JOB NO. ITEM NO.

Amoco Corporation PURCHASE ORDER NO.

SPECIFICATION NO.
MONITORING SYSTEM REVISION NO. DATE
DATA SHEET (API 670-3RD) PAGE 1 OF 4 BY

1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT DATE REVISION

2 FOR UNIT

3 SITE

4 SERVICE

5 INSTRUMENT MANUFACTURER

6 NOTE: INDICATES INFORMATION TO BE COMPLETED BY PURCHASER BY MACHINERY VENDOR

7 BY PURCHASER OR MACHINERY VENDOR

8 MACHINERY TRAIN COMPONENTS OPERATING ENVIRONMENT

9 NUMBER OF: STANDARD COMPONENTS (2.2.4.1)

10 PUMPS ROTARY COMPRESSORS SPECIFIED CHEMICALS (2.2.4.2)

11 STEAM TURBINES GEAR UNITS

12 GAS TURBINES ELECTRIC MOTORS PROBE DATA (3.1.1)

13 CENTRIFUGAL COMPRESS'RS OTHER(DESCRIBE) STD. 4.8 TO 5mm TIP DIA. WITH 1.0 METER INTEGRAL CABLE (3.1.1.2)

14 OPTIONAL PROBES WITH THE FOLLOWING STANDARD

15 SCOPE OF RESPONSIBILITIES OPTIONS: (3.1.1.3)

16 APPENDIX B 7.6 TO 7.9mm (0.300 TO 0.312 INCHES)

17 FINAL INSTALLATION PROBE TIP WITH 3/8-24-UNF-2A PROBE THREADS (3.1.1.3a)

18 MONITORS REVERSE MOUNT, INTEGRAL HEX NUT PROBE BODY (3.1.1.3b)

19 SIGNAL CABLES TIP DIAMETER OF 7.6 TO 7.9mm WITH M10 METRIC THREADS

20 TRANSDUCERS & SENSORS (3.1.1.3c)

21 APPENDIX F REQUIREMENTS TIP DIAMETER OF 4.8 TO 5.0mm WITH M8 METRIC THREADS

22 (3.1.1.3d)

23 SCOPE OF SUPPLY LENGTHS OTHER THAN APPROXIMATELY 25mm (1 INCH)

24 TRANSDUCERS (3.1.1.3e)

25 SENSORS FLEXIBLE STAINLESS STEEL ARMORING ATTACHED TO THE

26 MONITORS PROBE BODY AND EXTENDING TO APPROXIMATELY 100mm

27 (4 INCHES) OF THE CONNECTOR (3.1.1.3f)

