NXP Semiconductor

Getting started with the LPCOpen

Ethernet Examples (lwip_tcpecho and
webserver)

By: Technical Information Center

About this document
This document will explain how to build and run the LPCOpen Ethernet example projects, it also explains
the needed board and PC connections and configurations.

The steps described in the document were done using the LPC1769 MCU like the one in the LPCXpresso
board for LPC1769 with CMSIS DAP probe, but the same principles are applicable to any LPC MCU.

Software versions
The steps described in this document are valid for the following versions of the software tools:

o LPCXpresso v8.1.4
o LPCOpen v2.xx

Boards
o LPCXpresso board for LPC1769 with CMSIS DAP probe
o EA LPCXpresso BaseBoard
o LPC-Link2

Contents
1. Overview and concepts .............................................................................................................................................3
1.1 LPCOpen .......................................................................................................................................................3
1.1.1 Core driver library ........................................................................................................................................3
1.1.2 Middleware ..................................................................................................................................................3
1.1.3 Examples ......................................................................................................................................................3
1.1.4 LPCOpen with an RTOS ................................................................................................................................3
2. Running the lwip_tcpecho and webserver demo applications ..................................................................................4
2.1 Downloading a LPCOpen package .......................................................................................................................4
2.3 Setting up the hardware......................................................................................................................................6
2.3.1 LPCXpresso board for LPC1769 with CMSIS DAP probe ...............................................................................6
2.3.2 EA LPCXpresso BaseBoard............................................................................................................................7
2.2 Importing the LPCOpen examples .......................................................................................................................9
2.4 Building the demo applications .........................................................................................................................12
2.5 Running the demo applications.........................................................................................................................15
2.5.1 lwip_tcpecho_sa demo ..............................................................................................................................15
2.5.2 webserver demo ........................................................................................................................................21
Appendix A - References..............................................................................................................................................26
Getting started with the LPCOpen Ethernet Examples
2 NXP Semiconductor
1. Overview and concepts

1.1 LPCOpen
LPCOpen is an extensive collection of free software libraries (drivers and middleware) and example
programs that enable developers to create multifunctional products based on LPC microcontrollers.
Access to LPCOpen is free to all LPC developers.

1.1.1 Core driver library

The core driver library contains common chip-specific drivers. It is divided into two layers: a chip driver
layer containing drivers optimized for a specific device or family, and a board layer containing board-
specific functions and low-level setup code.

1.1.2 Middleware
LPCOpen includes access to key middleware elements:

o SEGGER emWin graphics object library

o SWIM graphics library
o LWIP open-source networking stack - source code and examples
o USB libraries: USBD device library for all LPC devices and LPCUSBLib open-source USB host stack -
both use the USB ROM APIs or a Flash-based library

1.1.3 Examples
LPCOpen includes an extensive set of examples designed to illustrate how to use core driver library
functions and middleware. Examples demonstrate use of:

o Peripherals such as I2C, UART, SPI, and GPIO

o USB host and device
o Ethernet use with an IP stack (LWIP)
o emWIN and SWIM graphics libraries

1.1.4 LPCOpen with an RTOS

LPCOpen libraries are RTOS agnostic and can be used with a simple control loop. Examples are also
included in each software download package for use with FreeRTOS.

Getting started with the LPCOpen Ethernet Examples

3 NXP Semiconductor
2. Running the lwip_tcpecho and webserver demo applications

2.1 Downloading a LPCOpen package

- The LPCOpen packages can be found on the LPCXpresso installation folder, just make sure the
package to be used is the latest one available:

C:\nxp\LPCXpresso_8.1.4_606\lpcxpresso\Examples\LPCOpen

Getting started with the LPCOpen Ethernet Examples

4 NXP Semiconductor
 - In case it is not the latest package available go to the link http://www.nxp.com/lpcopen and select
the corresponding family of microcontrollers, for this example we chose the LPC1700 series:

- On the next page you will find the latest available LPCOpen software package downloads along
with older versions of the packages. Look for your board/device and click on the software
download link, for this example we chose the package for the LPCXpresso IDE but there is also a
package for the IAR and Keil IDEs:

Getting started with the LPCOpen Ethernet Examples

5 NXP Semiconductor
2.3 Setting up the hardware

Based on the readme information on the examples, the LPCXpresso LPC1769 board needs to be connected
with base board in order to use the RS232/UART and Ethernet ports. These are the connections and
configurations needed for the boards to work correctly.

