Cisco IOS ISO CLNS Command Reference

Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.;
Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE,
CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems
logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ
Net Readiness Scorecard, LightStream, MGX, MICA, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX,
Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO
are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.

All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0304R)

Cisco IOS ISO CLNS Command Reference

Copyright © 2002-2003, Cisco Systems, Inc.
All rights reserved.
 CONTENTS

Introduction P5R-1

Cisco IOS ISO CLNS Commands P5R-2

Cisco IOS ISO CLNS Command Reference

iii
Contents

Cisco IOS ISO CLNS Command Reference

iv
Introduction

The International Organization for Standardization (ISO) Connectionless Network Service (CLNS)
protocol is a standard for the network layer of the OSI model.
Use the commands in this book to configure and monitor ISO CLNS networks. For ISO CLNS protocol
configuration information and examples, refer to the “Configuring ISO CLNS” chapter of the Cisco IOS
Apollo Domain, Banyan VINES, DECnet, ISO CLNS, and XNS Configuration Guide.

Cisco IOS ISO CLNS Command Reference

P5R-1
Cisco IOS ISO CLNS Commands

Cisco IOS ISO CLNS Command Reference

P5R-2
 Cisco IOS ISO CLNS Commands
clear clns cache

clear clns cache

To clear and reinitialize the CLNS routing cache, use the clear clns cache command in EXEC mode.

clear clns cache

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following example clears the CLNS routing cache:

clear clns cache

Related Commands Command Description

show clns cache Displays the CLNS routing cache.

Cisco IOS ISO CLNS Command Reference

P5R-3
 Cisco IOS ISO CLNS Commands
clear clns es-neighbors

clear clns es-neighbors

To remove end system (ES) neighbor information from the adjacency database, use the clear clns
es-neighbors command in EXEC mode.

clear clns [tag] es-neighbors

Syntax Description tag (Optional) Meaningful name for a routing process. For example, you could
define a routing process named Finance for the Finance department, and
another routing process named Marketing for the Marketing department. If
not specified, a null tag is assumed. The tag argument must be unique among
all CLNS router processes for a given router.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.
12.0(5)T The tag argument was added.

Usage Guidelines When you enter the clear clns es-neighbors command to clear dynamically discovered neighbors that
are learned through ES-IS or IS-IS protocols, keep in mind that these adjacencies may have reappeared
by the time you enter the show clns neighbors command. These dynamic adjacencies can be quickly
reformed if the neighbors exchange hello messages.

Examples The following example removes the ES neighbor information from the adjacency database:
clear clns es-neighbors

Related Commands Command Description

clear clns is-neighbors Removes the IS neighbors that this router knows.
clear clns neighbors Removes CLNS neighbor information from the adjacency database.
show clns es-neighbors Lists the ES neighbors that this router knows.

Cisco IOS ISO CLNS Command Reference

P5R-4
 Cisco IOS ISO CLNS Commands
clear clns is-neighbors

clear clns is-neighbors

To remove intermediate system (IS) neighbor information from the adjacency database, use the clear
clns is-neighbors command in EXEC mode.

clear clns [tag] is-neighbors

Syntax Description tag (Optional) Meaningful name for a routing process. For example, you could
define a routing process named Finance for the Finance department, and
another routing process named Marketing for the Marketing department. If
not specified, a null tag is assumed. The tag argument must be unique among
all CLNS router processes for a given router.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.
12.0(5)T The tag argument was added.

Usage Guidelines When you enter the clear clns is-neighbors command to clear dynamically discovered neighbors that
are learned through ES-IS or IS-IS protocols, keep in mind that these adjacencies may have reappeared
by the time you enter the show clns neighbors command. These dynamic adjacencies can be quickly
reformed if the neighbors exchange hello messages.

Examples The following example removes the IS neighbor information from the adjacency database:
clear clns is-neighbors

Related Commands Command Description

clear clns es-neighbors Removes ES neighbor information from the adjacency database.
clear clns neighbors Removes CLNS neighbor information from the adjacency database.
show clns is-neighbors Displays IS-IS related information for IS-IS router adjacencies.

Cisco IOS ISO CLNS Command Reference

P5R-5
 Cisco IOS ISO CLNS Commands
clear clns neighbors

clear clns neighbors

To remove CLNS neighbor information from the adjacency database, use the clear clns neighbors
command in EXEC mode.

clear clns [tag] neighbors

Syntax Description tag (Optional) Meaningful name for a routing process. For example, you could
define a routing process named Finance for the Finance department, and
another routing process named Marketing for the Marketing department. If
not specified, a null tag is assumed. The tag argument must be unique among
all CLNS router processes for a given router.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.
12.0(5)T The tag argument was added.

Usage Guidelines When you enter the clear clns neighbors command to clear dynamically discovered neighbors that are
learned through ES-IS or IS-IS protocols, keep in mind that these adjacencies may have reappeared by
the time you enter the show clns neighbors command. These dynamic adjacencies can be quickly
reformed if the neighbors exchange hello messages.

Examples The following example removes the CLNS neighbor information from the adjacency database:
clear clns neighbors

Related Commands Command Description

clear clns es-neighbors Removes ES neighbor information from the adjacency database.
clear clns is-neighbors Removes IS neighbor information from the adjacency database.
show clns neighbors Displays both ES and IS neighbors.

Cisco IOS ISO CLNS Command Reference

P5R-6
 Cisco IOS ISO CLNS Commands
clear clns route

clear clns route

To remove all of the dynamically derived CLNS routing information, use the clear clns route command
in EXEC mode.

clear clns route

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following example removes all of the dynamically derived CLNS routing information:
clear clns route

Related Commands Command Description

show clns route Displays all of the destinations to which this router knows how to route
packets.

Cisco IOS ISO CLNS Command Reference

P5R-7
 Cisco IOS ISO CLNS Commands
clear clns traffic

clear clns traffic

To clear all ISO CLNS statistics that are displayed when you use the show clns traffic command, use
the clear clns traffic command in EXEC mode.

clear clns [tag] traffic

Syntax Description tag (Optional) Meaningful name for a routing process. For example, you could
define a routing process named Finance for the Finance department, and
another routing process named Marketing for the Marketing department. If
not specified, a null tag is assumed. The tag argument must be unique among
all CLNS router processes for a given router.

Command Modes EXEC

Command History Release Modification

12.1 This command was introduced.

Examples The following example removes the ISO CLNS statistics:

clear clns traffic

Related Commands Command Description

show clns traffic Lists the CLNS packets that this router has seen.

Cisco IOS ISO CLNS Command Reference

P5R-8
 Cisco IOS ISO CLNS Commands
clear tarp counters

clear tarp counters

To clear all Target Identifier Address Resolution Protocol (TARP) counters that are shown with the show
tarp traffic command, use the clear tarp counters command in EXEC mode.

clear tarp counters

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Clearing the counters can assist you with troubleshooting. For example, you may want to clear the
counter and then check to see how many PDUs the router is originating.

Examples The following example clears the TARP counters:

clear tarp counters

Related Commands Command Description

show tarp traffic Displays statistics about TARP PDUs since the last time the counters were
cleared.

Cisco IOS ISO CLNS Command Reference

P5R-9
 Cisco IOS ISO CLNS Commands
clear tarp ldb-table

clear tarp ldb-table

To clear the system ID-to-sequence number mapping entries stored in the TARP loop-detection buffer
table, use the clear tarp ldb-table command in EXEC mode.

clear tarp ldb-table

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines The loop-detection buffer table prevents TARP packets from looping.
Clearing the mapping entries assists you with troubleshooting. For example, clear the loop-detection
buffer table and assign a new sequence number (using the tarp sequence-number command) to ensure
that other hosts update their entries.

Examples The following example clears the TARP loop-detection buffer table:
clear tarp ldb-table

Related Commands Command Description

show tarp ldb Displays the contents of the loop-detection buffer table.
tarp ldb-timer Specifies the length of time that a system ID-to-sequence number mapping
entry remains in the loop-detection buffer table.

Cisco IOS ISO CLNS Command Reference

P5R-10
 Cisco IOS ISO CLNS Commands
clear tarp tid-table

clear tarp tid-table

To clear the dynamically created TARP target identifier (TID)-to-NSAP address mapping entries stored
in TID cache, use the clear tarp tid-table command in EXEC mode.

clear tarp tid-table

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Clearing the TID cache is one method to remove old entries. Another method is to set the length of time
a dynamically created TARP entry remains in the TID cache using the tarp cache-timer command.
The clear tarp tid-table command does not delete the cache entry for its own TID or the cache entries
explicitly configured with the tarp map command.

Examples The following example clears the TARP TID table:

clear tarp tid-table

Related Commands Command Description

show tarp map Lists all static entries in the TID cache that were configured with the tarp
map command.
show tarp tid-cache Displays information about the entries in the TID cache.
tarp allow-caching Reenables the storage of TID-to-NSAP address mapping in the TID cache.
tarp cache-timer Specifies the length of time that a dynamically created TARP entry remains
in the TID cache.
tarp map Enters a TID-to-NSAP static map entry in the TID cache.

Cisco IOS ISO CLNS Command Reference

P5R-11
 Cisco IOS ISO CLNS Commands
clns access-group

clns access-group
To filter transit CLNS traffic going either into or out of the router or both on a per-interface basis, use
the clns access-group command in interface configuration mode. To disable filtering of transit CLNS
packets, use the no form of this command.

clns access-group name [in | out]

no clns access-group name [in | out]

Syntax Description name Name of the filter set or expression to apply.

in (Optional) Filter should be applied to CLNS packets entering the router.
out (Optional) Filter should be applied to CLNS packets leaving the router. If
you do not specify an in or out keyword, out is assumed.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines This command has no effect on any CLNS packets sourced by Cisco IOS software. It applies only to
packets forwarded by the software. Fast switching is still supported with access groups in place, but its
performance will be impacted based on the complexity of the filters.
For descriptions of filter sets and expressions, refer to the clns filter-expr, clns filter-set, and clns
template-alias global configuration commands in this chapter.

Examples The following example enables forwarding of frames received on Ethernet 0 that had a source address
of anything other than 38.840F, and a destination address that started with 47.0005 or 47.0023, but
nothing else:
clns filter-set US-OR-NORDUNET permit 47.0005...
clns filter-set US-OR-NORDUNET permit 47.0023...
clns filter-set NO-ANSI deny 38.840F...
clns filter-set NO-ANSI permit default
clns filter-expr STRANGE source NO-ANSI and destination US-OR-NORDUNET

interface ethernet 0
clns access-group STRANGE in

Cisco IOS ISO CLNS Command Reference

P5R-12
 Cisco IOS ISO CLNS Commands
clns access-group

Related Commands Command Description

clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.
clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.
clns template-alias Builds a list of alphanumeric aliases of CLNS address templates for use in
the definition of CLNS filter sets.

Cisco IOS ISO CLNS Command Reference

P5R-13
 Cisco IOS ISO CLNS Commands
clns adjacency-filter

clns adjacency-filter
To filter the establishment of ES-IS adjacencies, use the clns adjacency-filter command in interface
configuration mode. To disable this filtering, use the no form of this command.

clns adjacency-filter {es | is} name

no clns adjacency-filter {es | is} name

Syntax Description es ES adjacencies are to be filtered.

is IS adjacencies are to be filtered.
name Name of the filter set or expression to apply.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Filtering is performed on full NSAP addresses. If filtering should only be performed on system IDs or
any other substring of the full NSAP address, the wildcard-matching capabilities of filter sets should be
used to ignore the insignificant portions of the NSAP addresses.

Note When you enter the clns adjacency-filter command, only the adjacencies that were formed using
ES-IS will be filtered out. In order to remove adjacencies that were formed using IS-IS and
ISO-IGRP, use the isis adjacency-filter and iso-igrp adjacency-filter commands, respectively.

For descriptions of filter sets and expressions, refer to the clns filter-expr, clns filter-set, and clns
template-alias global configuration commands in this chapter.

Examples The following example builds a filter that accepts end system adjacencies with only two systems, based
only on their system IDs:
clns filter-set ourfriends ...0000.0c00.1234.**
clns filter-set ourfriends ...0000.0c00.125a.**

interface ethernet 0
clns adjacency-filter es ourfriends

Cisco IOS ISO CLNS Command Reference

P5R-14
 Cisco IOS ISO CLNS Commands
clns adjacency-filter

Related Commands Command Description

clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.
clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.
clns template-alias Builds a list of alphanumeric aliases of CLNS address templates for use in
the definition of CLNS filter sets.
isis adjacency-filter Filters the establishment of IS-IS adjacencies.
iso-igrp Filters the establishment of ISO IGRP adjacencies.
adjacency-filter

Cisco IOS ISO CLNS Command Reference

P5R-15
 Cisco IOS ISO CLNS Commands
clns cache-invalidate-delay

clns cache-invalidate-delay
To control the invalidation rate of the CLNS route cache, use the clns cache-invalidate-delay command
in global configuration mode. To allow the CLNS route cache to be immediately invalidated, use the no
form of this command.

clns cache-invalidate-delay [minimum maximum quiet threshold]

no clns cache-invalidate-delay

Syntax Description minimum (Optional) Minimum time (in seconds) between invalidation request and
actual invalidation. The default is 2 seconds.
maximum (Optional) Maximum time (in seconds) between invalidation request and
actual invalidation. The default is 5 seconds.
quiet (Optional) Length of time (in seconds) before invalidation.
threshold (Optional) Maximum number of invalidations considered to be quiet.

Defaults minimum: 2 seconds

maximum: 5 seconds
quiet: 3 seconds
threshold: 0 invalidations

Command Modes Global configuration

Command History Release Modification

10.3 This command was introduced.

Usage Guidelines All cache invalidation requests are honored immediately.

This command should typically not be used except under the guidance of technical support personnel.
Incorrect settings can seriously degrade network performance.
In an environment with heavy traffic, the CLNS cache can get invalidated (purged) too frequently.
Frequent cache invalidations will cause the CPU to spend too much time purging and repopulating the
cache.
The clns cache-invalidate-delay command controls how the CLNS route cache is purged. The intent is
to delay invalidation of the cache until after routing has settled down. Because the routing table changes
tend to be clustered in a short period of time, and the cache may be purged repeatedly, a high CPU load
might be placed on the router.

Cisco IOS ISO CLNS Command Reference

P5R-16
 Cisco IOS ISO CLNS Commands
clns cache-invalidate-delay

When this feature is enabled, and the system requests that the route cache be purged, the request is held
for at least the minimum seconds. Then the system determines whether the cache has been “quiet” (that
is, less than threshold invalidation requests in the last quiet seconds). If the cache has been quiet, the
cache is then purged. If the cache does not become quiet within maximum seconds after the first request,
it is purged unconditionally.
Manipulation of these parameters trades off CPU utilization versus route convergence time. The timing
of routing protocols is not affected, but the removal of stale cache entries is affected.

Examples The following example sets a minimum delay of 5 seconds, a maximum delay of 30 seconds, and a quiet
threshold of no more than 5 invalidation requests in the previous 10 seconds:
clns cache-invalidate-delay 5 30 10 5

Related Commands Command Description

clns route-cache Allows fast switching through the cache.
show clns cache Displays the CLNS route cache.

Cisco IOS ISO CLNS Command Reference

P5R-17
 Cisco IOS ISO CLNS Commands
clns checksum

clns checksum
To enable checksum generation when ISO CLNS routing software sources a CLNS packet, use the clns
checksum command in interface configuration mode. To disable checksum generation, use the no form
of this command.

clns checksum

no clns checksum

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines This command has no effect on routing packets, such as ES-IS, ISO-Interior Gateway Routing Protocol
(IGRP) and IS-IS, sourced by the system. It applies to pings and trace route packets.

Examples The following example enables checksum generation:

interface ethernet 0
clns checksum

Cisco IOS ISO CLNS Command Reference

P5R-18
 Cisco IOS ISO CLNS Commands
clns cluster-alias

clns cluster-alias
To allow multiple end systems to advertise the same NSAP address but with different system IDs in ES
hello messages, use the clns cluster-alias command in interface configuration mode. To disable cluster
aliasing, use the no form of this command.

clns cluster-alias

no clns cluster-alias

Syntax Description This command has no arguments or keywords.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines This feature caches multiple ES adjacencies with the same NSAP, but with different subnetwork point
of attachment (SNPA) addresses. When a packet is destined to the common NSAP address, Cisco IOS
software load-splits the packets among the different SNPA addresses. A router that supports this
capability forwards traffic to each system.
If DECnet Phase V cluster aliases are disabled on an interface, ES hello packet information is used to
replace any existing adjacency information for the NSAP. Otherwise, an additional adjacency (with a
different SNPA) is created for the same NSAP.

Examples The following example enables cluster aliasing on specified interfaces:

clns nsap 47.0004.004d.0001.0000.0c00.1111.00
clns routing

interface ethernet 0
clns cluster-alias

interface ethernet 1
clns cluster-alias

Cisco IOS ISO CLNS Command Reference

P5R-19
 Cisco IOS ISO CLNS Commands
clns configuration-time

clns configuration-time
To specify the rate at which ES hellos and IS hellos are sent, use the clns configuration-time command
in global configuration mode. To restore the default value, use the no form of this command.

clns configuration-time seconds

no clns configuration-time

Syntax Description seconds Rate, in seconds, at which ES and IS hello packets are sent.

Defaults 60 seconds

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines The clns configuration-time command controls how frequently a router will send hello messages to its
adjacent routers. A hello message sent by the router contains the clns-holding time that tells the receiver
for how long it should consider the hello message valid. By default, the clns configuration-time is
60 seconds and the clns holding-time is 300 seconds.

Caution Do not set the clns configuration-time and the clns holding-time so that the clns
configuration-time is more than half of the clns holding-time. Doing so can lead to adjacencies
being reformed. When adjacencies are being reformed, the routers at either end of the adjacency will
flood their new link-state packet (LSP) routing packets throughout the network, forcing all routers to
recompute the network topology. If this situation occurs repeatedly, it can have a detrimental effect
on network performance.

Examples The following example specifies that ES hellos and IS hellos are to be sent every 100 seconds:
clns configuration-time 100

Cisco IOS ISO CLNS Command Reference

P5R-20
 Cisco IOS ISO CLNS Commands
clns configuration-time

Related Commands Command Description

clns esct-time Supplies an ES configuration timer option in a sent IS hello packet that tells
the ES how often it should send ES hello packet PDUs.
clns holding-time Allows the sender of an ES hello or IS hello packet to specify the length of
time you consider the information in the hello packets to be valid.

Cisco IOS ISO CLNS Command Reference

P5R-21
 Cisco IOS ISO CLNS Commands
clns congestion-threshold

clns congestion-threshold
To set the congestion experienced bit if the output queue has more than the specified number of packets
in it, use the clns congestion-threshold command in interface configuration mode. A number value of
zero or the no form of this command prevents this bit from being set. To remove the parameter setting
and set it to 0, use the no form of this command.

clns congestion-threshold number

no clns congestion-threshold

Syntax Description number Number of packets that are allowed in the output queue before the system
sets the congestion-experienced bit. The value zero (0) prevents this bit
from being set.

Defaults 4 packets

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines If a router configured for CLNS experiences congestion, it sets the congestion experienced bit. The
congestion threshold is a per-interface parameter set by this interface configuration command. An error
PDU (ERPDU) is sent to the sending router and the packet is dropped if the number of packets exceeds
the threshold.

Examples The following example sets the congestion threshold to 10:

interface ethernet 0
clns congestion-threshold 10

Cisco IOS ISO CLNS Command Reference

P5R-22
 Cisco IOS ISO CLNS Commands
clns dec-compatible

clns dec-compatible
To allow IS hellos sent and received to ignore the N-selector byte, use the clns dec-compatible
command in interface configuration mode. To disable this feature, use the no form of this command.

clns dec-compatible

no clns dec-compatible

Syntax Description This command has no arguments or keywords.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example enables DEC-compatible mode:

interface ethernet 0
clns dec-compatible

Cisco IOS ISO CLNS Command Reference

P5R-23
 Cisco IOS ISO CLNS Commands
clns enable

clns enable
If you do not intend to perform any dynamic routing on an interface, but intend to pass ISO CLNS packet
traffic to end systems, use the clns enable command in interface configuration mode. To disable ISO
CLNS on a particular interface, use the no form of this command.

clns enable

no clns enable

Syntax Description This command has no arguments or keywords.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example enables ISO CLNS on Ethernet interface 0:

interface ethernet 0
clns enable

Cisco IOS ISO CLNS Command Reference

P5R-24
 Cisco IOS ISO CLNS Commands
clns erpdu-interval

clns erpdu-interval
To determine the minimum interval time, in milliseconds, between error ERPDUs, use the clns
erpdu-interval command in interface configuration mode. A milliseconds value of zero or the no form
of this command turns off the interval and effectively sets no limit between ERPDUs.

clns erpdu-interval milliseconds

no clns erpdu-interval milliseconds

Syntax Description milliseconds Minimum interval time (in milliseconds) between ERPDUs.

Defaults 10 ms

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines This command prevents the router from sending ERPDUs more frequently than 1 per interface per
10 ms. It is wise not to send an ERPDU frequently if bandwidth is precious (such as over slow serial
lines).

Examples The following example sets the ERPDU interval to 30 ms:

interface ethernet 0
clns erpdu-interval 30

Related Commands Command Description

clns send-erpdu Allows CLNS to send an error PDU when the routing software detects an
error in a data PDU.

Cisco IOS ISO CLNS Command Reference

P5R-25
 Cisco IOS ISO CLNS Commands
clns esct-time

clns esct-time
To supply an ES configuration timer option in a transmitted IS hello packet that tells the ES how often
it should transmit ES hello packet PDUs, use the clns esct-time command in interface configuration
mode. To restore the default value and disable this function, use the no form of this command.

clns esct-time seconds

no clns esct-time seconds

Syntax Description seconds Time, in seconds, between ES hello PDUs. Range is from 0 to 65,535.

Defaults 0 seconds (disabled)

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example sets the ES configuration time to 10 seconds:

interface ethernet 0
clns esct-time 10

Related Commands Command Description

clns configuration-time Specifies the rate at which ES hello messages and IS hello messages are
sent.
clns holding-time Allows the sender of an ES hello or IS hello packet to specify the length
of time you consider the information in the hello packets to be valid.

Cisco IOS ISO CLNS Command Reference

P5R-26
 Cisco IOS ISO CLNS Commands
clns es-neighbor

clns es-neighbor
To manually define adjacencies for end systems that do not support the ES-IS routing protocol, use the
clns es-neighbor command in interface configuration mode. To delete the ES neighbor, use the no form
of this command.

clns es-neighbor nsap snpa

no clns es-neighbor nsap

Syntax Description nsap Specific NSAP to map to a specific data link address.
snpa Data link address.

Defaults No end systems are listed.

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines When you do use the clns es-neighbor command, you will have to manually specify the NSAP-to-SNPA
mapping for the adjacencies. The subnetwork point of attachment (SNPA) of the end system will depend
upon what type of interface is being used to provide connectively. On LANs, the SNPA will be a MAC
address.
If you have configured either the clns router iso-igrp or clns router isis interface configuration
commands for a particular interface, the ES-IS routing software automatically turns ES-IS on for that
interface.
It is only necessary to use static mapping for those end systems that do not support ES-IS. The Cisco IOS
software will continue to discover dynamically those end systems that do support ES-IS.