28 SITE DATA OTHER (DESCRIBE)

29 DESIGN TEMP, °C OR °F SUMMER MAX WINTER MIN

30 DESIGN WET BULB TEMP. °C OR °F

31 WINTERIZATION REQUIRED

32 TROPICALIZATION REQUIRED

33 UNUSUAL CONDITIONS

34 DUST

35 FUMES NUMBER OF PROBES IN TRAIN

36 OTHER (DESCRIBE) STANDARD COMPLEMENT (APPENDIX H)

37 NONSTANDARD COMPLEMENT REQUIRED

38 ELECTRICAL EQUIPMENT HAZARD CLASS PRIMARY RADIAL

39 CLASS GROUP DIVISION SPARE RADIAL

40 RADIO FREQUENCY INTERFERENCE (3.8.4) PRIMARY AXIAL

41 SPARE AXIAL
PHASE REFERENCE

42 OPERATING TEMPERATURE RANGE PHASE REFERENCE

43 STANDARD, ALL COMPONENTS(2.2)

45 PROBE & EXTENSION CABLE °C OR °F FROM TO RADIAL TRANSDUCERS

46 OSCILLATOR-DEMODULATOR °C OR °F FROM TO STANDARD ARRANGEMENT (4.1.1)

47 TEMP. SENSOR & LEAD °C OR °F FROM TO DEVIATION FROM STANDARD RADIAL PROBE ARRANGEMENT

48 MONITOR AND POWER SUPPLY °C OR °F FROM TO REQUIRED: (DESCRIBE)

49 ACCELEROMETER °C OR °F FROM TO

50 CHARGE AMPLIFIER °C OR °F FROM TO

51

06/95 EF-050-47.51 SHT 1 OF 4 API670.XLS REV 1

Amoco Corporation
JOB NO. ITEM NO.
MONITORING SYSTEM REVISION NO. DATE
DATA SHEET (API 670-3RD) PAGE 2 OF 4 BY

1 PROBE ARRANGEMENT (APPENDIX H) (CON'T) PIEZO ELECTRIC ACCELEROMETER DATA (3.2) (CON'T)

2 AXIAL TRANSDUCERS STANDARD 5 METER (200 INCH) ACCELEROMETER EXTENSION

3 STANDARD SHAFT END OR INTEGRAL AXIAL SURFACE CABLE (3.2.2.3)

4 OPTIONAL ONE PROBE ON SHAFT & ONE PROBE ON INTEGRAL OTHER (DESCRIBE) (m) (INCHES)

5 THRUST COLLAR EXTENSION CABLE PROTECTION (4.2.3.4)

6 OTHER (DESCRIBE) STANDARD CONDUIT

7 OPTIONAL WEATHERPROOF FLEXIBLE ARMOR

8 PROBES MOUNTED TO MEASURE INCREASING GAP FOR NUMBER OF ACCELEROMETERS PER BEARING

9 NORMAL OPERATION (3.5.5.5) NUMBER OF CHANNELS IN TRAIN

10 PROBES MOUNTED TO MEASURE DECREASING GAP FOR CHARGE AMPLIFIER DATA

11 NORMAL OPERATION (3.5.5.5) INSTRUMENT MANUFACTURER'S MODEL NO.

12 PHASE REFERENCE TRANSDUCERS/ONE EVENT PER REVOLUTION DIMENSIONS (mm) (INCHES) X X

13 DRIVER TEMPERATURE SENSOR DATA (3.3.1)

14 GEARBOX SENSORS NOT REQUIRED

15 INPUT SHAFT STANDARD GROUNDED, TYPE J IRON/COPPER-NICKEL

16 OUTPUT SHAFT (CONSTANTAN) THERMOCOUPLE

17 DRIVEN EQUIPMENT OPTIONAL 100 OHM, PLATINUM, THREE-LEAD RTD'S, WITH A

18 OTHER (DESCRIBE) TEMPERATURE COEFFICIENT OF RESISTANCE EQUAL TO

19 0.00385 OHM/OHM/°C

20 EXTENSION CABLE DATA (3.1.2) OTHER (DESCRIBE)

21 STANDARD 4.0 METER (160 INCHES) LENGTH, NONARMORED FLEXIBLE STAINLESS STEEL OVERBRAIDING ON LEADS (3.3.1.2)

22 4.0 METER (160 INCHES) LENGTH, ARMORED (4.2.1.4)