2.3.1 LPCXpresso board for LPC1769 with CMSIS DAP probe

- There is a known issue with the LPCXpresso1769/CD board rev D (rev D1 boards are not affected).
Debugging works when the LPCXpresso1769/CD board is standalone but stops working when
mounted on a base board, it also causes that a "CRP DISABLD" USB drive appears on the PC instead
of the debug interface. This happens because the debug MCU (LPC11U35) will start-up in ISP mode
if an external reset signal is low during power-up. This is a typical situation if there is a reset
generator on the base board. So the workaround is to remove R57 on the LPCXpresso1769/CD
board. This will disconnect the ISP enable signal on the LPC11U35 from the external reset signal.

- Since the LPC1769 board will be powered by the baseboard the LPC-Link2 board will be used to
program and debug the demo applications. In order to use an external debugger to program the
LPC1769 MCU, the JP3 connector needs to be shorted to disable the CMSIS-DAP interface and
allow an external debugger to be connected.

Getting started with the LPCOpen Ethernet Examples

6 NXP Semiconductor
2.3.2 EA LPCXpresso BaseBoard

- The main power source will be used to power the system and will also be used as USB-to-UART
interface:

- The LPC1769 UART can be connected to one of three different peripherals in the EA LPCXpresso
BaseBoard, for this example we will use the USB-to-UART Bridge (U22) which is the default mode,
all the three jumpers in J7 need to be inserted:

Getting started with the LPCOpen Ethernet Examples

7 NXP Semiconductor
 - Remove the J54 jumpers, if these are not removed these cause the board to be always on reset.
This happens when using a terminal application, such as Tera Term, that is connected to the COM
port associated with the board and at the same time have the J54 jumpers inserted, the terminal
application might be the cause of this problem. If the terminal application is pulling DTR low the
board will be reset and if it pulls RTS low it will control the bootload enable functionality.

Getting started with the LPCOpen Ethernet Examples

8 NXP Semiconductor
2.2 Importing the LPCOpen examples

- Open LPCXpresso, create a new workspace and click on OK:

- On the Quick Start panel click on Import project(s):

- The Import project(s) wizard will open. There are two ways to import projects, import projects
contained in archives or unpacked projects, for this example chose the Project archive (zip) option
and click on Browse:

Getting started with the LPCOpen Ethernet Examples

9 NXP Semiconductor
 - Search for the downloaded *.zip file or locate the package included on the LPCXpresso
installation, select it and click on Open:

Getting started with the LPCOpen Ethernet Examples

10 NXP Semiconductor
 - Click on Finish:

Getting started with the LPCOpen Ethernet Examples

11 NXP Semiconductor
2.4 Building the demo applications

- After importing the projects to the workspace these can be closed to avoid having all of them
opened in the workspace. Then we can open only the lwip_tcpecho and webserver demos. Right
click on the projects and click on Open:

- A pop-up window will appear asking if the referenced projects should also be opened, click on
Yes, you should see the projects opened along with the M4 chip and board libraries:

Getting started with the LPCOpen Ethernet Examples

12 NXP Semiconductor
 - The next step is to build the projects, select the project, go to the Quick start panel and click on
Build lwip_tcpecho_sa [Debug] and Build webserver [Debug] respectively:

Getting started with the LPCOpen Ethernet Examples

13 NXP Semiconductor
 - The corresponding chip and board libraries will be built and the files lwip_tcpecho_sa.afx and
webserver.afx will be generated:

Getting started with the LPCOpen Ethernet Examples

14 NXP Semiconductor
2.5 Running the demo applications

Both of the demos require the board and laptop to be connected to a router since the board will acquire
an IP address via DHCP.

