Scribd
Upload
88 views

Batangas State University

The document describes an experiment on operational amplifiers. The objectives are to construct and measure a summing amplifier and a difference amplifier. The procedures describe implementing circuits for a summing amplifier and difference amplifier on an analog trainer. Key steps include connecting input voltages, measuring the output voltages, and drawing conclusions. The conclusion states that a summing amplifier combines input voltages into a single output, while a difference amplifier amplifies the difference between inputs but suppresses voltages common to both inputs.

Uploaded by

Ian Ronquillo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
88 views

Batangas State University

The document describes an experiment on operational amplifiers. The objectives are to construct and measure a summing amplifier and a difference amplifier. The procedures describe implementing circuits for a summing amplifier and difference amplifier on an analog trainer. Key steps include connecting input voltages, measuring the output voltages, and drawing conclusions. The conclusion states that a summing amplifier combines input voltages into a single output, while a difference amplifier amplifies the difference between inputs but suppresses voltages common to both inputs.

Uploaded by

Ian Ronquillo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Republic of the Philippines

BATANGAS STATE UNIVERSITY


Pablo Borbon Main Campus II
Alangilan, Batangas City
College of Engineering, Architecture and Fine Arts
Electronics Engineering Program

Chapter 3 – Operational Amplifiers

Experiment 3.3 – Summing and Difference Amplifiers

Objectives

- Constructing and measuring a summing amplifier


- Constructing and measuring a difference amplifier

Procedures

Step 1: Connect the analog trainer to the power supply and the power supply to the Mains.

Summing Amplifier

Step 2: Implement the following circuit on the main plug in board.

Circuit for single power supply:

Step 3: Turn on the trainer.


Step 4: Connect V2 to +12V terminal.

Step 5: Connect V1 to the variable voltage source.

Step 6: Change the input voltage V1 and measure the output voltage Vo and fill the following table.

No. 1 2 3 4 5 6 7 8 9 10 11 12 13
V1 -3.5 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 3
Vo 10.35 10 9.90 10.8 10.23 10.3 10.19 9.90 9.9 9.85 10.03 9.94 9.83

Step 7: Draw your conclusions.

Step 8: connect the V1 terminal to the operational amplifier to the ouput terminal of the function
generator. Adjust the function generator to 3Vp-p 1kHz sine wave.

Step 10: Plot the scope picture on the following graph

Difference Amplifier

Step 11: Implement the following circuit.

Step 12: Connect V2 to +12V terminal.


Step 13: Connect V1 to the variable voltage source.

Step 14: Change the input voltage V1 and measure the output voltage Vo and fill the following table.

No. 1 2 3 4 5 6 7 8 9 10 11 12 13
V1 -3.5 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 2 2.5 3
Vo 3.79 3.35 3.28 3.06 2.8 2.6 2.35 2.1 1.83 1.64 1.38 1.14 0.86

Step 15: Draw your conclusions.

Step 16: Connect the V1 terminal to the operational amplifier to the ouput terminal of the function
generator. Adjust the function generator to 8Vp-p 1kHz sine wave.

Step 17: Plot the scope picture on the following graph.

Conclusion:

According the experiment done, the group concluded that, Summing amplifier is a type of
operational amplifier configuration that is used to combine the voltages present on the two or more
inputs into a single output voltage. While, a difference amplifier is a type of electronic amplifier that
amplifies the difference between two input voltages but suppresses any voltage in common to the two
inputs.

You might also like