Operating Instructions SONO-

VIEW

I:\publik\TECH_MAN\SONO-View\Englisch\Manual_SONO-View.docx
 Manual SONO-VIEW 2015-02-13

SONO-VIEW

Stand-alone display for the reliable control and configuration of processes using SONO moisture
probes. A total of up to 4 SONO probes can be monitored and the respective measurement values
presented at the LCD via a serial interface.

Thank you very much for your decision to purchase this IMKO product.

Should you have any questions in respect to this product, please contact our local
distribution partner or IMKO directly.

IMKO Micromodultechnik GmbH

Im Stck 2

D-76275 Ettlingen

Germany

Phone: +49-7243-5921-0

Fax: +49-7243-90856

E-mail: [email protected]

Internet: http://www.imko.de

Page 2
2015-02-13 Manual SONO-VIEW

Table of Content

1 General Notices.................................................................................................................................. 5

1.1 Intended Use .......................................................................................................................... 5

2 Control Elements / Connections ................................................................................................. 6

2.1 Control Elements .................................................................................................................... 6

2.2 Connections ............................................................................................................................. 6

3 Initial Commissioning ..................................................................................................................... 7

3.1 Safety Instructions .................................................................................................................. 7

3.2 Checking the Package Content for Completeness ........................................................... 7

3.3 Connection............................................................................................................................... 7

3.3.1 Exemplary Connections.................................................................................................. 8

4 Operation ......................................................................................................................................... 9

4.1 Initial and New Installation ................................................................................................... 9

4.2 Measurement Value Display ............................................................................................... 10

4.4 Settings .................................................................................................................................. 12

4.4.1 New Set-Up ................................................................................................................. 12

4.4.2 Language ....................................................................................................................... 12

4.4.3 Display Contrast ........................................................................................................... 13

4.4.4 Information about your SONO-VIEW........................................................................ 13

4.4.5 Info ................................................................................................................................. 13

4.4.6 USB-IMP-Bridge .......................................................................................................... 13

4.5 Probe Settings ...................................................................................................................... 14

4.5.1 Probe Info ..................................................................................................................... 15

4.5.2 Material Calibration ...................................................................................................... 15

4.5.3 Offset Balancing ........................................................................................................... 15

4.5.4 Averaging Mode ........................................................................................................... 15

4.5.5 Averaging Parameters .................................................................................................. 16

4.5.6 Basic Balancing ............................................................................................................ 18

5 Technical Data ............................................................................................................................. 18

Seite 3
 Manual SONO-VIEW 2015-02-13

Page 4
2015-02-13 Manual SONO-VIEW

1 General Notices
Please carefully read and get acquainted with these operating instructions.

Should any queries arise, please contact our service department under the contact data
depicted above. Do not, under no circumstances, attempt to open or repair the device
yourself. In the event of any warranty claims, please refer these to the retailer you purchased
the device.

The device is subject to technical and optical change within the scope of product
improvement.

1.1 Intended Use

This device was developed to serve as a display and configuration device for various IMKO
probes. Only the respectively intended probes may be connected to the device. The
connection of any probe which is not intended for the device, can lead to damage or the
destruction of this device and/or the connected probe.

Seite 5
 Manual SONO-VIEW 2015-02-13

2 Control Elements / Connections

2.1 Control Elements

2.2 Connections

USB (Type-Mini B) -Supply Voltage

-USB-IMP-Bridge -Bus-Interface
-Firmware Update

Page 6
2015-02-13 Manual SONO-VIEW

3 Initial Commissioning

3.1 Safety Instructions

Attention: It is strictly necessary to read the General Notices contained under Item I at the
beginning of the operating instructions. Any not intended use of the device can lead to
damage to this device.

3.2 Checking the Package Content for Completeness

SONO-VIEW
Terminal Block
USB Cable (Type A Mini B)

3.3 Connection
For operation, the SONO-VIEW requires a supply voltage of 7...24V (approx. 80..30mA). A
joint ground wire together with the probes is not required. For the connection with the
probes, it is sufficient to merely connect the two bus lines RTand COM.