2.5.1 lwip_tcpecho_sa demo

- Select the project and go to menu Run > Debug Configurations:

Getting started with the LPCOpen Ethernet Examples

15 NXP Semiconductor
 - The Debug Configurations window will open, double click on the C/C++ (NXP Semiconductors)
MCU Applications option to create a new connection and program the MCU trough the LPC-
Link2 debug probe and click on Debug:

Getting started with the LPCOpen Ethernet Examples

16 NXP Semiconductor
 - A new window will show up and it will display the connected emulators, select the LPC-LINK2
CMSIS-DAP emulator and click on OK:

- After this a new message will show up, indicating that 2 SWD devices were found, select the
Cortex-M4 device which is the one used by the example:

Getting started with the LPCOpen Ethernet Examples

17 NXP Semiconductor
 - You should now be able to debug the program and step through the code:

Getting started with the LPCOpen Ethernet Examples

18 NXP Semiconductor
 - Now open an hyperterminal, in this care Tera Term, and connect with the USB serial port and
reset the board:

- You should see the following information printed on the hyperterminal:

Getting started with the LPCOpen Ethernet Examples

19 NXP Semiconductor
 - Finally after the board has acquired an IP address via DHCP, you can you can ping the board at it's
IP address:

Getting started with the LPCOpen Ethernet Examples

20 NXP Semiconductor
2.5.2 webserver demo

- Select the project and go to menu Run > Debug Configurations:

Getting started with the LPCOpen Ethernet Examples

21 NXP Semiconductor
 - The Debug Configurations window will open, double click on the C/C++ (NXP Semiconductors)
MCU Applications option to create a new connection and program the MCU trough the LPC-
Link2 debug probe and click on Debug:

- A new window will show up and it will display the connected emulators, select the LPC-LINK2
CMSIS-DAP emulator and click on OK:

Getting started with the LPCOpen Ethernet Examples

22 NXP Semiconductor
 - After this a new message will show up, indicating that 2 SWD devices were found, select the
Cortex-M4 device which is the one used by the example:

- You should now be able to debug the program and step through the code:

Getting started with the LPCOpen Ethernet Examples

23 NXP Semiconductor
 - Now open an hyperterminal, in this care Tera Term, and connect with the USB serial port and
reset the board:

- You should see the following information printed on the hyperterminal:

Getting started with the LPCOpen Ethernet Examples

24 NXP Semiconductor
 - Finally after the board has acquired an IP address via DHCP, you can now access the HTTP Server
by using a web browser from the host PC:

Getting started with the LPCOpen Ethernet Examples

25 NXP Semiconductor
Appendix A - References

- LPCOpen webpage:
http://www.nxp.com/lpcopen

- LPCXpresso webpage:
http://www.nxp.com/lpcxpresso

- LPCXpresso board for LPC1769 with CMSIS DAP probe:

http://www.nxp.com/products/software-and-tools/software-development-tools/software-
tools/lpc-microcontroller-utilities/lpcxpresso-board-for-lpc1769-with-cmsis-dap-probe:OM13085

- EA LPCXpresso BaseBoard:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/lpc-cortex-m-
mcus/lpc-cortex-m0-plus-m0/lpc800-low-cost-cortex-m0-plus/ea-lpcxpresso-baseboard:OM11083

- LPC-Link2:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/lpc-cortex-m-
mcus/lpc-cortex-m0-plus-m0/lpc800-low-cost-cortex-m0-plus/ea-lpcxpresso-baseboard:OM11083

- Product Note LPCXpresso1769/CD rev D:

https://www.embeddedartists.com/sites/default/files/support/xpr/LPCXpresso1769_CD_revD_Prod
uctNote.pdf

Getting started with the LPCOpen Ethernet Examples

26 NXP Semiconductor