SECTION 55 - ELECTRICAL SYSTEM 57

3. CONTROLS AND INSTRUMENTS

3.1 FRONT INSTRUMENT PANEL

1. DIRECTION INDICATOR LAMP 4. MAIN BEAM INDICATOR LAMP

This lamp lights up when the direction indicators This indicator lamp comes on when the main
are working. beam headlights are turned on.
2. BRAKE LIQUID LEVEL WARNING LAMP 5. “FOUR WHEEL STEER” (4WS) STEER INDI-
This lamp comes on and the audible warning CATOR LAMP
device sounds when the brake liquid is at mini- This lamp comes on when 4WS mode is select-
mum level. ed and phased.
3. SIDE LIGHTS AND LOW BEAM LAMP 6. “ROAD” (4WS) STEER INDICATOR LAMP
This lamp comes on when the side lights or low This lamp comes on when 2WS mode is select-
beam are activated. ed and phased.
58 SECTION 55 - ELECTRICAL SYSTEM

7. “CRAB” (4WS) STEER INDICATOR LAMP 17. 2/4WD SWITCH

This lamp comes on when crab steer mode is This switch is used to engage or disengage
selected and phased. 4WD.
The switch has three positions:
NOTE: If the three lamps come on at once this - first position (by pushing button on the right
means there is a problem with the electrical circuit. ):
Consult your Dealer. rear wheel drive with braking only on rear
wheels (lamp off).
8. SPEEDOMETER (optional) - second position (by pushing button on the left
The speedometer shows travel speed in kilom- ):
eters per hour (kmh) and miles per hour (mph). four wheels drive with braking on four wheels
9. DIFFERENTIAL LOCK SWITCH (Powershift (lamp on).
transmission) - third position (by pushing a second time button
This switch is used to lock or unlock the differen- on the left ):
tial. rear wheels drive and braking on four wheels.
10. ROTATING BEACON SWITCH
This switch is used to turn the rotating beacon NOTE: when the 4WD switch is in the “OFF” posi-
on or off (if fitted). tion and both brake pedals are operated together
11. LIGHT SWITCH the 4WD, will automatically be engaged (above 3
The switch has three positions: Km/h - 1.864 mph) to give 4WD braking and disen-
12. the first position is OFF; gage with brake pedals released.
13. the second position powers the gauge cluster,
the parking lights, the low beams indicator lamp 18. MANUAL MODE SELECTION SWITCH (Pow-
(3); ershift transmission)
14. the third position enables the main beams, pow- In situations where a MANUAL gear change (up
ers the low beams and main beams indicator or downshift) is required the powershift auto
lamp (4). change can be overridden by selection of this
15. HAZARD LIGHT SWITCH console mounted switch.
Press the control down to locked position. The
direction indicators and the control will flash si- NOTE: changing gears up or down must always be
multaneously. done using the Powershift transmission lever.
Press down again for the direction indicators
and control lamp to go out.
16. HAND-HELD AUXILIARY HYDRAULIC TOOL NOTE: when manual mode is no longer required,
CONTROLS (optional) place the control in OFF position to return to auto-
For instructions on how to use these controls. matic gear shifting.
 SECTION 55 - ELECTRICAL SYSTEM 59

3.2 CALIBRATION OF SPEEDOMETER

Dependent upon the model and tires fitted it may be

a requirement to set the calibration of the front con-
sole.
This setting is required if fitting a new instrument or
a change of tires takes place, and can be performed
by adjusting the settings of the switch block, mount-
ed at the rear of the console.

Each switch numbered 1 to 8 mounted in the block

should be turned ON = or OFF as shown
in the opposite example, to suit the requirement and
è
as shown in the following tables.
é
Switch positions: ê
1 = ON ë
0 = OFF ì
í
î
±² ï

Úîèêêê

POWERSHUTTLE

TIRE - ROLLING FREQUENCY AT SWITCH POSITIONS

AXLE RATIO
CIRCUMFERENCE 50 Km/hr 1-2-3-4-5-6-7-8
18.5 4065 - 4335 2055 1-1-1-1-0-1-0-0
18.5 3810 - 3911 2245 1-1-1-0-1-0-1-0
20.8 4065 - 4335 2310 1-1-1-0-1-1-1-0
20.8 3810 - 3911 2522 1-1-0-0-0-0-0-1

POWERSHIFT

TIRE - ROLLING FREQUENCY AT SWITCH POSITIONS

EGS FREQUENCY
CIRCUMFERENCE 50 Km/hr 1-2-3-4-5-6-7-8
6.53 - 6.12 4065 - 4335 315 Hz 0-0-0-0-0-0-0-0
6.97 - 6.79 3810 - 3911 345 Hz 0-1-0-0-0-1-0-0
60 SECTION 55 - ELECTRICAL SYSTEM

3.3 SIDE INSTRUMENT PANEL

1. FRONT WORK LIGHTS SWITCH 4. GLIDE RIDE SYSTEM CONTROL SWITCH

This switch has 3 positions: (Optional)
- 1st position = OFF. The glide ride system control improves the ma-
- 2nd position = the two frontal outer working chine behaviour during travel, regardless of the
lights turn on. type of terrain and with the loader bucket full or
- 3rd position = the two front inner working lights empty. It reduces forward and rearward pitching
turn on. when moving to the rear or forwards and when
The lights switch turns on only in the second carrying loads, at the same time increasing pro-
and third position. ductivity and operator comfort. It also minimises
2. HYDRAULIC SPEED CONTROL SWITCH (If impact forces to which the machine may be sub-
fitted) jected.
3. SWITCH FOR PILOT LOADER (Optional) Do not use this system during the digging and
loading operations with the front loader.