Examples The following example defines an ES neighbor on Ethernet interface 0:

interface ethernet 0
clns es-neighbor 47.0004.004D.0055.0000.0C00.A45B.00 0000.0C00.A45B

In this case, the end system with the following NSAP, or network entity title (NET), is configured with
an Ethernet MAC address of 0000.0C00.A45B:
47.0004.004D.0055.0000.0C00.A45B.00

Cisco IOS ISO CLNS Command Reference

P5R-27
 Cisco IOS ISO CLNS Commands
clns es-neighbor

Related Commands Command Description

clns host Defines a name-to-NSAP mapping that can then be used with commands
requiring NSAPs.
clns is-neighbor Defines all intermediate systems that will be used when you manually
specify the NSAP-to-SNPA mapping.
show clns es-neighbors Lists the ES neighbors that this router knows.

Cisco IOS ISO CLNS Command Reference

P5R-28
 Cisco IOS ISO CLNS Commands
clns filter-expr

clns filter-expr
To combine CLNS filter sets and CLNS address templates to create complex logical NSAP
pattern-matching expressions, use one or more clns filter-expr commands in global configuration mode.
To delete the expression, use the no form of this command.

clns filter-expr ename [term | not term | term {and | or | xor} term]

no clns filter-expr ename

Syntax Description ename Alphanumeric name to apply to this filter expression.

not (Optional) Defines a filter expression that is pattern matched only if the pattern
given by term is not matched.
and (Optional) Defines a filter expression that is pattern matched only if both of the
patterns given by the two terms are matched.
or (Optional) Defines a filter expression that is pattern matched if either of the
patterns given by the two terms is matched.
xor (Optional) Defines a filter expression that is pattern matched only if one of the
patterns, but not both, given by the two terms are matched.
term (Optional) Filter expression term. A term can be any of the following:
ename—Another, previously defined, filter expression.
sname (or destination sname)—A previously defined filter set name, with the
filter set applied to the destination NSAP address.
source sname—A previously defined filter set name, with the filter set applied to
the source NSAP address.

Defaults No filter expression is defined.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Filter expressions can reference previously defined filter expressions, so you can build arbitrarily
complex expressions.
If none of the optional keywords is used, then the command defines a simple filter expression that is
pattern matched only if the pattern given by term is matched.
Use this command to define complex filter expressions. See the description of the clns filter-set global
configuration command to learn how to define filter sets.

Cisco IOS ISO CLNS Command Reference

P5R-29
 Cisco IOS ISO CLNS Commands
clns filter-expr

Examples The following example defines a filter expression that matches addresses with a source address of
anything besides 39.840F, and a destination address that started with 47.0005 or 47.0023, but nothing
else:
clns filter-set US-OR-NORDUNET permit 47.0005...
clns filter-set US-OR-NORDUNET permit 47.0023
clns filter-set NO-ANSI deny 38.840F...
clns filter-set NO-ANSI permit default
!
clns filter-expr STRANGE source NO-ANSI and destination US-OR-NORDUNET

Related Commands Command Description

clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.
clns template-alias Builds a list of alphanumeric aliases of CLNS address templates for use in
the definition of CLNS filter sets.
show clns filter-expr Displays one or all currently defined CLNS filter expressions.

Cisco IOS ISO CLNS Command Reference

P5R-30
 Cisco IOS ISO CLNS Commands
clns filter-set

clns filter-set
To build a list of CLNS address templates with associated permit and deny conditions for use in CLNS
filter expressions, use the clns filter-set command in global configuration mode. CLNS filter
expressions are used in the creation and use of CLNS access lists. To delete the entire filter set, use the
no form of this command.

clns filter-set name [permit | deny] template

no clns filter-set name

Syntax Description name Alphanumeric name to apply to this filter set.

permit | deny (Optional) Addresses matching the pattern specified by template are to be
permitted or denied. If neither permit nor deny is specified, permit is
assumed.
template Address template, template alias name, or the keyword default. Address
templates and alias names are described under the description of the clns
template-alias global configuration command. The default keyword
denotes a zero-length prefix and matches any address.

Defaults No address templates are defined.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use this command to define a list of pattern matches and permit/deny conditions for use in CLNS filter
expressions. Filter expressions are used in the creation and use of CLNS access lists. See the description
of the clns filter-expr global configuration command to learn how to define filter expressions and the
clns template-alias global configuration command to learn how to define address templates and address
template aliases.
Each address that must be matched against a filter set is first compared against all the entries in the filter
set, in order, for an exact match with the address. If the exact match search fails to find a match, then the
entries in the filter set containing wildcard matches are scanned for a match, again, in order. The first
template that matches is used. If an address does not match any of the filter set entries, an implicit “deny”
is returned as the permit/deny action of the filter set.

Examples The following example returns a permit action if an address starts with either 47.0005 or 47.0023. It
returns an implicit deny action on any other address.
clns filter-set US-OR-NORDUNET permit 47.0005...
clns filter-set US-OR-NORDUNET permit 47.0023...

Cisco IOS ISO CLNS Command Reference

P5R-31
 Cisco IOS ISO CLNS Commands
clns filter-set

The following example returns a deny action if an address starts with 39.840F, but returns a permit action
for any other address:
clns filter-set NO-ANSI deny 38.840F...
clns filter-set NO-ANSI permit default

Related Commands Command Description

clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.
clns template-alias Builds a list of alphanumeric aliases of CLNS address templates for use in
the definition of CLNS filter sets.
show clns filter-set Displays one or all currently defined CLNS filter sets.

Cisco IOS ISO CLNS Command Reference

P5R-32
 Cisco IOS ISO CLNS Commands
clns holding-time

clns holding-time
To allow the sender of an ES hello or IS hello to specify the length of time for which you consider the
information in the hello packets to be valid, use the clns holding-time command in global configuration
mode. To restore the default value (300 seconds, or 5 minutes), use the no form of this command.

clns holding-time seconds

no clns holding-time

Syntax Description seconds Length of time, in seconds, during which the information in the hello packets
is considered valid.

Defaults 300 seconds (5 minutes)

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Setting this value too high puts extra traffic on a line and adds time to process hellos. However, you want
to avoid setting it too low if your topology changes more often than Cisco IOS software sends updates.

Examples The following example sets the holding time at 150 seconds:
clns holding-time 150

Related Commands Command Description

clns configuration-time Specifies the rate at which ES hello messages and IS hello messages are
sent.
clns esct-time Supplies an ES configuration timer option in a sent IS hello packet that
tells the ES how often it should send ES hello packet PDUs.

Cisco IOS ISO CLNS Command Reference

P5R-33
 Cisco IOS ISO CLNS Commands
clns host

clns host
To define a name-to-NSAP mapping that can then be used with commands that require NSAPs, use the
clns host command in global configuration mode.

clns host name nsap

Syntax Description name Desired name for the NSAP. The first character can be either a letter or a
number, but if you use a number, the operations you can perform are limited.
nsap NSAP to which that the name maps.

Defaults No mapping is defined.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines The assigned NSAP name is displayed, where applicable, in show and debug EXEC commands. There
are some effects and requirements associated with using names to represent network entity titles (NETs)
and NSAPs, however. Although using names as proxies for addresses is allowed with CLNS commands,
they are never written out to nonvolatile random-access memory (NVRAM).
The first character can be either a letter or a number, but if you use a number, the operations you can
perform (such as ping) are limited.
The clns host command is generated after all other CLNS commands when the configuration file is
parsed. As a result, the NVRAM version of the configuration cannot be edited to specifically change the
address defined in the original clns host command. You must specifically change any commands that
refer to the original address. This affects all commands that accept names.
The commands that are affected by these requirements include the following:
• net (router configuration command)
• clns is-neighbor (interface configuration command)
• clns es-neighbor (interface configuration command)
• clns route (global configuration command)

Examples The following example defines names to NSAPs:

clns host cisco1 39.0001.0000.0c00.1111.00
clns host cisco2 39.0002.0000.0c00.1111.00
router iso-igrp
net cisco1
!

Cisco IOS ISO CLNS Command Reference

P5R-34
 Cisco IOS ISO CLNS Commands
clns host

interface ethernet 0
clns net cisco2

Related Commands Command Description

clns es-neighbor Defines all end systems that will be used when you manually specify the
NSAP-to-SNPA mapping.
clns is-neighbor Defines all intermediate systems that will be used when you manually
specify the NSAP-to-SNPA mapping.
net Configures a NET for a CLNS routing process.

Cisco IOS ISO CLNS Command Reference

P5R-35
 Cisco IOS ISO CLNS Commands
clns is-neighbor

clns is-neighbor
To manually define adjacencies for intermediate systems, use the clns is-neighbor command in
interface configuration mode. To delete the specified IS neighbor, use the no form of this command.

clns is-neighbor nsap snpa

no clns is-neighbor nsap

Syntax Description nsap NSAP of a specific intermediate system to enter as neighbor to a specific data
link address.
snpa Data link address.

Defaults No intermediate systems are listed.

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines When you do use the clns is-neighbor command, you will have to manually specify the NSAP-to-SNPA
mapping for the adjacencies. The subnetwork point of attachments (SNPAs) are the MAC addresses. The
SNPA of the end system will depend upon what type of interface is being used to provide connectively.
On LANs, the SNPA will be a MAC address.
It is sometimes preferable for a router to have a neighbor entry statically configured rather than learned
through ES-IS, ISO IGRP, or IS-IS. This interface configuration command enters an IS neighbor.

Examples The following example defines an IS neighbor on Ethernet interface 0:

interface ethernet 0
clns is-neighbor 47.0004.004D.0055.0000.0C00.A45B.00 0000.0C00.A45B

Related Commands Command Description

clns es-neighbor Defines all end systems that will be used when you manually specify the
NSAP-to-SNPA mapping.
clns host Defines a name-to-NSAP mapping that can then be used with commands
requiring NSAPs.
show clns is-neighbors Displays IS-IS related information for IS-IS router adjacencies.

Cisco IOS ISO CLNS Command Reference

P5R-36
 Cisco IOS ISO CLNS Commands
clns mtu

clns mtu
To set the maximum transmission unit (MTU) packet size for the interface, use the clns mtu command
in interface configuration mode. To restore the default and maximum packet size, use the no form of this
command.

clns mtu bytes

no clns mtu

Syntax Description bytes Maximum packet size in bytes. The minimum value is 512; the default and
maximum packet size depend on the interface type.

Defaults Depends on interface type

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines All interfaces have a default maximum packet size. You can set the MTU size of the packets sent on the
interface with the mtu interface configuration command.
All routers on a physical medium must have the same protocol MTU in order to operate.
The CTR card does not support the switching of frames larger than 4472 bytes. Interoperability problems
can occur if CTR cards are intermixed with other Token Ring cards on the same network. These problems
can be minimized by lowering the CLNS MTUs to be the same on all routers on the network with the
clns mtu command.

Note Changing the MTU value with the mtu interface configuration command can affect the CLNS MTU
value. If the CLNS MTU is at its maximum given the interface MTU, the CLNS MTU will change
with the interface MTU. However, the reverse is not true; changing the CLNS MTU value has no
effect on the value for the mtu interface configuration command.

Examples The following example sets the MTU packet size to 1000 bytes:
interface ethernet 0
clns mtu 1000

Cisco IOS ISO CLNS Command Reference

P5R-37
 Cisco IOS ISO CLNS Commands
clns mtu

Related Commands Command Description

mtu Adjusts the maximum packet size or MTU size.

Cisco IOS ISO CLNS Command Reference

P5R-38
 Cisco IOS ISO CLNS Commands
clns net (global)

clns net (global)

To assign a static address for a router, use the clns net command in global configuration mode. If the
Cisco IOS software is configured to support ISO CLNS, but is not configured to dynamically route
CLNS packets using ISO IGRP or IS-IS, use this command to assign an address to the router. To remove
any previously configured NET or NSAP address, use the no form of this command.

clns net {net-address | name}

no clns net {net-address | name}

Syntax Description net-address NET address. Refer to the “Usage Guidelines” section.
name CLNS host name to be associated with this interface.

Defaults No static address is assigned.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines A CLNS packet sent to any of the defined NSAPs or NETs will be received by the router. The Cisco IOS
software chooses the NET to use when it sends a packet with the following algorithm:
• If no dynamic routing protocol is running, use the NET defined for the outgoing interface if it exists;
otherwise, use the NET defined for the router.
• If ISO IGRP is running, use the NET of the routing process that is running on this interface.
• If IS-IS is running, use the NET of the IS-IS routing process that is running on this interface.

Examples The following example assigns a static address:

clns net 49.0001.aa00.0400.9105.00

Cisco IOS ISO CLNS Command Reference

P5R-39
 Cisco IOS ISO CLNS Commands
clns net (interface)

clns net (interface)

To assign an NSAP address or name to a router interface, use the clns net command in interface
configuration mode. If Cisco IOS software is configured to support ISO CLNS, but is not configured to
dynamically route CLNS packets using an ISO IGRP or IS-IS, use this command to assign an address to
the router. To remove any previously configured NSAP address, use the no form of this command.

clns net {nsap-address | name}

no clns net {nsap-address | name}

Syntax Description nsap-address Specific NSAP address.

name Name to be associated with this interface.

Defaults No address or name is assigned.

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines This command is useful if you are doing static routing and need to control the source NET used by the
router on each interface.

Examples The following example assigns an NSAP address to a router interface:

interface ethernet 0
clns net 49.0001.0000.0c00.1111.00

The following example assigns a name to a router interface:

interface ethernet 0
clns net cisco

Cisco IOS ISO CLNS Command Reference

P5R-40
 Cisco IOS ISO CLNS Commands
clns packet-lifetime

clns packet-lifetime
To specify the initial lifetime for locally generated packets, use the clns packet-lifetime command in
global configuration mode. To remove the parameter’s settings, use the no form of this command.

clns packet-lifetime seconds

no clns packet-lifetime

Syntax Description seconds Packet lifetime in seconds.

Defaults 32 seconds

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example sets a packet lifetime of 120 seconds:

clns packet-lifetime 120

Related Commands Command Description

clns want-erpdu Specifies whether to request ERPDUs on packets sourced by the router.

Cisco IOS ISO CLNS Command Reference

P5R-41
 Cisco IOS ISO CLNS Commands
clns rdpdu-interval

clns rdpdu-interval
To determine the minimum interval time between redirect PDUs (RDPDUs), use the clns
rdpdu-interval command in interface configuration mode. To turn off the interval rate and effectively
set no limit between RDPDUs, use the no form of this command or a milliseconds value of zero.

clns rdpdu-interval milliseconds

no clns rdpdu-interval milliseconds

Syntax Description milliseconds Minimum interval time in milliseconds between RDPDUs.

Defaults 100 ms

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines RDPDUs are rate-limited and are not sent more frequently than one per interface per 100 ms. There is
no need to change the default. This setting will work fine for most networks.

Examples The following example sets an interval of 50 ms:

interface ethernet 0
clns rdpdu-interval 50

Related Commands Command Description

clns send-rdpdu Allows CLNS to send RPDUs when a better route for a given host is known.

Cisco IOS ISO CLNS Command Reference

P5R-42
 Cisco IOS ISO CLNS Commands
clns route (create)

clns route (create)

To create an interface static route, use this form of the clns route command in global configuration
mode. To remove this route, use the no form of this command.

clns route nsap-prefix type number [snpa-address]

no clns route nsap-prefix

Syntax Description nsap-prefix Network service access point prefix. This value is entered into a static
routing table and used to match the beginning of a destination NSAP. The
longest NSAP-prefix entry that matches is used.
type Interface type.
number Interface number.
snpa-address (Optional) Specific subnetwork point of attachment (SNPA) address.
Optional for serial links; required for multiaccess networks.

Defaults No interface static routes are created.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines CLNS static routes will not be used to route traffic to a destination for which there is a dynamic route,
if that destination is within the domain (ISO-IGRP) or area (IS-IS) of the router.

Note If you do not specify an SNPA address when you have a multiaccess network, you will receive an
error message indicating a bad SNPA.

Examples The following example creates a static route for an Ethernet interface:
clns route 39.0002 ethernet 3 aa00.0400.1111

The following example creates a static route for a serial interface:

clns route 39.0002 serial 0

Cisco IOS ISO CLNS Command Reference

P5R-43
 Cisco IOS ISO CLNS Commands
clns route (create)

Related Commands Command Description

clns route (enter) Enters a specific static route.
clns route default Configures a default zero-length prefix rather than typing an NSAP prefix.
clns route discard Explicitly tells a router to discard packets with NSAP addresses that match the
specified nsap-prefix.

Cisco IOS ISO CLNS Command Reference

P5R-44
 Cisco IOS ISO CLNS Commands
clns route (enter)

clns route (enter)

To enter a specific static route, use this form of the clns route command in global configuration mode.
NSAPs that start with nsap-prefix are forwarded to next-hop-net or the name of the next hop. To remove
this route, use the no form of this command.

clns route nsap-prefix {next-hop-net | name}

no clns route nsap-prefix

Syntax Description nsap-prefix Network service access point prefix. This value is entered into a static
routing table and used to match the beginning of a destination NSAP. The
longest NSAP-prefix entry that matches is used.
next-hop-net Next-hop NET. This value is used to establish the next hop of the route for
forwarding packets.
name Name of the next hop node. This value can be used instead of the next-hop
NET to establish the next hop of the route for forwarding packets.

Defaults No static route is entered.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines CLNS static routes will not be used to route traffic to a destination for which there is a dynamic route,
if that destination is within the domain (ISO-IGRP) or area (IS-IS) of the router.

Examples The following example forwards all packets toward the specified route:
clns route 39.840F 47.0005.80FF.FF00.0123.4567.89AB.00

Related Commands Command Description

clns route (create) Creates an interface static route.
clns route default Configures a default zero-length prefix rather than typing an NSAP prefix.
clns route discard Explicitly tells a router to discard packets with NSAP addresses that match
the specified nsap-prefix.

Cisco IOS ISO CLNS Command Reference

P5R-45
 Cisco IOS ISO CLNS Commands
clns route-cache

clns route-cache
To allow fast switching through the cache, use the clns route-cache command in interface configuration
mode. To disable fast switching, use the no form of this command.

clns route-cache

no clns route-cache

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines The cache still exists and is used after the no clns route-cache command is used; the software just does
not do fast switching through the cache.

Examples The following example allows fast switching through the cache:
interface ethernet 0
clns route-cache

Cisco IOS ISO CLNS Command Reference

P5R-46
 Cisco IOS ISO CLNS Commands
clns route default

clns route default

To configure a default zero-length prefix rather than type an NSAP prefix, use the clns route default
command in global configuration mode. To remove this route, use the no form of this command.

clns route default type number

no clns route default

Syntax Description type Interface type. Specify the interface type immediately followed by the
interface number; there is no space between the two.
number Interface number.

Defaults No default prefix is configured.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example configures a default zero-length prefix:

clns route default ethernet0

Related Commands Command Description

clns route (interface static route) Creates an interface static route.
clns route (enter) Enters a specific static route.
clns route discard Explicitly tells a router to discard packets with NSAP addresses
that match the specified nsap-prefix.

Cisco IOS ISO CLNS Command Reference

P5R-47
 Cisco IOS ISO CLNS Commands
clns route default discard

clns route default discard

To assign a default discard route and automatically discard packets with NSAP addresses that do not
match any existing routes, use the clns route default discard command in global configuration mode.
To remove the default discard route, use the no form of this command.

clns route default discard

no clns route default discard

Syntax Description This command has no arguments or keywords.

Defaults Disabled

Command Modes Global configuration

Command History Release Modification

11.0 This command was introduced.

Usage Guidelines The only time you would use this command is if you are using static routing and ES-IS and you wish
disable ES-IS and therefore reduce the router to using purely static routing. Using this command will
reduce the functionality of the router by forcing ISO CLNS to ignore all nodes that were learned through
ES-IS.

Note This command will have little or no affect if you are using a dynamic routing process such as IS-IS
or ISO-IGRP, as the router will discard any packets for which it does not have a route, even if this
command has not been entered.

Examples The following example assigns a default discard route:

clns route default discard

When you enter the enter the show clns route command, you will see the following default discard route
information:
#show clns route

Codes: C - connected, S - static, d - DecnetIV

I - ISO-IGRP, i - IS-IS, e - ES-IS
S Default Prefix [10/0], Discard Entry

Cisco IOS ISO CLNS Command Reference

P5R-48
 Cisco IOS ISO CLNS Commands
clns route default discard

Related Commands Command Description

clns route discard Explicitly tells a router to discard packets with NSAP addresses
that match the specified nsap-prefix.
show clns route Displays all of the destinations to which this router knows how
to route packets.

Cisco IOS ISO CLNS Command Reference

P5R-49
 Cisco IOS ISO CLNS Commands
clns route discard

clns route discard

To explicitly tell a router to discard packets with NSAP addresses that match the specified nsap-prefix,
use the clns route discard command in global configuration mode. To remove this route, use the no form
of this command.

clns route nsap-prefix discard

no clns route nsap-prefix

Syntax Description nsap-prefix Network service access point prefix. This value is entered into a static
routing table and used to match the beginning of a destination NSAP. The
longest NSAP-prefix entry that matches is used.
discard The router discards packets with NSAPs that match the specified value for
the nsap-prefix argument.

Defaults No NSAP addresses are identified.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines The decnet advertise command and the clns route discard command work together when DECnet
Phase IV/V conversion is enabled. Any packet with the specified CLNS NSAP prefix causes CLNS to
behave as if no route were found. Because DECnet Phase IV/V conversion is enabled, the route is then
looked up in the Phase IV routing table. The router that is advertising the DECnet Phase IV route
converts the packet to OSI and sends it to the router that is advertising the CLNS discard static route.
Once it gets there, the packet is converted back to Phase IV.
CLNS discard routes cannot be used to discard packets that are addressed to a destination for which there
is a dynamic route, if that destination is within the domain (ISO IGRP) or area (IS-IS) of the router.

Examples The following example discards packets with a destination NSAP address that matches the prefix
47.0005:
clns route 47.0005 discard

Cisco IOS ISO CLNS Command Reference

P5R-50
 Cisco IOS ISO CLNS Commands
clns route discard

Related Commands Command Description

clns route (enter) Enters a specific static route.
clns route (interface static route) Creates an interface static route.
clns route default Configures a default zero-length prefix rather than typing an
NSAP prefix.
decnet advertise Configures border routers to propagate Phase IV areas through
an OSI backbone.

Cisco IOS ISO CLNS Command Reference

P5R-51
 Cisco IOS ISO CLNS Commands
clns router isis

clns router isis

To configure an Intermediate System-to-Intermediate System (IS-IS) routing process for ISO
Connectionless Network Service Protocol (CLNS) on a specified interface and to attach an area
designator to the routing process, use the clns router isis command in interface configuration mode. To
disable IS-IS for ISO CLNS, use the no form of the command.

clns router isis area-tag

no clns router isis area-tag

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Defines a meaningful name for an area routing process. If not specified, a
null tag is assumed. It must be unique among all CLNS router processes for
a given router. The area-tag argument is used later as a reference to this area
routing process.
Each area in a multiarea configuration should have a non-null area tag to
facilitate identification of the area.

Defaults No routing processes are specified.

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.
12.0(5)T Multiarea functionality was added, changing the way the tag argument (now
area-tag) is used.

