http://www.howtonetwork.
net
OSPF with Access List
Lab 2: OSPF with access-list
Lab exercise
Your task is to configure the network in Figure 19–2 to allow full connectivity using OSPF.
Router A is to block ICMP from Router C, and Router C is to deny any traffic on port 80.
Please feel free to try the lab without following the lab walk-through section.
Figure 19–2: OSPF with access-list
Text written in monospaced type indicates commands that can be entered on the router.
Purpose
A three-router lab is the typical scenario you will face in the CCNA exam. You must be comfortable
with configuring three routers with a basic config and then applying a routing protocol
and access-list.
Lab objectives
1. Use the IP-addressing scheme depicted in Figure 19–2.
2. Set telnet access for the router to use the local login permissions of username “banbury”
and the password “ccna”.
3. Configure the “enable password” to be “cisco”.
4. Configure IP addressing on all three routers.
5. Configure OSPF areas 0, 1, and 2.
6. Add an access-list on the serial interfaces of both routers A and C. Router A is to block
all ping traffic from network 192.168.2.0. Router C is to block all http traffic from
any network.
Lab walk-through
1. Follow the configuration from the previous lab.
2. Configure the access-lists on both Routers A and C and apply them to the serial interfaces.
RouterA(config)#
RouterA(config)#access-list 100 deny icmp 192.168.2.0 0.0.0.255 any
RouterA(config)#access-list 100 permit ip any any
RouterA(config)#interface serial 0
RouterA(config-if)#ip access-group 100 in
RouterC(config)#access-list 100 deny tcp any any eq 80
RouterC(config)#access-list 100 permit ip any any
RouterC(config)#ip http server
RouterC(config)#interface serial 0
RouterC(config-if)#ip access-group 100 in
3. Telnet from Router A to Router C. A normal telnet will work. However, a telnet on port
53 (DNS) will fail.
RouterA#telnet 192.168.2.2
Trying 192.168.2.2 ... Open
User Access Verification
Username: « Press Ctrl+Shift+6 (all together) and then “X”
RouterA#
RouterA#telnet 192.168.2.2 80
Trying 192.168.2.2, 80 ... Open
exit
HTTP/1.0 501 Not Implemented
Date: Mon, 01 Mar 1993 00:22:17 UTC
Content-type: text/html
Expires: Thu, 16 Feb 1989 00:00:00 GMT
<H1>501 Not Implemented</H1>
[Connection to 192.168.2.2 closed by foreign host]
4. Now ping Router A from Router C. The ping from the serial interface (the blocked network)
will fail. A ping from loopback 0 (10.0.0.1) will however, work.
RouterC#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
U.U.U
Success rate is 0 percent (0/5)
RouterC#ping
Protocol [ip]:
Target IP address: 192.168.1.1
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 10.0.0.1
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/64 ms
RouterC#
Show runs
RouterA#show run
Building configuration...
Current configuration : 900 bytes
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname RouterA
enable secret 5 $1$rujI$BJ8GgiK8U9p5cdfXyApPr/
username banbury password 0 ccna
ip subnet-zero
interface Loopback0
ip address 172.16.1.1 255.255.0.0
interface Loopback1
ip address 172.20.1.1 255.255.0.0
interface Ethernet0
no ip address
shutdown
interface Serial0
ip address 192.168.1.1 255.255.255.252
ip access-group 100 in
interface Serial1
no ip address
shutdown
!
router ospf 20
log-adjacency-changes
network 172.16.0.0 0.0.255.255 area 1
network 192.168.1.0 0.0.0.3 area 0
ip classless
no ip http server
access-list 100 deny icmp 192.168.2.0 0.0.0.255 any
access-list 100 permit ip any any
line con 0
password letmein
login
line 1 8
line aux 0
line vty 0 4
login local
end
---
RouterB#show run
Building configuration...
Current configuration : 827 bytes
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname RouterB
!
enable secret 5 $1$oXft$UMJZc/BQzbfpeHVCApF3H0
username banbury password 0 ccna
ip subnet-zero
interface Loopback0
ip address 172.30.1.1 255.255.0.0
interface Loopback1
ip address 172.31.1.1 255.255.0.0
interface Ethernet0
no ip address
shutdown
interface Serial0
ip address 192.168.1.2 255.255.255.252
clockrate 64000
interface Serial1
ip address 192.168.2.1 255.255.255.252
clockrate 64000
router ospf 20
log-adjacency-changes
network 192.168.1.0 0.0.0.3 area 0
network 192.168.2.0 0.0.0.3 area 0
ip classless
no ip http server
line con 0
password letmein
login
line aux 0
line vty 0 4
login local
end
RouterB#
---
RouterC#show run
Building configuration...
Current configuration:
version 11.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname RouterC
enable secret 5 $1$1AZx$UzhYsYlIpc7I4vJI3ZI4U.
username banbury password 0 cisco
ip subnet-zero
interface Loopback0
ip address 10.0.0.1 255.255.0.0
interface Ethernet0
no ip address
shutdown
!
interface Serial0
ip address 192.168.2.2 255.255.255.252
ip access-group 100 in
no ip mroute-cache
interface Serial1
no ip address
shutdown
router ospf 20
network 10.0.0.0 0.0.255.255 area 2
network 192.168.2.0 0.0.0.3 area 0
ip classless
access-list 100 deny tcp any any eq www
access-list 100 permit ip any any
line con 0
line 1 16
line aux 0
line vty 0 4
login local
end
RouterC#
© 2006-2011 HowtoNetwork.net All Rights Reserved. Reproduction without permission prohibited.