23 CABLE CONNECTOR ELECTRICAL ISOLATION (4.2.1.4) TEMPERATURE SENSOR MOUNTING

24 INSULATING SLEEVE EMBEDDED SENSORS

25 INSULATING WRAP (DESCRIBE) SPRING-LOADED SENSORS (BAYONET TYPE) (4.2.5.3)

26 OTHER (DESCRIBE)

27 OTHER (DESCRIBE) ELECTRICALLY INSULATED FROM BEARING (4.2.5.5)

28

29 PIEZO ELECTRIC ACCELEROMETER DATA (3.2)

30 GENERAL: RADIAL BEARING TEMPERATURE SENSOR ARRANGEMENT

31 INSTRUMENT MANUFACTURER'S MODEL NO. SENSORS REQUIRED

32 ACCELEROMETER POWER REQMT 24 VDC (mA) SENSORS NOT REQUIRED

33 EXTERNAL CHARGE AMPLIFIER SLEEVE TYPE, L/D RATIO > 0.5 (4.1.5.1.2)

34 SPECIAL BODY MATERIAL SLEEVE TYPE, L/D RATIO £ 0.5 (4.1.5.1.3)

36 TRANSDUCER MOUNTING: TILT-PAD TYPE, L/D RATIO £ 0.5 (4.1.5.1.6)

37 API APPENDIX FIGURE: C1 C2 C3 C4 LOAD-ON PAD (4.1.5.1.7)

38 OTHER LOAD-BETWEEN-PADS (4.1.5.1.8)

39 STANDARD MOUNTING/STANDARD ACCELEROMETER (3.2.1) OTHER (DESCRIBE)

40 ACCELEROMETER WITH THE FOLLOWING OPTIONS: (3.2.1.4)

41 CENTER-POST MOUNTING - ENGLISH THREADS OTHER

42 THAN 1/4-28 UNF (3.2.1.4a) THRUST BEARING TEMPERATURE SENSOR ARRANGEMENT

43 SPECIFY THREADS SENSORS REQUIRED

44 CENTER-POST MOUNTING - METRIC THREADS (3.2.1.4b) SENSORS NOT REQUIRED

45 SPECIFY THREADS STANDARD TWO SENSORS IN ACTIVE BEARING

46 THREE OR FOUR-BOLT FLANGE MOUNTING (3.2.1.4c) SENSORS DEGREES APART

47 SIDE CONNECTOR (3.2.1.4d) STANDARD TWO SENSORS IN INACTIVE BEARING

48 INTEGRAL EXTENSION CABLE (3.2.1.4e) SENSORS DEGREES APART

49 ACCELEROMETER MOUNTING BLOCK (3.2.1.4f) OTHER (DESCRIBE)

50 INTEGRAL CENTER POST(3.2.1.4g)

06/95 EF-050-47.51 SHT 2 OF 4 API670.XLS REV 1

Amoco Corporation
JOB NO. ITEM NO.
MONITORING SYSTEM REVISION NO. DATE
DATA SHEET (API 670-3RD) PAGE 3 OF 4 BY

1 MONITOR & POWER SUPPLY DATA RADIAL SHAFT VIB.T'N & AXIAL POSTION CHANNEL (CON'T)

2 MONITOR MOUNTING DIMENSIONS (mm) (INCHES) DISPLAY OUTPUT

3 HEIGHT WIDTH DEPTH MEASURED VALUE AS A PERCENT OF

4 LOCATION INDOOR OUTDOOR ALARM (ALERT) AND SHUTDOWN

5 INPUT VAC Hz (DANGER) VALUES TO 1% RESOLUTION

6 VDC TRANSDUCER OK LIMITS

7 OUTPUTS HARDWARE AND SOFTWARE

8 STANDARD 4 TO 20 mA ZERO TO TEN VOLTS DC DIAGNOSTICS

9 ANALOG DIGITAL OUTPUT GRAPHIC COMMUNICATIONS LINK STATUS

10 OTHER (DESCRIBE) ALARM SETPOINTS

11 TAMPERPROOF SHUTDOWN DISARM WITH LIGHT EMITTING GAP VOLTAGE

12 DIODE (3.5.1.5) TIME STAMP AND DATE ALL

13 RELAYS TRANSMITTED DATA

14 ALARM (ALERT) LOG OF SYSTEM ENTRY TO

15 STANDARD NORMALLY ENERGIZED INCLUDE DATA, TIME, INDIVIDUAL

16 OPTIONAL NORMALLY DEENERGIZED ACCESS CODE AND RECORD OF

17 SHUTDOWN (DANGER) CHANGES

18 STANDARD NORMALLY DEENERGIZED OTHER (DESCRIBE)

19 OPTIONAL NORMALLY ENERGIZED

20 TACHOMETER (3.5.1.3)

21 RADIAL SHFT VIB.T'N & AXIAL POST'N CHN'L (3.5.3&3.5.5) TACHOMETER NOT REQUIRED

22 TYPE OF DISPLAY NUMBER OF PROBES MONITORED TACHOMETER REQUIRED

23 ANALOG RADIAL ABILITY TO RECORD/STORE HIGHEST SPEED

24 DIGITAL AXIAL CONTROLLED ACCESS RESET REQUIRED

25 LIQUID CRYSTAL DIODES BEARING TEMPERATURE CHANNEL (3.5.6)

26 LIGHT EMITTING DIODES MONITOR CONFIGURATION

