TIA/EIA-568-B

From Wikipedia, the free encyclopedia

Jump to: navigation, search

TIA/EIA-568-B is a set of three telecommunications standards from the Telecommunications

Industry Association, a 1988 offshoot of the EIA. The standards address commercial building
cabling for telecom products and services. The three standards are formally titled
ANSI/TIA/EIA-568-B.1-2001, -B.2-2001, and -B.3-2001.

The TIA/EIA-568-B standards were first published in 2001. They supersede the TIA/EIA-568-A
standards set, which are now obsolete.

Perhaps the best known features of TIA/EIA-568-B.1-2001 are the pin/pair assignments for
eight-conductor 100-ohm balanced twisted pair cabling. These assignments are named T568A
and T568B, and are frequently referred to (erroneously) as TIA/EIA-568A and TIA/EIA-568B.

Contents
[hide]

 1 History
 2 Goals
 3 Structured cable system topologies
 4 T568A and T568B termination
o 4.1 Wiring
o 4.2 Use for T1 connectivity
o 4.3 Backwards compatibility
o 4.4 Theory
 5 See also
 6 References
 7 External links

[edit] History
TIA/EIA-568-B was developed through the efforts of more than 60 contributing organizations
including manufacturers, end-users, and consultants. Work on the standard began with the
Electronic Industries Alliance (EIA), a standards organization, to define standards for
telecommunications cabling systems. EIA agreed to develop a set of standards, and formed the
TR-42 committee, with nine subcommittees to perform the work.
The first revision of the standard, TIA/EIA-568-A.1-1991 was released in 1991, and was updated
in 1995. The demands placed upon commercial wiring systems increased dramatically over this
period due to the adoption of personal computers and data communication networks and
advances in those technologies. The development of high-performance twisted pair cabling and
the popularization of fiber optic cables also drove significant change in the standards, which
were eventually superseded by the current TIA/EIA-568-B set.

[edit] Goals
TIA/EIA-568-B attempts to define standards that will enable the design and implementation of
structured cabling systems for commercial buildings, and between buildings in campus
environments. The bulk of the standards define cabling types, distances, connectors, cable
system architectures, cable termination standards and performance characteristics, cable
installation requirements and methods of testing installed cable. The main standard, TIA/EIA-
568-B.1 defines general requirements, while -568-B.2 focuses on components of balanced
twisted-pair cable systems and -568-B.3 addresses components of fiber optic cable systems.

The intent of these standards is to provide recommended practices for the design and installation
of cabling systems that will support a wide variety of existing and future services. Developers
hope the standards will provide a lifespan for commercial cabling systems in excess of ten years.
This effort has been largely successful, as evidenced by the definition of category 5 cabling in
1991, a cabling standard that (mostly) satisfied cabling requirements for 1000BASE-T, released
in 1999. Thus, the standardization process can reasonably be said to have provided at least a
nine-year lifespan for premises cabling, and arguably a longer one.

All these documents accompany related standards that define commercial pathways and spaces
(569-A), residential cabling (570-A), administration standards (606), grounding and bonding
(607) and outside plant cabling (758).

[edit] Structured cable system topologies

TIA/EIA-568-B defines a hierarchical cable system architecture, in which a main cross-connect
(MCC) is connected via a star topology across backbone cabling to intermediate cross-connects
(ICC) and horizontal cross-connects (HCC). Telecommunications design traditions utilized a
similar topology, and many people refer to cross-connects by their older, nonstandard names:
"distribution frames" (with the various hierarchies called MDFs, IDFs and wiring closets).
Backbone cabling is also used to interconnect entrance facilities (such as telco demarcation
points) to the main cross-connect. Maximum allowable backbone cable distances vary between
300 m and 3000 m, depending upon the cable type and use.

Horizontal cross-connects provide a point for the consolidation of all horizontal cabling, which
extends in a star topology to individual work areas such as cubicles and offices. Under TIA/EIA-
568-B, maximum allowable horizontal cable distance varies between 70 m and 90 m for twisted-
pair cable types, depending upon patch cord length and gauge. Fiber optic horizontal cabling is
limited to 90 m. Optional consolidation points or transition points are allowable in horizontal
cables, although many industry experts discourage their use.

At the work area, equipment is connected to horizontal cabling by patch cords.

TIA/EIA-568-B also defines characteristics and cabling requirements for entrance facilities,
equipment rooms and telecommunications room.

