Technical Data Sheet
Additin® EP Additive
RC 2540
Type
EP additive; low viscosity, light coloured, active sulphur carrier
Technical data*
Composition dialkylpentasulphide
Appearance light coloured, low viscosity liquid
Colour (ASTM-D 1500) typ. 2.5
Sulphur approx. 40 % weight
Active sulphur (ASTM-D 1662) approx. 36 % weight
Copper corrosion (ASTM-D 130)
2.5 % weight Additin RC 2540 in
a paraffinic base oil, 3 h/100 °C 3b - 4b
Viscosity, 40 °C (ASTM-D 445) approx. 45 mm²/s
Density, 20 °C (ASTM-D 1298) approx. 1.0 g/l
Flash point, COC (ASTM-D 92) approx. 150 °C
Application
- water miscible metalworking fluids
- neat metalworking fluids
The use of Additin RC 2540 is a good alternative to the sulphurization of base oils with elementary sulphur.
In addition, Additin RC 2540 shows with increasing temperatures a steadily increasing active sulphur level (up to
max. 38 %) resulting in an effective EP activity at only slightly elevated temperatures (50 to 60 °C).
Additin RC 2540 can be successfully combined with other sulphur carriers such as Additin RC 2415 in order to
increase EP activity.
The antiwear effect is improved by combination of Additin RC 2540 with zinc
dithiophosphates, e.g. Additin RC 3038, phosphoric acid partial esters or ashless phosphorus-sulphur additives
e.g. RC 3880
Solubility
Soluble in mineral oils and synthetic base oils. However, it is necessary to verify the solubility in the base oils
used and the compatibility with other additives.
Test results
Paraffinic base oil, ISO VG 15
base oil, + 2 % b. w. + 5 % b. w. + 10 % b. w. + 15 % b. w.
no additives RC 2540 RC 2540 RC 2540 RC 2540
Page Version: Revised: Printed on:
1 of 3 1/01. Apr 99 01-15-2015 01-15-2015
Four-ball test
(DIN 51350, part 2)
weld load 600 - 700 N 2200 - 2400 N 2400 - 2600 N 2600 - 2800 N 2800 - 3000 N
Four-ball test
(DIN 51350, part 3)
1 h/300 N
scar diameter
0.70 mm 0.80 mm 1.00 mm 1.20 mm 1.50 mm
Four-ball test
(ASTM D-2783)
weld point 320 kg
LWI 53 kg
Load-carrying test
according to Brugger approx. approx. approx. approx.
load capacity < 20 N/mm² 65 N/mm² 65 N/mm² 65 N/mm² 80 N/mm²
Falex Pin and Vee
ASTM D-2670-88
load value 3500 lbs 4500 lbs
Packing unit
200 kg bunghole drums
Storage conditions
Storage temperature: approx. 20 °C; protect from heat and frost!
Shelf life: approx. 12 months
Handling
Consult material safety data Sheet (MSDS)
for additional handling information on Additin RC 2540.
Page Version: Revised: Printed on:
2 of 3 1/01. Apr 99 01-15-2015 01-15-2015
Our technical advice - whether verbal, in writing or by way of trials - is given in good faith but without warranty, and this also applies where
proprietary rights of third parties are involved. It does not release you from the obligation to test the products supplied by us as to their
suitability for the intended processes and uses. The application, use and processing of the products are beyond our control and, therefore,
entirely your own responsibility. Should, in spite of this, liability be established for any damage, it will be limited to the value of the goods
delivered by us and used by you. We will, of course, provide products of consistent quality within the scope of our General Conditions of Sale
and Delivery.
Rhein Chemie Rheinau GmbH
Duesseldorfer Strasse 23-27
68219 Mannheim, Germany
Tel.: +49-621-8907-0
Fax: +49-621-8907-675
E-Mail:
[email protected]www.rheinchemie.com
Page Version: Revised: Printed on:
3 of 3 1/01. Apr 99 01-15-2015 01-15-2015