Usage Guidelines Before the IS-IS router process is useful, a network entity title (NET) must be assigned with the net
command and some interfaces must be enabled with IS-IS.
If you have IS-IS running and at least one ISO-IGRP process, the IS-IS process and the ISO-IGRP
process cannot both be configured without an area tag. The null tag can be used by only one process. If
you run ISO-IGRP and IS-IS, a null tag can be used for IS-IS, but not for ISO-Interior Gateway Routing
Protocol (IGRP) at the same time. However, each area in an IS-IS multiarea configuration should have
a non-null area tag to facilitate identification of the area.
You can configure only one process to perform Level 2 (interarea) routing. If Level 2 routing is
configured on any process, all additional processes are automatically configured as Level 1. You can
configure this process to perform intra-area (Level 1) routing at the same time. You can configure up to
29 additional processes as Level 1-only processes. Use the is-type command to remove Level 2 routing
from a router instance. You can then use the is-type command to enable Level 2 routing on some other
IS-IS router instance.

Cisco IOS ISO CLNS Command Reference

P5R-52
 Cisco IOS ISO CLNS Commands
clns router isis

Note The CPU memory required to run 29 Level 1 ISIS processes will probably not be present in low-end
platforms unless the routing information and area topology are limited.

An interface cannot be part of more than one area, except in the case where the associated routing
process is performing both Level 1 and Level 2 routing. On media (such as WAN media, for example)
where subinterfaces are supported, different subinterfaces could be configured for different areas.

Examples The following example enables IS-IS routing for ISO CLNS on Ethernet interface 0:
router isis cisco
net 39.0001.0000.0c00.1111.00
interface ethernet 0
clns router isis cisco

The following example shows an IS-IS configuration with two Level 1 areas and one Level 1-2 area:
clns routing

...

interface Tunnel529
clns router isis BB

interface Ethernet1
clns router isis A3253-01
!
interface Ethernet2
clns router isis A3253-02

...

router isis BB ! Defaults to "is-type level-1-2"

net 49.2222.0000.0000.0005.00
!
router isis A3253-01
net 49.0553.0001.0000.0000.0005.00
is-type level-1
!
router isis A3253-02
net 49.0553.0002.0000.0000.0005.00
is-type level-1

Related Commands Command Description

router isis Enables the IS-IS routing protocol and specifies an IS-IS process for IP.

Cisco IOS ISO CLNS Command Reference

P5R-53
 Cisco IOS ISO CLNS Commands
clns router iso-igrp

clns router iso-igrp

To specify ISO IGRP routing on a specified interface, use the clns router iso-igrp command in interface
configuration mode. To disable ISO IGRP routing for the system, use the no form of the global
configuration command with the appropriate tag.

clns router iso-igrp tag [level 2]

no clns router iso-igrp tag

Syntax Description tag Meaningful name for routing process. It must be unique among all CLNS
router processes for a given router. This tag should be the same as defined
for the routing process in the router iso-igrp global configuration command.
level 2 (Optional) Allows the interface to advertise Level 2 information.

Defaults ISO IGRP routing is not specified on any interface.

Command Modes Interface configuration

Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines If you want this interface to advertise Level 2 information only, use the level 2 keyword. This option
reduces the amount of router-to-router traffic by telling Cisco IOS software to send out only Level 2
routing updates on certain interfaces. Level 1 information is not passed on the interfaces for which the
Level 2 option is set.

Examples In the following example, the interface advertises Level 2 information only on serial interface 0:
router iso-igrp marketing
net 49.0001.0000.0c00.1111.00
interface serial 0
clns router iso-igrp marketing level 2

Related Commands Command Description

router iso-igrp Identifies the area the router will work in and informs it that it will route
dynamically using the ISO IGRP protocol.

Cisco IOS ISO CLNS Command Reference

P5R-54
 Cisco IOS ISO CLNS Commands
clns routing

clns routing
To enable routing of CLNS packets, use the clns routing command in global configuration mode. To
disable CLNS routing, use the no form of this command.

clns routing

no clns routing

Syntax Description This command has no arguments or keywords.

Defaults Disabled

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example enables routing of CLNS packets:

clns routing

Related Commands Command Description

clns security pass-through Allows Cisco IOS software to pass packets that have security options
set.

Cisco IOS ISO CLNS Command Reference

P5R-55
 Cisco IOS ISO CLNS Commands
clns security pass-through

clns security pass-through

To allow Cisco IOS software to pass packets that have security options set, use the clns security
pass-through command in global configuration mode. To disable this function, use the no form of this
command.

clns security pass-through

no clns security pass-through

Syntax Description This command has no arguments or keywords.

Defaults The software discards any packets it sees as set with security options.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Examples The following example allows Cisco IOS software to pass packets that have security options set:
clns routing
router iso-igrp
net 47.0004.004d.0001.0000.0c11.1111.00
clns security pass-through

Related Commands Command Description

clns routing Enables routing of CLNS packets.

Cisco IOS ISO CLNS Command Reference

P5R-56
 Cisco IOS ISO CLNS Commands
clns send-erpdu

clns send-erpdu
To allow CLNS to send an error PDU when the routing software detects an error in a data PDU, use the
clns send-erpdu command in interface configuration mode. To disable this function, use the no form of
this command.

clns send-erpdu

no clns send-erpdu

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines When a CLNS packet comes in, the routing software looks in the routing table for the next hop. If it does
not find the next hop, the packet is discarded and an ERPDU can be sent to the original source/sender of
the packet that was discarded.

Examples The following example allows CLNS to send an error PDU when it detects an error in a data PDU:
interface ethernet 0
clns send-erpdu

Related Commands Command Description

clns erpdu-interval Determines the minimum interval time, in milliseconds, between error
ERPDUs.

Cisco IOS ISO CLNS Command Reference

P5R-57
 Cisco IOS ISO CLNS Commands
clns send-rdpdu

clns send-rdpdu
To allow CLNS to redirect PDUs (RDPDUs) when a better route for a given host is known, use the clns
send-rdpdu command in interface configuration mode. To disable this function, use the no form of this
command.

clns send-rdpdu

no clns send-rdpdu

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines If a packet is sent out on the same interface it came in on, an RDPDU can also be sent to the sender of
the packet.

Examples The following example allows CLNS to send RDPDUs:

interface ethernet 0
clns send-rdpdu

Related Commands Command Description

clns erpdu-interval Determines the minimum interval time (in milliseconds) between RDPDUs.

Cisco IOS ISO CLNS Command Reference

P5R-58
 Cisco IOS ISO CLNS Commands
clns split-horizon

clns split-horizon
To implement split horizon for ISO IGRP updates, use the clns split-horizon command in interface
configuration mode. To disable this function, use the no form of this command.

clns split-horizon

no clns split-horizon

Syntax Description This command has no arguments or keywords.

Defaults For all LAN interfaces—enabled

For WAN interfaces on X.25, Frame Relay, or SMDS networks—disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Normally, routers that are connected to broadcast-type OSI networks and that use distance vector routing
protocols employ the split-horizon mechanism to prevent routing loops. Split-horizon blocks
information about routes from being advertised by a router out any interface from which that information
originated. This behavior usually optimizes communications among multiple routers, particularly when
links are broken. However, with nonbroadcast networks, such as Frame Relay and SMDS, situations can
arise for which this behavior is less than ideal. For all interfaces except those for which either Frame
Relay or SMDS encapsulation is enabled, the default condition for this command is for split horizon to
be enabled.
If your configuration includes either the encapsulation frame-relay or encapsulation smds interface
configuration commands, the default is for split horizon to be disabled. Split horizon is not disabled by
default for interfaces using any of the X.25 encapsulations.
For networks that include links over X.25 PSNs, the neighbor interface configuration command can be
used to defeat the split horizon feature. You can as an alternative explicitly specify the
no clns split-horizon command in your configuration. However, if you do so, you must similarly disable
split horizon for all routers in any relevant multicast groups on that network.
Split horizon for ISO IGRP defaults to off for X.25, SMDS, and Frame Relay. Thereby, destinations are
advertised out the interface for which the router has a destination.
In general, changing the state of the default for this interface configuration command is not
recommended, unless you are certain that your application requires making a change in order to properly
advertise routes. Remember that if split horizon is disabled on a serial interface (and that interface is
attached to a packet-switched network), you must disable split horizon for all routers in any relevant
multicast groups on that network.

Cisco IOS ISO CLNS Command Reference

P5R-59
 Cisco IOS ISO CLNS Commands
clns split-horizon

Examples The following example disables split horizon on a serial link connected to an X.25 network:
interface serial 0
encapsulation x25
no clns split-horizon

Cisco IOS ISO CLNS Command Reference

P5R-60
 Cisco IOS ISO CLNS Commands
clns template-alias

clns template-alias
To build a list of alphanumeric aliases of CLNS address templates for use in the definition of CLNS filter
sets, use one or more clns template-alias commands in global configuration mode. To delete the alias,
use the no form of this command.

clns template-alias name template

no clns template-alias name

Syntax Description name Alphanumeric name to apply as an alias for the template.
template Address template, as defined in the “Usage Guidelines” section.

Defaults No alias list is defined.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Address templates are “pattern forms” that match one or more CLNS addresses. They can be simple
single CLNS addresses, which match just themselves, or contain wildcards, prefixes, and suffixes,
allowing a single template to match many addresses.
The simplest address template matches just a single address, as shown in this example:
47.0005.1234.5678.9abc.def0.00

Wildcard digits, which can match any value, are indicated with asterisks (*). The following template
matches the above address and any other 12-byte long address that starts with 47.0005.1234.5678:
47.0005.1234.5678.****.****.**

Because OSI addresses are variable in length, it is often useful to build templates that match addresses
that share a common prefix. The following template matches any address of any length that begins with
the prefix 47.0005.1234.5678:
47.0005.1234.5678...

In other instances, matching a suffix of the address is also important, such as when matching system IDs.
The following template matches any address that ends with the suffix 0000.0c01.2345.00:
...0000.0c01.2345.00

In other cases, you might want to match addresses on a single-bit granularity, rather than half-byte
(four-bit, or nibble) granularity. This pattern matching is supported by allowing the hex digits that
represent four bits to be replaced by groups of four binary bits, represented by 0s and 1s. These four

Cisco IOS ISO CLNS Command Reference

P5R-61
 Cisco IOS ISO CLNS Commands
clns template-alias

binary digits are enclosed within parentheses. The following template matches any address that starts
with 47.0005 followed by the binary bits 10. The final two binary bits in the nibble can be either 0 or 1,
and are represented with asterisks.
47.0005.(10**)...

Use this command to define aliases for commonly referenced address templates. The use of these aliases
reduces the chances for typographical error in the creation of CLNS filter sets.

Examples The following command defines a filter set called COMPLEX-PREFIX for the last example given in the
“Usage Guidelines” section:
clns template-alias COMPLEX-PREFIX 47.0005.(10**)...

Related Commands Command Description

clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.
clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.

Cisco IOS ISO CLNS Command Reference

P5R-62
 Cisco IOS ISO CLNS Commands
clns want-erpdu

clns want-erpdu
To specify whether to request ERPDUs on packets sourced by the router, use the clns want-erpdu
command in global configuration mode. To remove the parameter’s settings, use the no form of this
command.

clns want-erpdu

no clns want-erpdu

Syntax Description This command has no arguments or keywords.

Defaults To request ERPDUs

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines This command has no effect on routing packets (ES-IS, ISO IGRP, and IS-IS) sourced by the system. It
applies to pings and trace route packets.

Examples The following example requests ERPDUs on packets sourced by the router:
clns want-erpdu

Related Commands Command Description

clns packet-lifetime Specifies the initial lifetime for locally generated packets.

Cisco IOS ISO CLNS Command Reference

P5R-63
 Cisco IOS ISO CLNS Commands
ctunnel destination

ctunnel destination
To configure the destination parameter for an IP over CLNS tunnel (CTunnel), use the ctunnel
destination command in interface configuration mode. To remove the destination parameter, use the no
form of this command.

ctunnel destination nsap-address

no ctunnel destination nsap-address

Syntax Description nsap-address NSAP address for the CTunnel destination.

Defaults No default behavior or values.

Command Modes Interface configuration

Command History Release Modification

12.1(5)T This command was introduced.

Usage Guidelines When creating an IP over CLNS tunnel, you must first create the virtual interface by using the
interface ctunnel command. Once you have created the virtual interface, the order in which you
configure the destination parameter by using the ctunnel destination command and set the IP address
for that destination parameter by using the ip address command does not matter.
Addresses in the ISO network architecture are referred to as network service access point (NSAP)
addresses and network entity titles (NETs). Each node in an OSI network has one or more NETs. In
addition, each node has many NSAP addresses. Each NSAP address differs from one of the NETs for
that node in only the last byte. This byte is called the N-selector. Its function is similar to the port number
in other protocol suites.
When a CTunnel interface is being configured, the N-selector of the destination NSAP address is set
automatically by the router. Regardless of the value you enter for the N-selector byte, the router will
select the appropriate value. You will see the value that was chosen by the router when you enter the
show interfaces ctunnel command.

Examples The following example configures a CTunnel from one router to another and shows the CTunnel
destination set to 49.0001.1111.1111.1111.00.
interface ctunnel 301
ip address 10.0.0.3 255.255.255.0
ctunnel destination 49.0001.1111.1111.1111.00

Cisco IOS ISO CLNS Command Reference

P5R-64
 Cisco IOS ISO CLNS Commands
ctunnel destination

Related Commands Command Description

clns routing Enables routing of CLNS packets.
debug ctunnel Displays debug messages for the IP over a CLNS Tunnel feature.
interface ctunnel Creates a virtual interface to transport IP over a CLNS tunnel.
ip address Sets a primary or secondary IP address for an interface.
ip routing Enables IP routing.

Cisco IOS ISO CLNS Command Reference

P5R-65
 Cisco IOS ISO CLNS Commands
distance (ISO CLNS)

distance (ISO CLNS)

To configure the administrative distance for CLNS routes learned, use the distance command in router
configuration mode. To restore the administrative distance to the default, use the no form of this
command.

distance value [clns]

no distance value [clns]

Syntax Description value Administrative distance, indicating the trustworthiness of a routing

information source. This argument has a numerical value between 0 and 255.
A higher relative value indicates a lower trustworthiness rating. Preference is
given to routes with smaller values.
clns (Optional) CLNS-derived routes for IS-IS.

Defaults Static routes—10

ISO IGRP routes—100
IS-IS routes—110

Command Modes Router configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines When multiple routing processes are running in the same router for CLNS, it is possible for the same
route to be advertised by more than one routing process.
If the router is forwarding packets, dynamic routes will always take priority over static routes, unless the
router is routing to a destination outside of its domain and area. The router first will look for an ISO
IGRP route within its own area, then for an ISO IGRP route within its own domain, and finally for an
IS-IS route within its own area, until it finds a matching route. If a matching route still has not been
found, the router will check its prefix table, which contains static routes and routes to destinations
outside the area (ISO IGRP), domain (ISO IGRP), and area (IS-IS) routes for that router. When the router
is using its prefix table, it will choose the route that has the lowest administrative distance.

Cisco IOS ISO CLNS Command Reference

P5R-66
 Cisco IOS ISO CLNS Commands
distance (ISO CLNS)

Note The administrative distance for CLNS routes that you have configured by entering the distance
command will take effect only when routes are entered into the routing prefix table.

If you want an ISO IGRP pre

fix route to override a static route, you must set the administrative distance for the routing process to be
lower than 10 (assigned administrative distance for static routes). You cannot change the assigned
administrative distance for static routes.
The show clns protocol EXEC command displays the default administrative distance for a specified
routing process.

Examples In the following example, the distance value for CLNS routes learned is 90. Preference is given to these
CLNS routes rather than routes with the default administrative distance value of 110.
router isis
distance 90 clns

Cisco IOS ISO CLNS Command Reference

P5R-67
 Cisco IOS ISO CLNS Commands
ignore-lsp-errors

ignore-lsp-errors
To allow the router to ignore Intermediate System-to-Intermediate System (IS-IS) link-state packets that
are received with internal checksum errors rather than purging the link-state packets, use the
ignore-lsp-errors command in router configuration mode. To disable this function, use the no form of
this command.

ignore-lsp-errors

no ignore-lsp-errors

Syntax Description This command has no arguments or keywords.

Defaults This command is enabled by default; that is, corrupted LSPs are dropped instead of purged for network
stability.

Command Modes Router configuration

Command History Release Modification

11.1 This command was introduced.
12.0 This command is now enabled by default.

Usage Guidelines The IS-IS protocol definition requires that a received link-state packet with an incorrect data-link
checksum be purged by the receiver, which causes the initiator of the packet to regenerate it. However,
if a network has a link that causes data corruption while still delivering link-state packets with correct
data link checksums, a continuous cycle of purging and regenerating large numbers of packets can occur.
Because this could render the network nonfunctional, use the ignore-lsp-errors command to ignore
these link-state packets rather than purge the packets.
Link-state packets are used by the receiving routers to maintain their routing tables.
If you want to explicitly purge the corrupted LSPs, issue the no ignore-lsp-errors command.

Examples The following example instructs the router to ignore link-state packets that have internal checksum
errors:
router isis
ignore-lsp-errors

Cisco IOS ISO CLNS Command Reference

P5R-68
 Cisco IOS ISO CLNS Commands
interface ctunnel

interface ctunnel
To create a virtual interface to transport IP over a CLNS tunnel (CTunnel), use the interface ctunnel
command in global configuration mode. To remove the virtual interface, use the no form of this
command.

interface ctunnel interface-number

no interface ctunnel interface-number

Syntax Description interface-number CTunnel interface number (a number from 0 through 2,147,483,647).

Defaults No default behavior or values.

Command Modes Global configuration

Command History Release Modification

12.1(5)T This command was introduced.

Usage Guidelines When configuring an IP over CLNS tunnel, you must first create a virtual interface. In the following
example, the interface ctunnel command is used to create the virtual interface.

Examples The following example configures a CTunnel from one router to another and shows the CTunnel
destination set to 49.0001.1111.1111.1111.00:
interface ctunnel 301
ip address 10.0.0.3 255.255.255.0
ctunnel destination 49.0001.1111.1111.1111.00

Related Commands Command Description

clns routing Enables routing of CLNS packets.
ctunnel destination Configures the destination parameter for a CLNS tunnel.
debug ctunnel Displays debug messages for the IP over a CLNS Tunnel feature.
ip address Sets a primary or secondary IP address for an interface.
ip routing Enables IP routing.

Cisco IOS ISO CLNS Command Reference

P5R-69
 Cisco IOS ISO CLNS Commands
ip domain-lookup nsap

ip domain-lookup nsap
To allow Domain Name System (DNS) queries for CLNS addresses, use the ip domain-lookup nsap
command in global configuration mode. To disable this function, use the no form of this command.

ip domain-lookup nsap

no ip domain-lookup nsap

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines With both IP and ISO CLNS enabled on a router, this feature allows you to discover a CLNS address
without having to specify a full CLNS address given a host name. This feature is useful for the ISO
CLNS ping EXEC command and when making CLNS Telnet connections.

Examples The following example disables DNS queries of CLNS addresses:

no ip domain-lookup nsap

Related Commands Command Description

ip domain-lookup Enables the IP DNS-based host name-to-address translation.
ping (privileged) Diagnoses basic network connectivity on AppleTalk, CLNS, DECnet, IP,
or Novell IPX networks.
redistribute Redistributes routing information from one domain into another routing
(ISO CLNS) domain.

Cisco IOS ISO CLNS Command Reference

P5R-70
 Cisco IOS ISO CLNS Commands
isis adjacency-filter

isis adjacency-filter
To filter the establishment of Intermediate System-to-Intermediate System (IS-IS) adjacencies, use the
isis adjacency-filter command in interface configuration mode. To disable filtering of the establishment
of IS-IS adjacencies, use the no form of this command.

isis adjacency-filter name [match-all]

no isis adjacency-filter name [match-all]

Syntax Description name Name of the filter set or expression to apply.

match-all (Optional) All NSAP addresses must match the filter in order to accept the
adjacency. If not specified (the default), only one address need match the
filter in order for the adjacency to be accepted.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Filtering is performed by building NSAP addresses out of incoming IS-IS hello packets by combining
each area address in the hello with the system ID. Each of these NSAP addresses is then passed through
the filter. If any one NSAP matches, the filter is considered “passed,” unless the match-all keyword was
specified, in which case all addresses must pass. The functionality of the match-all keyword is useful in
performing “negative tests,” such as accepting an adjacency only if a particular address is not present.
Filtering is performed on full NSAP addresses. If filtering should only be performed on system IDs, or
any other substring of the full NSAP address, the wildcard matching capabilities of filter sets should be
used to ignore the insignificant portions of the NSAP addresses.
Filter sets and expressions are described in this manual in the descriptions for the clns filter-expr, clns
filter-set, and clns template-alias global configuration commands.

Examples The following example builds a filter that accepts adjacencies with only two systems, based only on their
system IDs:
clns filter-set ourfriends ...0000.0c00.1234.**
clns filter-set ourfriends ...0000.0c00.125a.**
!
interface ethernet 0
isis adjacency-filter ourfriends

Cisco IOS ISO CLNS Command Reference

P5R-71
 Cisco IOS ISO CLNS Commands
isis adjacency-filter

Related Commands Command Description

clns adjacency-filter Filters the establishment of CLNS ES and IS adjacencies.
clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.
clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.
clns template-alias Builds a list of alphanumeric aliases of CLNS address templates for use in
the definition of CLNS filter sets.
iso-igrp Filters the establishment of ISO IGRP adjacencies.
adjacency-filter

Cisco IOS ISO CLNS Command Reference

P5R-72
 Cisco IOS ISO CLNS Commands
iso-igrp adjacency-filter

iso-igrp adjacency-filter
To filter the establishment of ISO IGRP adjacencies, use the iso-igrp adjacency-filter command in
interface configuration mode. To disable filtering of the establishment of ISO IGRP adjacencies, use the
no form of this command.

iso-igrp adjacency-filter name

no iso-igrp adjacency-filter name

Syntax Description name Name of the filter set or expression to apply.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Filtering is performed on full NSAP addresses. If filtering should only be performed on system IDs, or
any other substring of the full NSAP address, the wildcard matching capabilities of filter sets should be
used to ignore the insignificant portions of the NSAP addresses.
For descriptions of filter sets and expressions, refer to the clns filter-expr, clns filter-set, and clns
template-alias global configuration commands in this chapter.

Examples The following example builds a filter that accepts adjacencies with only two systems, based only on their
system IDs:
clns filter-set ourfriends ...0000.0c00.1234.**
clns filter-set ourfriends ...0000.0c00.125a.**
!
interface ethernet 0
iso-igrp adjacency-filter ourfriends

Related Commands Command Description

clns adjacency-filter Filters the establishment of CLNS ES and IS adjacencies.
clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.
clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.

Cisco IOS ISO CLNS Command Reference

P5R-73
 Cisco IOS ISO CLNS Commands
iso-igrp adjacency-filter

Command Description
clns template-alias Builds a list of alphanumeric aliases of CLNS address templates for use in
the definition of CLNS filter sets.
isis adjacency-filter Filters the establishment of IS-IS adjacencies.

