Scribd
Upload
568 views1 page

Corbel Calculation

This document provides design calculations for reinforcing a corbel that will support a shear force of 1500 kN and tension force of 300 kN. The corbel is 500 mm wide, 325 mm deep with a 75 mm eccentricity of the load. Reinforcement requirements are calculated for flexure, tension, and shear. A total area of 3696 mm^2 of D28 reinforcement is required to resist all forces based on the given concrete and steel properties. Stirrup requirements are also calculated.

Uploaded by

QuangKhải
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
568 views1 page

Corbel Calculation

This document provides design calculations for reinforcing a corbel that will support a shear force of 1500 kN and tension force of 300 kN. The corbel is 500 mm wide, 325 mm deep with a 75 mm eccentricity of the load. Reinforcement requirements are calculated for flexure, tension, and shear. A total area of 3696 mm^2 of D28 reinforcement is required to resist all forces based on the given concrete and steel properties. Stirrup requirements are also calculated.

Uploaded by

QuangKhải
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

CORBEL FOR REPLACING THE BEARINGS (ACI 318M-08 )

Design information
Design shear V 1500 kN
Design tension force (min = 20%V) N 300 kN
Grade of concrete f'c 30 Mpa
Grade of steel fy 395 Mpa
Width of corbel b 500 mm
Total depth of corbel h 325 mm
Eccentricity of load V av 75 mm
Cover to main reinforcement co 50 mm
Assume Dia of Main reinforcement db 25 mm
Effective Depth d = h - co - db/2 262.5
Strength reduction factor (11.8.3.1) 0.75
Check av/d<1 OK
Flexure and Tension (11.8.3)
Design moment Mu = V*av+N*(h-d) 131.25 kN.m
Assume area of steel for flexure Af 2683 mm2
Check design moment and design capacity
Depth of equivalent rectangle stress block a=Af*fy/(0.85*fc*b) 83.1 mm
Flexure capacity of section *Mn=*Af*fy*(d-a/2) 175.6 kN.m
Check OK
Area of steel require for direct section tensile An=N/(*fy) 1013 mm2
Total area of steel required As = Af+An 3696 mm2
Design for shear (11.8.3.2 and 11.6)
Coefficient of friction m 1.4
Area of shear friction reinforcement required Afv = V/(*m*fy) 3617 mm2
Check OK
Design reinforcement (11.8.3.5, 11.8.3.4, 11.8.5)
Area of reinforcement shall be taken larger than (1) or (2)
(1) Af+An 3696 mm2
(2) 2*Afv/3+An 3424 mm2
Therefore , area of main Rein required Asc 3696 mm2
Choose the reinforcement : 6 Bars D28 Area : 3696 mm2
Minimum Area of Main Rein Asc = 0.04*fc*b*d/fy 399 mm2
Check OK
Area of stirrups to main reinforcement Ah = 0.5*(Asc-An) 1341.7 mm2

You might also like