[edit] T568A and T568B termination

Perhaps the widest known and most discussed feature of TIA/EIA-568-B.1-2001 is the definition
of pin/pair assignments for eight-conductor 100-ohm balanced twisted-pair cabling, such as
Category 3, Category 5 and Category 6 unshielded twisted-pair (UTP) cables. These assignments
are named T568A and T568B and they define the pinout, or order of connections, for wires in
8P8C (often incorrectly referred to as RJ45) eight-pin modular connector plugs and sockets.
Although these definitions consume only one of the 468 pages in the standards documents, a
disproportionate amount of attention is paid to them. This is because cables that are terminated
with differing standards on each end will not function normally.

TIA/EIA-568-B specifies that horizontal cables should be terminated using the T568A pin/pair
assignments, "or, optionally, per [T568B] if necessary to accommodate certain 8-pin cabling
systems." Despite this instruction, many organizations continue to implement T568B for various
reasons, chiefly associated with tradition (T568B is equivalent to AT&T 258A). The United
States National Communication Systems Federal Telecommunications Recommendations do not
recognize T568B.

The primary color of pair one is blue, pair two is orange, pair three is green and pair four is
brown. Each pair consists of one conductor of solid color, and a second conductor which is white
with a stripe of the same color. The specific assignments of pairs to connector pins varies
between the T568A and T568B standards.

Mixing T568A-terminated patch cords with T568B-terminated horizontal cables (or the reverse)
does not produce pinout problems in a facility. Although it may very slightly degrade signal
quality, this effect is marginal and certainly no greater than that produced by mixing cable brands
in-channel.

[edit] Wiring

See modular connector for numbering of the pins

T568A T568B
Pin Wire T568A Color T568B Color Pins on plug face (socket is reversed)
Pair Pair

1 3 2 tip white/green white/orange

stripe stripe
2 3 2 ring
green solid orange solid

3 2 3 tip white/orange white/green

stripe stripe
4 1 1 ring
blue solid blue solid

5 1 1 tip white/blue white/blue

stripe stripe
6 2 3 ring
orange solid green solid

7 4 4 tip white/brown white/brown

stripe stripe
8 4 4 ring
brown solid brown solid

Note that the only difference between T568A and T568B is that pairs 2 and 3 (orange and green)
are swapped. Both configurations wire the pins "straight through", i.e., pins 1 through 8 on one
end are connected to pins 1 through 8 on the other end. Also, the same sets of pins are paired in
both configurations: pins 1 and 2 form a pair, as do 3 and 6, 4 and 5 and 7 and 8. However the
different pairs in an Ethernet cable are identical, so one can use cables wired according to either
configuration in the same installation without significant problem; problems involving crosstalk
can occur (which is normally minimized by correctly twisting a pair together), but are usually
insignificant in all but the most stringent specifications such as Category 6 cable. The primary
thing one has to be careful of is not to accidentally wire the ends of the same cable according to
different configurations (except if one intends to create an Ethernet crossover cable).

[edit] Use for T1 connectivity

In T1 service, the pairs 1 and 3 (T568A) are used, and the USOC-8 jack is wired as per spec RJ-
48C. The Telco termination jack is often wired to spec RJ-48X, which provides for a Transmit-
to-Receive loopback when the plug is withdrawn.

Vendor cables are often wired with Tip and Ring reversed -- i.e. pins 1 and 2 reversed, or pins 4
and 5 reversed. This has no effect on the signal quality of the T1 signal, which is fully
differential, and uses the Alternate Mark Inversion (AMI) signaling scheme.

[edit] Backwards compatibility

Because pair 1 connects to the center pins (4 and 5) of the 8P8C connector in both T568A and
T568B, both standards are compatible with the first line of RJ11, RJ14, RJ25, and RJ61
connectors that all have the first pair in the center pins of these connectors.
If the second line of an RJ14, RJ25 or RJ61 plug is used, it connects to pair 2 (orange/white) of
jacks wired to T568A but to pair 3 (green/white) in jacks wired to T568B. This makes T568B
potentially confusing in telephone applications.

Because of different pin pairings, the RJ25 and RJ61 plugs cannot pick up lines 3 or 4 from
either T568A or T568B without splitting pairs. This would most likely result in unacceptable
levels of hum, crosstalk and noise.

[edit] Theory

The original idea in wiring modular connectors, which you see exemplified in the registered
jacks, was that the first pair would go in the center positions, the next pair on the next outermost
ones, and so on. Also, signal shielding would be optimized by alternating the "live" and "earthy"
pins of each pair. As you can see, the TIA/EIA-568-B terminations vary a little bit from this
concept. That's because on the 8 position connector, this results in a pinout in which the
outermost pair are too far apart to meet the electrical requirements of high-speed LAN protocols.