NOTES

ROOF: CONCRETE ROOF TILES ON TRUSSES

- TILES ON 38x38mm BATTENS AT 320mm CENTRES MAX

EMBEDDED AT LEAST 300mm INTO BRICKWORK WITH CONNECTING DEVICES ACCORDING TO

TABLE L2, SCHEDULE 1, OF SABS 0400
-ALL WEB MEMBERS TO BE MINIMUM 38x114mm GRADE 4 WITH EQUAL BAYS SMALLER
THAN 1500mm. APPROVED BRACING MUST PREVENT BUCKLING AND KEEP TRUSSES UPRIGHT
-VALLEY AND HIP RAFTERS TO BE GRADE 6 50x228 SA PINE
-LAMINATED TIMBER TO COMPLY WITH SABS 876
-50mm GLASS FIBRE INSULATION TO BE INSTALLED ON CEILING

CONCRETE ROOF
-CONCRETE ROOF TO ENGINEER'S DETAIL WITH MINIMUM 50mm THICKNESS
-VERMICULITE SCREED GRADED TO 1:50 FALL TO 100m DIAMETER BILD IN DOWNPIPES

-WATERPROOFING BY SPECIALIST WITH A TEN YEAR GUARANTEE AS PER SPECIFICATION

FLOORS AND WATERPROOFING

-GROUND FLOOR SLAB=85mm THICK 20mpa CONCRETE PERFECTLY LEVEL AND AT
MINIMUM 150mm ABOVE GROUND LEVEL ON PROPERLY COMPACTED HARDCORE FILL
-25mm THICK SCREED AND FINISHES AS INDICATED
-SUSPENDED CONCRETE FLOOR SLABS TO ENGINEER'S DETAIL AND SPECIFICATIONS
-DPC UNDER ALL WALLS (EXCEPT FREE STANDING), FLOORS AND WINDOW SILLS
AND TO ALL VERTICAL CHANGES IN FLOOR LEVELS
-FLUSHINGS TO ALL PARAPETS AND CHANGES IN ROOF LEVELS

FROM CATCHPIT FITTED WITH GRATING AND SILT TRAP

-PLANTERS TO BE WATERPROOFED AND DRAINAGE INSTALLED

FOUNDATIONS, BRICKWORK & PARTITIONS

-ALL FOUNDATIONS TO BE 25mpa CONCRETE , AT LEAST 200x700mm. MINIMUM
200mm UNDER GROUND TO ENGINEER'S DETAILS AND SPECIFICATIONS
-BOUNDARY WALLS' FOUNDATION MUST NOT ENCROACH ON BOUNDARY AND WALLS
ARE TO BE PLASTERED AND PAINTED ON THEW INNER WALL
-PARAPET WALLS TO BE ATLEAST 300mmHIGH AND MAXIMUM 500mm WITH BRICKFORCE
IN EVERY COURSE
-ALL SCREEN WALLS TO BE AT LEAST 1800mm HIGH ABOVE GROUND LEVEL
-LINTOLS TO BE SUPPORTED MINIMUM 150mm FOR OPENINGS UPTO 4800mm.BRICKFORCE
TO BE BUILT IN EVERY COURSE BELOW FLOOR LEVEL AND ABOVE WINDOW LEVEL, EVERY
THIRD COURSE BETWEEN BETWEEN IN CONTINOUS BANDS
-NO TEETHING OR BLOCK BONDING WILL BE ALLOWED UNDER ANY CIRCUMSTANCES
-ANY PARTITION TO BE RODENT PROOF