Cisco IOS ISO CLNS Command Reference

P5R-74
 Cisco IOS ISO CLNS Commands
lsp-mtu (ISO CLNS)

lsp-mtu (ISO CLNS)

To set the maximum transmission unit (MTU) size of Intermediate System-to-Intermediate System
(IS-IS) link-state packets (LSPs), use the lsp-mtu command in router configuration mode. To disable
this function, use the no form of this command.

lsp-mtu size

no lsp-mtu

Syntax Description size Maximum packet size in bytes. The size must be less than or equal to the
smallest MTU of any link in the network. The default size is 1497 bytes.

Defaults 1497 bytes

Command Modes Router configuration

Command History Release Modification

10.3 This command was introduced.

Usage Guidelines Under normal conditions, the default MTU size should be sufficient. However, if the MTU of a link is
below 1500 bytes, the link-state packet MTU must be lowered accordingly on each router in the network.
If this is not done, routing becomes unpredictable.

Note This rule applies for all routers in a network. If any link in the network has a reduced MTU, all routers
must be changed, not just the routers directly connected to the link.

Caution The CLNS MTU of a link (which is the applicable value for IS-IS, even if it is being used to route
IP) may differ from the IP MTU. To be certain about a link MTU as it pertains to IS-IS, use the show
clns interface command to display the value.

Examples The following example sets the MTU size to 1300 bytes:
router isis
lsp-mtu 1300

Related Commands Command Description

clns mtu Sets the MTU packet size for the interface.
mtu Adjusts the maximum packet size or MTU size.

Cisco IOS ISO CLNS Command Reference

P5R-75
 Cisco IOS ISO CLNS Commands
match clns address

match clns address

To define the match criterion, use the match clns address command in route-map configuration mode.
Routes that have a network address matching one or more of the names—and that satisfy all other
defined match criteria—will be redistributed. To remove the match criterion, use the no form of this
command.

match clns address name [name...name]

no match clns address name [name...name]

Syntax Description name Name of a standard access list, filter set, or expression.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met. The no route-map command deletes
the route map.
The match route-map configuration command has multiple formats. The match commands may be
given in any order, and all defined match criteria must be satisfied to cause the route to be redistributed
according to the set actions given with the set commands. The no forms of the match commands remove
the specified match criteria.

Examples In the following configuration, an ISO IGRP-learned route with a prefix 49.0001.0002 will be
redistributed if it satisfies the CLNS address matching criterion:
router isis
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match clns address ourprefix
clns filter-set ourprefix permit 49.0001.0002...

Cisco IOS ISO CLNS Command Reference

P5R-76
 Cisco IOS ISO CLNS Commands
match clns address

Related Commands Command Description

match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface Defines the interface match criterion.
(ISO CLNS)
match metric Defines the metric match criterion.
(ISO CLNS)
match route-type Defines the route-type match criterion.
(ISO CLNS)
redistribute (ISO CLNS) Redistributes routing information from one domain into another routing
domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set metric-type Sets the metric type to give redistributed routes.
(ISO CLNS)
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-77
 Cisco IOS ISO CLNS Commands
match clns next-hop

match clns next-hop

To define the next-hop match criterion, use the match clns next-hop command in route-map
configuration mode. Routes that have a next-hop router address matching one of the names—and that
satisfy all other defined match criteria—will be redistributed. To remove the match criterion, use the no
form of this command.

match clns next-hop name [name...name]

no match clns next-hop name [name...name]

Syntax Description name Name of an access list, filter set, or expression.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met. The no route-map command deletes
the route map.
The match route-map configuration command has multiple formats. The match commands may be
given in any order, and all defined match criteria must be satisfied to cause the route to be redistributed
according to the set actions given with the set commands. The no forms of the match commands remove
the specified match criteria.

Examples In the following configuration, an ISO IGRP-learned route with a prefix 49.0001.0002 will be
redistributed if it satisfies the CLNS next-hop matching criterion:
router isis
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match clns next-hop ourprefix
clns filter-set ourprefix permit 49.0001.0002...

Cisco IOS ISO CLNS Command Reference

P5R-78
 Cisco IOS ISO CLNS Commands
match clns next-hop

Related Commands Command Description

match clns address Defines the match criterion.
match clns route-source Defines the route-source match criterion.
match interface Defines the interface match criterion.
(ISO CLNS)
match metric Defines the metric match criterion.
(ISO CLNS)
match route-type Defines the route-type match criterion.
(ISO CLNS)
redistribute Redistributes routing information from one domain into another routing
(ISO CLNS) domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set metric-type Sets the metric type to give redistributed routes.
(ISO CLNS)
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-79
 Cisco IOS ISO CLNS Commands
match clns route-source

match clns route-source

To define the route-source match criterion, use the match clns route-source command in route-map
configuration mode. Routes that have been advertised by routers at the address specified by the
name—and that satisfy all other defined match criteria—will be redistributed. To remove the specified
match criterion, use the no form of this command.

match clns route-source name [name...name]

no match clns route-source name [name...name]

Syntax Description name Name of access list, filter set, or expression.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met. The no route-map command deletes
the route map.
The match route-map configuration command has multiple formats. The match commands may be
given in any order, and all defined match criteria must be satisfied to cause the route to be redistributed
according to the set actions given with the set commands. The no forms of the match commands remove
the specified match criteria.

Examples In the following configuration, an ISO IGRP-learned route with a prefix 49.0001.0002 will be
redistributed if it satisfies the CLNS route-source matching criterion:
router isis
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match clns route-source ourprefix
clns filter-set ourprefix permit 49.0001.0002...

Cisco IOS ISO CLNS Command Reference

P5R-80
 Cisco IOS ISO CLNS Commands
match clns route-source

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match interface Defines the interface match criterion.
(ISO CLNS)
match metric Defines the metric match criterion.
(ISO CLNS)
match route-type Defines the route-type match criterion.
(ISO CLNS)
redistribute Redistributes routing information from one domain into another routing
(ISO CLNS) domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set metric-type Sets the metric type to give redistributed routes.
(ISO CLNS)
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-81
 Cisco IOS ISO CLNS Commands
match interface (ISO CLNS)

match interface (ISO CLNS)

To define the interface match criterion, use the match interface command in route-map configuration
mode. Routes that have the next hop out one of the interfaces specified—and that satisfy all other defined
match criteria—will be redistributed. To remove the specified match criterion, use the no form of this
command.

match interface type number [type number...type number]

no match interface type number [type number...type number]

Syntax Description type Interface type.

number Interface number.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met. The no route-map command deletes
the route map.
The match route-map configuration command has multiple formats. The match commands may be
given in any order, and all defined match criteria must be satisfied to cause the route to be redistributed
according to the set actions given with the set commands. The no forms of the match commands remove
the specified match criteria.

Examples In the following configuration, an ISO IGRP-learned route with a prefix 49.0001.0002 will be
redistributed if it satisfies the interface (ISO CLNS) matching criterion:
router isis
redistribute rip route-map ourmap
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match interface ethernet2

Cisco IOS ISO CLNS Command Reference

P5R-82
 Cisco IOS ISO CLNS Commands
match interface (ISO CLNS)

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface Defines the route-source match criterion.
(ISO CLNS)
match metric Defines the metric match criterion.
(ISO CLNS)
match route-type Defines the route-type match criterion.
(ISO CLNS)
redistribute Redistributes routing information from one domain into another routing
(ISO CLNS) domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric-type Sets the metric type to give redistributed routes.
(ISO CLNS)
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-83
 Cisco IOS ISO CLNS Commands
match metric (ISO CLNS)

match metric (ISO CLNS)

To define the metric match criterion, use the match metric command in route-map configuration mode.
Routes that have the specified metric—and satisfy all other defined match criteria—will be redistributed.
To remove the specified match criterion, use the no form of this command.

match metric metric-value

no match metric metric-value

Syntax Description metric-value Route metric. This can be an Interior Gateway Routing Protocol (IGRP)
five-part metric.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met. The no route-map command deletes
the route map.
The match route-map configuration command has multiple formats. The match commands may be
given in any order, and all defined match criteria must be satisfied to cause the route to be redistributed
according to the set actions given with the set commands. The no forms of the match commands remove
the specified match criteria.

Examples In the following configuration, an ISO IGRP-learned route with a prefix 49.0001.0002 will be
redistributed if it satisfies the metric (ISO CLNS) matching criterion:
router isis
redistribute rip route-map ourmap
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match metric 26795
clns filter-set ourprefix permit 49.0001.0002...

Cisco IOS ISO CLNS Command Reference

P5R-84
 Cisco IOS ISO CLNS Commands
match metric (ISO CLNS)

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface Defines the route-source match criterion.
(ISO CLNS)
match route-type Defines the route-type match criterion.
(ISO CLNS)
redistribute Redistributes routing information from one domain into another routing
(ISO CLNS) domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric-type Sets the metric type to give redistributed routes.
(ISO CLNS)
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-85
 Cisco IOS ISO CLNS Commands
match route-type (ISO CLNS)

match route-type (ISO CLNS)

To define the route-type match criterion, use the match route-type command in route-map configuration
mode. Routes that have the specified route type—and satisfy all other defined match criteria—will be
redistributed. To remove the specified match criterion, use the no form of this command.

match route-type {level-1 | level-2}

no match route-type {level-1 | level-2}

Syntax Description level-1 IS-IS Level 1 routes.

level-2 IS-IS Level 2 routes.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met. The no route-map command deletes
the route map.
The match route-map configuration command has multiple formats. The match commands may be
given in any order, and all defined match criteria must be satisfied to cause the route to be redistributed
according to the set actions argument given with the set commands. The no forms of the match
commands remove the specified match criteria.

Examples In the following configuration, an ISO IGRP-learned route with a prefix 49.0001.0002 will be
redistributed if it satisfies the route-type (ISO CLNS) matching criterion:
router isis
redistribute rip route-map ourmap
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match route-type level-2
clns filter-set ourprefix permit 49.0001.0002...

Cisco IOS ISO CLNS Command Reference

P5R-86
 Cisco IOS ISO CLNS Commands
match route-type (ISO CLNS)

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface Defines the route-source match criterion.
(ISO CLNS)
match metric Defines the metric match criterion.
(ISO CLNS)
redistribute (ISO CLNS) Redistributes routing information from one domain into another routing
domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric (ISO CLNS) Specifies the routing level of routes to be advertised into a specified area
of the routing domain.
set metric-type Sets the metric type to give redistributed routes.
(ISO CLNS)
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-87
 Cisco IOS ISO CLNS Commands
metric weights (ISO CLNS)

metric weights (ISO CLNS)

To specify different metrics for the ISO IGRP routing protocol on CLNS, use the metric weights
command in router configuration mode. This command allows you to configure the metric constants
used in the ISO IGRP composite metric calculation of reliability and load. To return the five k arguments
to their default values, use the no form of this command.

metric weights qos k1 k2 k3 k4 k5

no metric weights

Syntax Description qos QoS defines transmission quality and availability of service. The argument
must be 0, the default metric.
k1, k2, k3, k4, k5 Values that apply to ISO IGRP for the default metric QoS. The k values are
metric constants used in the ISO IGRP equation that converts an IGRP
metric vector into a scalar quantity. They are numbers from 0 to 127; higher
numbers mean a greater multiplier effect.

Defaults qos: 0
k1: 1
k2: 0
k3: 1
k4: 0
k5: 0

Command Modes Router configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Two additional ISO IGRP metrics can be configured. These are the bandwidth and delay associated with
an interface.

Note Using the bandwidth and delay interface configuration commands to change the values of the ISO
IGRP metrics also changes the values of IP IGRP metrics.

By default, the IGRP composite metric is a 24-bit quantity that is a sum of the segment delays and the
lowest segment bandwidth (scaled and inverted) for a given route. For a network of homogeneous media,
this metric reduces to a hop count. For a network of mixed media (FDDI, Ethernet, and serial lines
running from 9600 bps to T1 rates), the route with the lowest metric reflects the most desirable path to
a destination.
Use this command to alter the default behavior of IGRP routing and metric computation and allow the
tuning of the IGRP metric calculation for QoS.

Cisco IOS ISO CLNS Command Reference

P5R-88
 Cisco IOS ISO CLNS Commands
metric weights (ISO CLNS)

If k5 equals 0, the composite IGRP metric is computed according to the following formula:
metric = [K1 * bandwidth + (K2 * bandwidth) / (256 - load) + K3 * delay]

If k5 does not equal zero, the following additional operation is done:

metric = metric * [K5 / (reliability + K4)]

The default version of IGRP has both k1 and k3 equal to 1, and k2, k4, and k5 equal to 0.
Delay is in units of 10 microseconds. This gives a range of 10 microseconds to 168 seconds. A delay of
all ones indicates that the network is unreachable.
Bandwidth is inverse minimum bandwidth of the path in bits per second scaled by a factor of 10 e10. The
range is 1200 bps to 10 Gbps.
Table 1 lists the default values used for several common media.

Table 1 Bandwidth Values by Media Type

Media Type Delay Bandwidth

Satellite 200,000 (2 sec) 20 (500 Mbit)
Ethernet 100 (1 ms) 1,000
1.544 Mbps 2000 (20 ms) 6,476
64 kbps 2000 156,250
56 kbps 2000 178,571
10 kbps 2000 1,000,000
1 kbps 2000 10,000,000

Reliability is given as a fraction of 255. That is, 255 is 100 percent reliability or a perfectly stable link.
Load is given as a fraction of 255. A load of 255 indicates a completely saturated link.

Examples The following example sets all five metric constants:

router iso-igrp
metric weights 0 2 0 1 0 0

Related Commands Command Description

bandwidth (interface) Sets a bandwidth value for an interface.
delay Sets a delay value for an interface.

Cisco IOS ISO CLNS Command Reference

P5R-89
 Cisco IOS ISO CLNS Commands
redistribute (ISO CLNS)

redistribute (ISO CLNS)

To redistribute routes from one routing domain into another routing domain, use the redistribute
command in router configuration mode. To disable redistribution, or to disable any of the specified
keywords, use the no form of this command.

redistribute protocol [tag] [route-map map-tag]

no redistribute protocol [tag] [route-map map-tag] static [clns | ip]

Syntax Description protocol Type of other routing protocol that is to be redistributed as a source of routes
into the current routing protocol being configured. The keywords supported
are iso-igrp, isis, and static.
tag (Optional) Meaningful name for a routing process.
route-map map-tag (Optional) Route map should be interrogated to filter the importation of
routes from this source routing protocol to the current routing protocol. If not
specified, all routes are redistributed. If this keyword is specified, but no
route map tags are listed, no routes will be imported. The argument map-tag
is the identifier of a configured route map.
static Keyword static is used to redistribute static routes. When used without the
optional keywords, Cisco IOS software injects any OSI static routes into an
OSI domain.
clns (Optional) Keyword clns is used when redistributing OSI static routes into
an IS-IS domain.
ip (Optional) Keyword ip is used when redistributing IP into an IS-IS domain.

Defaults Disabled, except for static routes, which by default are redistributed into IS-IS routing domains but are
not redistributed into ISO IGRP domains. The keyword clns is the default with the keyword static.

Command Modes Router configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines When used with IS-IS, the redistribute command causes the routes learned by the routing process tag
to be advertised in the IS-IS routing process. Static routes are always redistributed into IS-IS unless a no
redistribute static command is performed. Redistribution only occurs for Level 2 routing.
You can specify more than one IS-IS process per router. Cisco IOS Release 12.1 provides multi-area
support where each IS-IS process can handle a separate level-1 area. To create more than one level-1
IS-IS routing process, use the clns router isis command in interface configuration mode. You must use
the area tag argument for multiarea IS-IS configuration, in order to define a meaningful name for each
routing process. See the clns router isis command earlier in this chapter for more information.

Cisco IOS ISO CLNS Command Reference

P5R-90
 Cisco IOS ISO CLNS Commands
redistribute (ISO CLNS)

When used with ISO IGRP, if you have a router that is in two routing domains, you might want to
redistribute routing information between the two domains. The redistribute router configuration
command configures which routes are redistributed into the ISO IGRP domain. It is not necessary to use
redistribution between areas.
The tag argument must be unique among all CLNS router processes for a given router. This tag should
be the same as defined for the routing process in the router iso-igrp global configuration command.
Static routes are only redistributed into ISO IGRP when a redistribute static command is entered. The
default is to not redistribute static routes into ISO IGRP. Only the router that injects the static route needs
to have a redistribute static command defined. This command is needed only when you run ISO IGRP.

Examples The following example illustrates redistribution of ISO IGRP routes of Michigan and ISO IGRP routes
of Ohio into the IS-IS area tagged USA:
router isis USA
redistribute iso-igrp Michigan
redistribute iso-igrp Ohio

The following example illustrates redistribution of IS-IS routes of France and ISO IGRP routes of
Germany into the ISO IGRP area tagged Backbone:
router iso-igrp Backbone
redistribute isis France
redistribute iso-igrp Germany

In the following example, the router advertises any static routes it knows about in the Chicago domain:
router iso-igrp Chicago
redistribute static

Related Commands Command Description

route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.

Cisco IOS ISO CLNS Command Reference

P5R-91
 Cisco IOS ISO CLNS Commands
route-map (ISO CLNS)

route-map (ISO CLNS)

To define the conditions for redistributing routes from one routing protocol into another, use the
route-map command in global configuration mode. To delete the route map, use the no form of this
command.

route-map map-tag {permit | deny} sequence-number

no route-map map-tag {permit | deny} sequence-number

Syntax Description map-tag Meaningful name for the route map. The redistribute command uses this
name to reference this route map. Multiple route-maps can share the same
map tag name. Can either be an expression or a filter set.
permit If the match criteria are met for this route map, and permit is specified, the
route is redistributed as controlled by the set actions. If the match criteria are
not met, and permit is specified, the next route map with the same map-tag
is tested. If a route passes none of the match criteria for the set of route maps
sharing the same name, it is not redistributed by that set.
deny If the match criteria are met for the route map, and deny is specified, the
route is not redistributed, and no further route maps sharing the same map
tag name will be examined.
sequence-number Number that indicates the position a new route map is to have in the list of
route maps already configured with the same name. If given with the no form
of this command, it specifies the position of the route map that should be
deleted.

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the set actions—the particular redistribution actions
to perform if the criteria enforced by the match commands are met.

Cisco IOS ISO CLNS Command Reference

P5R-92
 Cisco IOS ISO CLNS Commands
route-map (ISO CLNS)

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface (ISO CLNS) Defines the interface match criterion.
redistribute (ISO CLNS) Redistributes routing information from one domain into another
routing domain.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified
area of the routing domain.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set metric-type (ISO CLNS) Sets the metric type to give redistributed routes.
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-93
 Cisco IOS ISO CLNS Commands
router iso-igrp

router iso-igrp
To identify the area that the router will work in and let it know that it will be routing dynamically using
the ISO IGRP protocol, use the router iso-igrp command in global configuration mode. To disable ISO
IGRP routing for the system, use the no form of this command with the appropriate tag.

router iso-igrp [tag]

no router iso-igrp [tag]

Syntax Description tag (Optional) Meaningful name for a routing process. For example, you could
define a routing process named Finance for the Finance department, and
another routing process named Marketing for the Marketing department. If
not specified, a null tag is assumed. The tag argument must be unique among
all CLNS router processes for a given router.

Defaults Disabled

Command Modes Global configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Creating a name for a routing process means that you use names when configuring routing. You can
specify up to ten ISO IGRP processes.

Examples The following example specifies a router in Manufacturing. The command must be typed on one line.
router iso-igrp Manufacturing

Related Commands Command Description

clns router iso-igrp Specifies ISO IGRP routing on a specified interface.
redistribute Redistributes routing information from one domain into another routing
(ISO CLNS) domain.

Cisco IOS ISO CLNS Command Reference

P5R-94
 Cisco IOS ISO CLNS Commands
set level (ISO CLNS)

set level (ISO CLNS)

To specify the routing level of routes to be advertised into a specified area of the routing domain, use the
set level command in route-map configuration mode. To disable advertising the specified routing level
into a specified area, use the no form of this command.

set level {level-1 | level-2 | level-1-2}

no set level {level-1 | level-2 | level-1-2}

Syntax Description level-1 Inserted in IS-IS Level 1 link-state PDUs.

level-2 Inserted in IS-IS Level 2 link-state PDUs. For IS-IS destinations, level-2 is
the default.
level-1-2 Inserted into both Level 1 and Level 2 IS-IS link-state PDUs.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the redistribution set actions—the particular
redistribution actions to perform if the criteria enforced by the match commands are met. When all
match criteria are met, all set actions are performed. The no route-map command deletes the route map.

Examples Given the following configuration, a RIP-learned route for network 160.89.0.0 and an ISO IGRP-learned
route with prefix 49.0001.0002 will be redistributed into an IS-IS Level 2 link-state PDU with metric 5:
router isis
redistribute rip route-map ourmap
redistribute iso-igrp remote route-map ourmap
route-map ourmap permit
match ip address 1
match clns address ourprefix
set metric 5
set level level-2
access-list 1 permit 160.89.0.0 0.0.255.255
clns filter-set ourprefix permit 49.0001.0002...

Cisco IOS ISO CLNS Command Reference

P5R-95
 Cisco IOS ISO CLNS Commands
set level (ISO CLNS)

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface Defines the interface match criterion.
(ISO CLNS)
match metric (ISO CLNS) Defines the metric match criterion.
match route-type Sets the metric type to give redistributed routes.
(ISO CLNS)
redistribute (ISO CLNS) Redistributes routing information from one domain into another
routing domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing
protocol into another.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set metric-type (ISO CLNS) Sets the metric type to give redistributed routes.
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-96
 Cisco IOS ISO CLNS Commands
set metric (ISO CLNS)

set metric (ISO CLNS)

To change the metric value used to redistribute routes, use the set metric command in route-map
configuration mode. To reinstate the original metric values, use the no form of this command.

set metric metric-value

no set metric metric-value

Syntax Description metric-value Route metric. This can be an IGRP five-part metric.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the redistribution set actions—the particular
redistribution actions to perform if the criteria enforced by the match commands are met. When all
match criteria are met, all set actions are performed. The no route-map command deletes the route map.

Examples Given the following configuration, a RIP-learned route for network 160.89.0.0 and an ISO IGRP-learned
route with prefix 49.0001.0002 will be redistributed into an IS-IS Level 2 link-state PDU with metric 5:
router isis
redistribute rip route-map ourmap
redistribute iso-igrp remote route-map ourmap
!
route-map ourmap permit
match ip address 1
match clns address ourprefix
set metric 5
set level level-2
!
access-list 1 permit 160.89.0.0 0.0.255.255
clns filter-set ourprefix permit 49.0001.0002...

Related Commands

Cisco IOS ISO CLNS Command Reference

P5R-97
 Cisco IOS ISO CLNS Commands
set metric (ISO CLNS)

Command Description
match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface (ISO CLNS) Defines the interface match criterion.
match metric (ISO CLNS) Defines the metric match criterion.
match route-type (ISO CLNS) Sets the metric type to give redistributed routes.
redistribute (ISO CLNS) Redistributes routing information from one domain into another
routing domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing
protocol into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified
area of the routing domain.
set metric-type (ISO CLNS) Sets the metric type to give redistributed routes.
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-98
 Cisco IOS ISO CLNS Commands
set metric-type (ISO CLNS)

set metric-type (ISO CLNS)

To set the metric type for redistributed routes, use the set metric-type command in route-map
configuration mode. To reinstate the original metric type, use the no form of this command.

set metric-type {internal | external}

no set metric-type {internal | external}

Syntax Description internal IS-IS internal metric.

external IS-IS external metric.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the redistribution set actions—the particular
redistribution actions to perform if the criteria enforced by the match commands are met. When all
match criteria are met, all set actions are performed. The no route-map command deletes the route map.