0V +7..24V (RT) IMP-Bus (COM) IMP-Bus

Notice: The SONO-VIEW is suited for the display and configuration of up to four
probes. Should more than four probes be connected, an error message will
be generated and the device can not operate correctly.

Seite 7
 Manual SONO-VIEW 2015-02-13
3.3.1 Exemplary Connections

Example 1: Connection of the SONO-VIEW with two SONO probes and one joint voltage
supply source.

Example 2: Connection of the SONO-VIEW with 2 SONO-probes merely via IMP-bus.

SONO-VIEW and the probes dispose of their voltage supply. This may be
useful, if the distance between the measuring equipment and the display
device is considerable.

Page 8
2015-02-13 Manual SONO-VIEW

4 Operation

4.1 Initial and New Installation

At the initial connection to your probe-network, it is necessary to set the same up,
respectively follow an installation procedure at the SONO-VIEW.
For this purpose, the device will scan the IMB bus for
connected probes.
Initiate the installation with the button .

After an instant, the serial numbers of all connected

probes are listed in the display.

In order to maintain the clarity within the

administration of the probes, the SONO-VIEW operates
on the basis of assigned probe numbers (1...4).
These must be allocated to the detected serial numbers
in the next step. For each probe number, select a serial
number using the / buttons and subsequently
acknowledge the same with the button .

Repeat this procedure until all serial numbers have

been allocated a probe number.

Seite 9
 Manual SONO-VIEW 2015-02-13
After completion of the above steps, all probe numbers
will be presented once more together with the
respectively allocated serial numbers in ascending
order.
Complete the installation process with the button .

Notice: The SONO-VIEW is suited for the display and configuration of up to four
probes. Should more than four probes be connected, an error message will
be generated and the device will not be able to operate properly.

After completion of the installation process, the SONO-VIEW will re-start, verify the
connected probes, and will immediately commence to call up the measurement values.

4.2 Measurement Value Display

The SONO-VIEW immediately commences to call up and display the measurement values
after start-up. This is performed in a 500 ms cycle. Depending on how many probes are
connected, from one to four, the following displays will be presented.

The moisture value in percent and the respective probe number is always presented. If two
or three probes are connected, the temperature measured by the probe is additionally also
presented. In the event that only one probe is connected, the calibrated radar run-time is also
presented.

If more than one probe is connected to the SONO-VIEW, there is an option to change the
display. For this purpose, actuate the buttons / . Subsequently, all connected individual
probes are presented consecutively. For the purpose of allocation, the probe number is

Page 10
2015-02-13 Manual SONO-VIEW
always also presented in the upper section. If this form of display is maintained for a longer
period, the same will be assumed as Standard. In this case, the SONO-VIEW will present
this set measurement display form after a re-start.

Seite 11
 Manual SONO-VIEW 2015-02-13

4.4 Settings
Actuate the button while the measurement display is active and you will reach the setup
menu. Here, you are enabled to perform various settings and call up information regarding
the SONO-VIEW.

The setup menu features the following structure:

Setting Description
New Setup Enables a new detection of connected probes

Language Setting of the language

Display Contrast Setting of the display contrast

About SONO- Serial number and further information regarding your SONO-VIEW
VIEW
Info Support information

USB-IMP-Bridge Enables the comfortable configuration of your probes via PC

Set the desired setting using the buttons / . By actuating the button , you can
subsequently enter the selected setting. Actuate the button again in order to exit the setup
menu.

4.4.1 New Set-Up

See Section 4.1 Initial and New Installation

4.4.2 Language
The selection of the language is performed with the buttons / . By actuating the button
, the selected language is set as the standard language. To exit the menu item Language,
actuate the button .

Page 12
2015-02-13 Manual SONO-VIEW
4.4.3 Display Contrast
A bar containing a grey colour gradation will appear.

Set the contrast using the buttons / in a manner

that enables you to recognise all grades. Store the set
value with the button . To exit the menu item
Display Contrast, actuate the button .

4.4.4 Information about your SONO-VIEW

The device will present the serial number, the HW-
version, the IBT version, as well as the firmware
version. By actuating the button , the device will
present further status information such as the currently
connected probes and system voltage values. To exit
the menu item About SONO-VIEW, actuate the
button .

