Plan Drawing 01.03

Incorporate Equipment
01.04
Layout Drawing
PIPING DRAWING Produce Piping General
01 01.05
PRODUCTION Arrangement Drawing (GA)
Check Piping Drawing 01.08

Produce Hook-Up Drawing 01.09

Construct Structure General
01.10a
Arrangement Drawing
Prepare Hazardous Area
01.10b
Drawing

Study Work Instruction 02.01

Carry Out Site Visit

02.02
PIPING SITE Preparation
2 SURVEYING
Perform Site Visit As-Built 02.03

Submit Site Visit Report /

02.04
Daily Report
PIPING MATERIAL
Estimate Pipes and
4 TAKE-OFF 04.03
Components Quantity
PREPARATION

59
 COMMUNICATION PRACTICE

GENERAL ARRANGEMENT
FUNDAMENTAL PROCESS
MODULE TITLE

PROCESS DESIGN

SITE SURVEYING
JTM SYLLABUS

DRAWING
CONCEPT
NOSS (New Format)

A17-02-01

A17-02-02

A17-02-03

A17-02-04

A17-02-05
NUMBER
CU NO

WA
CU TITLE CU WORK ACTIVITY

Carry Out Work Briefing 05.01

5 PIPING DRAFTING
SUPERVISORY Carry Out Section Meeting 05.05
FUNCTION
Apply Good Communication
05.07a
Skill
Determine the Process in Oil
IDENTIFY 10A.01
and Gas
10A CONCEPTUAL
PROCESS Carry Out Pipeline Sketching 10A.02

60
4.4. Jadual Pembahagian Jam Kredit

A17 SIJIL TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) – SEMESTER 2

JAM KREDIT
TASK
A/(PEMBERAT (1.5) X 20 )
KOD MODUL TAJUK MODUL JAM JAM JUMLAH
TEORI AMALI KREDIT
KREDIT KREDIT JAM
(JAM) (JAM) MODUL
TEORI AMALI KREDIT
A17-02-01 FUNDAMENTAL PROCESS CONCEPT 27 63 0.9 2.1 3.0 3.0
A17-02-02 COMMUNICATION PRACTICE 18 42 0.6 1.4 2.0 2.0
A17-02-03 PROCESS DESIGN 36 84 1.2 2.8 4.0 4.0
A17-02-04 SITE SURVEYING 27 63 0.9 2.1 3.0 3.0
A17-02-05 GENERAL ARRANGEMENT DRAWING 36 84 1.2 2.8 4.0 4.0

JUMLAH LATIHAN ( SUBJEK TERAS ) 114 336 4.8 11.2 16.0 16

PERATUS LATIHAN ( SIJIL ) 30% 70%

MK 2011 MATEMATIK KEJURUTERAAN 2 30 - 1.0 - 1.0 1
SK 2021 SAINS KEJURUTERAAN 2 30 - 1.0 - 1.0 1
PENDIDIKAN ISLAM 2 / PENDIDIKAN
PI 2031 / PM 2041 30 - 1.0 - 1.0 1
MORAL 2
BI 2051 BAHASA INGGERIS 2 30 - 1.0 - 1.0 1
KK 2071 KO-KURIKULUM 2 30 - 1.0 - 1.0 WH
JUMLAH LATIHAN ( SUBJEK UMUM ) 150.0 - 5.0 - 5.0 4
JUMLAH KESELURUHAN LATIHAN 630.0 20

61
 4.5. Jadual Pengalaman Pembelajaran

JADUAL PENGALAMAN PEMBELAJARAN

A17-02-01 : Fundamental Process Concept

Terminal Performance Objective:

Apply Fundamental Process Concept using process plant layout , piping design manuals, codes and standards register, reference drawing,
interface information, snapshot and drawing tools so that the process in oil and gas determined and process flow sketching prepared in
accordance with company standard and mechanical engineering (oil and gas) drafting procedure.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Determine the process in oil and gas using process plant layout , piping
LE 1 : DETERMINE THE PROCESS IN OIL AND GAS design manuals, codes and standards register so that various symbol and
process in oil and gas determined in accordance with company standard.

Prepare process flow sketching using drawing tools, reference drawing,

interface information and snapshot tools so that interface sketching carried
LE 2 : PREPARE PROCESS FLOW SKETCHING
out in accordance with company standard and mechanical engineering (oil
and gas) drafting procedure.

62
 JADUAL PENGALAMAN PEMBELAJARAN

A17-02-02 : Communication Practice

Terminal Performance Objective:

Carry Out Communication Practise using various effective communication techniques and medium, job scheduling/job order,
participants list, meeting agenda’s and Audio Visual Aid (AVA) equipments so that good communication skill applied, work briefing
and section meeting carried out according to company standard, rules and regulations.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Apply good communication skill using various effective communication

techniques and medium, AVA equipments and relevant documents so that
LE 1 : APPLY GOOD COMMUNICATION SKILL
good communication skill practised according to company rules,
requirements and standard operating procedure.

Carry out work briefing using list of briefing agenda’s, job scheduling/job
order, AVA equipments and stationeries so that briefing objectives and
LE 2 : CARRY OUT WORK BRIEFING
agendas identified and job scheduling/job order interpreted according to
company rules, requirements and standard operating procedure.

Carry out section meeting using job requirements and instructions, meeting
agendas, participant lists, meeting documents, stationeries, AVA equipments
LE 3 : CARRY OUT SECTION MEETING and recorder tool so that meeting requirements identified, meeting carried
out, the result reviewed and recorded according to company rules,
requirements and standard operating procedure.

63
 JADUAL PENGALAMAN PEMBELAJARAN

A17-02-03 : Process Design

Terminal Performance Objective:

Carry out Process Design using computer, piping software, process control manuals, codes and standard register so that basic cad
piping system applied, key plan drawing produced, piping and instrument diagram (P&ID) drawing validated in accordance with
company standard and mechanical engineering (oil and gas) drafting procedure.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Apply basic CAD piping system using computer and piping software so that
LE 1 : APPLY BASIC CAD PIPING
basic and function of CAD piping system used in accordance with company’s
SYSTEM
standard and mechanical engineering (oil and gas) drafting procedure.

Produce key plan drawing using computer, piping software, process control
manuals, codes and standard register so that piping information identified ,
LE 2 : PRODUCE KEY PLAN DRAWING process flow diagram, piping and instrument diagram (P&ID) drawing created
in accordance with company standard and mechanical engineering (oil and
gas) drafting procedure.

64
 JADUAL PENGALAMAN PEMBELAJARAN

A17-02-04 : Site Surveying

Terminal Performance Objective:

Perform Plant Surveying using work scope and schedule, company’s and authority body’s rules and regulations, permit to work,
reference drawing and measuring instrument so that site visit preparation and site visit performed in accordance with company safety
rules and regulations.

PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH

(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Perform site visit preparation using work scope and schedule, company’s
LE 1 : PERFORM SITE VISIT PREPARATION and authority body’s rules and regulations and permit to work (PTW) so that
work scope identified and site visit requirement complied in accordance to
company safety rules and regulations.

Perform site visit using transportation, reference drawing, measuring

LE 2 : PERFORM SITE VISIT
instrument and safety equipment so that site visit performed and site report
prepared in accordance with company safety rules and regulations.

65
 JADUAL PENGALAMAN PEMBELAJARAN

A17-02-05 : General Arrangement Drawing

Terminal Performance Objective:

Carry Out General Arrangement Drawing using computer, structure general arrangement documents, standard piping and
instrument symbols (reference) document so that single level platform constructed and piping general arrangement drawing (GA)
produced in accordance with company standard and mechanical engineering (oil and gas) drafting procedure.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Construct single level platform layout using computer, structure general

arrangement documents, standard piping and instrument symbols
LE 1 : CONSTRUCT SINGLE LEVEL PLATFORM (reference) document so that primary structure requirement identified,
LAYOUT structure drawing executed, types of equipment item listed , equipment
location layout interpreted and produced in accordance with company
standard and mechanical engineering (oil and gas) drafting procedure.

