Scribd
Upload
109 views

Threaded Rod, ASTM A193/A193M and ASME SA193/SA193M, B7, Plain

This document provides product standards for threaded rod according to ASTM A193/A193M and ASME SA193/SA193M, B7 specifications. It lists dimensional requirements including nominal diameters and tolerances, material properties, thread requirements, finishing requirements, marking requirements, and material test reporting requirements. Threaded rods must meet all dimensional, material, and mechanical property specifications to be approved.

Uploaded by

Randy Viola
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
109 views

Threaded Rod, ASTM A193/A193M and ASME SA193/SA193M, B7, Plain

This document provides product standards for threaded rod according to ASTM A193/A193M and ASME SA193/SA193M, B7 specifications. It lists dimensional requirements including nominal diameters and tolerances, material properties, thread requirements, finishing requirements, marking requirements, and material test reporting requirements. Threaded rods must meet all dimensional, material, and mechanical property specifications to be approved.

Uploaded by

Randy Viola
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2 Fastenal Product Standard REV-05

Date: January 12, 2017 TROD.B7.P

Threaded Rod, ASTM A193/A193M and ASME SA193/SA193M, B7, Plain


The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If
the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your
status as an approved vendor. Unless otherwise specified, all referenced consensus standards must be adhered to in their entirety.

Nominal D (Major Diameter)


Diameter
Size
Max. Min.
10-24 * .1900 .1890 .1818
10-32 * .1900 .1891 .1831
1/4-20 .2500 .2489 .2367
1/4-28 .2500 .2490 .2392
5/16-18 .3125 .3113 .2982
5/16-24 .3125 .3114 .3006
3/8-16 .3750 .3737 .3595
3/8-24 .3750 .3739 .3631
7/16-14 .4375 .4361 .4206
7/16-20 .4375 .4362 .4240
1/2-13 .5000 .4985 .4822
1/2-20 .5000 .4987 .4865
9/16-12 .5625 .5609 .5437
9/16-18 .5625 .5611 .5480
5/8-11 .6250 .6233 .6051
5/8-18 .6250 .6236 .6105
3/4-10 .7500 .7482 .7288
3/4-16 .7500 .7485 .7343
7/8-9 .8750 .8731 .8523
7/8-14 .8750 .8734 .8579
Page 2 of 2 Fastenal Product Standard REV-05

Date: January 12, 2017 TROD.B7.P

Nominal D (Major Diameter)


Diameter
Size
Max. Min.
1-8 1.000 .9980 .9755
1-14 * 1.000 .9984 .9881
1 1/8-7 1.125 1.1228 1.0982
1 1/8-8 * 1.125 1.1229 1.1079
1 1/8-12 1.125 1.1232 1.1060
1 1/4-7 1.250 1.2478 1.2232
1 1/4-8 * 1.250 1.2479 1.2329
1 1/4-12 1.250 1.2482 1.2310
1 3/8-6 1.375 1.3726 1.3453
1 3/8-8 * 1.375 1.3728 1.3578
1 3/8-12 1.375 1.3731 1.3559
1 1/2-6 1.500 1.4976 1.4703
1 1/2-8 * 1.500 1.4978 1.4828
1 1/2-12 1.500 1.4981 1.4809
1 5/8-8 * 1.625 1.6228 1.6078
1 5/8-12 1.625 1.6232 1.6118
1 3/4-5 1.750 1.7473 1.7165
1 3/4-8 * 1.750 1.7477 1.7327
1 3/4-12 1.750 1.7482 1.7368
1 7/8-8 * 1.875 1.8727 1.8577
2-4.5 2.000 1.9971 1.9641
2-8 * 2.000 1.9977 1.9827
2-12 2.000 1.9982 1.9868
2 1/4-8 * 2.250 2.2476 2.2326
2 1/2-8 * 2.500 2.4976 2.4826

Length Tolerance
3' +/- 1/4"
6' - 12' +/- 1/2"
Length shall be measured form end to end

Specification Requirements:

• Dimensions: ASME B18.31.3


• Material &
Mechanical Properties: ASTM A193/A193M and ASME SA193/SA193M, B7
• Thread Requirements: Roll threaded to ASME B1.1 UNC, UNF, 8UN and UNS Class 2A
• Finish: Light Protective Oil
• Product Marking: Marked with predetermined color on rod end.
Vendor to supply color code with the MTR and purchase order.
• Material Test Reports: The MTR must have documented lot traceability, dimensional
results, full chemical test results and full mechanical test results
to the specification(s) above. In addition, the MTR shall be in full
compliance with Fastenal’s MTR Requirements.

You might also like