STAIRS AND BALUSTRADES

-STAIRS TO BE 750mm MIN WIDTH, TREADS 300mm , RISERS 170mm WITH 6mm MAX DEVIATION
-1000mm HIGH BALUSTRADES TO ALL STAIRS AND BALCONIES
-MAX 3000mm VERTICAL RISE PER FLIGHT , WINDERS WHERE SHOWN ,TO BE AT LEAST 250mm
CONCRETE ROOF TRUSSES WIDE, 450mm FROM THE NARROW END AND ANGLE BETWEEN THE RISERS TO BE CONSTANT
ROOF NOTES -MINIMUM HEADROOM TO BE 2100mm MEASURED FROM PICHLINE
CONCRETE ROOF TILES TO MANUFACTURE'S SPECIFICATIONS
-GLASS BALUSTRADES (IF SHOWN ) TO BE SAFETY GLASS
AT 345 C/C MAXIMUM WITH '410 SISALATION' TO MANURACTURE'S
ON 114x38mm S.A PINE RAFTERS GLAZING
AT 760mm C/C MAX WITH 152x38mm S.A PINE TIE BEAM
114x38mm ROOF TRUSSES
AT 760mm C/C MAX WITH 114x38mm S.A PINE WALL PLATE
ALL WEB MEMBERS TO BE 114x38mm S.A PINE GRADE SIX

50 'ISOTHERM' MINERAL WOOL INSULATION

-BATHROOM WINDOWS TO BE FROSTED GLASS
38x38mm PINE BATTERNS
-ALL GLAZING ON DOORS TO BE SATETY GLASS
AT 345 C/C MAXIMUM -ALL GLAZED AREA LESS THAN 300MM ABOVE FFL TO BE COVERED WITH SATETY GLASS

AREA SCHEDULE
152x32mm TIE BEAM
NEW FLOOR AREA =
(CEILING JOIST)
50x38mmTILTING BATTERN SITE PLAN AREA =

SITE COVERAGE = %
38x38mm S.A BRANDERINGS
110mm INTERNAL BRICK WALL PLASTERED
& PAINTED TO CLIENT'S COLOUR CHOICE GLAZED EARTHENWARE
DISHED GULLEY CAST
10mm thick IN CONCRETE ngl CLEANING EYE ngl
BRICK CORBELLING DOORS & WINDOWS SCHEDULE
10mm SAND CEMENT PLASTER internal plaster
CORNICE TO CLIENT CHOICE
350 min

/ EQUALLY APPROAVED SEE SCHEDULE DRAWINGS OF DOORS AND WINDOWS

skirting to match 6.4mm THICK BY 900MM WIDE DO NOT SCALE THE DRAWINGS
floor finish pipe laid GYPSUM CEILING BOARD FIXED
25mm SAND to min 1:
40 fall
CEMENT SCREED ON 38x38mm BRANDERING
INTO BRICKWORK SPACED AT 450x900mm c/c FIXED
NATURAL GROUND 10mm THICK EXTERNAL ON 52x152mm CEILING JOIST \
10mm THICK INTERNAL
INVERT LEVEL=+450 mm. TIE BEAM
IF LESS ENCASE IN CONC PLASTER PLASTER

CHIMNEY/COWL -1000mm
ROOF NOTES ABOVE HIGHEST PITCH
TO COMPLY WITH NBR PART V V1-4 10mm thick 150mm thick
5440
internal plaster brick wall
38x38mm S.A PINE BATTERNS AT 345 C/C MAXIMUM CONCRETE ROOF TILES 5020mm roof apex DAMP PROOF MEMBRAINE
ON 114x38mm S.A PINE RAFTERS AT 760mm C/C MAX
WITH 152x38mm S.A PINE TIE BEAM AT FLOOR FINISH AS ON FLOOR PLAN 10mm thick
skirting to match external plaster
760mm C/C MAX WITH 114x38mm S.A PINE WALL PLATE
floor finish
ALL WEB MEMBERS TO BE 114x38mm 30mm SAND CEMENT SCREED damp proof
S.A PINE TO BE GRADE SIX trusses by specialist 85mm SURFACE BED membraine
25mm SAND BLINDING
6.4mm gypsum ceiling board 6.4mm gypsum
ceiling board 150mm WELL COMPACTED
HARDCORE
plaster & paint
220mm SOLID BRICK WALL PLASTERED
natural stone

& PAINTED INTERIOR & EXTERIOR

soil pipe less than
30mm THICK SCREED LAYED ON 1m deep
plaster & paint dpc
85mm THICK CONC SURFACE BED
dpc FFL dpc plaster & paint 600x230mm CONCRETE STRIP
FFL
FOUNDATION FOOTING
150mm WELL COMPACTED HARDCORE
UNDERNEATH THE SURFACE BED
600x230mm 600x230mm 600x230mm
concrete footing concrete footing concrete footing