Produce piping general arrangement drawing (GA) using computer and P&ID
LE 2 : PRODUCE PIPING GENERAL drawing so that dimension, elevation, tagging, line number, evacuation plan
ARRANGEMENT DRAWING (GA) and procedures identified and confirmed, hazardous areas classified and
general arrangement (GA) drawing produced in accordance with company
standard and mechanical engineering (oil and gas) drafting procedure.

66
 4.6. Profil Silibus

SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 27
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 63
Semester : 2 Total Credit Hours :3
NOSS Code : OG-022-3
Terminal Performance Objective :
Apply Fundamental Process Concept using process plant layout , piping design manuals, codes and standards register, registration’s master list
location, filing record, reference drawing, interface information, snapshot and drawing tools so that the process in oil and gas determined and
freehand sketching prepared in accordance with company standard and mechanical engineering (oil and gas) drafting procedure.

Module : A17-02-01 : Fundamental Process Concept

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10A.01, 04.03, 10A.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : DETERMINE THE PROCESS IN OIL AND GAS

1.1 Introduction to Process Plant Layout and
Piping Design

1.1.1 Process Description and Flow Diagram

1.1.2 Plant Layout Fundamentals IS
1.1.3 Procedures and Workflow Methods used in 9 L WT
AS
Plant Layout and Piping Design
1.1.4 Piping Materials
1.1.5 Physical Quantities and Units in Plant Layout
and Piping Design

67
Module : A17-02-01 : Fundamental Process Concept

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10A.01, 04.03, 10A.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.6 Determine Process Flow Diagram

1.1.7 Determine Piping Materials IS

12 P PT
WS
 Cast Iron Pipe
 Plastic Pipe
1.2 Components of a Piping System

1.2.1 Fittings
 Elbow
 Weld Tee
 Stub In
 Coupling
 Reducers
 Screwed
 Socket Weld
IS
3 L WT
AS
1.2.2 Flanges

 Weld Neck
 Threaded
 Socket Weld
 Slip-On
 Lap-Joint
 Reducing
 Blind
 Orifice

68
Module : A17-02-01 : Fundamental Process Concept

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10A.01, 04.03, 10A.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2.3 Valves

 Gate Valve
 Globe Valve
 Angle Valve
 Check Valve
 Ball Valve
 Butterfly Valve
 Relief Valve
 Control Valve
1.2.4 Determine types of

 Fittings
 Flanges IS
12 P PT
 Valves WS

1.2.5 Draw Piping Symbols

69
Module : A17-02-01 : Fundamental Process Concept

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10A.01, 04.03, 10A.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.3 Equipment Used in Process Plants

1.3.1 Process Equipment
1.3.2 Mechanical Equipment

 Vessel
 Ladders, Cages, and Platforms
IS
 Pumps 6 L WT
AS
 Compressors
 Exchangers
 Cooling Tower
 Heater / Boiler

1.3.3 Plant Layout Specifications

18 P PT IS
WS
1.3.4 Determine process equipment
1.3.5 Determine mechanical equipment
1.3.6 Plot Plans

70
Module : A17-02-01 : Fundamental Process Concept

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10A.01, 04.03, 10A.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 2 : CARRY OUT PIPELINE SKETCHING

2.1 Identify pipe and instrument diagram

2.1.1 Piping and Instrument Drawing (P&ID)

 Flow diagram usage
 Piping Arrangement
 Piping symbol

2.1.2 Part drawing Technique

 Flow plan arrangement
 Flow diagram instrument IS
9 L WT
 Pipe and instrument diagram drawing AS
creating techniques

2.1.3 Part in piping system.

 Type and material for gasket
 Type of valves and instruments

2.1.4 Piping Part drawing

2.1.5 Isometric Projection

71
Module : A17-02-01 : Fundamental Process Concept

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10A.01, 04.03, 10A.02

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.6 Interpret Piping and Instrument Drawing (P&ID)

2.1.7 Identify Piping Parts.
2.1.8 Produce Piping Part drawing
IS
21 P PT
2.1.9 Identify Type and material for gasket. WS
2.1.10 Identify type of valves and instruments.
2.1.11 Comply Piping Part drawing.

Total Hours 27 63

Tools/ Equipment/ Materials : Job scheduling/job order, participants list, meeting agenda’s and Audio Visual Aid (AVA) equipments
1. Ed Bausbacher, Roger Hunt (1993), Process Plant Layout and Piping Design, Prentice Hall, ISBN-
10 : 0131386298, ISBN-13: 978-0131386297

2. Richard J. Beale, Paul Bowers, Peter Smith (2010), Plant Layout And Construction Design, Gulf
Publishing Company, ISBN-10: 1933762373, ISBN-13: 978-193376237
Reference Books (Tittle, Atr, Publisher) :
3. George A. Antaki(2003), Piping and Pipeline Engineering Design, Construction,Maintenance,
Integrity and Repair, Marcel Dekker Inc, ISBN: 0-8247-0964-0

4. Analysis, Synthesis and Design of Chemical Processes(2002), Pearson Education, ISBN : 0-13-
064792-6

Manuals :

72
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 18
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 42
Semester : 2 Total Credit Hours :2
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry Out Communication Practise using various effective communication techniques and medium, job scheduling/job order,
participants list, meeting agenda’s and Audio Visual Aid (AVA) equipments so that good communication skill applied, work briefing
and section meeting carried out according to company standard, rules and regulations.

Module : A17-02-02 : Communication Practice

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022:2013-C05 / 05.01, 05.05, 05.07a

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : APPLY GOOD COMMUNICATION SKILL

1.1 Apply good communication skill

1.1.1 Type of communication IS

1.1.2 Communication barrier 6 L WT
AS
1.1.3 Language (written and spoken)

1.1.4 Memo and letter writing

1.1.5 Presentation skills IS
21 P PT
WS

73
Module : A17-02-02 : Communication Practice

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022:2013-C05 / 05.01, 05.05, 05.07a

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 2 : CARRY OUT WORK BRIEFING

2.2 Carry out work briefing

2.1.1 Job scheduling/job order

IS
6 L WT
2.1.2 Company’s policy, rules and regulations AS

2.1.3 Daily briefing objectiveDaily briefing

2.1.5 Interpret Job scheduling / job order.

2.1.6 Comply with Company’s policy, rules and

regulations
IS
2.1.7 Identify daily briefing objective. 10.5 P PT
WS
2.1.8 Identify daily briefing agenda.

2.1.9 Execute daily briefing.

74
Module : A17-02-02 : Communication Practice

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022:2013-C05 / 05.01, 05.05, 05.07a

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 3 : CARRY OUT SECTION MEETING

3.1 Prepare work schedule
3.1.1 Work schedule format
3.1.2 Master schedule
3.1.3 Types of resources
IS
 Manpower 6 L WT
AS
 Material
 Methods

3.1.4 Company’s target

75
Module : A17-02-02 : Communication Practice

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022:2013-C05 / 05.01, 05.05, 05.07a

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

3.1.1 Identify schedule format.

3.1.2 Interpret master schedule.

3.1.3 Identify Resources availability and capability

3.1.4 Identify Company’s target. 10.5 P PT

IS
WS
3.1.5 Plan drafting schedule.

