Scribd
Upload
442 views

019-043 Engine Wiring Harness: General Information

Diagrama eléctrico motor

Uploaded by

sanach
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
442 views

019-043 Engine Wiring Harness: General Information

Diagrama eléctrico motor

Uploaded by

sanach
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Engine Wiring Harness https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/8...

019-043 Engine Wiring Harness

General Information

The ISM and QSM engines use


separate wiring harnesses to control
the engine and some of the vehicle
operations. There are three connectors
for the wiring harnesses. In the picture
shown, the following harnesses
connect to the ECM from right to left:

1. Sensor harness
2. Actuator harness
3. OEM harness.

Remove

Disconnect the harness from the


sensors and switches.

1. Intake manifold pressure sensor


2. Intake manifold temperature
sensor
3. Crankshaft or camshaft position
sensor
4. Coolant temperature sensor
5. Fuel shutoff solenoid
6. 15-pin pass-through connector

1 de 4 13/04/2010 15:04
Engine Wiring Harness https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/8...

7. Centinel™ connector (if


equipped)
8. Ambient air pressure sensor
9. Oil pressure/temperature sensor
10. Wet tank pressure sensor
11. Water-in-fuel sensor
12. Wastegate controller
13. Fuel inlet restriction sensor (if
equipped).

Disconnect the 31-pin Deutsch


connector from the OEM side of the
wiring harness.

Remove the harness clamps from the


support bracket of the engine block.

Disconnect the engine harnesses from


the ECM.

Inspect for Reuse

Replace or repair the engine harness if


there is an open circuit or a short circuit
found under the protective covering of
the harness body.

2 de 4 13/04/2010 15:04
Engine Wiring Harness https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/8...

Install

Connect the engine harnesses to the


ECM.

Torque Value: 2.8 n.m [25 in-lb]

Connect the harnesses to the sensors


and switches.

1. Intake manifold pressure sensor


2. Intake manifold temperature
sensor
3. Crankshaft or camshaft position
sensor
4. Coolant temperature sensor
5. Fuel shutoff solenoid
6. 15-pin pass-through connector

7. Centinel™ connector (if


equipped)
8. Ambient air pressure sensor
9. Oil pressure/temperature sensor
10. Wet tank pressure sensor
11. Water-in-fuel sensor
12. Wastegate controller
13. Fuel inlet restriction sensor (if
equipped).

Connect the 31-pin Deutsch connector


to the engine harness.

Install the harness clamps that hold


the engine harness to the block.

3 de 4 13/04/2010 15:04
Engine Wiring Harness https://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/8...

Last Modified: 28-Jun-2002

Feedback / Help
Copyright © 2000-2010 Cummins Inc. All rights reserved.

4 de 4 13/04/2010 15:04

You might also like