W

CIRCUIT DRAWN WITH POWER SUPPLY OFF FOR TYPICAL REMOTE CONTROL
M 2
2 DETAILS, SEE DOCUMENT
3
3 V
4
1
3
PHASE
RWS101
SUPPLY
U
3 1 TR AN S F OR ME R TAP P IN G OP TION S
6

5 T ap Nominal 50/60Hz
U V W E TYP E 1
FS1
W 220/230
X 380/400
C1 C2 Y 400,415/420
U W X Y Z
Z 440/460
F US E F S 1= 250mA A NTI-S UR G E
SK2 TYP E 2
0VAC 1 4 W 346/380
TRANSISTOR SWITCHING FOR 120VAC
PS1 X 480/500
24VDC CONTACTORS (IQ10-35) 120VAC 4 5 NOMINAL SUPPLY
RELAYS ONLY FITTED WHEN (OUTPUT) Y 240/240
0VDC
120VAC CONTACTOR IS FITTED 3 Z 550/575
FOR IQ40,70,90,91 & 95 24VDC 6 F US E F S 1= 250mA A NTI-S UR G E
_

+
TYP E 3
SK14
X 660/660-690
0VDC 1
Y 690/-
24VDC 2 F US E F S 1= 150mA A NTI-S UR G E
SK13

26 WAY
REFER TO SHEET 2 FOR NOTES
& OPTION PCB'S IF FITTED

SK3 SK13 SK14

6 1 42
MONITOR RELAY
5 3 43
TORQUE 4 2 44
3
2
SK7
SENSOR 1 1 6
SK8 MAKE AT FULLY SHUT S1 8 7
POSITION 10 WAY 2 8
SENSOR MAKE AT FULLY OPEN S2 7 9
SK9 BREAK AT FULLY SHUT
3 10
BATTERY - 4
S3 6 11
4 12
+
1 BREAK AT FULLY OPEN S4 5 13
FS2 (IF FITTED) 100mA SK4
CLOSE 9 33
STOP/ MAINTAIN 10 34
50% SK6 OPEN 8 35
COMMON -VE 1 36
18 WAY
REMOTE
ESD 12 25
CLOSED
STOP

OPEN LOCAL
OPEN INTERLOCK 13 37
CLOSE INTERLOCK 14 38
COMMON -VE 5 31
SK1 SK2
SLOT A SLOT B

Iss Date Chkd Revision Details IQ + 120VAC REMOTE CONTROL SUPPLY.

5 090113 PMJ Re-track of the 24V DC pin
on SK14 to behind the
www. .com
diode. ROTORK CONTROLS LTD ROTORK CONTROLS INC Drawn by: PMJ Circuit Diagram Number Issue Sheet
6 170413 JHW RWS WAS 100 BATH, BA1 3JQ ROCHESTER Date : 160512 No

7 180614 MR 400v added to type 1

tapping Y. Note added to
ENGLAND NY 14624, USA
Base WD: 110B0000
Job No : - -
110B0000 7
1
of 2
sheet 2 note 1. Tel:01225-733200 Tel:585-247-2304 MI No : - - B1 C1 B2 C2
IQ3
 CIRCUIT DRAWN WITH POWER SUPPLY OFF

NO
OPTIONS
FITTED

NOTES
1.FUSES: 3.INDICATION:
-PS1 is a self-resetting fuse. -For typical position, status and alarm indication see PUB002-041.
-Refer to publication PUB002-039 for approved fuses FS1 and FS2. -“S” contacts are user configurable and are shown in their default
-Actuator rated voltage specified on nameplate. Voltage tolerance +/-10%, setting.
applies for rated torque performance; duty cycle is not guaranteed. -Refer to PUB002-040 for functions and configuration instructions.
2.REMOTE CONTROL: -Monitor Relay indicates actuator availability for remote control (shown
-For typical remote control circuits refer to: “unavailable”). It can be configured to exclude local/remote selection.
-RWS indicated or PUB002-041. -Refer to PUB002-040 for monitored functions and configuration
-For DC and AC control, connect –ve/0V to terminal 36. instructions.
-(For negative switch / positive common, refer to RWS indicated). -Voltage applied to indication contacts must not exceed 150Vac
-Control signal threshold voltages: -Individual Switch current must not exceed 3.5A inductive, 5A resistive
-DC: “on” ≥16Vdc / “off” ≤8Vdc, max 60Vdc. and no more than 8A in total for all 4 contacts.
-AC: “on” ≥60Vac / “off” ≤40Vac, max 120Vac.
-Control signal duration to be 300ms minimum. 4.BATTERY:
-Maximum current drawn from remote control signals is: -Battery maintains local and remote “S” contact indication only.
-8mA at 24Vdc or 12mA at 120Vac. -Refer to installation manual for approved replacement battery types.
-Supply provided on terminals 4 & 5:
-Intended for remote control. Circuit Diagram Number Issue Sheet
-Max external load 5W at 24Vdc / 5VA at 120Vac No
110B0000 7 2
See Sheet 1 for all Revision details/information of 2
IQ3