Scribd
Upload
142 views

CNF Project

This document outlines a networking project for students to design, implement, and test a network connecting three new university buildings - the IT Center Building, Robert Sobukwe Building, and Steve Biko Memorial Building. Students must plan the network, allocate IP addresses, configure routers and switches, implement wireless connectivity and DHCP, demonstrate redundancy, and perform security and connectivity tests using Cisco Packet Tracer. The project assesses students' knowledge of networking fundamentals and requires them to apply best practices for network design, configuration, security, and testing.

Uploaded by

nganga
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
142 views

CNF Project

This document outlines a networking project for students to design, implement, and test a network connecting three new university buildings - the IT Center Building, Robert Sobukwe Building, and Steve Biko Memorial Building. Students must plan the network, allocate IP addresses, configure routers and switches, implement wireless connectivity and DHCP, demonstrate redundancy, and perform security and connectivity tests using Cisco Packet Tracer. The project assesses students' knowledge of networking fundamentals and requires them to apply best practices for network design, configuration, security, and testing.

Uploaded by

nganga
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

DEPARTMENT OF INFORMATION TECHNOLOGY

FACULTY OF INFORMATICS AND DESIGN

PROJECT SPECIFICATION NETWORK PLANNING, DESIGN,


CONFIGURATION and TESTING

DUE DATE
SUBJECT TOTAL MARKS

COMMUNICATION NETWORKS 22 August 2017 100


FOUNDATIONS 1 (CNF152S)
COURSE(S) ND: ICT (APPLICATIONS DEVELOPMENT)

EXAMINER (S) MRS C. MUSHONGA


MODERATOR (INTERNAL) MS T. NCUBUKEZI

INSTRUCTIONS TO STUDENTS
This project is about designing an appropriate network configuration. Use your expert
knowledge on network design to plan for the university network.
Use Cisco Packet tracer to implement the design
This project is to be done and submitted in pairs (2).
Submit your project files to your lecturer by email unless otherwise specified by your
lecturer.
[email protected]
[email protected]
[email protected]

1
Assignment format
Students must follow the generic requirements when writing and submitting this project
as follows:
Use standard Arial, font size 11.
table of contents, page numbers and a title page.
the page and are labelled.

mitted

Resource requirements

Assessment Sections Assessed


The following units are assessed in this assignment:

Introduction to networking Transmission media


Topologies and Ethernet standards OSI Model
Configurations and Protocol implementation IP addressing

Question Mark allocated Obtained Mark

Question 1 24
Question 2 55
Question 3 12
Question 4 9

2
Project scope
Plan the network to be deployed in three new buildings which are (IT Centre Building; Robert
Sobukwe Building; Steve Biko Memorial Building) on a new West Coast university campus. These
building should belongs to a separate Virtual Local Area Network (VLAN) as the way of improving
security.

Building Requirements
The IT Centre Building contains a dedicated computer room containing a single high end server
which provides services such as DHCP, Print services, Web to students and staff who may need
to gain access from the Internet as well as from within the universitys own network. The IT room
also has 5 desktop PCs for the IT staff.

The Robert Sobukwe Building contains the offices of 22 lecturers and 8 administrators who only
use medium power desktop computers located on fixed desks. The building also has a single
printer.

The Steve Biko Memorial Building contains two lecture rooms and a lounge/coffee shop. The
lecture rooms each have a desktop computer at the front for use by the lecturers as well as 20
desktops for students. However, some lecturers and students prefer to use their own laptop or
tablet computer. All the students use laptop or tablet computers to take notes.

An underground duct exists between IT Centre Building and Robert Sobukwe Building which are
130 metres apart. The Steve Biko Memorial Building is 80 metres from IT Centre Building but no
ducts exist.

Instructions
To avoid the overcrowding of the simulation environment, students may represent the maximum
Users per building with any few number of users. For instance, they may decide to have only two
users per building (i.e. by using 1st usable address and last usable address). However,
students are advised to configure more than two hosts per building.

Question 1 [24 Marks]


Analyze and design a network for the West Coast university campus. Provide a detailed
documentation of the network you have designed and rationale for the choices that you have
made.

3
a. Plan your network and document all the requirements per building. This would include
all the components of the network. (12)
b. Show a good IP addressing scheme for your LANs and WANs (12)

NB: With regards to all the routers, you have been asked to use your expertise in allocating
the IP address 192.168.1.0/30. All buildings will need to be networked to assure
connectivity. It is your choice whether to use Satellite / Wireless /or Cabled connections.
In this type of institution, you also need to consider Redundancy for the network.
Redundancy only needs to be applied to each building once.

Question 2 [55 Marks]


Implement your design. The implementation, including working demonstrations, should be done
within Cisco Packet Tracer. The implementation should have the following:

a. All buildings should be networked according to the scenario to ensure connectivity.


(12)
b. Include appropriate wireless connections necessary for each building. (9)
c. Network services like DHCP (Dynamic Host Configuration Protocol) should be
configured where necessary (12)
d. Include relevant device configurations, such as router configurations, and working
switch VLAN configurations (15)
e. You should also consider redundancy for the network. Note that redundancy can only
be applied to each building once. Assume scalability within your design and
implementation to account for 10% annual growth. (7)

Question 3 (12)
This section focuses on router security and connectivity testing.
a. Perform a ping test of devices across the three buildings to prove that there is
connectivity between devices. Provide screenshots. (12)

Question 4 (9)
This section focuses on security and authentication.
4.1 As the network planner, set distinct passwords on all the main routers in each
building. Show all the steps (with screenshots) of how you carried out this task. (6)
4.2 Prove that the password you implemented on the routers in Question 4.1 is working
on all routers. Provide screenshots. (3)

4
THE END

You might also like