4.4.5 Info
Contains links to the IMKO homepage and the E-mail address to request support.

4.4.6 USB-IMP-Bridge
As soon as this menu item is called up, the SONO-VIEW changes into a transparent data
mode. All data packets will be now redirected from the USB interface directly on to the IMP-
bus and vice versa. This enables a comfortable configuration of the probes via a connected
PC without the necessity of additional hardware. For this purpose, please download the free
software SonoConfigas well as the respective operating instructions available on the
IMKO-homepage.

Connect the SONO-VIEW to the PC using the provided USB cable. The SONO-VIEW will
connect with the PC as a virtual serial interface (COM-Port). The respectively required driver
is usually automatically installed by all currently used Windows versions. Should the driver

Seite 13
 Manual SONO-VIEW 2015-02-13
not be automatically installed, please download the driver under:
http://www.ftdichip.com/Drivers/VCP.htm.

Notice: As long as the SONO-VIEW is in the USB-IMP-Bridge modus, no

measurement values are queried by the probe. The probes however
continue to measure and issue the measurement value at the analogue
output.

Actuate the button in order to exit the menu item USB-IMP-Bridge.

4.5 Probe Settings

The SONO-VIEW offers the option to comprehensively configure the connected probes even
without PC. Settings such as offset displacements or the selection of a material-specific
calibration can be simply adjusted with the buttons / .

The menu Probe Settings respectively offers the following options:

Setting Description
Probe Info Presents information regarding the connected probe

Material Calibr. Selection of a material-specific calibration

Offset balancing Displacement of the measurement value

Average Mode Setting of the method of averaging

Average Paramet Setting of the parameters of the set averaging method

Basic balancing Zero Value calibration of the probe in ambient air

To reach the probe settings, select the individual probe display mode for the probe intended
for configuration in the measuring display using the / buttons (also see Item 4.2). By
actuating the button , the probe setting of the currently used probe is called up.

Notice: It is only possible to configure one probe at a time. Should several probes
require to be adjusted, the procedure must be respectively repeated for
these other probes.

Attention: Ensure that the correct probe is set before commencing with adjusting the
parameters.

Attention: The SONO-VIEW offers the option to access the measuring parameters of the
probe. Before adjusting any parameters, please inform yourself precisely in
regard to the function of the same in the respective probe manual. Any
performed changes may affect the measurement value, the accuracy, and the
measuring rate.

Page 14
2015-02-13 Manual SONO-VIEW
4.5.1 Probe Info
If this menu item is selected, various information of the probe is called up and displayed.

You can exit the menu item Probe Info with the
button .

4.5.2 Material Calibration

The menu item Material Calibrationenables to adjust a material-specific calibration stored
in the probe. This enables to significantly increase the accuracy of the measurement. There
are up to 15 material-specific calibrations deposited in the firmware of a SONO probe. These
are presented here and can be selected with the buttons / . The character 1 set in
front of a calibration hereby points out the current standard calibration. Store the selected
calibration as standard in the probe using the button . The set calibration will subsequently
be stored in the non-volatile memory of the probe. The menu item Material calibration is
exited by actuating the button .

4.5.3 Offset Balancing

In order to compensate measurement errors e.g. due to density deviations in the material or
due to the installation conditions, there is an option to perform a linear displacement of the
measurement value. This is the purpose of this menu item. It is possible to displace the
measurement value between -10 and +10 percent points. The set displacement is stored in the
probe and will subsequently also affect the analogue output. The setting is maintained in a
traceable manner.

Adjust the offset to the desired value using the buttons

/ . Subsequently store the set value in the probe
with the button . You can exit this menu item with the
button .

