Scribd
Upload
551 views

Transistor Testing

There are several ways to test transistors, including using a transistor tester, ohmmeter, or while still in a circuit. An ohmmeter can be used to perform two basic transistor tests: gain and junction resistance. For a gain test, the transistor is connected in a simple circuit with resistors and a switch. With the switch open, the ohmmeter reads high resistance, and with it closed the reading is lower, indicating current flow and normal gain. Junction resistance tests with an ohmmeter can reveal leaks, shorts, or opens between the base-emitter, base-collector, and collector-emitter by measuring the forward and reverse resistances.

Uploaded by

Jerry B Cruz
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
551 views

Transistor Testing

There are several ways to test transistors, including using a transistor tester, ohmmeter, or while still in a circuit. An ohmmeter can be used to perform two basic transistor tests: gain and junction resistance. For a gain test, the transistor is connected in a simple circuit with resistors and a switch. With the switch open, the ohmmeter reads high resistance, and with it closed the reading is lower, indicating current flow and normal gain. Junction resistance tests with an ohmmeter can reveal leaks, shorts, or opens between the base-emitter, base-collector, and collector-emitter by measuring the forward and reverse resistances.

Uploaded by

Jerry B Cruz
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

TRANSISTOR TESTING

There are several different ways of testing transistors. They can be tested while in the circuit
with a transistor tester or ohmmeter.

Transistor testers are nothing more than the solid-state equivalent of electron-tube testers
(although they do not operate on the same principle). With most transistor testers, it is possible to test
the transistor in or out of the circuit.

There are four basic tests required for transistors in practical troubleshooting: gain, leakage,
breakdown, and switching time. For maintenance and repair, however, a check of two or three
parameters is usually sufficient to determine whether a transistor needs to be replaced.

Since it is impractical to cover all the different types of transistor testers and since each tester
comes with its own operator's manual, we will move on to something you will use more frequently for
testing transistors-the ohmmeter.

Testing Transistors with an Ohmmeter

Two tests that can be done with an ohmmeter are gain, and junction resistance. Tests of a
transistor's junction resistance will reveal leakage, shorts, and opens.

TRANSISTOR GAIN TEST.—A basic transistor gain test can be made using an ohmmeter and a
simple test circuit. The test circuit can be made with just a couple of resistors and a switch, as shown in
figure 2-18. The principle behind the test lies in the fact that little or no current will flow in a transistor
between emitter and collector until the emitter-base junction is forward biased. The only precaution
you should observe is with the ohmmeter. Any internal battery may be used in the meter provided that
it does not exceed the maximum collector-emitter breakdown voltage.

Figure 2-18.—Testing a transistor's gain with an ohmmeter.


With the switch in figure 2-18 in the open position as shown, no voltage is applied to the PNP
transistor's base, and the emitter-base junction is not forward biased. Therefore, the ohmmeter should
read a high resistance, as indicated on the meter. When the switch is closed, the emitter-base circuit is
forward biased by the voltage across R1 and R2. Current now flows in the emitter-collector circuit, which
causes a lower resistance reading on the ohmmeter. A 10-to-1 resistance ratio in this test between
meter readings indicates a normal gain for an audio-frequency transistor.

To test an NPN transistor using this circuit, simply reverse the ohmmeter leads and carry out the
procedure described earlier.

TRANSISTOR JUNCTION RESISTANCE TEST.—An ohmmeter can be used to test a transistor for
leakage (an undesirable flow of current) by measuring the base-emitter, base-collector, and collector-
emitter forward and reverse resistances.

For simplicity, consider the transistor under test in each view of figure 2-19 (view A, view B and
view C) as two diodes connected back to back. Therefore, each diode will have a low forward resistance
and a high reverse resistance. By measuring these resistances with an ohmmeter as shown in the figure,
you can determine if the transistor is leaking current through its junctions. When making these
measurements, avoid using the R1 scale on the meter or a meter with a high internal battery voltage.
Either of these conditions can damage a low-power transistor.

Figure 2-19A.—Testing a transistor's leakage with an ohmmeter. COLLECTOR-TO-EMITTER TEST


Figure 2-19B.—Testing a transistor's leakage with an ohmmeter. BASE-TO-COLLECTOR TEST

Figure 2-19C.—Testing a transistor's leakage with an ohmmeter. BASE-TO-EMITTER TEST

Now consider the possible transistor problems that could exist if the indicated readings in figure
2-19are not obtained. A list of these problems is provided in table 2-2.

Table 2-2.—Possible Transistor Problems from Ohmmeter Readings

RESISTANCE READINGS PROBLEMS


FORWARD REVERSE The transistor is:
LOW (NOT SHORTED) LOW (NOT SHORTED) LEAKING
LOW (SHORTED) LOW (SHORTED) SHORTED
HIGH HIGH OPEN*
*Except collector-to-emitter test.
By now, you should recognize that the transistor used in figure 2-19 (view A, view B and view C)
is a PNP transistor. If you wish to test an NPN transistor for leakage, the procedure is identical to that
used for testing the PNP except the readings obtained are reversed.

When testing transistors (PNP or NPN), you should remember that the actual resistance values
depend on the ohmmeter scale and the battery voltage. Typical forward and reverse resistances are
insignificant. The best indicator for showing whether a transistor is good or bad is the ratio of forward-
to-reverse resistance. If the transistor you are testing shows a ratio of at least 30 to 1, it is probably
good. Many transistors show ratios of 100 to 1 or greater.

REFERENCE

Integrated Publishing, Inc. (n.d.). Retrieved from


http://electriciantraining.tpub.com/14179/css/Transistor-Testing-93.htm

You might also like