3.1.6 Produce drafting schedule.

3.1.7 Submit drafting schedule to superior.

Total Hours 18 42

Tools/ Equipment/ Materials : Job scheduling/job order, participants list, meeting agenda’s and Audio Visual Aid (AVA) equipments
1. Lihui Wang (2007), Process Planning and Scheduling for Distributed Manufacturing, Springer, ISBN:
978-1-84-628751-0
2. Alan Dalton (1998), Safety, Health and Environmental Hazards at the Workplace, Cengage
Learning, ISBN:978-0-30-433291-5
Reference Books (Tittle, Atr, Publisher) :
3. Dan Hopwood, Steve Thompson(2006), Workplace safety a guide for small and midsized
companies, John Wiley & Sons Inc., ISBN:978-0-7821-3604-3
4. Gregory T. Haugan, Project Planning and Scheduling, Management Concepts Inc., ISBN 1-56726-
136-1
Manuals :

76
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 36
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 84
Semester : 2 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry out Process Design using computer, piping software, process control manuals, codes and standard register so that basic cad piping
system applied, key plan drawing produced, piping and instrument diagram (P&ID) drawing validated in accordance with company standard and
mechanical engineering (oil and gas) drafting procedure.

Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : APPLY BASIC CAD PIPING SYSTEM

77
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1 Study work instruction

1.1.1 Work instruction
 Work scope
 Time

1.1.2 Technical drawing

 Drawing file name
 File location IS
o Soft copy L WT
AS
9
o Hard copy
 2D software application drawing
 Piping material specification
 Piping classification
 Equipment specification
 Colour coding

1.1.3 Piping & Instrument Diagram (P&ID)

 Process Flow Schematic Drawing(PFSD)

78
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.4 Interpret work scope.

1.1.5 Interpret Work schedule.
1.1.6 Select drawing file name.
1.1.7 Identify file location.
1.1.8 Identify 2D drawing.
1.1.9 Identify pipe material specification.
IS
21 P PT
1.1.10 Identify piping classification. WS
1.1.11 Identify piping classification.
1.1.12 Identify equipment specification.
1.1.13 Identify colour code
1.1.14 Identify process flow schematic drawing.
1.1.15 Identify pipe & instrument diagram.

79
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 2 : PRODUCE KEY PLAN DRAWING

2.3 Produce Key plan Drawing

2.1.1 Piping information

 Location 9 L WT
IS
 Area AS
 Number
 Dimension

2.1.2 Limit continuity (portion to portion)

 Scale
 Dimensioning
 Direction
 Deck

2.1.3 2D mark up key

2.1.4 Identify piping information requirements

2.1.5 Identify limits continuity from one area to
another area of each platform level IS
18 P PT
WS
2.1.6 Incorporate 2D mark up key plan drawing.
2.1.7 Apply 2D CAD software application.

80
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 3 : VALIDATE PIPING AND INSTRUMENT DIAGRAM (P&ID) DRAWING

3.1 Produce Hookup drawing

3.1.1 Tie-in list

 Tie-in number
 Line pipe number
 Location
IS
6 L WT
AS
3.1.2 Piping & instrument diagram (P&ID)

3.1.3 2D mark-up drawing

 General arrangement drawing (GA)
 Isometric drawing
 Material Take- Off (MTO)
3.1.4 Prepare Tie-in list.
3.1.5 Interpret piping & instrument diagram (P&ID)
3.1.6 Incorporate general arrangement drawing
(GA). IS
24 P PT
3.1.7 Incorporate isometric drawing. WS

3.1.8 Incorporate Material Take-Off (MTO).

3.1.9 Produce hook-up drawing.

81
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

3.2 Check Piping drawing

3.2.1 Piping drawing specification

 Scale
 Dimension
 Symbol

3.2.2. Piping material take-off (MTO)

3.2.3 Title block
 Piping drawing number
 Line number
 Revision number
 Drawing title
 Piping line list
IS
12 L WT
3.2.4 Piping routing AS
 Connection
 Flow
 Piping line number

3.2.5 Reference drawing

 Piping & instrument diagram (P&ID)
 General arrangement (GA) drawing

3.2.6 Drawing standard format

 Drawing size
 Drawing title
 Piping drawing number
 Revision number 82
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

3.2.7 Drawing content piping information such as:

 Piping classification
 Line number
 Instrument tagging
 Equipment tagging
 Pipe specification
 Pipe support standard

3.2.8 Colour coding such as:

 Red
 Green
 Blue
 Orange
 Yellow

83
Module : A17-02-03 : Process Design

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C0 / 01.01, 01.02, 01.03,01.09,01.08

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

3.2.9 Check piping drawing specification.

3.2.10 Check Piping Material Take-Off (MTO).
3.2.11 Check Title block.
3.2.12 Check piping routing.
IS
3.2.13 Interpret Reference drawing. 21 P PT
WS
3.2.14 Comply drawing standard format.
3.2.15 Check drawing content piping information.
3.2.16 Apply Colour coding.

Total Hours 36 84

Tools/ Equipment/ Materials : Piping software, process control manuals, codes and standard register
1. Mike W.Lin (1993), Drawing and Designing with Confidence: A Step-by-Step Guide,John Wiley &
Sons, Inc., ISBN-978-0471283904
2. Roy A. Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company, Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
Reference Books (Tittle, Atr, Publisher) :
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-Willcox, ISBN 978-15-907-0247-5
7. Dix and Riley, Discovering Auto CAD 2013, Prentice Hall, ISBN 0-132-95856-2

84
Manuals :
SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 27
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 63
Semester : 2 Total Credit Hours :3
NOSS Code : OG-022-3
Terminal Performance Objective :
Perform Plant Surveying using work scope and schedule, company’s and authority body’s rules and regulations, permit to work, reference drawing
and measuring instrument so that site visit preparation and site visit performed in accordance with company safety rules and regulations.

Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : PERFORM SITE VISIT PREPARATION

85
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1 Study work instruction

1.1.1 Work schedule

 Work location
 Timeline

1.1.2 Work scope – piping IS

3 L WT
AS
 Types of work process
 Pipe line number
 Piping area
 Structure layout
 Equipment layout

86
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.3 Identify work location.

1.1.4 Identify schedule planning.

1.1.5 Interpret work process.

1.1.6 Identify pipe line number. IS

12 P PT
WS
1.1.7 Identify piping area.

1.1.8 Identify structure layout.

1.1.9 Identify equipment layout.

87
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2 Carry out site visit preparation

1.2.1 Company’s rules and regulations

 Basic Offshore Safety Induction and
Emergency Training (BOSIET) cert - (for
platform)
 Work permit cert
 Medical check-up 6 L WT
IS
 Safety brief cert AS

1.2.2 Authority body’s rules and regulations

 Department of Occupational Safety and
Health (DOSH) requirements

1.2.3 Permit to Work (PTW)

1.2.5 Interpret requirements to enter Platform / Plant.

1.2.6 Comply with authority body’s rules and
regulations.
1.2.7 Apply Permit to Work (PTW). IS
12 P PT
1.2.8 Select Measuring instrument. WS
1.2.9 Select reference existing drawing.
1.2.10 Select personal protective equipment (PPE).

88
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 2 : PERFORM SITE VISIT
2.1 Perform site visit –“As-Built”

2.1.1 Reference drawing such as:

 General arrangement (GA) drawing
 Isometric drawing
 P&ID drawing
 Pipe specification drawing
 Plot plan drawing
IS
 Equipment layout drawing 15 L WT
AS
2.1.2 Pipe line number
2.1.3 Equipment number
2.1.4 Modification area
2.1.5 Types of measuring instrument
 Measuring tape

89
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.6 Technique measuring pipe size (Nominal Pipe
Size-NPS) and length
2.1.8 Pipe sketches

2.1.8 Personnel protective equipment

 Coverall
 Safety helmets
 Safety shoes
 Ear plug
 Safety glasses

2.1.9 Interpret reference drawing.

2.1.10 Identify pipe line number.
2.1.11 Identify equipment number.
2.1.12 Identify modification area.
2.1.13 Carry out measuring activity. IS
27 P PT
2.1.14 Carry out piping sketching. WS

2.1.15 Produce site red line mark-up.

2.1.16 Compare pipe routing with technical drawing.
2.1.17 Comply with personnel protective equipment.

90
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.2 Submit site visit report / daily report

2.2.1 Company’s rules and regulations

 Standard Operating Procedure (SOP).