4.5.4 Averaging Mode

This menu item enables the activation, respectively the changing of a measurement value
establishment in the probe. The IMKO moisture probe respectively offers the following
options:

Mode CS: (cyclic-successive) Without averaging function intended for very short measuring
processes in a range limited to seconds (e.g. 520 seconds) at which up to 100 measurements

Seite 15
 Manual SONO-VIEW 2015-02-13
are performed internally per second at a cycle time of 250 milliseconds at the analogue
output. The operating mode CS also serves for the collection of raw values without
averaging and filter functions.
Mode CA: (cyclic average filter) Standard averaging for relatively fast but continuous
measurement processes with filtering and an accuracy of up to 0.1%.
Mode CF: (cyclic floating average with filter) Floating averaging for very slow and
continuous measurement processes with filtering and an accuracy of up to 0.1%.
This is suited for applications such as within a fluid bed dryer, on the conveyor belt, etc.
Mode CK: (cyclic with Kalman filter) suitable for complex application
Mode CC: (cyclic cumulated) with automatic summation of the moisture-quantity
measurements in one batch operation.

Notice: Please respectively also read the further information contained in your probe
operator manual.

Set the desired Average Mode with the buttons /

and subsequently set the set mode as standard with
the button . Once this is performed, the setting is
stored in the probe. You can exit the menu item
Average Mode with the button .

4.5.5 Averaging Parameters

Depending on the set Averaging Mode, there are various Average Parametersavailable
for control purposes.

Averaging Mode Available Parameters

Average Time
Filter Upper Limit Offset
CA Cyclic Average Filter Lower Limit Offset
Upper Limit Keep Time
Lower Limit Keep Time
Kalman with Boost
Average Time
Filter Upper Limit Offset
Filter Lower Limit Offset
Upper Limit Keep Time
Lower Limit Keep Time
CK Cyclic Kalman
Q-Parameter
R-Parameter
K-Parameter
Moisture Threshold
Boost
Offset

Page 16
2015-02-13 Manual SONO-VIEW

Average Time
Filter Upper Limit Offset
CF - Cyclic Floating Filter Lower Limit Offset
Upper Limit Keep Time
Lower Limit Keep Time
Moisture Threshold
CC - Cyclic Cumulate
No Material Delay

Notice: Please respectively also read the further information contained in your
probe operator manual.

Attention: Before adjusting a parameter, please precisely inform yourself in regard to the
function of the same. Any performed change may affect the measurement
value, the accuracy, and the measuring rate.

The parameters are dynamically enabled with the set Average Parameter.

The buttons / serve for the navigation

between the individual parameters. The
current value of the selected parameter is
presented in the lower left section of the
display. To change the value, actuate the
button .

The value will now appear enlarged in the

display. Adjust the value with the buttons
/ and subsequently assume the same
with the button . You also have the option
to exit the entry with the button without
performing any change to the value. Repeat
this procedure for all parameters intended
for adjustment.

As soon as you have performed all

adjustments as desired, select the item
Save and acknowledge the same with the
button . Now, the parameters are written
back into the probe and are immediately
effective.
You can exit the menu item Average
Parameters with the button without
saving the same. Hereby, all performed
changes are deleted!

Seite 17
 Manual SONO-VIEW 2015-02-13
4.5.6 Basic Balancing
At the exchange of a sensor head, due to deviating cable lengths, it may be necessary to
perform a basic balancing in air. Hereby, the moisture measurement value of the probe is re-
aligned to the correct Zero Value.

Actuate the button in order to start the basic

balancing. The balancing will be performed
subsequently.

Attention: In order to exclude the occurrence of a faulty air calibration, the sensor must
be dry and free of any material during basic balancing.

The notice Please wait will be generated in the

display. The procedure lasts approximately 30 seconds.

5 Technical Data

Power Supply +7 .. 24V DC / 0.7W

Operating 0 .. 50C
Temperature
Dimensions 145mm x 75mm x 34 mm
Weight 153g
Mounting Cap Rail (optional)
Interfaces IMP-Bus (RT / COM)
USB Mini-B (galvanically isolated)

Page 18
2015-02-13 Manual SONO-VIEW
Notes:

Seite 19
 Manual SONO-VIEW 2015-02-13
Notes:

Page 20
 Precise Moisture Measurement

in hydrology, forestry, agriculture, environmental and earth science,

civil engineering, as well as individual applications!

www.imko.de