CPE 614
CHAPTER 1
Introduction to
Process Integration
Using Pinch Analysis
What is Pinch Technology?
A systematic technique for the optimal design and retrofit
(improvement) of process systems to achieve maximum
energy and resource efficiency (recovery)
Given
- A set of hot (surplus of heat) process streams (to be
cooled)
- A set of cold (deficit of heat) process streams (to be
heated)
Objective:
- To develop a network of heat recovery to achieve
minimum total cost
Pinch Design Target
Minimum heating requirement (usually steam rate)
Minimum cooling requirement (usually water flow
rate)
Minimum number of units (HE)
Minimum HE Network Area
Basic Concept of Process Design:
Interface of process-utility
Utility serves the process
needs
Supply and demand
Process
relationship exists
between utility and
process
Utility So, DON’T TREAT THE
UTILITY SYSTEM
INDEPENDENTLY!!
The “Onion” Diagram
The diagram that emphasizes the sequential
or hierarchical, nature of process.
ONION DIAGRAM: Exercise
Process modification…
What is better process
integration about?
Better process design
Reduced utility costs
Reduced emissions
Better utilization of capital
Increased throughput in retrofit
Applicability:
Practical
Saves Energy
Saves Emissions
Saves Capital
Applies to New Design and Retrofit
Applies to Continuous and Batch
Applies to All Process Industries
Key concepts of heat exchanger
The heat transfer from one media to another is governed
by several basic rules:
Heat will always be transferred from a hot product to
a cold product
Must always be a temperature difference between the
products
The heat loss by the hot product is equal to the
amount of heat gained by the cold product, except for
energy losses to the surrounding area.
Heat Exchanger Schematic
Shell and Tube Heat Exchanger
• Common HE used in chemical process industries for heat
economy.
• Many tubes go from a header on one side to a header on the
other. The other fluid is in the space outside the tubes.
• Hot streams exchange energy with colder streams so that the
thermal energy of the hot streams is not wasted.
Heat Exchanger Schematic
Counter-current heat Co-current/ Parallel Flow
exchanger Heat Exchanger
Tai Tai
Tbo Tbi Tbo Tbi
Tao Tao
Fluids flow in opposite Fluids flow in the same
directions. direction.
Heat Exchanger Network:
Basic
Stream that needs cooling → “ hot stream” (heat source)
Tin = 2000C Tout= 500C
Cooling water is use for cooling
Stream that needs heating → “cold stream” (heat sink)
Tout = 1300C Tin = 400C
Steam is use for heating
How Much Heating Is Needed?
A cold stream (that needs heating)
Ttarget= 1300C
Tsupply = 400C A Heater-Use Medium
Pressure Steam
Given: Heat Capacity Flowrate, FCp (MW/K) = 2.0
Determine Enthalpy Change ΔH (MW)= FCpΔT
How Much Cooling Is Needed?
A Hot stream (that needs cooling)
Ttarget= 500C
Tsupply = 2000C
A Cooler-Use Medium
Cooling Water
Given: Heat Capacity Flowrate, FCp (MW/K) = 1.0
Determine Enthalpy Change ΔH (MW).
Exercise: Heat Exchange between
Process Streams
Stream Stream Tsupply (0C) Ttarget (0C) FCp = CP ΔH (MW)
Number Type (MW/K)
1 Cold 40 130 2.0
2 Hot 200 50 1.0
Before Integration After Integration
A process to process
heat exchanger
Temperature-Enthalpy Diagram
• Temperature-Enthalpy diagrams can be used to determine heat
recovery potential
EXAMPLE :
A simple flowsheet with ONE hot stream and ONE cold stream
Stream Type Supply Target ∆H
Temp. Temp. (MW)
(oC) (oC)
1 Cold 40 110 14
2 Hot 160 40 -12
ΔTmin
"Minimum Permissible Temperature
Difference"
ΔTmin = 20OC
Which Exchanger Violates ΔTmin?
CPE 614
CHAPTER 2
SETTING THE
PROCESS ENERGY
TARGETS
Process Energy Targets
Process energy targets (minimum steam and cooling
water requirements) can be obtained from:
Composite Curves
Cumulative process heat availability (surplus)
Cumulative process heat requirement (deficit)
Problem Table Analysis
Process heat surpluses and deficits within some
specified temperature intervals
A simple flowsheet with two hot streams
and two cold streams
Process Energy Targets:
Composite Curves
Representation of process streams ‘heat content on a
plot of temperature (T) versus enthalpy (ΔH)’
Procedure for Composite Curves:
1. Calculate unknown value (ΔH or CP value)
2. Plot T – H diagram for hot stream
3. Composite T – H diagram for hot stream and
determine new CP value
4. Calculate new ΔH for QC,min, Qrecovery and QH,min
5. Repeat step 2 – 4 for cold stream
6. Plot hot and cold stream together
7. Pinch point: vertical distance between hot CC and
cold CC = ΔTmin
Example 1
Determine the energy target through Composite
Curve by given ∆Tmin = 10◦C.
Stream Type Supply Temp. Target Temp. ∆H (kW)
Ts (oC) TT (oC)
Reactor 1 Cold 20 180 3200
Feed
Reactor 1 Hot 250 40 -3150
Product
Reactor 2 Cold 140 230 2700
Feed
Reactor 2 Hot 200 80 -3000
Product
Solution:
Effect of ΔTmin
ΔTmin = the smallest approach temperature (ΔT) for
heat exchange
Bigger ΔTmin gives:
Less heat recovery
Maximum hot and cold utilities
Maximum energy consumption
Big capital cost
Small ΔTmin gives:
Maximize energy recovery
Minimize hot and cold utilities
Minimize energy consumption
BUT, there are problems with the CC!!!
1) Complicated
2) Difficult to get accurate point for Pinch
temperature, QHmin and Qcmin
An Alternative:
the “PROBLEM TABLE ANALYSIS”
Process Energy Targets:
Problem Table Analysis
2 Approaches:
Hot and Cold Temperature Intervals
Global (Shifted) Temperature Intervals
Cold Stream +∆Tmin /2
Hot Stream -∆Tmin /2
General Idea
Get net ΔH for each heat/enthalpy interval
∑ΔHHOT - ∑ΔHCOLD = (∑FCpHOT -∑FCpCOLD) ΔT
Cascade ΔHnet downwards for cumulative net ΔH
Only cascade for positive heat flow – eliminate
negative heat flow
Procedure for Problem Table Analysis:
1. Determine Interval Temperature Table
2. Draw shifted temperature intervals
3. Calculate Interval Heat Balance,
4. Cascade any surplus heat from high to low
temperature
5. Cascade for positive heat flows
6. Pinch point: Heat = 0 kW
Example 2
Determine the energy target through Problem Table
Analysis by given ∆Tmin = 10◦C .
Stream Type Supply Target ∆H (kW) Heat
Temp. Temp. Capacity
Ts (oC) TT (oC) Flowrate,
CP (kW
oC-1)
Reactor 1 Cold 20 180 3200 20
Feed
Reactor 1 Hot 250 40 -3150 15
Product
Reactor 2 Cold 140 230 2700 30
Feed
Reactor 2 Hot 200 80 -3000 25
Product
Solution:
