Scribd
Upload
111 views

Fatigue Failure

Fatigue is the degradation of materials under cyclic loading that can lead to failure. It is caused by repeated stress and affects components that experience movement, like aircraft wings. Three factors are necessary for fatigue failure: maximum stress, stress variation, and number of cycles. The stress-life and strain-life approaches are used to analyze high and low cycle fatigue respectively.

Uploaded by

Hafiezul Hassan
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
111 views

Fatigue Failure

Fatigue is the degradation of materials under cyclic loading that can lead to failure. It is caused by repeated stress and affects components that experience movement, like aircraft wings. Three factors are necessary for fatigue failure: maximum stress, stress variation, and number of cycles. The stress-life and strain-life approaches are used to analyze high and low cycle fatigue respectively.

Uploaded by

Hafiezul Hassan
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 5

Fatigue in metals:

Fatigue is a degradation of mechanical properties leading to failure of a material or a


component under cyclic loading. (This definition excludes the so-called phenomenon
of static fatigue, which is sometimes used to describe stress corrosion cracking in
glasses and ceramics in the presence of moisture).
In general, fatigue is a problem that affects any structural component or part that
moves. Aircraft (principally the wings) in the air, nuclear reactors and turbines under
cyclic temperature conditions (i.e., cyclic thermal stresses) are examples in which the
fatigue behavior of a material assumes a singular importance. It is estimated that 90%
of service failures of metallic components that undergo movement of one form or
another can be attributed to fatigue.
Often, a fatigue fracture surface will show some easily identifiable macroscopic
features, such as beach markings.
The main features of this kind of failure are:
a)a fatigue crack initiation site, generally at
the surface;
b) a fatigue crack propagation region showing
beach markings;
c) a fast-fracture region where the crack length
exceeds a critical length.
Typically, the failure under cyclic loading
occurs at much lower stress levels than the
strength under monotonic loading with little
or no warning (with catastrophic results).

Three basic factors are necessary to cause


fatigue failure:
- max. tensile stress of sufficiently high value;
- large enough variation or fluctuation in the applied stress;
- sufficiently large number of cycles of the applied stress.
In addition: stress concentration, corrosion, temperature, metallurgical structure,
residual stresses, and other variable tend to alter the conditions for fatigue.
The study of cyclic behavior of materials can divided into three classes:
- Stress-life approach: It is useful when stresses and strains are mostly elastic. The
main drawback of this approach is that we are unable to distinguish between the
initiation and propagation phases of fatigue life.
- Strain-life approach: The strain-life approach is useful when there is a significant
amount of plastic strain.
- Fracture mechanics approach: The cyclic stress intensity factor is used as the
crack driver to estimate the life for propagating a crack from an initial size to larger
size or to the critical size corresponding to failure.

Stress cycles:

1
cyclic stress range = max min , cyclic stress amplitude a = /2,
mean stress m = (max + min)/2, stress ratio R = min /max,
Amplitude Ratio, A= a / m= (1-R)/(1+R)

Fatigue regimes:
Fatigue regime

Low cyclic fatigue, LCF (Nf < 103)


3
High cyclic fatigue, HCF (Nf >10 ) (Low number of cycles with high level
(High number of cycles with may be of stress mainly of thermal origin as in
low level of stress). stesm turbine, nuclear pressure vessel,
(stress life approach/ The S-N curve ) )
(strain life approach/ The S-N curve )

The S-N curve ( or the stress life approach): is used for HCF. This approach
attempts to keep local stresses so low that the crack initiation stage never begins, i.e,
stress and strain everywhere remain in the elastic region and no local yielding occurs
to initiate a crack.

2
A- for N< 106 a fatigue strength Sf can be defined at any Nf.
- endurance limit Se, is used only for infinite life strength, (N>106).
For steel S e 0.5 ult . (ult.<200Kpsi)
S e 100 Kpsi (ult. 200Kpsi)
B- For Al: S f 510 0.4 ult .
8

Sm = Fatigue strength at N=103


= 0.9ult (bending and torsion)
= 0,75ult (axial loading)

For ferrous metals:


Sf = Sm at N=N1 and Sf = Se at N=N2 = 106
But log Sf = log a + b log N, when you subt. the boundary conditions and solve
for a&b you will get that:
1 S
b log m when; Z = log N1-log N2= - 3 So: log a = log Sm 3b
z Se

For non-ferrous metals:

3
Sf = Sm at N=N1=103 and Sf = Sf at N=N2
1 S
b log m when; Z = log N1-log N2
z S
f

Example:Aluminum bar is subjected to a torsion a torsion load. What is the fatigue


strength at N= 2E7 cycles, if ult= 45kpsi and Sf 5E8 = 11.063.

Solution: Sm = Fatigue strength at N=103


= 0.9ult (bending and torsion) = 40,5kpsi
Z = log N1-log N2 = log 103- log 5E8 = - 5.699
S
b
1
log m = 1 log 40.5 = - 0.0989
z S 5.699 11 .063
f
log a = log Sm 3b, so: a = 80193

Sf = 80193(2E7)- 0.0989 = 15.209kpsi


In LCF fatigue life is treated in terms of strain versus number of cycles to failure.
For low-cycle fatigue, crack initiation is rapid and crack propagation accounts for
most of the life, whereas for high-cycle fatigue most of the life is spent in crack
initiation. This leads to the conclusion that under constant strain-amplitude cycling, a
ductile material is desirable for low-cycle fatigue and a high-strength material is
desirable for high-cycle fatigue. High-strength materials generally have low ductility
(low value of and ductile materials generally have low strength.

Effect of Mean Stress on Fatigue Life:

The mean stress m can have an important


effect on the fatigue strength of a material.
For a given stress amplitude a, as the
mean stress increases, the fatigue life decreases.

Various empirical expressions have


been proposed which take into
account the effect of mean stress on
fatigue life. Some of these are the
following:
- Goodmans relationship:

a = 0[1 m/ult].

- Gerbers relationship:

a = 0[1 (m/ult)2].

4
- Soderbergs relationship: a = 0(1 m/yp).
In all these relationships, 0 is the fatigue strength in terms of stress amplitude when
m = 0.

You might also like