2.2.2 Types of report format

 Manual
IS
 Computerize 3 L WT
AS
2.2.3 Types of document
 Drawing
 Site visit report

2.2.4 Company’s organization chart

2.2.5 Comply with company Standard Operating

Procedure (SOP).
2.2.6 Write site visit report. IS
15 P PT
WS
2.2.7 Compile site visit documentation.
2.2.8 Submit site visit documentation for approval.
2.2.9 Amend site visit documentation.

Total Hours 27 63

91
Module : A17-02-04 : Plant Surveying

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C02 / 02.01, 02.02, 02.03,02.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

Work scope and schedule, company’s and authority body’s rules and regulations, permit to work,
Tools/ Equipment/ Materials : reference drawing and measuring instrument

1. Mike W.Lin(1993),Drawing and Designing with Confidence: A Step-by-Step Guide, John Wiley &
Sons, Inc., ISBN-978-0471283904
2. Roy A. Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company, Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
Reference Books (Tittle, Atr, Publisher) :
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-Willcox, ISBN 978-15-907-0247-5
7. John Muskett, Site Surveying,Wiley-Blackwell, ISBN 0-632-03848-9
Manuals :

92
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 36
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 84
Semester : 2 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry Out General Arrangement Drawing using computer, structure general arrangement documents, standard piping and instrument
symbols (reference) document so that single level platform constructed and piping general arrangement drawing (GA) produced in
accordance with company standard and mechanical engineering (oil and gas) drafting procedure.

Module : A17-02-05 : General Arrangement Drawing

Assessme
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C01 / 01.04, 01.05, 01.10a, 01.10b

WIM
nt
Learning Experience (LE)
Knowledge Hrs Practical Hrs
LE 1 : CONSTRUCT SINGLE LEVEL PLATFORM LAYOUT
1.1 Construct structure general arrangement
drawing

1.1.1 Mechanical structure.

IS
1.1.2 Material 6 L WT
AS
1.1.3 Welding standard

93
Module : A17-02-05 : General Arrangement Drawing

Assessme
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C01 / 01.04, 01.05, 01.10a, 01.10b

WIM
nt
Learning Experience (LE)
Knowledge Hrs Practical Hrs

1.1.4 Determine equipment and structure general

arrangement assembly drawing specification
1.1.5 Illustrate equipment and structure general IS
arrangement assembly drawing 9 P PT
WS
1.1.6 Determine material specification
1.1.7 Determine welding standard

1.2 Incorporate Equipment Layout Drawing

1.2.1 Types of equipment item such as:

 Vessel
 Tank

1.2.3 Equipment item specification such as: IS

12 L WT
 Dimension AS
 Size
 Material

1.2.4 Equipment Location layout

1.2.5 2D mark up equipment layout drawing

1.2.6 Select types of equipment.

1.2.7 Identify equipment specification. IS
1.2.8 Identify equipment location layout. 30 P PT WS
1.2.9 Incorporate equipment layout drawing.

94
Module : A17-02-05 : General Arrangement Drawing

Assessme
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C01 / 01.04, 01.05, 01.10a, 01.10b

WIM
nt
Learning Experience (LE)
Knowledge Hrs Practical Hrs
LE 2 : PRODUCE PIPING GENERAL ARRANGEMENT DRAWING (GA)
2.1 Prepare hazardous area drawing

2.1.1 Safety principles

 IEC 60079-10-1
 IEC 60079-10-2
2.1.2 Type of hazard
 Gases and Vapours
IS
 Dusts 6 L WT
AS
2.1.3 Area classification
 Explosive atmosphere
 Zone 0
 Zone 1
 Zone 2

2.1.4 Determine safety principles

2.1.5 Determine type of hazard IS
6 P PT
2.1.6 Determine area classification WS

95
Module : A17-02-05 : General Arrangement Drawing

Assessme
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C01 / 01.04, 01.05, 01.10a, 01.10b

WIM
nt
Learning Experience (LE)
Knowledge Hrs Practical Hrs
2.2 Produce Piping General arrangement
drawing (GA)

2.2.1 General arrangement (GA) conceptual

drawing such as:
 Scale
 Dimension
 Elevation
 Tagging
 Line number
 Instrument name

2.2.2 Types of equipment

 Type of location
IS
 Equipment dimension 12 L WT
AS
2.2.3 Types of piping
 Process piping
 Utility piping

2.2.4 CAD software application setting such as:

 Title block setup
 Scale setup
 Dimension setup
 Drawing option
 Tool box icon
 Types of line
 Application command

96
Module : A17-02-05 : General Arrangement Drawing

Assessme
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022:2013-C01 / 01.04, 01.05, 01.10a, 01.10b

WIM
nt
Learning Experience (LE)
Knowledge Hrs Practical Hrs
2.2.5. General arrangement (GA) drawing
 Work instruction
 2D mark-up
 General arrangement (GA) drawing
 Objection view
 Incorporate drawing

2.2.6 Types of plotting

 Setting
 Plot style
 Plot size

2.2.7 Interpret General arrangement (GA)

conceptual drawing
2.2.8 Identify types of equipment.
2.2.9 Identify types of piping.
IS
2.2.10 Apply CAD software 36 P PT
WS
2.2.11 Incorporate General arrangement (GA)
drawing.
2.2.12 Carry out piping plotting drawing.

Total Hours 36 84

97
 Computer, structure general arrangement documents, standard piping and instrument symbols
Tools/ Equipment/ Materials :
(reference) document
1. Mike W.Lin (1993), Drawing and Designing with Confidence: A Step-by-Step Guide,John Wiley &
Sons, Inc., ISBN-978-0471283904
2. Roy A. Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company, Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
Reference Books (Tittle, Atr, Publisher) :
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-Willcox, ISBN 978-15-907-0247-5
7. Dix and Riley, Discovering Auto CAD 2013, Prentice Hall, ISBN 0-132-95856-2
Manuals :

98
5. SEMESTER 3

SEMESTER 2

99
5.1. Carta Profil

SECTOR OIL & GAS

SUB SECTOR OIL, GAS & PETROCHEMICAL
JOB AREA PIPE DRAFTING (OIL & GAS)
NOSS TITLE PIPING DRAFTING (OIL & GAS)
JOB LEVEL THREE (3) JOB AREA CODE

COMPETENCY COMPETENCY UNIT

PIPING MATERIAL PIPING DRAFTING

PIPING DRAWING
TAKE-OFF SUPERVISORY
CORE PRODUCTION
PREPARATION FUNCTION

OG-022-3:2013-C01 OG-022-3:2013-C04 OG-022-3:2013-C05

3D AS-BUILT
ELECTIVE

OG-022-3:2013-E01

PIPING PROJECT
CORE AIDED VALUE

10B

100
 5.2. Carta Aliran Latihan

A17 SIJIL TEKNOLOGI CADD MEKANIKAL ( MINYAK & GAS ) - SEMESTER 3

BERSAMBUNG
DARI
SEMESTER 2

Study scope of work

3D PIPING ISOMETRIC Produce isometric
DESIGN DRAWING piping drawing
06.01 1/4
01.06 1/2
A17 – 03 – 03
A17 – 03 – 01 Prepare 3d as-built
requirements
Submit completed
06.02 2/4 piping drawing for
approval
Perform 3d as-built 01.10 2/2
activities

06.03 3/4

Perform 3d modelling

06.04 4/4
COST Study work instruction
ESTIMATION

04.01 1/4
Incorporate pipe A15 – 03 – 04
PIPE SUPPORT support drawing
DRAWING Prepare working tools
01.07 1/1
requirement
A17 – 03 – 02
04.02 2/4

