Scribd
Upload
228 views

Interview

The document discusses common mechanical engineering interview questions for design engineers. It provides explanations for questions about geometric dimensioning and tolerancing (GD&T), including who introduced the concept and why it is needed. Additional questions covered include defining a micron, common projection systems used in industry, benefits of GD&T, bolt markings, types of fits, differences between jigs and fixtures, and ways to increase the strength of a bottle.

Uploaded by

Nani
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
228 views

Interview

The document discusses common mechanical engineering interview questions for design engineers. It provides explanations for questions about geometric dimensioning and tolerancing (GD&T), including who introduced the concept and why it is needed. Additional questions covered include defining a micron, common projection systems used in industry, benefits of GD&T, bolt markings, types of fits, differences between jigs and fixtures, and ways to increase the strength of a bottle.

Uploaded by

Nani
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

3/12/2018 Mechanical engineering interview questions for design engineers.

~ MECHANICAL INFO

1) What is GD&T and Who introduced the concept of GD&T?


GD&T is Geometric Dimensioning and Tolerancing .Its a language through which Design
Engineers
communicate.Stanley Parker introduced the concept of Geometric Dimensioning and Tolerancing
(GD&T) in 1930’s and he was from Scotland.

2) What is the need of GD&T?


As we all know that its impossible to get a machine which gives you exact physical parts
according to the required dimension. There is always some sort of deviation in the part
manufactured. The deviations are caused due to following reasons:

1)Vibration in the machine


2)Tool Wear and Tear
3)Friction
4)Mounting Error
5)Human Error
6)Environment conditions.

 So to meet the actual condition of machining tolerances and allowances are provided to the
dimensions. So we require GD&T.

3) What is a micron?
A micron is 1000th part of 1mm. That is divide 1mm into 1000 equal parts the value that you
would get is 1micron. For example the diameter of human hair is approximately 70 to 80
microns.

4) Which Angle of Projection of system is used currently in industry


and why?

http://www.mechanicalinfo.com/2014/11/mechanical-engineering-interview.html 2/7
3/12/2018 Mechanical engineering interview questions for design engineers. ~ MECHANICAL INFO

Currently in industries 1st angle and 3rd angle projection system is used. As of rule we rotate the
horizontal plane clockwise. Now after taking the projection and rotating the horizontal planes we
get perfect individual views in 1st and 3rd angle projection system but in the second and fourth
angle projection system the planes overlap and the views are merged

 The second question to this query would be what if we go against


the rule and rotate the vertical plane clockwise? 
The viewer is on 2nd angle projection and vertical plane is rotated clockwise then top view will be
on bottom of front view and in 4th angle projection the  top view will be on top of front view that
is it will make the same view point as 1st and 3rd angle projection system Depicted in the figure
below so we use only 1st and 3rd angle projection system.

5) What are the benefits of GD & T?


Precision & Accuracy
Reduced rework cost
Reduced Defects
Increased understanding

6) What does 8.8 mark on the bolt signify?


It gives you value of tensile strength and yield strength.
For eg. The tensile strength over here in 8.8 marking bolt would be 800 N/mm^2 and its yield
strength is 640 which is 80% of the tensile strength.

7) Name different types of fits


Clearance fit

http://www.mechanicalinfo.com/2014/11/mechanical-engineering-interview.html 3/7
3/12/2018 Mechanical engineering interview questions for design engineers. ~ MECHANICAL INFO

Interference fit
Transition fit

8) What are jigs and fixture?


this question is often asked and it always confuses. So here is a clear answer for difference
between jigs and fixture.

-Jigs gives direction to cutting tool


-We can perform various operations like drilling, reaming ,tapping and polishing.

-Fixtures are used to hold the workpiece


-Fixture are not used to perform any of the operations

9) If you are provided a bottle then how will you increase its


strength?
The strength depends on design, material and thickness of the part. So in order to increase
strength of the bottle one can provide the ribs and make the bottom of the bottle concave
shaped. You can also increase its strength by using a stronger material and increasing its
thickness.

POSTED IN INDUSTRIAL JOBS, INTERVIEW QUESTION, JOBS ON 17:31 | LEAVE A COMMENT 

Newer Post Home Older Post

0 comments:
Post a Comment

Enter your comment...

Comment as: Select profile...

Publish Preview

Subscribe to: Post Comments (Atom)

http://www.mechanicalinfo.com/2014/11/mechanical-engineering-interview.html 4/7

You might also like