Examples The following example sets the metric type of the destination protocol to IS-IS internal metric:
route-map map-type
set metric-type internal

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface (ISO CLNS) Defines the interface match criterion.
redistribute (ISO CLNS) Redistributes routing information from one domain into another
routing domain.
match clns address Defines the match criterion.

Cisco IOS ISO CLNS Command Reference

P5R-99
 Cisco IOS ISO CLNS Commands
set metric-type (ISO CLNS)

Command Description
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface (ISO CLNS) Defines the interface match criterion.
match metric (ISO CLNS) Defines the metric match criterion.
match route-type (ISO CLNS) Sets the metric type to give redistributed routes.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing
protocol into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified
area of the routing domain.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set tag (ISO CLNS) Sets a tag value to associate with the redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-100
 Cisco IOS ISO CLNS Commands
set tag (ISO CLNS)

set tag (ISO CLNS)

To set a tag value to associate with the redistributed routes, use the set tag command in route-map
configuration mode. To revert to redistributing routes without associating a specific tag with them, use
the no form of this command.

set tag tag-value

no set tag tag-value

Syntax Description tag-value Name for the tag. The tag value to associate with the redistributed route. If
not specified, the default action is to forward the tag in the source routing
protocol onto the new destination protocol.

Defaults Disabled

Command Modes Route-map configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Use the route-map global configuration command, and the route-map configuration commands match
and set, to define the conditions for redistributing routes from one routing protocol into another. Each
route-map command has a list of match and set commands associated with it. The match commands
specify the match criteria—the conditions under which redistribution is allowed for the current
route-map command. The set commands specify the redistribution set actions—the particular
redistribution actions to perform if the criteria enforced by the match commands are met. When all
match criteria are met, all set actions are performed. The no route-map command deletes the route map.

Examples The following example sets the tag value of the destination routing protocol to 5:
route-map tag
set tag 5

Related Commands Command Description

match clns address Defines the match criterion.
match clns next-hop Defines the next-hop match criterion.
match clns route-source Defines the route-source match criterion.
match interface (ISO CLNS) Defines the interface match criterion.
redistribute (ISO CLNS) Redistributes routing information from one domain into another
routing domain.

Cisco IOS ISO CLNS Command Reference

P5R-101
 Cisco IOS ISO CLNS Commands
set tag (ISO CLNS)

Command Description
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing
protocol into another.
set level (ISO CLNS) Specifies the routing level of routes to be advertised into a specified
area of the routing domain.
set metric (ISO CLNS) Sets the metric value to give the redistributed routes.
set metric-type (ISO CLNS) Sets the metric type to give redistributed routes.

Cisco IOS ISO CLNS Command Reference

P5R-102
 Cisco IOS ISO CLNS Commands
show clns

show clns
To display information about the CLNS network, use the show clns command in EXEC mode.

show clns

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show clns command:
Router# show clns

Global CLNS Information:

2 Interfaces Enabled for CLNS
NET: 39.0004.0030.0000.0C00.224D.00
NET: 39.0003.0020.0000.0C00.224D.00
Configuration Timer: 60, Default Holding Timer: 300, Packet Lifetime 64
ERPDU's requested on locally generated packets
Intermediate system operation enabled (forwarding allowed)
ISO IGRP level-1 Router: remote
Routing for Domain: 39.0003, Area: 0020
ISO IGRP level-2 Router: DOMAIN_remote
Routing for Domain: 39.0003
IS-IS level-1-2 Router:
Routing for Area: 39.0004.0030

Table 2 describes significant fields shown in the display.

Table 2 show clns Field Descriptions

Field Description
2 Interfaces Enabled for CLNS Indicates how many interfaces have the CLNS protocol
enabled.
NET: First of two NETs for this router.
39.0004.0030.0000.0C00.224D.00
Configuration Timer: 60 Displays the interval (in seconds) after which the router sends
out IS hello packets.
Default Holding Timer: 300 Length of time (in seconds) hello packets are remembered.
Packet Lifetime 64 Default value used in packets sourced by this router.
ERPDUs requested on locally Indicates whether ERPDUs are requested for packets sourced
generated packets by the router.

Cisco IOS ISO CLNS Command Reference

P5R-103
 Cisco IOS ISO CLNS Commands
show clns

Table 2 show clns Field Descriptions (continued)

Field Description
Intermediate system operation Indicates whether this router is configured to be an ES or an IS.
enabled (forwarding allowed)
ISO IGRP level-1 Router: remote Specifies what CLNS routing type (ISO IGRP or IS-IS) and
what routing level (Level 1, Level 2, or both) is enabled on the
router.
Routing for Domain: 39.0003, Specifies the domain (39.0003) and area (0020) for which this
Area: 0020 CLNS routing type and routing level is enabled.
IS-IS level-1-2 Router: Specifies that IS-IS is running in this router. Its tag is null. It is
running Level 1 and Level 2.
Routing for Area: 39.0004.0030 Specifies the IS-IS area this router is in.

Cisco IOS ISO CLNS Command Reference

P5R-104
 Cisco IOS ISO CLNS Commands
show clns cache

show clns cache

To display the CLNS route cache, use the show clns cache command in EXEC mode. The cache contains
an entry for each destination that recently has been fast-switched. The output of this command includes
entries showing each destination for which the router has switched a packet in the recent past. This
includes the router itself.

show clns cache [delay-parameters | invalidations]

Syntax Description delay-parameters (Optional) Current settings for delays when entries are invalidated in the
CLNS route cache.
invalidations (Optional) When specified, shows the last time each function purged the
CLNS route cache.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show clns cache command:
Router# show clns cache

CLNS routing cache version 433

Destination -> Next hop @ Interface: SNPA Address => Rewrite / Length
[42] *39.0004.0040.0000.0C00.2D55.00 ISOLATOR
-> 0000.0C00.2D55 @ Ethernet0/1: 0000.0c00.6fa5

Table 3 describes significant fields shown in the display.

Table 3 show clns cache Field Descriptions

Field Description
CLNS routing cache version 433 Number identifying this particular CLNS routing cache.
Destination -> Destination NSAP for the packet.
Next hop Next hop system ID used to reach the destination.
@ Interface: Interface through which the router transmitted the packet.
SNPA Address Address of the subnetwork point of attachment (SNPA) of the
next hop for this destination NSAP.
Rewrite / Length Interface encapsulation data and length of the cache entry
that the cache must overwrite onto the outgoing frame prior
to sending it. If the rewrite length of the cache entry is zero,
this field will not be displayed.
[42] Cache location for this entry.

Cisco IOS ISO CLNS Command Reference

P5R-105
 Cisco IOS ISO CLNS Commands
show clns cache

Table 3 show clns cache Field Descriptions (continued)

Field Description
1
*39.0004.0040.0000.0C00.2D55.00 Destination NSAP address.
ISOLATOR Destination host name.
0000.0C00.2D55 System ID of the next-hop router.
Ethernet0/1 Interface through which the router transmitted the packet.
000.0c00.6fa5 SNPA for the next-hop router through the output interface.
1. A leading asterisk (*) indicates that the entry is an allowable value.

The following is sample output from the show clns cache delay-parameters command:
Router#
Minimum invalidation interval 2 seconds,
Maximum invalidation interval 5 seconds,
Quiet interval 3 seconds,
Threshold 0 requests
Invalidation rate 3 in last second, 3 in last 3 seconds

Table 4 describes significant fields shown in the display.

Table 4 show clns cache delay-parameters Field Descriptions

Field Description
Minimum invalidation interval Minimum time (in seconds) between invalidation
request and actual invalidation.
Maximum Invalidation interval Maximum time (in seconds) between invalidation
request and actual invalidation.
Quiet interval Length of time (in seconds) before invalidation.
Threshold Maximum number of invalidations considered to be
quiet.
Invalidation rate Number of invalidations (route cache purges) per
second.

The following is sample output from the show clns cache invalidations command:
Router#
Caller Count Last Invalidation
clns_fastsetup 3 20:55:56
clns_route_update 23 20:56:44
clns_route_adjust 2 20:55:52
isis_compute_spt 2017 00:10:13
delete_adjacency 9 1d19h
clns_ager 11 1d19h

Table 5 describes significant fields shown in the display.

Cisco IOS ISO CLNS Command Reference

P5R-106
 Cisco IOS ISO CLNS Commands
show clns cache

Table 5 show clns cache invalidations Field Descriptions

Field Description
Caller Lists the names of the functions that have purged the
CLNS route cache.
Count Number of times the function has invalidated the
CLNS route cache.
Last invalidation The last time the function invalidated the CLNS route
cache.

Related Commands Command Description

clear clns cache Clears and reinitializes the CLNS routing cache.

Cisco IOS ISO CLNS Command Reference

P5R-107
 Cisco IOS ISO CLNS Commands
show clns es-neighbors

show clns es-neighbors

To list the ES neighbors that this router knows about, use the show clns es-neighbors command in EXEC
mode.

show clns area-tag es-neighbors [type number] [detail]

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among all
IP or Connectionless Network Service (CLNS) router processes for a given
router. If an area tag is not specified, a null tag is assumed and the process is
referenced with a null tag. If an area tag is specified, output is limited to the
specified area.
type (Optional) Interface type.
number (Optional) Interface number.
detail (Optional) When specified, the areas associated with the end systems are
displayed. Otherwise, a summary display is provided.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.
12.0(5)T The area-tag argument was added.

Examples The following is sample output from the show clns es-neighbors command when Ethernet interface 0
is specified:
Router# show clns es-neighbors ethernet0

System Id Interface State Type Format

0800.2B14.060E Ethernet0 Up ES Phase V
0800.2B14.0528 Ethernet0 Up ES Phase V

Table 6 describes the significant fields shown in the display.

Table 6 show clns es-neighbors Field Descriptions

Field Descriptions
System Id Identification value of the system.
Interface Interface on which the router was discovered.
State Adjacency state. Up and Init are the states. See the show clns
neighbors description.

Cisco IOS ISO CLNS Command Reference

P5R-108
 Cisco IOS ISO CLNS Commands
show clns es-neighbors

Table 6 show clns es-neighbors Field Descriptions (continued)

Field Descriptions
Type Type of neighbor. Only valid value for the show clns es-neighbors
EXEC command is ES.
Format Indicates if the neighbor is either a Phase V (OSI) adjacency or
Phase IV (DECnet) adjacency.

The following is sample output from the show clns es-neighbors detail command:
router# show clns es-neighbors detail

System Id Interface State Type Format

0800.2B14.060E Ethernet0 Up ES Phase V
Area Address(es): 49.0040
0800.2B14.0528 Ethernet0 Up ES Phase V
Area Address(es): 49.0040

Notice that the information displayed in show clns es-neighbors detail output includes everything
shown in show clns es-neighbors output, but it also includes the area addresses associated with the ES
neighbors.

Related Commands Command Description

clear clns es-neighbors Removes ES neighbor information from the adjacency database.
clns es-neighbor Defines all end systems that will be used when you manually specify the
NSAP-to-SNPA mapping.

Cisco IOS ISO CLNS Command Reference

P5R-109
 Cisco IOS ISO CLNS Commands
show clns filter-expr

show clns filter-expr

To display one or all currently defined CLNS filter expressions, use the show clns filter-expr command
in EXEC mode.

show clns filter-expr [name] [detail]

Syntax Description name (Optional) Name of the filter expression to display. If none is specified, all
are displayed.
detail (Optional) When specified, expressions are evaluated down to their most
primitive filter set terms before being displayed.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following displays assume filter expressions have been defined with the following commands.
FRED, BARNEY, WILMA, and BETTY are all filter sets.
clns filter-expr MEN FRED or BARNEY
clns filter-expr WOMEN WILMA or BETTY
clns filter-expr ADULTS MEN or WOMEN

The show clns filter-expr command would yield the following output:
Router# show clns filter-expr

MEN = FRED or BARNEY

WOMEN = WILMA or BETTY
ADULTS = MEN or WOMEN

The show clns filter-expr detail command would yield the following output:
Router# show clns filter-expr detail

MEN = FRED or BARNEY

WOMEN = WILMA or BETTY
ADULTS = (FRED or BARNEY) or (WILMA or BETTY)

Related Commands Command Description

clns filter-expr Combines CLNS filter sets and CLNS address templates to create complex
logical NSAP pattern-matching expressions.

Cisco IOS ISO CLNS Command Reference

P5R-110
 Cisco IOS ISO CLNS Commands
show clns filter-set

show clns filter-set

To display one or all currently defined CLNS filter sets, use the show clns filter-set command in EXEC
mode.

show clns filter-set [name]

Syntax Description name (Optional) Name of the filter set to display. If none is specified, all are
displayed.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following display assumes filter sets have been defined with the following commands:
clns filter-set US-OR-NORDUNET 47.0005...
clns filter-set US-OR-NORDUNET 47.0023...
clns filter-set LOCAL 49.0003...

The following is a sample output from the show clns filter-set command:
Router# show clns filter-set

CLNS filter set US-OR-NORDUNET

permit 47.0005...
permit 47.0023...
CLNS filter set LOCAL
permit 49.0003...

Related Commands Command Description

clns filter-set Builds a list of CLNS address templates with associated permit and deny
conditions for use in CLNS filter expressions.

Cisco IOS ISO CLNS Command Reference

P5R-111
 Cisco IOS ISO CLNS Commands
show clns interface

show clns interface

To list the CLNS-specific information about each interface, use the show clns interface command in
EXEC mode.

show clns interface [type number]

Syntax Description type (Optional) Interface type.

number (Optional) Interface number.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show clns interface command that includes information for
Token Ring and serial interfaces:
Router# show clns interface

TokenRing 0 is administratively down, line protocol is down

CLNS protocol processing disabled
TokenRing 1 is up, line protocol is up
Checksums enabled, MTU 4461, Encapsulation SNAP
ERPDUs enabled, min. interval 10 msec.
RDPDUs enabled, min. interval 100 msec., Addr Mask enabled
Congestion Experienced bit set at 4 packets
CLNS fast switching disabled
DEC compatibility mode OFF for this interface
Next ESH/ISH in 18 seconds
Routing Protocol: ISO IGRP
Routing Domain/Area: <39.0003> <0020>
Serial 2 is up, line protocol is up
Checksums enabled, MTU 1497, Encapsulation HDLC
ERPDUs enabled, min. interval 10 msec.
RDPDUs enabled, min. interval 100 msec., Addr Mask enabled
Congestion Experienced bit set at 4 packets
CLNS fast switching enabled
DEC compatibility mode OFF for this interface
CLNS cluster alias enabled on this interface
Next ESH/ISH in 48 seconds
Routing Protocol: IS-IS
Circuit Type: level-1-2
Level-1 Metric: 10, Priority: 64, Circuit ID: 0000.0C00.2D55.0A
Number of active level-1 adjacencies: 0
Level-2 Metric: 10, Priority: 64, Circuit ID: 0000.0000.0000.00
Number of active level-2 adjacencies: 0
Next IS-IS LAN Level-1 hello in 3 seconds
Next IS-IS LAN Level-2 hello in 3 seconds

Table 7 describes significant fields shown in the display.

Cisco IOS ISO CLNS Command Reference

P5R-112
Cisco IOS ISO CLNS Commands
show clns interface

Table 7 show clns interface Field Descriptions

Field Description
TokenRing 0 is (First interface). Shown to be administratively down with
administratively down, line CLNS disabled.
protocol is down
TokenRing 1 is up, line (Second interface). Shown to be up, and the line protocol is
protocol is up up.
Serial 2 is up, line protocol is (Third interface). Shown to be up, and the line protocol is up.
up
Checksums enabled Can be enabled or disabled.
MTU The number following MTU is the maximum transmission
size for a packet on this interface.
Encapsulation Describes the encapsulation used by CLNP packets on this
interface.
ERPDUs Displays information about the generation of ERPDUs. They
can be either enabled or disabled. If they are enabled, they are
sent out no more frequently than the specified interval.
RDPDUs Provides information about the generation of RDPDUs. They
can be either enabled or disabled. If they are enabled, they are
sent out no more frequently than the specified interval. If the
address mask is enabled, redirects are sent out with an address
mask.
Congestion Experienced Tells when CLNS will turn on the congestion experienced bit.
The default is to turn this bit on when there are more than four
packets in a queue.
CLNS fast switching Displays whether fast switching is supported for CLNS on
this interface.
DEC compatibility mode Indicates whether DEC compatibility has been enabled.
CLNS cluster alias enabled on Indicates that CLNS cluster aliasing has been enabled on this
this interface interface.
Next ESH/ISH Displays when the next ES hello or IS hello is sent on this
interface.
Routing Protocol Lists the areas that this interface is in. In most cases, an
interface will be in only one area.
Circuit type Indicates whether the interface has been configured for local
routing (Level 1), area routing (Level 2), or local and area
routing (Level 1-2).
Remaining fields Last series of fields displays information pertaining to the
ISO CLNS routing protocols enabled on the interface. For
ISO IGRP, the routing domain and area addresses are
specified. For IS-IS, the Level 1 and Level 2 metrics,
priorities, Circuit IDs, and number of active Level 1 and Level
2 adjacencies are specified.

Cisco IOS ISO CLNS Command Reference

P5R-113
 Cisco IOS ISO CLNS Commands
show clns is-neighbors

show clns is-neighbors

To display Intermediate System-to-Intermediate System (IS-IS) related information for IS-IS router
adjacencies, use the show clns is-neighbors command in EXEC mode. Neighbor entries are sorted
according to the area in which they are located.

show clns area-tag is-neighbors [type number] [detail]

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among all
IP or CLNS router processes for a given router. If an area tag is not specified,
a null tag is assumed and the process is referenced with a null tag. If an area
tag is specified, output is limited to the specified area.
type (Optional) Interface type.
number (Optional) Interface number.
detail (Optional) When specified, the areas associated with the intermediate
systems are displayed. Otherwise, a summary display is provided.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show clns is-neighbors command:
Router# show clns is-neighbors

System Id Interface State Type Priority Circuit Id Format

0000.0C00.0C35 Ethernet1 Up L1 64 0000.0C00.62E6.03 Phase V
0800.2B16.24EA Ethernet0 Up L1L2 64/64 0800.2B16.24EA.01 Phase V
0000.0C00.3E51 Serial1 Up L2 0 04 Phase V
0000.0C00.62E6 Ethernet1 Up L1 64 0000.0C00.62E6.03 Phase V

Table 8 describes significant fields shown in the display.

Table 8 show clns is-neighbors Field Descriptions

Field Descriptions
System Id Identification value of the system.
Interface Interface on which the router was discovered.
State Adjacency state. Up and Init are the states. See the show clns
neighbors description.
Type L1, L2, and L1L2 type adjacencies. See the show clns neighbors
description.

Cisco IOS ISO CLNS Command Reference

P5R-114
 Cisco IOS ISO CLNS Commands
show clns is-neighbors

Table 8 show clns is-neighbors Field Descriptions (continued)

Field Descriptions
Priority IS-IS priority that the respective neighbor is advertising. The highest
priority neighbor is elected the designated IS-IS router for the
interface.
Circuit Id Neighbor’s idea of what the designated IS-IS router is for the interface.
Format Indicates if the neighbor is either a Phase V (OSI) adjacency or
Phase IV (DECnet) adjacency.

The following is sample output from the show clns is-neighbors detail command:
Router# show clns is-neighbors detail

System Id Interface State Type Priority Circuit Id Format

0000.0C00.0C35 Ethernet1 Up L1 64 0000.0C00.62E6.03 Phase V
Area Address(es): 47.0004.004D.0001 39.0001
Uptime: 0:03:35
0800.2B16.24EA Ethernet0 Up L1L2 64/64 0800.2B16.24EA.01 Phase V
Area Address(es): 47.0004.004D.0001
Uptime: 0:03:35
0000.0C00.3E51 Serial1 Up L2 0 04 Phase V
Area Address(es): 39.0004
Uptime: 0:03:35
000.0C00.62E6 Ethernet1 Up L1 64 0000.0C00.62E6.03 Phase V
Area Address(es): 47.0004.004D.0001
Uptime: 0:03:35

Notice that the information displayed in show clns is-neighbors detail output includes everything
shown in show clns is-neighbors output, but it also includes the area addresses associated with the IS
neighbors (intermediate-system adjacencies) and how long (uptime) the adjacency has existed.

Related Commands Command Description

clear clns is-neighbors Removes IS neighbor information from the adjacency database.
clns is-neighbor Defines all intermediate systems that will be used when you manually
specify the NSAP-to-SNPA mapping.

Cisco IOS ISO CLNS Command Reference

P5R-115
 Cisco IOS ISO CLNS Commands
show clns neighbor areas

show clns neighbor areas

To display information about Intermediate System-to-Intermediate System (IS-IS) neighbors and the
areas to which they belong, use the show clns neighbor areas command in EXEC mode.

show clns area-tag neighbor areas

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among
all IP or CLNS router processes for a given router. If an area tag is not
specified, a null tag is assumed and the process is referenced with a null tag.
If an area tag is specified, output is limited to the specified area.

Command Modes EXEC

Command History Release Modification

12.0(5)T This command was introduced.

Usage Guidelines Use the show clns neighbor areas command to verify that all expected adjacencies are up with all
neighbors. If they are not, recheck the area addresses specified in both routers. If the router is running
in dual CLNS-IP mode in an area, verify that a valid IP address is configured on each interface in the
area. Consider using the debug isis adjacency command to gather additional information.

Examples The following example shows output when two Level 1 and one Level 2 IS-IS areas are configured.
Router# show clns neighbor areas

System Id Interface Area Name State Holdtime Type Protocol

0000.0000.0009 Tu529 L2BB Up 26 L1L2 IS-IS
0000.0000.0053 Et1 A3253-01 Up 21 L1 IS-IS
0000.0000.0003 Et1 A3253-01 Up 28 L1 IS-IS
0000.0000.0002 Et2 A3253-02 Up 22 L1 IS-IS
0000.0000.0053 Et2 A3253-02 Up 23 L1 IS-IS

Table 9 describes the significant fields shown in the display.

Table 9 show clns neighbor areas Field Descriptions

Field Descriptions
System Id Identification value of the system.
Interface Interface on which the router was discovered.
Area Name Name of the area in which the system is configured.

Cisco IOS ISO CLNS Command Reference

P5R-116
 Cisco IOS ISO CLNS Commands
show clns neighbor areas

Table 9 show clns neighbor areas Field Descriptions (continued)

Field Descriptions
State Adjacency state. Up and Init are the states. See the show clns
neighbors description.
Init System is waiting for an IS-IS hello message.
Up Believes the system is reachable.
Holdtime Number of seconds before this adjacency entry times out.
Type L1, L2, and L1L2 type adjacencies.
ES End-system adjacency either discovered by the ES-IS protocol or
statically configured.
IS Router adjacency either discovered by the ES-IS protocol or statically
configured.
L1 Router adjacency for Level 1 routing only.
L1L2 Router adjacency for Level 1 and Level 2 routing.
L2 Router adjacency for Level 2 only.
Protocol Protocol through which the adjacency was learned. Valid protocol
sources are ES-IS, IS-IS, International Standards Organization Interior
Gateway Routing Protocol (ISO IGRP), static, and DECnet.