Perform material take

off on piping drawing

04.04 3/4

Submit completed
C material take off to
superior for
confirmation
04.05 4/4

101
 C

RESOURCE
MANAGEMENT Prepare work schedule

05.02 1/5
A17 – 03 – 05

Carry out job

distribution

05.03 2/5

Monitor work progress

performance
05.04 3/5

Carry out staff coaching

05.06 4/5

Prepare appraisal
recommendation

05.07 5/5

PIPING
PROJECT Prepare Project
Proposals

10B.01 1/3
A17 – 03 – 06

Produce 3D Models
Drawings

10B.02 2/3

Perform presentation

10B.03 3/3
TAMAT

102
 5.3. Carta Perbandingan

A17 – SIJIL TEKNOLOGI CADD MEKANIKAL – SEMESTER 3

COST ESTIMATION
3D PIPING DESIGN

PIPING PROJECT
PIPE SUPPORT

MANAGEMENT
MODULE

RESOURCE
ISOMETRIC
JTM SYLLABUS

DRAWING

DRAWING
TITLE
NOSS (New Format)

A17-03-01

A17-03-02

A17-03-03

A17-03-04

A17-03-05

A17-03-06
NUMBER
CU NO

WA
CU TITLE CU WORK ACTIVITY

Produce Isometric Piping Drawing 0 01.06

PIPING DRAWING
1 Incorporate Pipe Support Drawing 01.07
PRODUCTION
Submit Completed Piping Drawing
01.10
For Approval
Study Work Instruction 04.01
Prepare Working Tools
PIPING MATERIAL 04.02
Requirement
TAKE-OFF
4 Perform Material Take Off On
PREPARATION 04.04
Piping Drawing
Submit Completed Material Take
04.05
off To Superior For Confirmation
Prepare Work Schedule 05.02

Carry Out Job Distribution 05.03

PIPING DRAFTING Monitor Work Progress
5 SUPERVISORY 05.04
Performance
FUNCTION
Carry Out Staff Coaching 05.06
Prepare Appraisal
05.07
Recommendation

Study Scope Of Work 06.01

Prepare 3D As-Built Requirements 06.02

6 3D AS-BUILT
Perform 3D As-Built Activities 06.03

Perform 3D Modelling 06.04

Prepare Project Proposal 10B.01

PERFORM PIPING
10B Produce 3D Models Drawing 10B.02
PROJECT
Perform Presentation 10B.03

103
5.4. Jadual Pembahagian Jam Kredit

A17 SIJIL TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) – SEMESTER 3

JAM KREDIT
TASK
A/(PEMBERAT (1.5) X 20 )
KOD MODUL TAJUK MODUL
JAM JAM JUMLAH
TEORI AMALI KREDIT
KREDIT KREDIT JAM
(JAM) (JAM) MODUL
TEORI AMALI KREDIT
A17-03-01 3D PIPING DESIGN 36 84 1.2 2.8 4.0 4.0
A17-03-02 PIPE SUPPORT DRAWING 18 42 0.6 1.4 2.0 2.0
A17-03-03 ISOMETRIC DRAWING 18 42 0.6 1.4 2.0 2.0
A17-03-04 COST ESTIMATION 18 42 0.6 1.4 2.0 2.0
A17-03-05 RESOURCE MANAGEMENT 27 63 0.9 2.1 3.0 3.0
A17-03-05 PIPING PROJECT 12 108 0.1 3.9 4.0 4.0

JUMLAH LATIHAN ( SUBJEK TERAS ) 129 381 4.0 13.0 17.0 17

PERATUS LATIHAN ( SIJIL ) 25% 75%

MK 2011 MATEMATIK KEJURUTERAAN 2 30 - 1.0 - 1.0 1
SK 2021 SAINS KEJURUTERAAN 2 30 - 1.0 - 1.0 1
PI 2031 / PM 2041 PENDIDIKAN ISLAM 2 / PENDIDIKAN MORAL 2 30 - 1.0 - 1.0 1
JUMLAH LATIHAN ( SUBJEK UMUM ) 90.0 - 3.0 - 3.0 3
JUMLAH KESELURUHAN LATIHAN 600.0 20

104
5.5. Jadual Pengalaman Pembelajaran

JADUAL PENGALAMAN PEMBELAJARAN

A17-03-01 : 3D Piping Design

Terminal Performance Objective:

Carry Out 3D Piping Design using work instruction, permit to work (PTW), personal protective equipment(PPE), surveying
equipment, laser scanner and 3D software so that 3D as-built activities and 3D modelling performed in accordance with company
standard.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Perform 3D as-built activities using work instruction, permit to work (PTW),

personal protective equipment (PPE), laser scanner, surveying equipments, site
LE 1 : PERFORM 3D AS-BUILT ACTIVITIES visit rules and regulation so that work instruction identified, permit to work and
personal protective equipment prepared, site visit rules and regulations
explained and laser scanner operational method applied in accordance with
company standard.

Perform 3D modelling using 3D software, laser scanner database and piping

LE 2 : PERFORM 3D MODELLING
drawing so that 3D modelling produced, database laser scanner registration and
clash check performed in accordance with company standard.

105
 JADUAL PENGALAMAN PEMBELAJARAN

A17-03-02 : Pipe Support Drawing

Terminal Performance Objective:

Perform Pipe Support Drawing using standard piping and instrument symbols (reference) document GA drawing and CAD software
so that Pipe Support Drawing integrated in accordance with company standard and mechanical engineering (oil and gas) drafting
procedure.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Integrate pipe support drawing using standard piping and instrument symbols
(reference) document, GA drawing and CAD software so that types of pipe
LE 1 : INTEGRATE PIPE SUPPORT DRAWING support detail identified and pipe support location plan produced per
specification in accordance with company standard and mechanical
engineering (oil and gas) drafting procedure.

106
 JADUAL PENGALAMAN PEMBELAJARAN

A17-03-01 : Isometric Drawing

Terminal Performance Objective:

Carry Out Isometric Drawing using GA Drawing, P&ID Drawing, piping symbol list, CAD software, material take-off content list and
approved amended drawing so that isometric piping drawing produced in accordance with company standard and mechanical
engineering (oil and gas) drafting procedure.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Produce isometric piping drawing using GA Drawing, P&ID Drawing, piping

symbol list, CAD software, material take-off content list and approved
LE 1 : PRODUCE ISOMETRIC PIPING DRAWING amended drawing so that GA and P&ID drawing interpreted, material take-off
content listed and isometric drawing produced in accordance with company
standard and mechanical engineering (oil and gas) drafting procedure.

107
 JADUAL PENGALAMAN PEMBELAJARAN

A17-03-04 : Cost Estimation

Terminal Performance Objective:

Carry out cost estimation using job description, computer, drawing tools and informations, Material Take Off (MTO) and Bill Of
Material (BOM) format, price list, calculation formula, supplier quotation, appropriate instrument, GA Drawing, P&ID Drawing and
relevant references so that working tools requirements prepared and material take-off performed in accordance with company
standard.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Prepare working tools requirements using job description, piping components,

material specification, drawing symbols, P&ID drawing, GA drawing, material
LE 1 : PREPARE WORKING TOOLS take-off standard form, piping standard reference and computer so that job
REQUIREMENTS description explained, piping components listed, material specification
identified, colour coding listed, and Material Take-Off (MTO) standard form
selected in accordance with company standard.

Perform Material Take - Off using material take-off table , content and data
sheet, software application, computer, drawing tools, drawing informations,
LE 2 : PERFORM MATERIAL TAKE - OFF MTO and BOM format so types of pipe material listed, component quantity
calculated, MTO table format selected, completed MTO checked, confirmed
and updated in accordance with company standard.