28 READOUT RANGE NUMBER OF BEARINGS MONITORED

29 RADIAL DISPLAY (3.5.3.1) AXIAL DISPLAY RADIAL

30 STANDARD 0 TO 125 MICROMTRS -1.0 TO +1.0 MICRO- ACTIVE THRUST

31 STANDARD 0 TO 5 MILS METERS INACTIVE THRUST

32 OPTIONAL 0 TO 250 MICROMTRS -40 TO +40 MILS OTHER (DESCRIBE)

33 OPTIONAL 0 TO 10 MILS OTHER (DESCRIBE)

34 OTHER (DESCRIBE) TYPE OF DISPLAY

35 STANDARD DIGITAL

36 SHUTDOWN SYSTEM LIQUID CRYSTAL DIODES

37 STANDARD DUAL VOTING LOGIC LIGHT EMITTING DIODES

38 SINGLE CHANNEL OTHER

39 SHUTDOWN BYPASS EACH CHANNEL (3.5.1.5) OTHER

40 READOUT RANGE

41 ADDITIONAL DISPLAY AND/OR DIGITAL OUTPUTS (3.5.1.2) STANDARD 0°F TO +300°F

42 DISPLAY OUTPUT OPTIONAL 0°C TO +150°C

43 CHANNEL ALARM STATUS OTHER (DESCRIBE)

44 ARMED/DISARMED SHUTDOWN STATUS SHUTDOWN SYSTEM

45 FOR ALL MACHINES STANDARD DUAL VOTING LOGIC

46 ALARM STORAGE FOR STORING THE EACH RADIAL BEARING

47 TIME, DATE, AND VALUE FOR A ACTIVE THRUST BEARINGS

48 MINIMUM OF 64 ALARMS INACTIVE THRUST BEARINGS

49 CHANNEL VALUE +/- 0.5% FULL-SCALE OTHER (DESCRIBE)

50 RANGE RESOLUTION

51 SINGLE CHANNEL

06/95 EF-050-47.51 SHT 3 OF 4 API670.XLS REV 1

Amoco Corporation
JOB NO. ITEM NO.
MONITORING SYSTEM REVISION NO. DATE
DATA SHEET (API 670-3RD) PAGE 4 OF 4 BY

1 CASING VIBRATION CHANNEL (3.5.4) TESTING INSPECTION AND PREP FOR SHIPMENT (SEC 5)

2 CASING VIBRATION NOT REQUIRED FIELD TESTING PER APPENDIX F

3 CASING VIBRATION REQUIRED INSPECTION REQUIRED OF MONITORING SYSTEM IN INSTRUMENT

4 NUMBER OF ACCELEROMETERS MONITORED MANUFACTURERS FACILITY

5 STANDARD MONITOR (3.5.4.1) 10 DAY NOTICE REQUIRED BEFORE TEST

6 OPTIONS (3.5.4.2) MONITORING SYSTEM TO BE USED DURING MECHANICAL

7 MONITOR AND DISPLAY EITHER ACCELERATION OR RUNNING TEST (DESCRIBE EXTENT TO BE USED).

8 VELOCITY (SPECIFY)

9 MONITOR AND DISPLAY TWO CHANNELS OF ACCELER'TN

10 AND/OR VELOCITY (SPECIFY)

11 ALTERNATE FILTER AND/OR FREQ'NCY RANGES (SPECIFY)

12

13 MONITOR AND DISPLAY IN TRUE RMS PROBES CALIBRATED TO INSTALLED PROBE TARGET AREA (5.6.2.1)

14 ALTERNATE FULL-SCALE RANGES (SPECIFY) MISCELLANEOUS

15 DUAL VOTING LOGIC SPECIAL PACKING, SEALING, MARKING OR STORAGE REQUIREMENTS:

16 OTHER (DESCRIBE) DESCRIBE:

17

18
19 SYSTEM WIRING & CONDUIT (3.6)

20 VIBRATION & POSITION SIGNAL CABLE

21 SINGLE CIRCUIT CABLE (APPENDIX D.2)

22 MULTIPLE-CIRCUIT CABLE (APPENDIX D.3)

23 TEMPERATURE SIGNAL CABLE

24 SINGLE CIRCUIT THERMOCOUPLE (APPENDIX D.4)

25 OTHER (DESCRIBE)

26

27 OSCILLATOR-DEMODULATOR MOUNTING BOXES

28 ONE PER MACHINE CASE

29 TWO PER MACHINE CASE

30 OTHER (DESCRIBE)

31

32 FIELD-INSTALLED INSTRUMENTS (3.8) REMARKS:

33 LOCATION INDOOR OUTDOOR

34 HOUSING/MOUNTING BOX

35 NEMA TYPE

36 DRY AIR PURGE REQUIREMENTS (3.8.2)

37 NONE REQUIRED

38 REQUIRED PER ISA-512.4 & NFPA 496

39 TYPE X

40 TYPE Y

41 VENDOR'S DATA (SEC 6)

42 NO. OF COPIES OF REQUIRED DOCUMENT

43 REQUIRED BY (SPECIFY DATE)

44 NO. OF PRINTS AND/OR REPRODUCIBLES REQUIRED

45 REQUIRED BY (SPECIFY DATE)

46 OTHER (DESCRIBE)

47

48

49

50

51

06/95 EF-050-47.51 SHT 4 OF 4 API670.XLS REV 1