American Journal of Engineering Research (AJER) 2017

American Journal of Engineering Research (AJER)

e-ISSN: 2320-0847 p-ISSN : 2320-0936
Volume-6, Issue-11, pp-128-134
www.ajer.org
Research Paper Open Access

Study of Continuity Analysis in INTZE Type Tank using

Conventional and Finite Element Method
Dhruv Saxena1
1
M.E., M.B.M. Engineering, JNV University Jodhpur, Rajasthan, India
1
B.Tech., National Institute of Technology, Silchar, Assam, India
1
[email protected]

Abstract: In this study only Intze type tank is considered, because in the present scenario of fast and large
scale infrastructure development, most of water tanks are constructed of large to medium capacity having heavy
load on bottom dome and its diameter is large, the ring beam needs large amount of reinforcement. It becomes
more economical to reduce its diameter by introducing a conical dome to reduce the ring tension. The bottom
ring beam in Intze tank required much lighter reinforcement as the thrust from the conical dome opposes the
force from the bottom dome, hence Intze tank is economical. This study is carried out to know the importance of
continuity analysis for practical consideration. In this study analysis of Intze type container of water tank is
carried out by both methods by using conventional method and finite element method. In conventional method,
the analysis of Intze type tank carried out in two parts as under,
1) Considering only membrane forces, and
2) Considering effect of continuity along with membrane forces.
The finite element modelling and analysis are done by using of STAAD Pro Software. Two different capacity
tanks were analysed by all three methods and with different ratios of height of the conical shell to height of the
cylindrical shell.
Keywords: Intze type tank, Continuity analysis, membrane analysis, Finite Element method, STAAD PRO.
----------------------------------------------------------------------------------------------------------------------------- ----------
Date of Submission: 03-11-2017 Date of acceptance: 17-11-2017
---------------------------------------------------------------------------------------------------------------- -----------------------

I. INTRODUCTION
Generally water tanks are analysed and designed for membrane stresses only, because of small flexural
rigidity, bending moment at supports are very small. In the big capacity of tank, at the joint of different elements
the secondary stresses are developing due to effect of continuity. In the big capacity of tank, the Intze type
container tank will be economical.
In the design of normal building structures, the most critical aspect of the design is to ensure that the
structure retains its stability under the imposed loads. In the design of water retaining structures to retain water,
it is usually found that, if the structure has been proportioned and reinforced so that the water is retained without
leakage, then the strength is more than adequate.
A 15 lacs litres capacity tank is analysed by all the three methods, i.e. by membrane theory,
considering effect of continuity along with membrane forces and finite element method’s results were compared.
The applicability of conventional method, considering effect of continuity was finalized after comparing results
of conventional method with the finite element method.
Another 25 lacs litres capacity tank is analysed by all the three methods, i.e. by membrane theory,
considering effect of continuity along with membrane forces and by finite element method and results were
compared of both tanks.
It is seen that, the percentage effect of continuity is same and does not differ with respect to the capacity of tank.
Capacity of tank is taken as 15 lacs litres.
Angle of inclination of conical wall is taken as 450
The diameter of bottom dome is taken as 13.00 m.

www.ajer.org Page 128

American Journal of Engineering Research (AJER) 2017

Fig. 1

II. LITERATURE
Shell structure
By virtue of its geometry a shell structure carries the applied load primarily by direct stresses lying in
its plane. Because of small flexure rigidity, bending moment at supports is very small & usually neglected.
The Intze container consist of four shells, one conical shell and one cylindrical shell, and covered at top
and bottom by spherical shell of dome. All these four shells are surfaces of revolution. Since the loads and
forces on each shell are symmetrical about the axis of revolution, it is possible to support/carry these load
mainly this loads by the development of membrane stresses in different shells, that is, only direct stresses will be
created in each shell if its supports did not restrain its edge displacements. Bending and normal shear stresses
will then be almost absent. These direct stresses are the meridional and hoop stresses.
Since supports restrain edge displacements, because of small flexural rigidity bending moments
developed are very small and usually neglected. That is effect of continuity at joints of different elements is not
usually not considered and shell elements are designed for membrane stresses only. (Chandrashekhar)

Objective of Study
1. The main objective of this study is to understand the difference in results of membrane analysis and analysis
with effect of continuity.
2. It will help to designer to decide, whether analysis with effect of continuity is required or not.
3. Another objective is to study of results of analysis by finite element method.

Scope of Work
1. Analysis and Design of Intze type container by membrane analysis.
2. Analysis and Design of Intze type container with effect of continuity by conventional method.
3. Comparison of the results of membrane analysis and continuity analysis by conventional method.
4. Analysis of Intze type container using Finite Element method.
5. Comparison of the results of analysis by conventional method and Finite Element method.