108
 JADUAL PENGALAMAN PEMBELAJARAN

A17-03-05 : Resource Management

Terminal Performance Objective:

Perform Resource Management using coaching materials, computer, office equipment, staff performance appraisal form and staff
personel file so that work progress performance monitored and appraisal recommendation prepared in accordance with Skills Matrix
Chart and standard operating procedure.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Monitor work progress performance using office equipment, standard job

sheet, works schedule and computer so that work schedule format, work
LE 1 : MONITOR WORK PROGRESS
resources and capacity identified, lead time estimated, job distribution and
PERFORMANCE
manpower availability arranged in accordance with standard operating
procedure.

Prepare appraisal recommendation using coaching materials, computer,

office equipment, staff performance appraisal form and staff personel file so
that coaching objective explained, staff skills and performance assessed,
LE 2 : PREPARE APPRAISAL RECOMMENDATION
subordinate job description and personnel appraisal evaluation criteria
identified in accordance with Skills Matrix Chart and standard operating
procedure.

109
 JADUAL PENGALAMAN PEMBELAJARAN

A17-03-06 : Piping Project

Terminal Performance Objective:

Develop Piping Project using problem solving technique, standard calculation formula, piping software, Audio Visual Aida (AVA)
and computer so that project proposals prepared and project presentation performed in accordance with project and client
specification.
PENGALAMAN PEMBELAJARAN OBJEKTIF MEMBOLEH
(LEARNING EXPERIENCE) (ENABLING OBJECTIVE)

Prepare project proposal using problem solving technique, standard

calculation formula, piping software and computer so that project proposal
LE 1 : PREPARE PROJECT PROPOSALS
prepared, project analysis conducted and 3D models drawing produced in
accordance with project and client specification.

Perform project presentation using piping software, computer, AVA system

LE 2 : PERFORM PROJECT PRESENTATION and relevant documents so that final project proposals presented in
accordance with project and client specification

110
 5.6. Profil Silibus

SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 36
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 84
Semester : 3 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry Out 3D Piping Design using work instruction, permit to work (PTW), personal protective equipment(PPE), surveying equipment, laser scanner and 3D
software so that 3D as-built activities and 3D modelling performed in accordance with company standard.

Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : PERFORM 3D AS-BUILT ACTIVITIES

111
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2 Study scope work
1.1.1 Work instruction
 Location
 Schedule
 Safety briefing

1.1.2 Piping drawing such as:

 Plot plan layout IS
6 L WT
 Piping General Arrangement (GA) drawing AS
 Equipment layout drawing
 Isometric drawing
 Structure drawing Person in charge in
obtaining client data
 Pipe support drawing

1.1.3 Types of pipe line services such as:

 Instrument air
 Utility air
 Drain
 Process line Client data obtaining
procedure

1.1.4 Existing line pipe such as:

 Line pipe location
 Line pipe number
 Line pipe size

112
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.7 Identify work instruction.

1.1.8 Interpret piping drawing (P&ID) IS

9 P PT WS
1.1.9 Identify types of pipe line service.

1.1.10 Identify existing pipe line.

3.2 Prepare 3D as-built requirements

1.2.2. Specification Types of tools and function such

as :

 Laser scanner (Theodolites) IS

18 L WT
AS
 Total station
 Target (Prism)
 Surveying Rods

113
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

 Surveying Tripod
 Field Books
 Marking Paints / Flagging Markers
 Measuring tapes / Distance Measuring
Wheels

1.2.3. Site visit rules and regulations

 Permit to Work (PTW)

 Personnel protective equipment (PPE)
 Oil and Gas Safety Passport (OGSP)

114
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2.4 Prepare Tools and equipment

 Laser scanner (Theodolites)

 Total station
 Target (Prism)
 Surveying Rods
 Surveying Tripod Field Books
 Marking Paints / Flagging Markers IS
 Measuring tapes / Distance Measuring 27 P PT WS
Wheels

1.2.5 Identify tools function.

1.2.6 Prepare Permit To Work

1.2.7 Prepare Personnel Protective Equipment

(PPE).

115
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.3. Perform 3D as built activities (Surveying)

1.3.1. Laser scanner and function

1.3.2. Laser scanner calibration

1.3.3. Working area

 Replacement target
 Scan location IS
6 L WT
AS
1.3.4. Laser scanner setting
 Low
 Height
 Highest
 Ultra

1.3.5. Laser scanning process handling

1.3.6. Laser scanner operational method

1.3.7. Identify laser scanner function.

1.3.8. Perform laser scanner calibration.
1.3.9. Identify working area.
1.3.10 Set laser scanner. 21 P PT IS
1.3.11 Perform laser scanning handling process. WS
1.3.12 Apply laser scanning operational method

116
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 2 : PERFORM 3D MODELLING
2.1. Obtain client data

2.1.1 3D software application

 Cyclone
 Plant link

2.1.2 Database laser scanner registration

 Required target
 Register IS
6 L WT
AS
2.1.3 Clean up laser scanner database
 Noise

2.1.4 3D modelling application

2.1.5 3D modelling converter application
 Clash check

2.1.6 3D modelling visit report

117
Module : A17-03-01 : 3D Piping Design

Assessmen
t Methods
Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C06 / 06.01, 06.02, 06.03, 06.04

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.8 Apply 3D software application.
2.1.9 Perform database laser scanner registration.
2.1.10 Perform cleaning database laser scanner.
2.1.11 Perform 3D modelling.
IS
2.1.12 Perform clash check.
27 P PT WS
2.1.13 Compile 3D modelling visit report.
2.1.14 Identify responsible personnel.
2.1.15 Submit 3D as-built documentation for
approval.
2.1.16 Amend 3D as-built documentation
Total Hours 36 84

Permit to work (PTW), personal protective equipment(PPE), surveying equipment, laser scanner and
Tools/ Equipment/ Materials :
3D software
1. Mike W.Lin(1993), Drawing and Designing with Confidence: A Step-by-Step Guide, John Wiley &
Sons, Inc., ISBN-978-0471-28390-4
2. Roy A.Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company,Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
Reference Books (Tittle, Atr, Publisher) :
5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-WillcoxISBN 978-15-907-0247-5
7. Dix and Riley, Discovering Auto CAD 2013, Prentice Hall, ISBN 0-132-95856-2
8. George Vosselman, Hans-Gerd Maas, Airborne and Terrestrial Laser Scanning, Whittles Publishing,
ISBN 978-14-398-2798-7
Manuals :

118
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 18
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 42
Semester : 3 Total Credit Hours :2
NOSS Code : OG-022-3
Terminal Performance Objective :
Perform Pipe Support Drawing using standard piping and instrument symbols (reference) document GA drawing and CAD software so that Pipe Support Drawing
integrated in accordance with company standard and mechanical engineering (oil and gas) drafting procedure.

Module : A17-03-02 : Pipe Support Drawing

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C01 / 01.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : INTEGRATE PIPE SUPPORT DRAWING
1.3 Incorporate pipe support drawing

1.1.2 Work instruction

 2D mark-up drawing

1.1.3 Types of pipe support drawing

 Pipe support location plan
 Pipe support details IS
18 L WT
AS
1.1.4 CAD software application setting such as:
 Types of line
 Title block setup
 Scale setup
 Dimension setup
 Drawing option
 Tool box icon

119
Module : A17-03-02 : Pipe Support Drawing

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C01 / 01.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.5 Application command 2D mark-up pipe support
location plan
 Pipe support standard
 Pipe support drawing list number
 Pipe support number
 Structure connection
 Dimensioning
 Plot size

1.1.6 2D mark-up pipe support detail

 Pipe support standard
 Pipe support drawing list
 Pipe support number
 Pipe line number
 Welding symbols
o Field weld
o Shop weld
 Datum
 Dimensioning

1.1.7 Types of plotting

 Setting
 Plot style

120
Module : A17-03-02 : Pipe Support Drawing

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : OG-022-3:2013-C01 / 01.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.8 Identify 2D mark-up drawing.
1.1.9 Identify pipe support drawing.
1.1.10 Identify CAD software.
1.1.11 Incorporate 2D markup pipe support location IS
42 P PT
plan. WS
1.1.12 Incorporate 2D markup pipe support detail.
1.1.13 Carry out plotting drawing.

