Guidelines for Project Submission
MCA/BCA/BSC-IT/PGDCA
The following suggested guidelines must be followed in preparing the Final project Report:
Good quality white executive bond paper A4 size should be used for typing and duplication. Care
should be taken to avoid smudging while duplicating the copies.
Page Specification :( Written paper and source code)
Left margin - 1.0 inch
Right margin- 0.75 inch
Top margin 0.75 inch
Bottom margin 0.75 inch
Page numbers - All text pages as well as Program source code listing should be
numbered at the bottom center of the pages.
Normal Body Text: Font Size: 12, Times New Roman, Double Spacing, Justified. 6 point
above and below para spacing
Paragraph Heading Font Size: 16, Times New Roman, Underlined, Left Aligned. 12 point
above & below spacing.
Paragraph Sub Heading Font Size: 14, Times New Roman, Underlined, Left Aligned. 12
point above & below spacing.
Chapter Heading Font Size: 20, Times New Roman, Centre Aligned, 30 point above and
below spacing.
Coding Font size : 10, Courier New, Normal
PROJECT PROPOSAL (SYNOPSIS) FORMAT
Project proposal should be prepared in consultation with the guide. It should clearly state the
objectives and environment of the proposed project to be undertaken. Project synopsis may contain
15-20 pages and sequence of contents strictly should be in the following order:
1) Cover and Title page
2) Index
3) Introduction and objective of the project
Introduction
Objective
Study of existing system, if any.
Product Definition
Problem Statement
4) Project Plan
Team Structure
Development Schedule
5) Analysis
Feasibility Analysis
DFD 0 Level, 1 Level and 2 Level( If Required)
ER Diagram
6) H/W and S/W Requirement
7) Table and Structure / Data Structure
8) Number of Modules & Detail of Modules
9) Types of Reports (If Any)
10) Scope of future application
11) Bibliography/References
Note: Synopsis must be submitted on time and must be in spiral binding.
SYNOPSIS
ON
REPORT TITLE
Department Of Computer Science
Microtek College of Management Technology
Murtazabad, Kerakat, Jaunpur (U.P)
Month, Year
Veer Bahadur Singh Purvanchal University, Jaunpur(U.P)
Under Esteemed Guidance Of
Guide Name
Submitted To: Submitted By:
Raj Kumar Singh(IT Co-Ordinator) Name 1 (Roll Number)
Sabab Ali Khan(Asst. IT Co-Ordinator) Name 2 (Roll Number)
Name 3 (Roll Number)
MCA/BCA/BSC-IT PROJECT REPORT FORMAT
The Project should be prepared in consultation with the guide and may contain 150-200 pages
(including coding). Project Report should strictly follow the points given below:
1) Cover and Title page + Inner Cover page
2) Index
3) Acknowledgement
4) Certificate of Originality
5) Introduction and objective of the project
Introduction
Objective
Study of existing system, if any.
Product Definition
Problem Statement
6) System Analysis
o Identification of Need
o Preliminary Investigation
7) Feasibility Study
o Technical Feasibility
o Economic Feasibility
o Operational Feasibility
9) Analysis
o DFD 0 Level, 1- Level and 2 Level
o ER Diagram
o Table structure
10) S/W & H/W Requirement Specification
11) System Design- Screen Shots
14) Coding
15) Implementation and Maintenance
16) Testing (Testing techniques and Testing strategies)
17) Various types of Reports/Modules
18) Pert Chart/Gantt Chart (If Any)
19) Future scope of the project
20) Conclusion
21) Bibliography/References
Note: - The above is meant to serve as a guideline for preparation of your project report. You may
add to, modify or omit some of the above-mentioned points depending upon their relevance
to your project. You may also consult your internal guide for the same.
Note: Student must submit the project report in Hard binding otherwise Project Report
will be rejected.
PROJECT
ON
REPORT TITLE
BY
NAME OF STUDENT
Course
ROLL NO
Department Of Computer Science
Microtek College of Management Technology
Murtazabad, Kerakat, Jaunpur (U.P)
Month, Year
Veer Bahadur Singh Purvanchal University
Jaunpur (U.P)
MAJOR/ MINOR PROJECT REPORT
ON
TITLE OF PROJECT
SUBMITTED IN PARTIAL FULFILLMENT FOR AWARD OF DEGREE
IN
BACHELOR OF COMPUTER APPLICATION
( BATCH 2015-2018 )
BY
NAME OF STUDENT
ROLL NO
UNDER THE ESTEEMED GUIDANCE OF
NAME OF GUIDE
Department Of Computer Science
Microtek College of Management Technology
Murtazabad, Kerakat, Jaunpur (U.P)
Month, Year
Veer Bahadur Singh Purvanchal University
Jaunpur
Certificate of Originality
I hereby declare that the Project entitled “Title of the Project” submitted to the Department
of Information Technology, Microtek College of Management & Technology Kerakat, Jaunpur
(U.P) in partial fulfillment for the award of the Degree of BACHELOR IN COMPUTER
APPLICATION in session 2015-2018 is an authentic record of my own work carried out under the
guidance of Dr./Ms./Mr.......................................... and that the Project has not previously formed
the basis for the award of any other degree.
Place:................ Signature of the candidate.
Date:................. (Name of Student)
(Roll No.)
This is to certify that the above statement made by the candidate is correct to the best of my
knowledge.
1. Signature of Internal guide 2. Signature of External Guide
Name:……………………………. Name:……………………………
Designation:………………............ Designation:…......................................
Acknowledgement
I am very grateful to my project guide Dr./Mr./Ms.__________________ for giving his
valuable time and constructive guidance in preparing the Synopsis/Project.
It would not have been possible to complete this project in short period of time without
his kind encouragement and valuable guidance.
Date: Signature
Name of the Student
