Scribd
Upload
77 views

PSPICE Transient Simulation Plotting

This document provides instructions for performing a transient simulation and plotting results in PSpice. It demonstrates how to: 1) Place voltage and current markers to automatically plot simulation results. 2) Run a transient analysis simulation of a circuit with a sinusoidal input voltage and plot the output voltage. 3) Add additional traces to plot, such as the voltage across a capacitor. 4) Use interactive cursors to determine voltage and current values at specific points on the plotted traces. 5) Replace the sinusoid with a digital pulse input and plot the current through a resistor for a transient simulation with the new input.

Uploaded by

jae hak kim
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
77 views

PSPICE Transient Simulation Plotting

This document provides instructions for performing a transient simulation and plotting results in PSpice. It demonstrates how to: 1) Place voltage and current markers to automatically plot simulation results. 2) Run a transient analysis simulation of a circuit with a sinusoidal input voltage and plot the output voltage. 3) Add additional traces to plot, such as the voltage across a capacitor. 4) Use interactive cursors to determine voltage and current values at specific points on the plotted traces. 5) Replace the sinusoid with a digital pulse input and plot the current through a resistor for a transient simulation with the new input.

Uploaded by

jae hak kim
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

PSpice Transient Simulation & Plotting Your Results

I. Transient simulation with a Sinusoid

Start with the schematic shown below


Markers can be used to automatically plot simulation results after a simulation has run

1) Place Markers using the place marker icon (top toolbar) at Vin and Vo (as shown below).

Place Voltage Marker icon

(also find place current and


differential voltage marker icons)
Sets initial
condition on
capacitor

marker

II. Simulating

2) Create a new simulation profile: Top toolbar:


PSpice->New simulation Profile

3) Enter a Name in the New Simulation Pop-up


menu

4) Click on <Create> to close the window

5) In the Simulation Settings Window (shown)


a) Select Time Domain/Transient Analysis
b) Set the simulation run time (2m)
c) Set the minimum step size
d) Click <OK> to close the window and apply
settings

1
6) To run the simulation: select the run simulation icon (top toolbar)

Run simulation icon

Your Results will be Plotted in the Resulting Simulation Window

(Vo is hard to see because it is so small)

7) Adding a New Plot Window


a) From the Top toolbar of the SCHEMATIC-sim window select: Plot→Add Plot to Window
b) Select the V(Vo) icon at the bottom of the window
c) Hit ^x to copy
d) Click on the top plot
e) Hit ^v to paste

Click here and hit


^v to paste

Select, hit ^x to cut

2
III. Adding Additional Traces
After running a simulation you can display additional traces or functions performed on traces. We will plot (Vo-Vn)
(the voltage across the capacitor)

8) Adding Traces
a) From the Top toolbar of the SCHEMATIC-sim window select: Trace→Add Trace
b) Enter the Expression V(Vo)-V(Vn) as shown below
c) Click on <OK> to close the window

Voltages
and currents Functions
that can be that can be
plotted perfomed

3
IV. Using Cursors

It is possible to determine precise current and voltage values after running a simulation using interactive cursors.
There are two cursors: Y1 and Y2. Y1 is controlled with the left mouse button and Y2 with the right

9) Add cursors: Top toolbar select: Trace→Cursor→Display

10) Controlling Y1 (left mouse) cursor


a) Click on the little square of the V(Vo) trace icon with your left mouse (for this example V(Vo)).
This will affiliate the Y1 (left mouse cursor) with the trace V(Vo).

Little square

b) Click on the actual V(Vo) trace with your left mouse. You will see a crosshair at the location
(see below)
c) Keeping your left mouse button depressed drag the crosshair to a different location
d) At the bottom of the screen (X,Y) information for the Y1 cursor is displayed. Also find
information for Y2 and Y1 minus Y2. (see below)

Crosshair for
Y1 cursor

Data for Y1
and Y2
cursors

The Y2 (right mouse) cursor data can be displayed by repeating steps (16)-(18) that were used for the
Y1 cursor (left mouse) substituting the right mouse

4
V. Transient Simulation with a Digital Pulse

11) Return to your schematic window


12) Change the capacitor value to 1uF
13) Select the Vsin part and delete it using the <delete> key

There are two parts that can commonly be used for digital simulation: Vpwl and Vpulse (also Ipwl and Ipulse for
currents). Here we will use Vpwl.

PWL (PieceWise Linear) format


PWL describes a waveform that is linear in pieces (piecewise linear). It consists of successive pairs of
points (Ti, Vi) as shown below.
(T3, V3) (T4, V4)

(T1, V1) (T2, V2) (T5, V5)

14) Add and edit a Vpwl part:


a) Add a Vpwl part from the Library source (Bindkey p) to replace the Vsin part that was just deleted
b) Double Click on the Vpwl part
c) In the resulting window scroll to the right to expose part properties T1, T2,… and V1, V2 (see below)

d) Enter the following part properties.

Ti Vi
(T1, V1) 0 0
(T2, V2) .5m 0
(T3, V3) .501m 1
(T4, V4) 1m 1
(T5, V5) 1.001m 0

e) Click on <Apply>
f) Click on the close window x (top right) to close the window

5
VI. Plotting Currents

15) On your schematic add a current marker plotting the current through the resistor
a) Select the Add Current marker icon
b) Place the marker on the pin of the resistor (the very edge of the part)

Add Current
marker

16) Rerun the simulation (top toolbar run simulation icon) (See step (6)
of this tutorial)

VII. Working with Equations and Parameter Sweep


One can declare variables and create equations based on these variables. We will run three simulations using
three different capacitor values.

Declaring a variable

17) Declaring a variable:


a) Place the part Param from the Library Special on the schematic
b) Double click on the PARAMETER part
c) Select New Column (or New Row)
d) In the Add New Column window enter a name for your variable (here we are using val)
e) In the Add New Column window enter a default value for your parameter (here we are using 1)
f) In the Add New Column click <apply> to apply
g) In the Add New Column click on the X (top right
corner) to close the window
h) Click <apply> again in the first window
i) Click on the X (top right corner) to close the
window

6
Creating an Equation

18) Curley brackets are used to denote equations. Edit the Capacitor value to be: {val*1u}.

VIII. Performing a Parametric Nested Sweep

19) Performing a Parametric Nested Sweep


a) In the schematic window edit the simulation profile: Top toolbar→PSpice→Edit Simulation
Profile
b) Additionally select: Parametric Sweep
c) Select: Global parameter
d) Indicate the parameter to be swept: val
e) And the range for val
f) Click on <OK> to close the window

20) Rerun the simulation (top toolbar run simulation icon) (See step (6) of this tutorial)
21) In the resulting window select <OK> to plot all results

You might also like