Fig.2 Deflected Shape of INTZE Container

Rotation of Joints Due to Effect of Continuity

The angle at corner A & C tends to close resulting in sagging moment, while the angle at B tends to
increase resulting in hogging moments. Also, the edges of top dome and vertical wall at A are pulled outwards
resulting in tensile hoop stresses, while the ring beam A is pushed inward and its hoop tension is reduced.
Similarly the beam C and edges of conical dome at C are pushed inwards causing a reduction in hoop tension.
At joint B, the conical wall is pushed in-wards, the bottom dome and beam B are pulled outwards. This causes a
hoop compression in beam B and bottom dome. (O.P. Jain, 1987)

www.ajer.org Page 129

American Journal of Engineering Research (AJER) 2017
FINITE ELEMENT METHOD
Introduction and Principal of FEM
In last three decades there has been a great expansion and development and availability of numerical
procedures. It is not possible to obtained analytical mathematical solutions for many engineering problems. This
has opened a new era in analysis and design for complex problems. Most of the available techniques are based
on the principle of discretization. In this a complex problem is divided into smaller equivalent units. In finite
element methods the continuum is considered as an assemblage of the 'finite elements'. The finite element
method is based upon the general principal known as “going from part to whole.”
Finite element analysis is the extension of techniques of analysis of one-dimensional structure into two-
dimensional structures such as plates and shells and equally applicable to three-dimensional structures as well.
In a continuum, which is divided into a mesh, two adjacent elements placed side by side will have a
common edge. As it adds to complication, to make analysis simpler the elements are assumed to be connected at
nodal points only.
Once discretization is made, the analysis follows a set of procedure. The stiffness matrix of individual
element is formulated. The forces actually distributed in real structure are transformed to act at the nodal points.
Total structure obtained as an assembly of individual element is analysed similar to one-dimensional structure.
In finite element analysis a continuum is divided into a finite numbers of elements, having 'finite'
dimension and reducing the continuum having infinite degrees of freedom to finite degrees of unknown. The
accuracy increases with numbers of elements taken. The selection of mesh size and numbers of elements
depends on past experiences and the trial & error method. In the region where stress concentration is high, finer
division should be made.
In FEM, the physical body approximated by replacing it with an assemblage of discrete elements and
these elements can be put together in number of ways. As a result FEM is preferred by engineers and scientists.
(Abel, 1987)

III. ANALYSIS OF INTZE TYPE CONTAINER

By Conventional Method
Intze type container of water tank is analysed and designed by using conventional method, in two parts-
1. Considering only membrane forces.
2. Considering effect of continuity along with membrane forces.

By Finite Element Method (Using Staad Pro.)

Staad Pro. Software is used for modelling and analysis.
The nodes are inserted as per requirements of numbers and types of elements for model. Considered 2-D (two
dimensional), quadrilateral element problem as shown in fig 1.

Fig.3 Two Dimensional Quadrilateral Element

Prepared 2-D elements by connecting nodes, and properties given as plate thickness.
Only D.L and Water loads are considered. As only container is analysed Wind load and/or Seismic load are not
considered.
Loads are given as element load.
Given support condition as Fixed but releasing Fx, Fz, Mx and Mz, we can also give support condition as Fixed
but releasing Fx, Fz, Mx, My and Mz, except one support must be pinned.
Two tanks are analyzed for different capacities as 15 lacs litres and 25 lacs litres.

www.ajer.org Page 130

American Journal of Engineering Research (AJER) 2017
Staad Pro

Fig 3. Staad Model

Fig 4. Plate number of different Component

Hoop Force Calculation

Height of cylindrical wall H = 3.400 m
Height of conical portion h1 = 4.067 m
Total height h = 7.467 m
Radius at cylindrical wall R = 9.500 m
Radius at conical shell = 7.417 m
at mid ht Rav=
Unit weight of water = 1.000 T/m3
2
Hoop force in cylindrical shell=0.5wH R = 54.91 T
Hoop force in conical shell= wHavhRav = 163.901 T
Total hoop force = 218.811 T
Variation with staad result = 0.019 %
Table 1: Hoop Force Calculation

Fig 5. Dimensional Geometry of Container

www.ajer.org Page 131

American Journal of Engineering Research (AJER) 2017
Stress Diagram
Top Dome
Sign convention: -ve shows compression & +ve shows tension

Fig 6. Stress Diagram of Top Dome

Observations:
 Near joint of top ring beam the tension is observed in dome due to continuity effect.
 The value of tensile stresses is varying from 0.495 N/mm2 to 0.081 N/mm2.
 This requires the reinforcement of 330 mm2 to 54 mm2.
 We have generally provided 8mm# @ 200 mm, which is 250 mm2.
 It is necessary to provide 8mm# @ 150 mm c/c up to 1.30 m, which is 0.15m length.
 This requirement is fulfilled by extending the outside reinforcement of cylindrical shell up to required
length, inside top dome.