Total Hours 18 42

Tools/ Equipment/ Materials : Standard piping , instrument symbols (reference) document GA drawing and CAD software
1. Mike W.Lin (1993), Drawing and Designing with Confidence: A Step-by-Step Guide,John Wiley &
Sons, Inc., ISBN-978-0471283904
2. Roy A. Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company, Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
Reference Books (Tittle, Atr, Publisher) :
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-Willcox, ISBN 978-15-907-0247-5
7. Dix and Riley, Discovering Auto CAD 2013, Prentice Hall, ISBN 0-132-95856-2
Manuals :

121
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 18
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 42
Semester : 3 Total Credit Hours :2
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry Out Isometric Drawing using GA Drawing, P&ID Drawing, piping symbol list, CAD software, material take-off content list and approved
amended drawing so that isometric piping drawing produced in accordance with company standard and mechanical engineering (oil and gas)
drafting procedure.

Module : A17-03-03 : Isometric Drawing

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C01 / 01.06, 01.10

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : PRODUCE ISOMETRIC PIPING DRAWING

1.4 Produce isometric piping drawing

1.4.1 Isometric piping drawing IS

 Pipeline selection 9 L WT
AS
 Routing direction
 Isometric view

122
Module : A17-03-03 : Isometric Drawing

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C01 / 01.06, 01.10

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.2 Interpret General Arrangement (GA) and

Piping & Instrument Diagram (P&ID). IS
18 P PT
1.1.3 Produce isometric piping drawing. WS

1.1.4 Material Take-Off (MTO)

 Piping material specification

 Piping components name

 Piping components description

IS
6 L WT
 Piping components size AS

 Piping components classification

 Piping components quantity

1.1.21 Apply incorporate Material Take-Off data IS

18 P PT
WS
1.5 Submit completed piping drawing for approval
IS
1.2.1 2D mark-up drawing 3 L WT
AS
 Changes review area

123
Module : A17-03-03 : Isometric Drawing

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C01 / 01.06, 01.10

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.2.2 Forward piping drawing for approval.

1.2.3 Update 2D mark-up drawing (in any changes). IS
6 P PT
WS

Total Hours 18 42

GA Drawing, P&ID Drawing, piping symbol list, CAD software, material take-off content list and
Tools/ Equipment/ Materials :
approved amended drawing
1. Mike W.Lin (1993), Drawing and Designing with Confidence: A Step-by-Step Guide,John Wiley &
Sons, Inc., ISBN-978-0471283904
2. Roy A. Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company, Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
Reference Books (Tittle, Atr, Publisher) :
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-Willcox, ISBN 978-15-907-0247-5
7. Dix and Riley, Discovering Auto CAD 2013, Prentice Hall, ISBN 0-132-95856-2
Manuals :

124
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 18
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 42
Semester : 3 Total Credit Hours :2
NOSS Code : OG-022-3
Terminal Performance Objective :
Carry out cost estimation using job description, computer, drawing tools and informations, Material Take Off (MTO) and Bill Of Material (BOM)
format, price list, calculation formula, supplier quotation, appropriate instrument, GA Drawing, P&ID Drawing and relevant references so that
working tools requirements prepared and material take-off performed in accordance with company standard.

Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

LE 1 : PREPARE WORKING TOOLS REQUIREMENTS

1.6 Study work instruction

1.6.1 Work scope

 Types of project
 Job description
IS
1.6.2 2D drawing 4.5 L WT
AS
 Piping component items
 Material specification
 Colour coding
 Drawing symbol

125
Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

1.6.3 Piping & instrument diagram drawing

 Process flow

 Drawing symbol

o Components item

o Line symbol

1.6.4 Interpret work scope.

1.6.5 Interpret 2D drawing. IS

9 P PT
WS
1.6.6 Interpret piping & instrument diagram drawing.

126
Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

1.7 Prepare working tools requirements

1.2.1 Types of MTO standard form format

 Softcopy
 Hardcopy
 A4 size

1.2.3 Types of stationary

 Calculator
 Marker pen
IS
 Etc. 4.5 L WT
AS
1.2.4 Piping standard reference
1.2.5 Types of 2D drawing (hardcopy)
 General arrangement (GA) drawing
 Isometrics drawing

1.2.6 Type of 2D piping & instrument diagram drawing

 Softcopy
 Hardcopy

127
Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

1.2.7 Select Material Take - Off (MTO) standard form.

1.2.8 Select stationary.
1.2.9 Select piping standard reference. IS
13.5 P PT
1.2.10 Select 2D hardcopy drawing. WS
1.2.11 Select Piping & instrument diagram.

LE 2: PERFORM MATERIAL TAKE - OFF

2.1 Estimate pipes and components quantity

2.1.1 Types of piping component and function

 Fitting
 Flange
 Gasket
 Stud bolt & Nut
 Gasket
IS
 Valve 4.5 L WT
AS
 Miscellaneous items

2.1.2 Types of pipe materials

 Carbon Steel
 Stainless Steel
 Duplex Stainless steel
 Glass Reinforced Epoxy (GRE)

128
Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

2.1.3 Material specification

 Sizes

 Quantity

2.1.4 Types of piping classification

2.1.5 Calculation method
 Length of pipe

 Dimension

2.1.6 Identify types of piping component.

2.1.7 Identify types of material specification.
2.1.8 Interpret component description.
2.1.9 Interpret component classification. IS
9 P PT
WS
2.1.10 Calculate component quantity
2.1.11 Estimate component size.
2.1.12 Calculate length of pipe.

129
Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

2.2 Perform “Material Take - Off” on piping

drawing

2.2.1 Types of table format

2.2.2 Material Take-Off content
 Components name 3 L WT
IS
AS
 Size
 Quantity
 Classification

2.2.3 Types of office application software

2.2.4 Select “Material Take-Off” table format.
2.2.5 List “Material Take- Off” content.
IS
2.2.6 Apply software application. 6 P PT
WS
2.2.7 Key in “Material Take-Off” data sheet.
2.2.8 Check completed “Material Take-Off”.
2.3 Submit “Material Take Off” to superior for
Confirmation
IS
1.5 L WT
AS
2.3.1 Company’s organization chart
2.3.2 Material Take-Off checklist

130
Module : A17-03-04 : Cost Estimation

Delivery Methods
CoCU / Work Activities No. : OG-022-3:2013-C04 / 04.01, 04.02, 04.04, 04.05

Assessment
Methods
Learning Experience (LE)

WIM
Knowledge Hrs Practical Hrs

2.3.3 Identify responsible personnel.

2.3.4 Forward completed “Material Take-Off” with
recorded data to superior. IS
4.5 P PT
2.3.5 Recalculate “Material Take Off” (if error WS
occurred).
2.3.6 Update “Material Take-Off”.
Total Hours 18 42

Job description, computer, drawing tools and informations, Material Take Off (MTO) and Bill Of
Tools/ Equipment/ Materials : Material (BOM) format, price list, calculation formula, supplier quotation, appropriate instrument, GA
Drawing, P&ID Drawing and relevant references
1. Mike W.Lin(1993), Drawing and Designing with Confidence: A Step-by-Step Guide, John Wiley &
Sons, Inc.,ISBN-978-0471283904
2. Roy A. Parisher 2002, Pipe drafting and design, Gulf Professional Publishing, ISBN 0-7506-7439-3
3. M. W. Kellogg Company, Design Of Piping System, John Wiley & Sons, Inc., ISBN 0-471-46795-2
4. M.B. Shah B.C Rana, Engineering drawing, Pearson Education, ISBN 978-81-317-0944-3
Reference Books (Tittle, Atr, Publisher) : 5. Rip Weaver, Process Piping Drafting, Gulf Publishing Company, ISBN 0-87201-759-5
6. Shumaker, Terence M., Process Pipe Drafting, Goodheart-WillcoxISBN 978-15-907-0247-5
7. Dix and Riley, Discovering Auto CAD 2013, Prentice Hall, ISBN 0-132-95856-2
8. Wayne J, Plan Reading and Material Take Off, R.S. Means Company, ISBN 0-876-29348-8
9. Dickenson T. Christopher, Valves, Piping and Pipelines Handbook, Elsevier Advanced Technology,
ISBN 1-85617-252-X
Manuals :

131
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 27
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 63
Semester : 3 Total Credit Hours :3
NOSS Code : OG-022-3
Terminal Performance Objective :
Perform Resource Management using coaching materials, computer, office equipment, staff performance appraisal form and staff personel file so
that work progress performance monitored and appraisal recommendation prepared in accordance with Skills Matrix Chart and standard operating
procedure.

Module : A17-03-05 : Resource Management

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C05 / 05.02, 05.03, 05.04, 05.06, 05.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

LE 1 : MONITOR WORK PROGRESS PERFORMANCE

1.1 Prepare work schedule

1.1.1 Work schedule format

1.1.2 Master schedule

1.1.3 Types of resources

IS
 Manpower 9 L WT
AS
 Material

 Methods

1.1.4 Company’s target

132
Module : A17-03-05 : Resource Management

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C05 / 05.02, 05.03, 05.04, 05.06, 05.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.1.5 Identify schedule format

1.1.6 Interpret master schedule
1.1.7 Identify Resources availability and capability
IS
1.1.8 Identify Company’s target 18 P PT
WS
1.1.9 Plan drafting schedule
1.1.10 Produce drafting schedule
1.1.11 Submit drafting schedule to superior
1.2 Carry out job distribution

1.2.1 Job distribution form

1.2.2 Work schedule IS
4.5 L WT
 Lead time AS

 Delivery date

1.2.3 Manpower availability

1.2.4 Identify Job distribution form
1.2.5 Estimate lead time IS
10.5 P PT
1.2.6 Confirm delivery date WS
1.2.7 Arrange Manpower availability

133
Module : A17-03-05 : Resource Management

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C05 / 05.02, 05.03, 05.04, 05.06, 05.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

1.3 Monitor work progress performance

IS
1.3.1 Company’s organization chart 4.5 L WT
AS
1.3.2 Job status
1.3.3 Recovery plan
1.3.4 Work progress check sheet format
1.3.5 Coordinate with responsible personnel
1.3.6 Check work status
1.3.7 Arrange recovery plan 10.5 P PT IS
1.3.8 Update work progress check sheet WS
1.3.9 Submit work progress check sheet

LE 2: PREPARE APPRAISAL RECOMMENDATION

2.1 Carry out staff coaching

2.1.1 Coaching objective

2.1.2 Training Need Analysis information IS
4.5 L WT
2.1.3 Skills matrix chart AS
2.1.4 Coaching material
2.1.5 Coaching facilities
2.1.6 Coaching module

134
Module : A17-03-05 : Resource Management

Delivery Methods

Assessment
Methods
CoCU / Work Activities No. : OG-022-3:2013-C05 / 05.02, 05.03, 05.04, 05.06, 05.07

WIM
Learning Experience (LE)

Knowledge Hrs Practical Hrs

2.1.7 Identify coaching objective

2.1.8 Interpret Training Need Analysis information
2.1.9 Interpret skills matrix chart
IS
2.1.10 Prepare coaching material 12 P PT
WS
2.1.11 Prepare coaching facilities
2.1.12 Prepare coaching module
2.1.13 Perform internal staff coaching
2.2 Prepare appraisal recommendation

2.2.1 Personnel appraisal form format IS

4.5 L WT
2.2.2 Subordinate job description AS
2.2.3 Personnel appraisal evaluation criteria
2.2.4 Subordinate performance assessment
2.2.5 Identify personnel format.
2.2.6 Identify subordinate job description.
IS
2.2.7 Identify personnel appraisal evaluation criteria. 12 P PT
WS
2.2.8 Assess subordinate performance.
2.2.9 Forward personnel appraisal form to superior
Total Hours 27 63

135
 Coaching materials, computer, office equipment, staff performance appraisal form and staff personel
Tools/ Equipment/ Materials :
file
1. Lihui Wang (2007), Process Planning and Scheduling for Distributed Manufacturing, Springer, ISBN:
978-1-84-628751-0
2. Alan Dalton (1998), Safety, Health and Environmental Hazards at the Workplace, Cengage
Learning, ISBN:978-0-30-433291-5
Reference Books (Tittle, Atr, Publisher) :
3. Dan Hopwood, Steve Thompson(2006), Workplace safety a guide for small and midsized
companies, John Wiley & Sons Inc., ISBN:978-0-7821-3604-3
4. Gregory T. Haugan, Project Planning and Scheduling, Management Concepts Inc., ISBN 1-56726-
136-1
Manuals :

136
 SYLLABUS PROFILE
Course Code : A17 Knowledge Credit Hours : 12
Course : TEKNOLOGI CADD MEKANIKAL (MINYAK & GAS) Practical Credit Hours : 108
Semester : 3 Total Credit Hours :4
NOSS Code : OG-022-3
Terminal Performance Objective :
Develop Piping Project using problem solving technique, standard calculation formula, piping software and computer so that project proposal
prepared and final presentation performed in accordance with project and client specification.

Module : A17-03-06 : Piping Project

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10B.01, 10B.02, 10B.03

WIM
Learning Experience (LE)
Knowledge Hrs Practical Hrs
LE1 PREPARE PROJECT PROPOSALS

1.1 Discuss project proposals

1.1.1 Introduction
1.1.2 Project duration
1.1.3 Project scope
1.1.4 Research project WT IS
10.5 L
1.1.5 Real model project OT AS
1.1.6 Type of training requirement
1.1.7 Type of training materials
1.1.8 Obtaining training materials

1.2 Produced 2D and 3D Modeling

1.2.1 Prepare project proposals IS
26 P PT
1.2.2 Prepare final project proposals WS

137
Module : A17-03-06 : Piping Project

Assessment
Methods

Methods
Delivery
CoCU / Work Activities No. : 10B.01, 10B.02, 10B.03

WIM
Learning Experience (LE)
Knowledge Hrs Practical Hrs
LE2 PERFORM FINAL PRESENTATION
2.1 Project Presentation
WT IS
2.1.1 Project evaluation 1.5 L
OT AS

2.2 Presentation
2.2.1 Project Report IS
82 P PT
2.2.2 Project Model WS

Total Hours 12 108

Tools/ Equipment/ Materials : Computer, Relevant Drawings, Relevant Document, Stationeries and Models
1. Roy A. Parisher, Robert A. Rhea (2000), Pipe Drafting and Design (2nd Edition), Gulf Professional
Publishing, ISBN 13: 978-0-7506-7439

2. Richard J. Beale, Paul Bowers, Peter Smith (2010), Plant Layout And Construction Design, Gulf
Reference Books (Tittle, Atr, Publisher) : Publishing Company, ISBN-10: 1933762373, ISBN-13: 978-193376237

3. Civil Aviation Authority (UK)(2005), CAP437:Offshore Landing Areas-Guidance on Standards, The

Stationery Office, ISBN : 0-1179-04392-0

Manuals :

138