Related Commands Command Description

show clns es-neighbors Lists the ES neighbors that this router knows.
show clns is-neighbors Displays IS-IS related information for IS-IS router adjacencies.
show clns neighbors Displays both ES and IS neighbors.

Cisco IOS ISO CLNS Command Reference

P5R-117
 Cisco IOS ISO CLNS Commands
show clns neighbors

show clns neighbors

To display both ES and IS neighbors, use the show clns neighbors command in EXEC mode.

show clns area-tag neighbors [type number] [area] [detail]

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among all
IP or CLNS router processes for a given router. If an area tag is not specified,
a null tag is assumed and the process is referenced with a null tag. If an area
tag is specified, output is limited to the specified area.
type (Optional) Interface type.
number (Optional) Interface number.
area (Optional) When specified, the CLNS multiarea adjacencies are displayed.
detail (Optional) When specified, the area addresses advertised by the neighbor in
the hello messages is displayed. Otherwise, a summary display is provided.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.
12.0(5)T The area and detail keywords were added.

Examples The following is sample output from the show clns neighbors command. This display is a composite of
the show clns es-neighbor and show clns is-neighbor commands.
Router# show clns neighbors

System Id SNPA Interface State Holdtime Type Protocol

0000.0000.0007 aa00.0400.6408 Ethernet0 Init 277 IS ES-IS
0000.0C00.0C35 0000.0c00.0c36 Ethernet1 Up 91 L1 IS-IS
0800.2B16.24EA aa00.0400.2d05 Ethernet0 Up 29 L1L2 IS-IS
0800.2B14.060E aa00.0400.9205 Ethernet0 Up 1698 ES ES-IS
0000.0C00.3E51 *HDLC* Serial1 Up 28 L2 IS-IS
0000.0C00.62E6 0000.0c00.62e7 Ethernet1 Up 22 L1 IS-IS
0A00.0400.2D05 aa00.0400.2d05 Ethernet0 Init 24 IS ES-IS

Table 10 describes the fields shown in the display.

Table 10 show clns neighbors Field Descriptions

Field Description
System Id Six-byte value that identifies a system in an area.
SNPA Subnetwork Point of Attachment. This is the data link address.

Cisco IOS ISO CLNS Command Reference

P5R-118
 Cisco IOS ISO CLNS Commands
show clns neighbors

Table 10 show clns neighbors Field Descriptions (continued)

Field Description
Interface Interface in which the system was learned from.
State State of the ES or IS.
Init System is an IS and is waiting for an IS-IS hello message. IS-IS
regards the neighbor as not adjacent.
Up Believes the ES or IS is reachable.
Holdtime Number of seconds before this adjacency entry times out.
Type The adjacency type. Possible values are as follows:
ES End-system adjacency either discovered via the ES-IS protocol or
statically configured.
IS Router adjacency either discovered via the ES-IS protocol or
statically configured.
L1 Router adjacency for Level 1 routing only.
L1L2 Router adjacency for Level 1 and Level 2 routing.
L2 Router adjacency for Level 2 only.
Protocol Protocol through which the adjacency was learned. Valid protocol
sources are ES-IS, IS-IS, ISO IGRP, Static, and DECnet.

The following is sample output from the show clns neighbors detail command:
Router# show clns neighbors detail

System Id Interface SNPA State Holdtime Type Protocol

0102.5555.0036 Et1/1 0030.80aa.9b81 Up 23 L1 IS-IS
Area Address(es):49.0002
IP Address(es): 175.1.19.36*
Uptime: 00:00:51
0000.0000.0001 Et1/1 0030.9655.201d Up 23 L1L2 IS-IS
Area Address(es): 49.0002
IP Address(es): 172.16.19.22* 10.12.33.54 10.120.33.253
Uptime: 00:25:30

Notice that the information displayed in show clns neighbors detail output includes everything shown
in show clns neighbors output in addition to the area address associated with the IS neighbor and its
uptime. When IP routing is enabled, Integrated-ISIS adds information to the output of the show clns
commands. The show clns neighbors detail command output shows the IP addresses that are defined
for the directly connected interface and an asterik (*) to indicate which IP address is the next-hop.

Related Commands Command Description

clear clns neighbors Removes CLNS neighbor information from the adjacency database.

Cisco IOS ISO CLNS Command Reference

P5R-119
 Cisco IOS ISO CLNS Commands
show clns protocol

show clns protocol

To list the protocol-specific information for each ISO IGRP or Intermediate System-to-Intermediate
System (IS-IS) routing process in the router, use the show clns protocol command in EXEC mode.
There will always be at least two routing processes, a Level 1 and a Level 2, and there can be more.

show clns [domain | area-tag] protocol

Syntax Description domain (Optional) Particular ISO IGRP routing domain.

area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among all
IP or Connectionless Network Service (CLNS) router processes for a given
router. If an area tag is not specified, a null tag is assumed and the process is
referenced with a null tag. If an area tag is specified, output is limited to the
specified area.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show clns protocol command:
Router# show clns protocol

ISO IGRP Level 1 Router: remote

Routing for domain: 39.0003 area: 0020
Sending Updates every 45 seconds. Next due in 11 seconds
Invalid after 135 seconds,
Hold down for 145 seconds
Sending Router Hellos every 17 seconds. Next due in 9 seconds
Invalid after 51 seconds,
IGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0
Interfaces in domain/area:
TokenRing1
ISO IGRP Level 2 Router: DOMAIN_remote
Routing for domain: 39.0003
Redistribute:
isis (Null Tag)
Sending Updates every 45 seconds. Next due in 2 seconds
Invalid after 135 seconds,
Hold down for 145 seconds
Sending Router Hellos every 17 seconds. Next due in 0 seconds
Invalid after 51 seconds,
ISO IGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0
Interfaces in domain/area:

Cisco IOS ISO CLNS Command Reference

P5R-120
Cisco IOS ISO CLNS Commands
show clns protocol

TokenRing1
IS-IS Router: <Null Tag>
System Id: 0000.0C00.224D.00 IS-Type: level-1-2
Manual area address(es):
39.0004.0030
Routing for area address(es):
39.0004.0030
Interfaces supported by IS-IS:
Serial2
Next global update in 530 seconds
Redistributing:
static
iso-igrp (remote)
Distance: 110

Table 11 describes significant fields shown in the display.

Table 11 show clns protocol Field Descriptions

Field Description
ISO IGRP Level 1 Router: Indicates what CLNS routing type is enabled on the router.
(Always ISO IGRP when the fields in this section are
displayed.) Also indicates what routing level (Level 1, Level
2, or both) is enabled on the router.
remote Process tag that has been configured using the router iso-igrp
global configuration command.
Routing for domain: 39.0003 Domain address and area number for Level 1 routing
area: 0020 processes. For Level 2 routing processes, this command lists
the domain address.
Sending Updates every 45 Displays when the next routing updates are sent.
seconds.
Next due in 11 seconds Indicates when the next update is sent.
Invalid after 135 seconds Indicates how long routing updates are to be believed.
Hold down for 145 seconds Indicates how long a route is held down before new
information is to be believed.
Sending Router hellos every Indicates how often Cisco IOS software sends hello packets
17 seconds. Next due in 9 to each other and when the next is due.
seconds
Invalid after 51 seconds Indicates how long a neighbor entry is remembered.
IGRP metric weight K1=1, Displays lists the weights applied to the various components
K2=0, K3=1, K4=0, K5=0 of the metric. These fields are followed by the list of
interfaces in this area.
Interfaces in domain/area: List of interface names for which the router process is
configured.

Table 12 describes significant fields shown in the IS-IS portion of the display.

Cisco IOS ISO CLNS Command Reference

P5R-121
 Cisco IOS ISO CLNS Commands
show clns protocol

Table 12 show clns protocol with IS-IS Field Descriptions

Field Description
IS_IS Router: <Null Tag> Indicates what CLNS routing type is enabled on the router.
(Always IS-IS when the fields in this section are displayed.)
System Id: Identification value of the system.
0000.0C00.224D.00
IS-Type: level-1-2 Indicates what routing level (Level 1, Level 2 or both) is
enabled on the router.
Manual area address(es): Area addresses that have been configured.
39.0004.0030
Routing for area address(es): List of manually configured and learned area addresses.
39.0004.0030
Interfaces supported by IS-IS: List of interfaces on the router supporting IS-IS.
Next global update in 530 Next expected IS-IS update (in seconds).
seconds
Redistributing: Configuration of route redistribution.
Distance: Configured distance.

Cisco IOS ISO CLNS Command Reference

P5R-122
 Cisco IOS ISO CLNS Commands
show clns route

show clns route

To display one or all of the destinations to which this router knows how to route CLNS packets, use the
show clns route command in EXEC mode.

show clns route nsap

Syntax Description nsap CLNS network service access point (NSAP) address.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.
12.0(5)T Fields for displaying information about prefix routes were added or changed.

Usage Guidelines The show clns route command shows the Intermediate System-to-Intermediate System (IS-IS) Level 2
routing table and static and Intermediate System-to-Intermediate System Interior Gateway Routing
Protocol (ISO-IGRP) learned prefix routes. This table stores IS-IS area addresses and prefix routes.

Examples The following is sample output from the show clns route command when the nsap argument is not used:
Router# show clns route

ISO-IGRP Routing Table for Domain 49.0002, Area 0007

System Id Next-Hop SNPA Interface Metric State
milles milles *HDLC* Se1 8476 Up
0000.0000.0007 milles *HDLC* Se1 10476 Up
rips 0000.0000.0000 -- -- 0 Up

ISO-IGRP Routing Table for Domain 49.0002

Area Id Next-Hop SNPA Interface Metric State
0002 0000.0000.0000 -- -- 0 Up

Codes: C - connected, S - static, d - DecnetIV

I - ISO-IGRP, i - IS-IS, e - ES-IS

C 49.0002 [2/0], Local ISO-IGRP Domain

C 49.0001.0000.0000.0005.00 [1/0], Local IS-IS NET
C 49.0002.0007.0000.0000.0005.00 [1/0], Local ISO-IGRP NET
C 49.0001 [2/0], Local IS-IS Area

i 33.3333.3333 [110/10]
via bakel, Ethernet0
S 50.1234 [10/0], Discard Entry
I 55.5555.5555 [100/8476]
via milles, Serial1
S 77.7777.7777.7777 [10/0]

Cisco IOS ISO CLNS Command Reference

P5R-123
 Cisco IOS ISO CLNS Commands
show clns route

via Serial0
d 88.8888.8888.0007 [120/0], DecnetIV Entry
i 33.4567.8901 [110/10]
via bakel, Ethernet0

Table 13 describes the significant fields shown in the display.

Table 13 show clns route Field Descriptions

Field Description
Domain 49.0002 The ISO-IGRP routing domain for which we are displaying
the routes.
Area 0007 The ISO-IGRP area in which the displayed the Level 1 host
routes are.
System Id Identification value of the system listed in the Level 1
forwarding table.
Area Id The identification value of the area listed in the area
forwarding table.
Next-Hop System ID of the best cost next-hop to listed address.
SNPA MAC address of the next-hop system.
Interface Interface through which next-hop system is known.
Metric ISO-IGRP cost to reach the destination.
State Up (active) or Down (nonoperational).

Table 14 describes the codes as they appear in the previous display.

Table 14 prefix routes Field Descriptions

Field Description
C (connected) The domain, area, or NET was learned via local
configuration.
S (static) The destination was learned via a locally configured static
route.
d (DECnet IV) The destination is a converted DECnet phase IV area address.
I (ISO-IGRP) The destination is a prefix learned via Level 2 ISO-IGRP.
i (IS-IS) The destination is a prefix learned via Level 2 IS-IS.
e (ES-IS) The destination is learned via end system-intermediate
system (ES-IS) redirects.
33.3333.3333 Destination prefix.
[110/10] Administrative distance/metric.
via bakel Next-hop system via which this destination is reachable.
Shown as a 6-byte system ID, or as symbolic name (if
available).
Ethernet0 Outgoing interface via which this destination is reachable.
Local IS-IS NET Prefix is the full NET configured under an IS-IS process.

Cisco IOS ISO CLNS Command Reference

P5R-124
Cisco IOS ISO CLNS Commands
show clns route

Table 14 prefix routes Field Descriptions (continued)

Field Description
Local ISO-IGRP NET Prefix is the full NET configured under an ISO-IGRP
process.
Local ISO-IGRP Domain Prefix is the domain part of a locally configured ISO-IGRP
NET. This prefix is installed for redistribution purposes.
Local IS-IS Area Prefix is the area address of a locally configured IS-IS NET.
This prefix is installed for redistribution purposes.
Discard Entry Prefix is learned via a locally configured static discard entry.
DecnetIV Entry Prefix is a combination of the locally configured DECnet
conversion prefix and a dynamically learned DECnet IV
route. This prefix is installed for redistribution purposes.

The following is sample output showing a single CLNS route using the show clns route command with
the nsap argument:
Router# show clns route 33.3333.3333

Routing entry for 33.3333.3333

Known via "isis", distance 110, metric 10, Dynamic Entry
Routing Descriptor Blocks:
via bakel, Ethernet0
isis, route metric is 10, route version is 4

Table 15 describes the significant fields shown in the display.

Table 15 show clns route Field Descriptions

Field Description
Routing entry for 33.3333.3333 The prefix route being examined.
Known via "isis", distance 110, This route was learned from an IS-IS routing process. The
metric 10, Dynamic Entry administrative distance is 110. The cost to reach the
destination is 10.
Routing Descriptor Blocks Each destination in the CLNS routing table can be reached by
one or more paths. Each path is stored in a Routing
Descriptor Block. The maximum number of paths in CLNS is
6.
via bakel, Ethernet0 Next-hop is neighbor “bakel.” Outgoing interface is
Ethernet0.
Redistributing via Protocols other than originating protocol that advertise this
prefix.
isis, route metric is 10, route Originating protocol, cost for this path, route version in case
version is 4 this is an IS-IS route.

Cisco IOS ISO CLNS Command Reference

P5R-125
 Cisco IOS ISO CLNS Commands
show clns route

Related Commands Command Description

show clns es-neighbors Lists the ES neighbors that this router knows.
show clns is-neighbors Displays IS-IS related information for IS-IS router adjacencies.
show clns neighbor areas Displays information about IS-IS neighbors and the areas to which they
belong.
show clns neighbors Displays both ES and IS neighbors.
show isis topology Displays a list of all connected routers in all areas.

Cisco IOS ISO CLNS Command Reference

P5R-126
 Cisco IOS ISO CLNS Commands
show clns traffic

show clns traffic

To list the CLNS packets that this router has seen, use the show clns traffic command in EXEC mode.

show clns area-tag traffic

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among all
IP or CLNS router processes for a given router. If an area tag is not specified,
a null tag is assumed and the process is referenced with a null tag. If an area
tag is specified, output is limited to the specified area.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show clns traffic command:
Router# show clns traffic

CLNS & ESIS Output: 139885, Input: 90406

CLNS Local: 0, Forward: 0
CLNS Discards:
Hdr Syntax: 150, Checksum: 0, Lifetime: 0, Output cngstn: 0
No Route: 0, Dst Unreachable 0, Encaps. Failed: 0
NLP Unknown: 0, Not an IS: 0
CLNS Options: Packets 19, total 19, bad 0, GQOS 0, cngstn exprncd 0
CLNS Segments: Segmented: 0, Failed: 0
CLNS Broadcasts: sent: 0, rcvd: 0
Echos: Rcvd 0 requests, 69679 replies
Sent 69701 requests, 0 replies
ESIS(sent/rcvd): ESHs: 0/34, ISHs: 483/1839, RDs: 0/0, QCF: 0/0
ISO IGRP: Querys (sent/rcvd): 0/0 Updates (sent/rcvd): 1279/1402
ISO IGRP: Router Hellos: (sent/rcvd): 1673/1848
ISO IGRP Syntax Errors: 0
IS-IS: Level-1 Hellos (sent/rcvd): 0/0
IS-IS: Level-2 Hellos (sent/rcvd): 0/0
IS-IS: PTP Hellos (sent/rcvd): 0/0
IS-IS: Level-1 LSPs (sent/rcvd): 0/0
IS-IS: Level-2 LSPs (sent/rcvd): 0/0
IS-IS: Level-1 CSNPs (sent/rcvd): 0/0
IS-IS: Level-2 CSNPs (sent/rcvd): 0/0
IS-IS: Level-1 PSNPs (sent/rcvd): 0/0
IS-IS: Level-2 PSNPs (sent/rcvd): 0/0
IS-IS: Level-1 DR Elections: 0
IS-IS: Level-2 DR Elections: 0
IS-IS: Level-1 SPF Calculations: 0
IS-IS: Level-2 SPF Calculations: 0

Cisco IOS ISO CLNS Command Reference

P5R-127
 Cisco IOS ISO CLNS Commands
show clns traffic

Table 16 describes significant fields shown in the display.

Table 16 show clns traffic Field Descriptions

Field Description
CLNS & ESIS Output Total number of packets that this router has sent.
Input Total number of packets that this router has received.
CLNS Local Lists the number of packets that were generated by this
router.
Forward Lists the number of packets that this router has forwarded.
CLNS Discards Lists the packets that CLNS has discarded, along with the
reason for the discard.
CLNS Options Lists the options that have been seen in CLNS packets.
CLNS Segments Lists the number of packets that have been segmented and
the number of failures that occurred because a packet could
not be segmented.
CLNS Broadcasts Lists the number of CLNS broadcasts that have been sent
and received.
Echos Lists the number of echo request packets and echo reply
packets that have been received. The line following this
field lists the number of echo request packets and echo reply
packets that have been sent.
ESIS (sent/rcvd) Lists the number of ESH, ISH, and Redirects sent and
received.
ISO IGRP Lists the number of IGRP queries and updates sent and
received.
Router Hellos Lists the number of IGRP router hello packets that have
been sent and received.
IS-IS: Level-1 hellos (sent/rcvd) Lists the number of Level 1 IS-IS hello packets sent and
received.
IS-IS: Level-2 hellos (sent/rcvd) Lists the number of Level 2 IS-IS hello packets sent and
received.
IS-IS: PTP hellos (sent/rcvd) Lists the number of point-to-point IS-IS hello packets sent
and received over serial links.
IS-IS: Level-1 LSPs (sent/rcvd) Lists the number of Level 1 link-state PDUs sent and
received.
IS-IS: Level-2 LSPs (sent/rcvd) Lists the number of Level 2 link-state PDUs sent and
received.
IS-IS: Level-1 CSNPs Lists the number of Level 1 CSNPs sent and received.
(sent/rcvd)
IS-IS: Level-2 CSNPs Lists the number of Level 2 CSNPs sent and received.
(sent/rcvd)
IS-IS: Level-1 PSNPs Lists the number of Level 1 PSNPs sent and received.
(sent/rcvd)

Cisco IOS ISO CLNS Command Reference

P5R-128
Cisco IOS ISO CLNS Commands
show clns traffic

Table 16 show clns traffic Field Descriptions (continued)

Field Description
IS-IS: Level-2 PSNPs Lists the number of Level 2 PSNPs sent and received.
(sent/rcvd)
IS-IS: Level-1 DR Elections Lists the number of times Level 1 designated router election
occurred.
IS-IS: Level-2 DR Elections Lists the number of times Level 2 designated router election
occurred.
IS-IS: Level-1 SPF Calculations Lists the number of times Level 1 shortest-path-first (SPF)
tree was computed.
IS-IS: Level-2 SPF Calculations Lists the number of times Level 2 SPF tree was computed.

Cisco IOS ISO CLNS Command Reference

P5R-129
 Cisco IOS ISO CLNS Commands
show isis routes

show isis routes

To display the Intermediate System-to-Intermediate System (IS-IS) Level 1 forwarding table for IS-IS
learned routes, use the show isis routes command in EXEC mode.

show isis area-tag routes

Syntax Description area-tag Required for multiarea IS-IS configuration. Optional for conventional IS-IS
configuration.
Meaningful name for a routing process. This name must be unique among all
IP or Connectionless Network Service (CLNS) router processes for a given
router. If an area tag is not specified, a null tag is assumed and the process is
referenced with a null tag. If an area tag is specified, output is limited to the
specified area.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show isis routes command:
Router# show isis routes

IS-IS Level-1 Routing Table - Version 34

System Id Next-Hop SNPA Interface Metric State
0000.0C00.0C35 0000.0C00.0C35 0000.0c00.0c36 Ethernet1 20 Up
0800.2B16.24EA 0800.2B16.24EA aa00.0400.2d05 Ethernet0 10 Up
0800.2B14.060E 0800.2B14.060E aa00.0400.9205 Ethernet0 10 Up
0800.2B14.0528 0800.2B14.0528 aa00.0400.9105 Ethernet0 10 Up
0000.0C00.40AF 0000.0000.0000 -- -- 0 Up
0000.0C00.62E6 0000.0C00.62E6 0000.0c00.62e7 Ethernet1 10 Up
AA00.0400.2D05 0800.2B16.24EA aa00.0400.2d05 Ethernet0 10 Up

Table 17 describes significant fields shown in the display.

Table 17 show isis routes Field Descriptions

Field Description
Version 34 Indicates version number of the Level 1 routing table. All Level 1
routes with a version number that does not match this number are
flushed from the routing table. The router’s version number
increments when the configuration changes from Level 1 or Level 1-2
to Level 2 only.
System Id Identification value of the system listed in Level 1 forwarding table.
Next-Hop System ID of best-cost next-hop to listed address.

Cisco IOS ISO CLNS Command Reference

P5R-130
Cisco IOS ISO CLNS Commands
show isis routes

Table 17 show isis routes Field Descriptions (continued)

Field Description
SNPA SNPA of next-hop system.
Interface Interface through which next-hop system is known.
Metric IS-IS metric for the route.
State Up (active) or Down (nonoperational).

Cisco IOS ISO CLNS Command Reference

P5R-131
 Cisco IOS ISO CLNS Commands
show route-map

show route-map
To display all route maps configured or only the one specified, use the show route-map command in
EXEC mode.

show route-map [map-name]

Syntax Description map-name (Optional) Name of a specific route map.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Examples The following is sample output from the show route-map command:
Router# show route-map

route-map sid, permit, sequence 10

Match clauses:
tag 1 2
Set clauses:
metric 5
route-map sid, permit, sequence 20
Match clauses:
tag 3 4
Set clauses:
metric 6

Table 18 describes the fields shown in the display:

Table 18 show route-map Field Descriptions

Field Description
route-map Name of the route map.
permit Indicates that the route is redistributed as controlled by the set
actions.
sequence Number that indicates the position a new route map is to have in the
list of route maps already configured with the same name.
Match clauses: Match criteria—conditions under which redistribution is allowed
tag for the current route map.
Set clauses: Set actions—the particular redistribution actions to perform if the
metric criteria enforced by the match commands are met.

Cisco IOS ISO CLNS Command Reference

P5R-132
 Cisco IOS ISO CLNS Commands
show route-map

Related Commands Command Description

redistribute (ISO CLNS) Redistributes routing information from one domain into another routing
domain.
route-map (ISO CLNS) Defines the conditions for redistributing routes from one routing protocol
into another.