WARNING
Never operate the glide ride system control when
the loader arm and loader bucket are maintaining
the front of the machine raised off the ground. The
machine could fall and cause serious or fatal injury.
 SECTION 55 - ELECTRICAL SYSTEM 61

5. LOADER ATTACHMENT LOCKING SWITCH 11. BACKHOE ATTACHMENT SIDESHIFT CAR-

(Optional) RIAGE LOCKING AND UNLOCKING SWITCH
When operated, this switch is for preventing any (sideshift backhoe version)
movement of the loader attachment during travel. This switch has 2 positions:
6. SIDE INSTRUMENT (See side instrument) The switch is used to lock or unlock the backhoe
7. UP/DOWN SWITCH attachment sideshift carriage to allow lateral shift-
By means of this control you can scroll the option ing.
of menu or data shown by the display of the diag- 12. REAR WORK LIGHTS SWITCH
nostics. This switch has 3 positions:
8. MENU ENTER SWITCH - 1st position = OFF.
By means of this control you can visualize and - 2nd position = the two rear outer working lights
confirm the options of menu show on the display. turn on.
9. REAR WINDSHIELD WIPER AND WASHER - 3rd position = the two rear inner working lights
SWITCH turn on.
The wiper is activated when the switch is de- The lights switch turns on only in the second and
pressed and will remain in function until the switch third position.
is returned to the “OFF” position.
The washer is operated by further depressing and NOTE: Never use the working lights during road trav-
holding switch. When the switch is released the el.
wash will stop and return to the wipe position.
10. BACKHOE ATTACHMENT LOCKING SWITCH
(Optional)
The switch is used to lock or unlock the backhoe
attachment locking plate in preparation for road
travel.
62 SECTION 55 - ELECTRICAL SYSTEM

SIDE INSTRUMENT

1. CAUTION MASTER LAMP 4. BATTERY CHARGE WARNING LAMP

This lamp signals a not critical caution. This warning lamp comes on when the alterna-
When this caution is “active”, it is necessary to tor/fan belt is broken or when the alternator is
change the operating mode, plan a down time to not charging the battery. If the lamp comes on
carry out maintenance or, if the fault continues, when the machine is working, move the ma-
consult your dealer. chine to a place of safety, stop the engine, re-
This lamp lights up at the same time of lamps move the starter switch key and find the cause
(2), (4), (6), (7) and (10). of the problem.
2. ENGINE OIL PRESSURE WARNING LAMP 5. PARKING BRAKE INDICATOR LAMP
This warning lamp comes on and the audible This indicator lamp comes on when the parking
warning device sounds when the engine oil brake lever is in the raised position (wheels
pressure is too low. If the lamp comes on when braked).
the machine is working, move the machine to a 6. AIR FILTER RESTRICTION WARNING LAMP
place of safety, stop the engine, remove the This warning lamp comes on when the air filter
starter switch key and find the cause of the prob- primary element is to be cleaned or replaced.
lem. 7. TRANSMISSION OIL PRESSURE WARNING
3. STOP MASTER LAMP LAMP
The stop master lamp signals a critical caution. This lamp lights up and the audible alarm
When this lamp lights up, stop the machine im- sounds when the transmission oil pressure is
mediately and shut off the engine. too low. If the lamp comes on when the machine
If this is not the case, the machine can get dam- is working, move the machine to a place of safe-
aged or accidents may occur. ty, stop the engine, remove the starter switch
key and find the cause of the problem.
 SECTION 55 - ELECTRICAL SYSTEM 63

8. AIR CONDITIONER INDICATOR LAMP (Option- 14. ENGINE REVOLUTIONS COUNTER

al) The revolutions counter shows the engine speed
This lamp comes on when the air conditioner is in revolutions per minute.
working. The figures indicated must be multiplied by 100.
9. GRID HEATER INDICATOR LAMP (If fitted) Each intermediate mark shows a value of 100 rpm.
This lamp lights up while the engine is being pre- We recommend not to reach the red field.
heated. 15. TRANSMISSION OIL TEMPERATURE INDICA-
10. LOW FUEL LEVEL WARNING LAMP TOR
This warning lamp comes on when the fuel level is This indicator shows the transmission oil tempera-
low. You have approximately an hour to fill the fuel ture. When the temperature is normal, the needle
tank. is in the grey area. If the needle is in the red area,
change down to a lower gear. If the needle still re-
NOTE: when the starter switch key is in the “ON” all mains in the red area, stop the machine travel,
lamps light up and the instrument buzzer sounds for 5 place the gear change lever and the direction of
seconds. Afterward the lamps light off and only lamp travel control lever in the neutral position and
(2) remain alight. The gauges (11) and (12) set to po- leave the engine running at 1000 rpm. If this oper-
sition. ation does not enable the oil temperature to be re-
duced, check the gearbox oil level and make sure
11. FUEL LEVEL GAUGE that the radiator and oil cooler are perfectly clean.
This gauge shows the quantity of fuel in the fuel 16. ENGINE COOLANT SOLUTION TEMPERATURE
tank. INDICATOR
12. BATTERY CHARGE INDICATOR This indicator shows the temperature of the engine
This indicator shows the state of charge of the bat- coolant solution. When the temperature is normal,
tery. At normal charge the needle should be in the the needle is in the grey area. If the needle is in the
grey area. If the needle is in the left red area, this red area the audible warning sounds. Move the
shows that the battery charge is insufficient or that machine to a place of safety, stop the engine, re-
the alternator is not charging the battery. If the move the starter switch key and check the coolant
needle is in the right red area, this indicates exces- solution level. Make sure that the radiator and oil
sive battery charge which may cause damage to cooler are perfectly clean and that all the thermo-
the battery. stats function correctly.
13. DIAGNOSTICS DISPLAY
By means of this display it is possible to visualize
the various data of diagnostics. The service hours
performed are indicated steadily.