Cylindrical Shell

Figure 7. Stress Diagram of Cylindrical shell

Observations:
 Whole cylindrical wall is under tension.
 It is observed that tension is increased with respect to depth.

www.ajer.org Page 132

American Journal of Engineering Research (AJER) 2017
Conical Shell

Fig 8. Stress Diagram of Conical shell

Observations:
 Most of conical shell is under tension except bottom edge.

Bottom Dome

Figure 9. Stress Diagram of Bottom Dome

Observations:
 Whole bottom dome is under compression.
Similarly, Staad Model of 25.0 lacs litres tank can also be analysed

IV. COMPARISON OF RESULTS

Comparison of Beam Forces
Axial Force in kN
Member Location Membrane With Continuity FEM
1177 Top ring beam -184 -77 -80
1213 Middle ring beam -827 -650 -628
1251 Bottom ring beam 47 26 20
Table 2: Beam Forces of 15 lacs litres
Negative = tension
Positive = compression

Comparison of Plate Stresses

Stress in N/mm2
Plate Location Membrane With Continuity FEM

1136 Top Dome @ Top ring -0.250 0.480 0.495

www.ajer.org Page 133

American Journal of Engineering Research (AJER) 2017
beam
1135 Vertical Wall @ Top 0.094 0.480 0.477
1132 Vertical Wall @ Bbottom 0.408 1.389 1.330
1131 Conical Wall @ Top 1.253 1.389 1.300
1126 Conical Wall @ Bottom 1.104 -0.108 -0.435
1125 Bottom dome @ Bottom -2.400 -0.104 -0.435
Table 3: Plate Stresses of 15 Lacs Litres

Comparison of Design Requirements

Member Location Member Size Membrane Continuity
Analysis Analysis

Joint A (Near Top Ring Beam)

Top Dome Near top ring beam 100mm thick 8mm @ 200mm c/c 8mm @ 150mm c/c
both ways required
Top Ring Beam 400 x 400 7 Nos – 16mm dia 5 Nos – 12mm dia
Vert-wall Near ring beam 100mm thick 10mm @ 270mm 10mm @ 250mm
c/c both face c/c required

Joint C (near Middle Ring Beam)

Vert-Wall Near middle ring 180mm thick 12mm @ 260mm 12mm @ 130mm
beam c/c both face c/c both face
Middle Ring Beam 780 x 600 18 nos – 20mm dia 14 Nos – 20mm dia
Coni-Wall Near middle ring 400mm thick 20mm @ 145mm 20mm @ 165mm
beam c/c both face c/c both face

Joint B (Near Bottom Ring Beam)

Coni-Wall Near bottom ring 550mm thick 20mm @ 135mm 12mm @ 170mm
beam c/c both face c/c both face
Bottom Ring Beam in 380 x 200 8 Nos – 16mm dia 8 Nos – 16mm dia
Compression
200mm thick 360mm thick
Bottom Dome Near bottom ring 8mm @220mm c/c 10mm @ 100mm
beam both ways c/c
Table 4: Design Requirements for Both the methods.

REFERENCES
[1] A.P.Gupta, S. &. Reinforced Concrete. Oxford & IBH Publishing Co.
[2] Abel, C. S. (1987). Introduction to Finate Element Method. New York , Ithala: CBS Publishers.
[3] Anchor, R. D. Design of Liquid Retaining Concrete. London: Edward Arnold.
[4] B.C.Punamia. Design of RCC Structures.
[5] Chandrashekhar. Theory of Thin Shell.
[6] India, T. s. Design of water retaining structure. Tor steel research foundation in India.
[7] IS 3370.
[8] IS: 3370 (Part I, I. &. (1965). Code for Practice for Concrete Structures for the Storage of Liquids. New Delhi: Indian Standard
Institution.
[9] O.P.Jain, J. K. (1987). Plain and Reinforced Concrete (Vol II). Roorkee: Nem Chand & Bros.
[10] P.Dayaratnam. (1983). Design of Reinforced Concrete Structures. Kanpur: Oxford & IBH Publishing Co.
[11] R.D., A. (1992, second edition). Design of Liquid Retaining Concrete Structures. London Melbourne: Edward Anchor.

Dhruv Saxena Study of Continuity Analysis in INTZE Type Tank using Conventional and
Finite Element Method.” American Journal of Engineering Research (AJER), vol. 6, no. 11,
2017, pp. 128-134.

www.ajer.org Page 134