Cisco IOS ISO CLNS Command Reference

P5R-133
 Cisco IOS ISO CLNS Commands
show tarp

show tarp
To display all global TID Address Resolution Protocol (TARP) parameters, use the show tarp command
in EXEC mode.

show tarp

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp command:
Router# show tarp

Global TARP information:

TID of this station is "cerd"
Timer T1 (timer for response to TARP Type 1 PDU) is 15 seconds
Timer T2 (timer for response to TARP Type 2 PDU) is 25 seconds
Timer T3 (timer for response to ARP request) is 40 seconds
Timer T4 (timer that starts when T2 expires) is 15 seconds
Loop Detection Buffer entry timeout: 300 seconds
TID cache entry timeout: 300 seconds
This station will propagate TARP PDUs
This station will originate TARP PDUs
TID<->NET cache is enabled
Sequence number that next packet originated by this station will have: 9
Update remote cache (URC) bit is 0
Packet lifetime: 100 hops
Protocol type used in outgoing packets: "FE"
N-Selector used in TARP PDU's: "AF"

Table 19 describes the fields shown in the display.

Table 19 show tarp Field Descriptions

Field Description
TID Target identifier assigned to this router by the tarp tid
command.
Timer T1 Number of seconds that the router will wait to receive a
response from a Type 1 PDU. The T1 timer is set by the tarp
t1-response-timer command.
Timer T2 Number of seconds that the router will wait to receive a
response from a Type 2 PDU. The T2 timer is set by the tarp
t2-response-timer command.

Cisco IOS ISO CLNS Command Reference

P5R-134
Cisco IOS ISO CLNS Commands
show tarp

Table 19 show tarp Field Descriptions (continued)

Field Description
Timer T3 Number of seconds that the router will wait for a response
from a Type 5 PDU. The T3 timer is set by the tarp
arp-request-timer command.
Timer T4 Number of seconds that the router will wait for a response
from a Type 2 PDU after the T2 timer has expired. The T4
timer is set by the tarp post-t2-response-timer command.
Loop Detection Buffer entry Number of seconds that a System ID-to-sequence number
timeout mapping entry remains in the loop-detection buffer table. The
loop-detection buffer timeout is set by the tarp ldb-timer
command.
TID cache entry timeout Number of seconds that a dynamically created TARP entry
remains in the TID cache. The cache timeout is set by the tarp
cache-timer command.
Propagate TARP PDUs Indicates whether the router can propagate TARP PDUs to its
TARP neighbors. This field is set by the tarp
global-propagate command.
Originate TARP PDUs Indicates whether the router can originate TARP PDUs. This
field is set by the tarp originate command.
TID<->NET cache Indicates whether the router will store TID-to-network
(NSAP) address mapping in cache. This field is set by the
tarp allow-caching command.
Sequence number Number used by the next packet to indicate if the packet is
newer than the last information received. This number can be
changed by the tarp sequence-number command.
Update remote cache Indicates the setting of the URC bit in outgoing PDUs. When
the bit is zero, the receiver of the PDU will update its cache
entry. When the bit is one, the receiver of the PDU will not
update its cache entry. This URC bit is set by the tarp urc
command.
Packet lifetime Number of hosts that a PDU can traverse before the PDU is
discarded. The packet lifetime is set by the tarp lifetime
command.
Protocol type Hexadecimal representation of the protocol used in outgoing
PDUs. The protocol type is set by the tarp protocol-type
command. Only CLNP (indicated by FE) is supported.
N-selector Hexadecimal representation of the N-selector used to indicate
that the packet is a TARP PDU. The N-selector is set by the
tarp nselector-type command. The default is AF.

Cisco IOS ISO CLNS Command Reference

P5R-135
 Cisco IOS ISO CLNS Commands
show tarp blacklisted-adjacencies

show tarp blacklisted-adjacencies

To list all adjacencies that have been blacklisted (that is, adjacencies that this router will not propagate
TARP PDUs to) by the tarp blacklist-adjacency command, use the show tarp blacklisted-adjacencies
command in EXEC mode.

show tarp blacklisted-adjacencies

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp blacklisted-adjacencies command:
Router# show tarp blacklisted-adjacencies

Adjacencies that we won't propagate TARP PDU's to:

49.0001.5555.5555.5555.00

Table 20 describes the field shown in the display.

Table 20 show tarp blacklisted adjacencies Field Descriptions

Field Description
49.0001.5555.5555.5555.00 NSAP address of the blacklisted router.

Related Commands Command Description

tarp blacklist-adjacency Blacklists the specified router so that the router does not receive
TARP PDUs propagated by this router.

Cisco IOS ISO CLNS Command Reference

P5R-136
 Cisco IOS ISO CLNS Commands
show tarp host

show tarp host

To display information about a specific TID Address Resolution Protocol (TARP) router stored in the
local TID cache, use the show tarp host command in EXEC mode.

show tarp host tid

Syntax Description tid Target identifier of the router from which you want information.
Alphanumeric string up to 255 characters.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp host command:
router# show tarp host artemis

TID of entry: artemis

NET of entry: 49.0001.1111.1111.1111.00
Entry type: DYNAMIC
Expiration time: 280 seconds

Table 21 describes the fields shown in the display.

Table 21 show tarp host Field Descriptions

Field Description
TID Target identifier of the router.
NET NSAP address of the router.
Entry type Type of entry in the TID cache. Values are local, dynamic, or static. A static
entry is created with the tarp map command.
Expiration time Amount of time that a dynamically created entry will remain in the TID cache.
The cache timer is set by the tarp cache-timer command.

Related Commands Command Description

tarp tid Assigns a TID to the router.

Cisco IOS ISO CLNS Command Reference

P5R-137
 Cisco IOS ISO CLNS Commands
show tarp interface

show tarp interface

To list all interfaces that have TID Address Resolution Protocol (TARP) enabled, use the show tarp
interface command in EXEC mode.

show tarp interface [type number]

Syntax Description type (Optional) Interface type.

number (Optional) Interface number.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp interface command:
Router# show tarp interface

Ethernet0 is up, line protocol is up, encapsulation is ARPA

TARP propagation is enabled on this interface

Table 22 describes the fields shown in the display.

Table 22 show tarp interface Field Descriptions

Field Description
Ethernet...is {up | down} Indicates whether the interface hardware is currently active (whether
carrier detect is present) or if it has been taken down by an
...is administratively down
administrator.
line protocol is {up | down | Indicates whether the software processes that handle the line protocol
administratively down} think the line is usable (that is, whether keepalives are successful).
Encapsulation Indicates the encapsulation method assigned to the interface.
TARP propagation Indicates whether this interface can propagate TARP PDUs. The
propagation is set by the tarp propagate command.

Related Commands Command Description

tarp enable Enables the TARP on an interface.
tarp propagate Reenables propagation of TARP PDUs on an interface.

Cisco IOS ISO CLNS Command Reference

P5R-138
 Cisco IOS ISO CLNS Commands
show tarp ldb

show tarp ldb

To display the contents of the loop-detection buffer table, use the show tarp ldb command in EXEC
mode.

show tarp ldb

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp ldb command:
Router# show tarp ldb

System ID Sequence Number Expiration (sec)

1111.1111.1111 4 240

Table 23 describes the fields shown in the display.

Table 23 show tarp ldb Field Descriptions

Field Description
System ID System ID of the router.
Sequence Number Sequence number of the last packet originated by the router specified
by the system ID.
Expiration (sec) Time, in seconds, left before this entry in the loop-detection buffer
table is cleared. The time is set by the tarp ldb-timer command.

Related Commands Command Description

clear tarp ldb-table Clears the system ID-to-sequence number mapping entries stored in the
TARP loop-detection buffer table.
tarp sequence-number Specifies the sequence number to be used in the next outgoing TARP PDU.

Cisco IOS ISO CLNS Command Reference

P5R-139
 Cisco IOS ISO CLNS Commands
show tarp map

show tarp map

To list all static entries in the TID cache that were configured with the tarp map command, use the show
tarp map command in EXEC mode.

show tarp map

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp map command:
Router# show tarp map

Static MAP entries:

shashi 49.0001.6666.6666.6666.00
sonali 49.0001.7777.7777.7777.00

Table 24 describes the fields shown in the display.

Table 24 show tarp map Field Descriptions

Field Description
shashi TID of the static entry.
49.0001.6666.6666.6666.00 NSAP address of the static entry.

Related Commands Command Description

clear tarp tid-table Clears the dynamically created TARP TID-to-NSAP address mapping
entries stored in TID cache.
tarp map Enters a TID-to-NSAP static map entry in the TID cache.

Cisco IOS ISO CLNS Command Reference

P5R-140
 Cisco IOS ISO CLNS Commands
show tarp static-adjacencies

show tarp static-adjacencies

To list all static TID Address Resolution Protocol (TARP) adjacencies that are configured with the tarp
route-static command, use the show tarp static-adjacencies command in EXEC mode.

show tarp static-adjacencies

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp static-adjacencies command:
Router# show tarp static-adjacencies

Manual (static) TARP adjacencies:

55.0001.0001.1111.1111.1111.1111.1111.1111.1111.00

Table 25 describes the field shown in the display.

Table 25 show tarp static-adjacencies Field Descriptions

Field Description
55.0001.0001.1111.1111.1111.1111.1111.1111.1111.0 NSAP address of the TARP adjacency.

Related Commands Command Description

tarp route-static Configures a static TARP adjacency.

Cisco IOS ISO CLNS Command Reference

P5R-141
 Cisco IOS ISO CLNS Commands
show tarp tid-cache

show tarp tid-cache

To display information about the entries in the TID cache, use the show tarp tid-cache command in
EXEC mode. Entries are created dynamically, statically, or as a result of assigning a TID to the device
by using the tarp tid command.

show tarp tid-cache [detail]

Syntax Description detail (Optional) List additional information in the TID/NET cache (such as the
expiration time for dynamic entries).

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp tid-cache command:
Router# show tarp tid-cache

TID ('*' : static; & : local) NSAP

* shashi 49.0001.6666.6666.6666.00
& router 49.0001.3333.3333.3333.00
* sonali 49.0001.7777.7777.7777.00
artemis 49.0001.1111.1111.1111.00

The following is sample output from the show tarp tid-cache detail command:
Router# show tarp tid-cache detail

TID ('*': static; &: local) NSAP

& router 49.0001.3333.3333.3333.00
Expiration time: NONE

Table 26 describes the fields shown in the displays.

Table 26 show tarp tid-cache Field Descriptions

Field Description
TID Target identifier assigned to the TID cache entry. Static entries are flagged
with an asterisk (*). The local entry is flagged with an ampersand (&).
NSAP NSAP address of the TID cache entry.
* An asterisk (*) indicates that the entry in the TID cache is static (that is, you
have created an entry in the TID cache with the tarp map command.

Cisco IOS ISO CLNS Command Reference

P5R-142
 Cisco IOS ISO CLNS Commands
show tarp tid-cache

Table 26 show tarp tid-cache Field Descriptions (continued)

Field Description
& An ampersand (&) indicates that the entry in the TID cache is the local entry
(that is, the router to which you are connected).
Expiration time Amount of time the entry remains in the TID cache. When this time expires,
the entry is removed from the TID cache. Only dynamic entries have an
expiration time. The local entry indicated by an ampersand (&) and static
entries indicated by an asterisk (*) are not removed from the TID cache.

Related Commands Command Description

clear tarp tid-table Clears the dynamically created TARP TID-to-NSAP address mapping
entries stored in TID cache.
tarp cache-timer Specifies the length of time that a dynamically created TARP entry remains
in the TID cache.
tarp map Enters a TID-to-NSAP static map entry in the TID cache.
tarp tid Assigns a TID to the router.

Cisco IOS ISO CLNS Command Reference

P5R-143
 Cisco IOS ISO CLNS Commands
show tarp traffic

show tarp traffic

To display statistics about TID Address Resolution Protocol (TARP) PDUs since the last time the
counters were cleared, use the show tarp traffic command in EXEC mode.

show tarp traffic

Syntax Description This command has no arguments or keywords.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Examples The following is sample output from the show tarp traffic command:
Router# show tarp traffic

TARP counters:
Packets output: 11, Input: 5
Hdr syntax: 0
No memory: 0, Invalid packet: 0
Lifetime exceeded: 0

Table 27 describes the fields shown in the display.

Table 27 show tarp traffic Field Descriptions

Field Description
Packets output Indicates the number of PDUs that this router has originated.
Input Indicates the number of PDUs that this router has received.
Hdr syntax Number of PDUs with bad header information.
No memory Number of times a request for memory failed (because of insufficient
memory).
Invalid packets Number of received PDUs that contained invalid information.
Lifetime exceeded Number of received PDUs with zero lifetime.

Related Commands Command Description

clear tarp counters Clears all TARP counters that are displayed with the show tarp traffic
command.

Cisco IOS ISO CLNS Command Reference

P5R-144
 Cisco IOS ISO CLNS Commands
tarp allow-caching

tarp allow-caching
To reenable the storage of TID-to-NSAP address mapping in the TID cache, use the tarp allow-caching
command in global configuration mode. To disable this function and clear the TID cache, use the no form
of this command.

tarp allow-caching

no tarp allow-caching

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines By default, storing TID-to-network (NSAP) address mapping in the cache is enabled unless you
specifically disable the capability with the no tarp allow-caching command. If you disable this
capability, you must use the tarp allow-caching command to reenable storage of TID-to-network
address mapping in cache. After re-enabling this capability, any previously cleared local entry and all
static entries are restored.

Examples The following example disables storage of TID-to-NSAP address mapping in cache on the router:
no tarp allow-caching

Related Commands Command Description

clear tarp tid-table Clears the dynamically created TARP TID-to-NSAP address mapping
entries stored in TID cache.
show tarp map Lists all static entries in the TID cache that were configured with the tarp
map command.
show tarp tid-cache Displays information about the entries in the TID cache.
tarp cache-timer Specifies the length of time that a dynamically created TARP entry remains
in the TID cache.
tarp map Enters a TID-to-NSAP static map entry in the TID cache.

Cisco IOS ISO CLNS Command Reference

P5R-145
 Cisco IOS ISO CLNS Commands
tarp arp-request-timer

tarp arp-request-timer
To set the timeout for TID Address Resolution Protocol (TARP) Type 5 PDUs, use the tarp
arp-request-timer command in global configuration mode. To set the timeout to the default value, use
the no form of this command.

tarp arp-request-timer seconds

no tarp arp-request-timer

Syntax Description seconds Number of seconds for which the router will wait for a response from a
TARP Type 5 PDU. The range is from 0 to 3600 seconds.

Defaults 40 seconds

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines You may want to increase the time if your network has a slow link or there are long delay times on the
link.
TARP Type 5 PDUs are sent by the tarp query command to determine a TID that corresponds to a
particular NSAP.

Examples The following example sets the timeout for TARP Type 5 PDUs to 60 seconds (one minute):
tarp arp-request-timer 60

Related Commands Command Description

tarp lifetime Specifies the lifetime for locally generated TARP PDUs based on the number
of hops.
tarp query Determines a TID corresponding to a specific NSAP address.

Cisco IOS ISO CLNS Command Reference

P5R-146
 Cisco IOS ISO CLNS Commands
tarp blacklist-adjacency

tarp blacklist-adjacency
To blacklist the specified router so that the router does not receive TID Address Resolution Protocol
(TARP) PDUs propagated by this router, use the tarp blacklist-adjacency command in global
configuration mode. To remove the specified router from the blacklist so that the router can once again
receive propagated TARP PDUs, use the no form of this command.

tarp blacklist-adjacency nsap

no tarp blacklist-adjacency nsap

Syntax Description nsap NSAP address that cannot receive TARP PDUs. Use the full NSAP address.

Defaults All hosts receive propagated TARP PDUs.

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines A TARP router propagates PDUs to all its TARP adjacencies (both dynamic and static). Use the tarp
blacklist-adjacency command to bypass hosts that may not have TARP running or to bypass hosts to
which you do not want to propagate TARP PDUs.

Examples The following example specifies that the router 49.0001.0000.0c00.1111.1234.00 will not receive
propagated TARP PDUs:
tarp blacklist-adjacency 49.0001.0000.0c00.1111.1234.00

Related Commands Command Description

show tarp blacklisted-adjacencies Lists all blacklisted adjacencies (to which this router will not
propagate TARP PDUs) by the tarp blacklist-adjacency
command.

Cisco IOS ISO CLNS Command Reference

P5R-147
 Cisco IOS ISO CLNS Commands
tarp cache-timer

tarp cache-timer
To specify the length of time for which a dynamically created TID Address Resolution Protocol (TARP)
entry remains in the TID cache, use the tarp cache-timer command in global configuration mode. To
set the timer to the default value, use the no form of this command.

tarp cache-timer seconds

no tarp cache-timer

Syntax Description seconds Number of seconds for which an entry remains in the TID cache. The range
is 30 to 86,400 seconds.

Defaults 3,600 seconds (one hour)

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Static entries (those created with the tarp map command) remain in the TID cache unless cleared by the
no tarp map command.
If entries frequently change, you may want to use a shorter time period. If entries are stable, you may
want to use a longer time period.

Examples The following example limits the time for which an entry remains in the TID cache to 1,800 seconds
(30 minutes):
tarp cache-timer 1800

Related Commands Command Description

clear tarp tid-table Clears the dynamically created TARP TID-to-NSAP address mapping
entries stored in TID cache.
show tarp tid-cache Displays information about the entries in the TID cache.

Cisco IOS ISO CLNS Command Reference

P5R-148
 Cisco IOS ISO CLNS Commands
tarp enable

tarp enable
To enable TID Address Resolution Protocol (TARP) on an interface, use the tarp enable command in
interface configuration mode. To disable TARP on a particular interface, use the no form of this
command.

tarp enable

no tarp enable

Syntax Description This command has no arguments or keywords.

Defaults Disabled

Command Modes Interface configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Enabling TARP allows the interface to request and respond to TARP PDUs. TARP PDUs are identified
by a unique N-selector in the NSAP address. You must also have the TARP process running on the router
by using the tarp run command.

Examples The following example enables TARP on Ethernet interface 0:

interface ethernet 0
tarp enable

Related Commands Command Description

show tarp interface Lists all interfaces that have TARP enabled.
tarp nselector-type Specifies the N-selector to be used in CLNP PDUs to indicate that the packet
is a TARP PDU.
tarp propagate Reenables propagation of TARP PDUs on an interface.
tarp run Starts the TARP process on the router.

Cisco IOS ISO CLNS Command Reference

P5R-149
 Cisco IOS ISO CLNS Commands
tarp global-propagate

tarp global-propagate
To reenable the capability to propagate TID Address Resolution Protocol (TARP) PDUs globally, use
the tarp global-propagate command in global configuration mode. To disable global propagation of
TARP PDUs, use the no form of this command.

tarp global-propagate

no tarp global-propagate

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines TARP PDUs are globally propagated to all TARP neighbors by default unless you specifically disable
the capability with the no tarp global-propagate command. If you disable this capability, you must use
the tarp global-propagate command to reenable global purgation of TARP PDUs.
TARP PDUs are propagated on all interfaces by default unless you specifically disable the capability on
a specific interface with the no tarp propagate command.

Note The no tarp global-propagate command disables propagation of TARP PDUs on the router (and
thus on all interfaces).

Examples The following example disables global propagation of TARP PDUs on this router:
no tarp global-propagate

Related Commands Command Description

tarp propagate Reenables propagation of TARP PDUs on an interface.

Cisco IOS ISO CLNS Command Reference

P5R-150
 Cisco IOS ISO CLNS Commands
tarp ldb-timer

tarp ldb-timer
To specify the length of time for which a system ID-to-sequence number mapping entry remains in the
loop-detection buffer table, use the tarp ldb-timer command in global configuration mode. To set the
timer to the default value, use the no form of this command.

tarp ldb-timer seconds

no tarp ldb-timer

Syntax Description seconds Number of seconds for which a system ID-to-sequence number mapping
entry remains in the loop-detection buffer table. The range is 0 to 86,400
seconds. The default is 300 seconds.

Defaults 300 seconds

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines The loop-detection buffer table prevents TARP PDUs from looping.

Examples The following example limits the time for which an entry remains in the loop-detection buffer table to
600 seconds (10 minutes):
tarp ldb-timer 600

Related Commands Command Description

clear tarp ldb-table Clears the system ID-to-sequence number mapping entries stored in the
TARP loop-detection buffer table.
show tarp ldb Displays the contents of the loop-detection buffer table.
tarp lifetime Specifies the lifetime for locally generated TARP PDUs based on the number
of hops.

Cisco IOS ISO CLNS Command Reference

P5R-151
 Cisco IOS ISO CLNS Commands
tarp lifetime

tarp lifetime
To specify the lifetime for locally generated TID Address Resolution Protocol (TARP) PDUs based on
the number of hops, use the tarp lifetime command in global configuration mode. To set the PDU
lifetime to the default value, use the no form of this command.

tarp lifetime hops

no tarp lifetime

Syntax Description hops Number of hosts that a PDU can traverse before it is discarded. Each router
represents one hop. The range is 0 to 65,535 hops. The default is 100 hops.

Defaults 100 hops

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines The number of hops specified is decremented after every hop. A PDU with a lifetime of zero is discarded.

Examples The following example specifies that the TARP PDU can traverse 150 hosts before it is discarded:
tarp lifetime 150

Related Commands Command Description

tarp arp-request-timer Sets the timeout for waiting for a response to a TARP Type 5 PDU.
tarp ldb-timer Specifies the length of time that a system ID-to-sequence number mapping
entry remains in the loop-detection buffer table.

Cisco IOS ISO CLNS Command Reference

P5R-152
 Cisco IOS ISO CLNS Commands
tarp map

tarp map
To enter a TID-to-NSAP static map entry in the TID cache, use the tarp map command in global
configuration mode. To remove a static map entry from the TID cache, use the no form of this command.

tarp map tid nsap

no tarp map tid nsap

Syntax Description tid Target identifier to be mapped to the specified NSAP. Alphanumeric string
up to 255 characters.
nsap NSAP address to map to the specified TID. Use the full NSAP address.

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Use the tarp map command to map multiple NSAP addresses on a router. For example, using the tarp
resolve to get the NSAP for a known TID will always return the first NSAP address. If the router has
multiple NSAP addresses, you can use the tarp map command to map the TID to multiple NSAP
addresses. If a router has NSAP addresses 1, 2, 3, the tarp resolve command will always return NSAP
address 1. Use the tarp map command to map the router to NSAP addresses 2 and 3 so the tarp query
command will return the TID corresponding to the other NSAP addresses.

Examples The following example maps the NSAP address 49.0001.000.1111.1111.1234.00 to TID SJ1:
tarp map sj1 49.0001.0000.1111.1111.1234.00

Related Commands Command Description

clear tarp tid-table Clears the dynamically created TARP TID-to-NSAP address mapping
entries stored in TID cache.
show tarp map Lists all static entries in the TID cache that were configured with the tarp
map command.
tarp query Determines a TID corresponding to a specific NSAP address.
tarp resolve Determines an NSAP address corresponding to a specified TID.

Cisco IOS ISO CLNS Command Reference

P5R-153
 Cisco IOS ISO CLNS Commands
tarp nselector-type

tarp nselector-type
To specify the N-selector to be used in Connectionless Network Protocol (CLNP) PDUs to indicate that
the packet is a TID Address Resolution Protocol (TARP) PDU, use the tarp nselector-type command
in global configuration mode. To set the N-selector to the default value, use the no form of this
command.

tarp nselector-type hex-digit

no tarp nselector-type

Syntax Description hex-digit Two digits in hexadecimal format to be used to identify TARP PDUs.

Defaults AF

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines This feature provides flexibility in using the N-selector field to indicate TARP PDUs. The N-selector
must be the same on all hosts running the TARP process.

Examples The following example changes the N-selector used in CLNP PDUs to BC:
tarp nselector-type BC

Related Commands Command Description

show tarp Displays all global TARP parameters.

Cisco IOS ISO CLNS Command Reference

P5R-154
 Cisco IOS ISO CLNS Commands
tarp originate

tarp originate
To reenable the router to originate TID Address Resolution Protocol (TARP) PDUs, use the tarp
originate command in global configuration mode. To disable the capability to originate TARP PDUs,
use the no form of this command.

tarp originate

no tarp originate

Syntax Description This command has no arguments or keywords.

Defaults Enabled

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Origination of TARP PDUs is enabled by default unless you specifically disable the capability with the
no tarp originate command. If you disable this capability, you must use the tarp originate command
to reenable origination of TARP PDUs.

Examples The following example disables the origination of TARP PDUs on this router:
no tarp originate

Related Commands Command Description

show tarp Displays all global TARP parameters.

Cisco IOS ISO CLNS Command Reference

P5R-155
 Cisco IOS ISO CLNS Commands
tarp post-t2-response-timer

tarp post-t2-response-timer
To specify the length of time for which a router waits for a response to a Type 2 PDU after the default
timer expires, use the tarp post-t2-response-timer command in global configuration mode. To set the
timer to the default value, use the no form of this command.

tarp post-t2-response-timer seconds

no tarp post-t2-response-timer

Syntax Description seconds Number of seconds for which the router will wait for a response for a Type
2 PDU after the default timer has expired. The range is 0 to 3600 seconds.

Defaults 15 seconds

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines A Type 1 PDU is sent to all Level 1 (IS-IS and ES-IS) neighbors when a router has a TID for which it
has no matching NSAP information. If no response is received within the specified timeout period, a
Type 2 PDU is sent to all Level 1 and Level 2 neighbors. If no response is received within the specified
timeout period, additional time is allocated based on the number specified in the tarp
post-t2-response-timer command.

Examples The following example sets the additional time to wait for a response from a Type 2 PDU to 60 seconds:
tarp post-t2-response-timer 60

Related Commands Command Description

tarp t2-response-timer Specifies the length of time for which the router will wait for a response
from a Type 2 PDU.

Cisco IOS ISO CLNS Command Reference

P5R-156
 Cisco IOS ISO CLNS Commands
tarp propagate

tarp propagate
To reenable propagation of TID Address Resolution Protocol (TARP) PDUs on an interface, use the tarp
propagate command in interface configuration mode. To disable propagation of TARP PDUs on one or
more interfaces, use the no form of this command.

tarp propagate [all | message-type type-number [type-number] [type-number]]

no tarp propagate [all | message-type type-number [type-number] [type-number]]

Syntax Description all (Optional) Specifies all TARP PDUs.

message-type (Optional) Specifies only type-number broadcast PDUs. Valid values are
type-number 1, 2, and 4. You may enter more than one value for the type-number
argument.

Defaults Enabled

Command Modes Interface configuration

Command History Release Modification

11.1 This command was introduced.
12.0(5)T The following keywords and arguments were added:
• all
• message-type type-number

Usage Guidelines Pressing Return or Enter after tarp propagate is the same as typing the keyword all.
TARP PDUs are propagated on all interfaces by default unless you specifically disable the capability on
a specific interface with the no tarp propagate command. If you disable this capability, you must use
the tarp propagate command to reenable propagation of TARP PDUs. Enabling propagation of TARP
PDUs allows the interface to propagate PDUs to all neighbors on this interface. TARP PDUs are
identified by a unique N-selector in the NSAP.

Note The no tarp global-propagate command disables propagation of TARP PDUs on the router (and,
thus, on all interfaces).

Examples The following example starts the TARP process on the router and enables TARP propagation on Ethernet
interface 0:
interface ethernet 0
tarp propagate

Cisco IOS ISO CLNS Command Reference

P5R-157
 Cisco IOS ISO CLNS Commands
tarp propagate

Related Commands Command Description

show tarp interface Lists all interfaces that have TARP enabled.
tarp enable Enables the TARP on an interface.
tarp global-propagate Reenables the capability to propagate TARP PDUs globally.
tarp nselector-type Specifies the N-selector to be used in CLNP PDUs to indicate that the packet
is a TARP PDU.
tarp run Starts the TARP process on the router.

Cisco IOS ISO CLNS Command Reference

P5R-158
 Cisco IOS ISO CLNS Commands
tarp protocol-type

tarp protocol-type
To specify the network protocol type to be used in outgoing TID Address Resolution Protocol (TARP)
PDUs, use the tarp protocol-type command in global configuration mode. To set the protocol type to
the default value, use the no form of this command.

tarp protocol-type hex-digit

no tarp protocol-type

Syntax Description hex-digit Two digits in hexadecimal format to be used to identify the protocol used in
outgoing TARP PDUs. The default is FE (for CLNP).

Defaults FE

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines Only FE is supported.

Examples The following example shows the TARP network protocol type changed from the default of FE to AO:
tarp protocol-type ao

Related Commands Command Description

show tarp Displays all global TARP parameters.

Cisco IOS ISO CLNS Command Reference

P5R-159
 Cisco IOS ISO CLNS Commands
tarp query

tarp query
To determine a corresponding TID entry for a specific NSAP address, use the tarp query command in
EXEC mode.

tarp query nsap

Syntax Description nsap NSAP address that you want the TID for. Use the full NSAP address.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines If there is a TID entry in the local TID cache, the requested information is displayed.
If there is no TID entry in the local TID cache, a TARP Type 5 PDU is sent to the specified NSAP
address. Because the NSAP address is specified, the PDU is unicast to the particular NSAP address. If
a response is received (in the form of a Type 3 PDU), the local TID cache is updated and the requested
information is displayed.
The length of time that the router will wait for a response to a Type 5 PDU is controlled by the tarp
arp-request-timer command.

Examples The following is sample output from the tarp query command:
Router# tarp query 49.0001.3333.3333.3333.00

Type escape sequence to abort.

Sending TARP type 5 PDU, timeout 40 seconds...

TID corresponding to NET 49.0001.3333.3333.3333.00 is cerd

Table 28 describes the fields shown in the display.

Table 28 tarp query Field Descriptions

Field Description
Sending TARP type 5 PDU PDU requesting the TID of the specified NSAP.
Timeout... Number of seconds the router will wait for a response from
the Type 5 PDU. The timeout is set by the tarp
arp-request-timer command.
TID corresponding to... is... Indicates the TID for the specified NSAP address.

Cisco IOS ISO CLNS Command Reference

P5R-160
 Cisco IOS ISO CLNS Commands
tarp query

Related Commands Command Description

show tarp Displays all global TARP parameters.
tarp arp-request-timer Sets the timeout for TARP Type 5 PDUs.

Cisco IOS ISO CLNS Command Reference

P5R-161
 Cisco IOS ISO CLNS Commands
tarp resolve

tarp resolve
To determine an NSAP address corresponding to a specified TID, use the tarp resolve command in
EXEC mode.

tarp resolve tid [1 | 2]

Syntax Description tid Target identifier to be mapped to the specified NSAP. Alphanumeric string
up to 255 characters.
1 (Optional) Send a Type 1 PDU. The default is a Type 1 PDU. If a response
is not received before the timeout period, a Type 2 PDU is sent.
2 (Optional) Send only Type 2 PDU.

Command Modes EXEC

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines If there is an NSAP entry in the local TID cache, the requested information is displayed.
If there is no NSAP entry in the local TID cache, a TARP Type 1 or Type 2 PDU is sent out. By default
a Type 1 PDU is sent. A Type 1 PDU is sent to all Level 1 (IS-IS and ES-IS) neighbors. If a response is
received (in the form of a Type 3 PDU), the local TID cache is updated and the requested information is
displayed.
If a response from the Type 1 PDU is not received within the timeout period, a Type 2 PDU is sent to all
Level 1 and Level 2 neighbors. If a response is received (in the form of a Type 3 PDU), the local TID
cache is updated and the requested information is displayed.
The length of time that the router will wait for a response to a Type 1 PDU is controlled by the tarp
t1-response-timer command. The length of time that the router waits for a response to a Type 2 PDU is
controlled by the tarp t2-response-timer command and the tarp-post-t2-response-timer command.

Examples The following is sample output from the tarp resolve command:
Router# tarp resolve artemis

Type escape sequence to abort.

Sending TARP type 1 PDU, timeout 15 seconds...

NET corresponding to TID artemis is 49.0001.1111.1111.1111.00

Table 29 describes the fields shown in the display.

Cisco IOS ISO CLNS Command Reference

P5R-162
 Cisco IOS ISO CLNS Commands
tarp resolve

Table 29 tarp resolve Field Descriptions

Field Description
Sending TARP type 1 PDU PDU requesting the NSAP of the specified TID.
timeout... Number of seconds the router will wait for a response from
the Type 1 PDU. The timeout is set by the tarp
t1-response-timer command.
NET corresponding to... is... Indicates the NSAP address (in this case,
49.0001.1111.1111.1111.00) for the specified TID.

Related Commands Command Description

tarp map Enters a TID-to-NSAP static map entry in the TID cache.
tarp post-t2-response-timer Specifies the length of time that a router waits for a response to a
Type 2 PDU after the default timer expires.
tarp t1-response-timer Specifies the length of time for which the router will wait for a
response from a Type 1 PDU.
tarp t2-response-timer Specifies the length of time for which the router will wait for a
response from a Type 2 PDU.

Cisco IOS ISO CLNS Command Reference

P5R-163
 Cisco IOS ISO CLNS Commands
tarp route-static

tarp route-static
To configure a static TID Address Resolution Protocol (TARP) adjacency, use the tarp route-static
command in global configuration mode. To remove a static TARP adjacency from the TARP queue, use
the no form of this command.

tarp route-static nsap [all | message-type type-number [type-number] [type-number]]

no tarp route-static nsap [all | message-type type-number [type-number] [type-number]]

Syntax Description nsap NSAP address to create a static TARP adjacency. Use the full NSAP address.
all (Optional) Specifies all TARP PDUs.
message-type (Optional) Specifies only type-number broadcast PDUs.Valid values are
type-number 1, 2, and 4. You may enter more than one value for the type-number
argument.

Defaults No default behavior or values

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.
12.0 The following keywords and arguments were added:
• all
• message-type type-number

Usage Guidelines Pressing Return or Enter after tarp route-static is the same as typing the keyword all.
A TARP router propagates PDUs to all its adjacencies and static TARP adjacencies.
If a router is not running TARP, the router discards TARP PDUs rather than propagating the PDUs to all
its adjacencies. To allow propagation of the PDU to hosts that are “beyond” a non-TARP router, you must
use the tarp route-static command to ensure that the hosts receive PDUs. The tarp route-static
command allows TARP PDUs to “tunnel” through hosts that are not running TARP.
The specified router, as identified by the NSAP address, is stored in a TARP static adjacencies queue.
Use the tarp blacklist-adjacency command to prevent sending TARP PDUs directly to hosts that are
not running TARP.

Examples The following example adds 49.0001.0000.0c00.1111.1234.00 as a static TARP adjacency to the TARP
queue:
tarp route-static 49.0001.0000.0c00.1111.1234.00

Cisco IOS ISO CLNS Command Reference

P5R-164
 Cisco IOS ISO CLNS Commands
tarp route-static

Related Commands Command Description

show tarp static-adjacencies Lists all static TARP adjacencies that are configured with the tarp
route-static command.
tarp blacklist-adjacency Blacklists the specified router so that the router does not receive
TARP PDUs propagated by this router.

Cisco IOS ISO CLNS Command Reference

P5R-165
 Cisco IOS ISO CLNS Commands
tarp run

tarp run
To start the TID Address Resolution Protocol (TARP) process on the router, use the tarp run command
in global configuration mode. To stop the TARP process, use the no form of this command.

tarp run

no tarp run

Syntax Description This command has no arguments or keywords.

Defaults No TARP process (unless configured to start in NVRAM).

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines You must also enable TARP on the individual interfaces by using the tarp enable command.

Examples The following example starts the TARP process on the router:
tarp run

Related Commands Command Description

tarp enable Enables the TARP on an interface.
tarp propagate Reenables propagation of TARP PDUs on an interface.

Cisco IOS ISO CLNS Command Reference

P5R-166
 Cisco IOS ISO CLNS Commands
tarp sequence-number

tarp sequence-number
To specify the sequence number to be used in the next originated TID Address Resolution Protocol
(TARP) PDU, use the tarp sequence-number command in global configuration mode. To return to the
default value, use the no form of this command.

tarp sequence-number number

no tarp sequence-number number

Syntax Description number Number from 0 to 65,535 that will be used as the sequence number in the
next originated PDU.

Defaults Zero

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines The sequence number lets the router determine if information received in the PDU is newer than the last
information received. You may want to increase the sequence number to ensure that other hosts update
their entries in TID cache.

Examples The following example causes a sequence number of 10 to be assigned to the next TARP PDU:
tarp sequence-number 10

Related Commands Command Description

show tarp Displays all global TARP parameters.
show tarp ldb Displays the contents of the loop-detection buffer table.

Cisco IOS ISO CLNS Command Reference

P5R-167
 Cisco IOS ISO CLNS Commands
tarp t1-response-timer

tarp t1-response-timer
To specify the length of time for which the router will wait for a response from a Type 1 PDU, use the
tarp t1-response-timer command in global configuration mode. To set the timer to the default value,
use the no form of this command.

tarp t1-response-timer seconds

no tarp t1-response-timer

Syntax Description seconds Number of seconds for which the router will wait to receive a response from
a Type 1 PDU. The range is 0 to 3600 seconds.

Defaults 15 seconds

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines A Type 1 PDU is sent to all Level 1 (IS-IS and ES-IS) neighbors when a router has a TID for which it
has no matching NSAP information. If no response is received within the timeout period (specified by
the tarp t1-response-timer command), a Type 2 PDU is sent to all Level 2 neighbors.

Examples The following example sets the timeout period for a Type 1 PDU to 60 seconds:
tarp t1-response-timer 60

Related Commands Command Description

tarp t2-response-timer Specifies the length of time for which the router will wait for a response
from a Type 2 PDU.

Cisco IOS ISO CLNS Command Reference

P5R-168
 Cisco IOS ISO CLNS Commands
tarp t2-response-timer

tarp t2-response-timer
To specify the length of time for which the router will wait for a response from a Type 2 PDU, use the
tarp t2-response-timer command in global configuration mode. To set the timer to the default value,
use the no form of this command.

tarp t2-response-timer seconds

no tarp t2-response-timer

Syntax Description seconds Number of seconds for which the router will wait to receive a response
from a Type 2 PDU. The range is 0 to 3600 seconds.

Defaults 25 seconds

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines A Type 1 PDU is sent to all Level 1 (IS-IS and ES-IS) neighbors when a router has a TID for which it
has no matching NSAP information. If no response is received within the timeout period (specified by
the tarp t1-response-timer command), a Type 2 PDU is sent to all Level 2 neighbors. If no response is
received within the timeout period (specified by the tarp t2-response-timer command), additional time
can be allocated by using the tarp post-t2-response-timer command.

Examples The following example sets the timeout period for a Type 2 PDU to 60 seconds:
tarp t2-response-timer 60

Related Commands Command Description

tarp post-t2-response-timer Specifies the length of time for which a router waits for a response to
a Type 2 PDU after the default timer expires.
tarp t1-response-timer Specifies the length of time for which the router will wait for a
response from a Type 1 PDU.

Cisco IOS ISO CLNS Command Reference

P5R-169
 Cisco IOS ISO CLNS Commands
tarp tid

tarp tid
To assign a TID to the router, use the tarp tid command in global configuration mode. To remove the
TID from the router, use the no form of this command.

tarp tid tid

no tarp tid tid

Syntax Description tid Target identifier to be used by this router. Alphanumeric string up to 255
characters.

Defaults No default behavior or values

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines All hosts using TID Address Resolution Protocol (TARP) must have a unique TID assigned.

Examples The following example assigns the TID SJ3 to the router:
tarp tid sj3

Related Commands Command Description

show tarp Displays all global TARP parameters.
show tarp host Displays information about a specific TARP router stored in the local TID
cache.
show tarp tid-cache Displays information about the entries in the TID cache.

Cisco IOS ISO CLNS Command Reference

P5R-170
 Cisco IOS ISO CLNS Commands
tarp urc

tarp urc
To set the update remote cache bit in all subsequent outgoing PDUs, use the tarp urc command in global
configuration mode. To set the update remote cache bit to the default value, use the no form of this
command.

tarp urc {0 | 1}

no tarp urc

Syntax Description 0 Sets the update remote cache bit to 0, which is the default value. When the
bit is zero, the receiver’s PDU will update its TID cache entry.
1 Sets the update remote cache bit to 1. When the bit is 1, the receiver’s TID
cache is not updated.

Defaults The default value is 0.

Command Modes Global configuration

Command History Release Modification

11.1 This command was introduced.

Usage Guidelines If you do not specify either 0 or 1, the default value 0 is used.

Examples The following example sets the update remote cache bit in the outgoing PDU to 1, so the cache at the
receiver’s end is not updated:
tarp urc 1

Related Commands Command Description

show tarp Displays all global TARP parameters.

Cisco IOS ISO CLNS Command Reference

P5R-171
 Cisco IOS ISO CLNS Commands
timers basic (ISO CLNS)

timers basic (ISO CLNS)

To configure ISO IGRP timers, use the timers basic command in router configuration mode. To restore
the default values, use the no form of this command.

timers basic update-interval holddown-interval invalid-interval

no timers basic update-interval holddown-interval invalid-interval

Syntax Description update-interval Time, in seconds, between the sending of routing updates.
holddown-interval Time, in seconds, a system or area router is kept in holddown state, during
which routing information regarding better paths is suppressed. (A router
enters into a holddown state when an update packet is received that indicates
the route is unreachable. The route is marked inaccessible and advertised as
unreachable. However, the route is still used for forwarding packets.) When
the holddown interval expires, routes advertised by other sources are
accepted and the route is no longer inaccessible.
invalid-interval Time, in seconds, that a route remains in the routing table after it has been
determined that it is not reachable. After that length of time, the route is
removed from the routing table.

Defaults update-interval: 90 seconds

holddown-interval: 145 seconds
invalid-interval: 135 seconds

Command Modes Router configuration

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Because the ISO IGRP routing protocol executes a distributed, asynchronous routing algorithm, it is
important that these timers be the same for all routers in the network.

Examples In the following example, updates are broadcast every 60 seconds. When an update packet is received
that indicates the router is unreachable, the router will be in holddown state for 100 seconds before once
more becoming accessible. If a router is not heard from in 130 seconds, the route is removed from the
routing table.
router iso-igrp
timers basic 60 100 130

Cisco IOS ISO CLNS Command Reference

P5R-172
 Cisco IOS ISO CLNS Commands
which-route

which-route
To determine which next-hop router will be used or to troubleshoot your configuration if you have
multiple processes running, use the which-route command in EXEC mode. This command displays the
routing table in which the specified CLNS destination is found.

which-route {nsap-address | clns-name}

Syntax Description nsap-address CLNS destination network address.

clns-name Destination host name.

Command Modes EXEC

Command History Release Modification

10.0 This command was introduced.

Usage Guidelines Route information can reside in the following tables:

• IS-IS Level 1 routing table
• ISO IGRP system-id or area routing table
• Prefix routing table (IS-IS Level 2 routes, ISO IGRP domain routes, and static routes)
• Adjacency database

Examples The following example shows that destination information for router gray is found in the IS-IS Level 1
routing table. The destination is on the local system.
Router# which-route gray

Route look-up for destination 39.0001.0000.0c00.bda8.00, GRAY

Found route in IS-IS level-1 routing table - destination is local

The following example shows that destination information for NSAP address
49.0001.0000.0c00.bda8.00 is found in the ISO IGRP Level 1 routing table. The destination is on the
local system.
Router# which-route 49.0001.0000.0c00.bda8.00

Route look-up for destination 49.0001.0000.0c00.bda8.00

Found route in ISO IGRP routing table - destination is local

The following example shows that destination information for router green is found in the IS-IS
Level 1 routing table. The destination is not on the local system.
Router# which-route green

Route look-up for destination 39.0001.0000.0c00.7f06.00, GREEN

Found route in IS-IS level-1 routing table

Cisco IOS ISO CLNS Command Reference

P5R-173
 Cisco IOS ISO CLNS Commands
which-route

Adjacency entry used:

System Id SNPA Interface State Holdtime Type Protocol
GREEN 0000.0c00.2d55 Ethernet0 Up 91 L1L2 IS-IS
Area Address(es): 39.0001

Table 30 describes the display fields in the adjacency entry used to reach system green.

Table 30 which-route Field Descriptions

Field Description
System ID Six-byte value that identifies a system in an area. A name is displayed
in this field if one has been assigned with the clns host global
configuration command.
SNPA SNPA data link address.
Interface Interface from which system information was learned.
State State of the ES or IS. Possible values are as follows:
Init—The system is an IS and is waiting for an IS-IS hello message.
The neighbor to the IS-IS is not adjacent.
Up—The ES or IS is reachable.
Holdtime Number of seconds for which the information is valid.
Type Adjacency type. Possible values are as follows:
ES—An end-system adjacency that is either discovered by the ES-IS
protocol or statically configured.
IS—A router adjacency that is either discovered by the ES-IS protocol
or is statically configured.
L1—A router adjacency for Level 1 routing only.
L1L2—A router adjacency for Level 1 and Level 2 routing.
L2—A router adjacency for Level 2 only.
Protocol Protocol through which the adjacency was learned. Valid protocol
sources are ES-IS, IS-IS, ISO IGRP, and Static.

The following example shows that destination information for NSAP address
49.0001.1111.1111.1111.00 is found in the ISO IGRP routing table. Table 30 describes the display fields
in the adjacency entry used to reach NSAP address 49.0001.1111.1111.1111.00.
Router# which-route 49.0001.1111.1111.1111.00

Route look-up for destination 49.0001.1111.1111.1111.00

Found route in ISO IGRP routing table

Adjacency entry used:

System Id SNPA Interface State Holdtime Type Protocol
1111.1111.1111 0000.0c01.151d Ethernet1 Up 38 L1L2 ISO IGRP
Area Address(es): 49.0001

The following example indicates that the specified address is not found in a routing table:
Router# which-route 47.0003.0000.0000.0000.00

Route look-up for destination 47.0003.0000.0000.0000.00

Route not found

Cisco IOS ISO CLNS Command Reference

P5R-174
 Cisco IOS ISO CLNS Commands
which-route

The following example indicates that the specified NSAP address was found in the CLNS prefix routing
table. This information is followed by the route entry used to reach NSAP address
49.0003.0000.0000.0000.00.
Router# which-route 49.0003.0000.0000.0000.00

Route look-up for destination 49.0003.0000.0000.0000.00

Found route in CLNS prefix routing table

Route entry used:

49 [10/0]
via 1111.1111.1111, Ethernet1, Static

Related Commands Command Description

clns host Defines a name-to-NSAP mapping that can then be used with commands
requiring NSAPs.

Cisco IOS ISO CLNS Command Reference

P5R-175