Scribd
Upload
334 views3 pages

Tds Pattex CF 1000

Epoxy material for steel bar anchorage in to hardened concrete member

Uploaded by

Safi Zabihullah Safi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
334 views3 pages

Tds Pattex CF 1000

Epoxy material for steel bar anchorage in to hardened concrete member

Uploaded by

Safi Zabihullah Safi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 3
nm Epoxy-Resin-System CONCRETE / SOLID STONE 11, AREAS OF APPLICATION LUNDERSURFACE: Concrete, solid stone + For concrete + For building works of reconstruction and renovation 1. Dall hole wih + For difficult anchoring in each kind of material percussion cal 2. BENEFITS: + Cartrige can be used up to the end of the validity date by replacing the static mixer or resealing cartrige with sealing cap + Water-impermeable joint, .e.no water can penetrate into the hole at the side of the adhesive compound |. PROPERTIES. * High chemical resistance + Flexible working time at elevated temperatures * Good wetting ability + Flexible setting of bore diameter/anular gi + Good performance in diamond drilled holes + No shrinkage + Performance approved by the independent Institute EMPA (report no. 431 899 1) + Strong and secure anchoring even under water + Transport- and storage-temperatures: +5°C to +25°C oroptwe oc 180 Min soh 00h we 120M uh Bh we 30 Min oh 2h we 20 Nin 6h Dh we 12Min 4h th 2. Clean aihoia (Blow out: 4x, brush (ut: 4x blow out 4) 3. Screw mer fo cattidge 4 Squeeze out and card approx. 1.6m of compound befere use 8. Stating ftom the backend, fl hole completely ‘wth mete 6. Push anchor up to ase of hole whist suming tightly 7. Vauai check of meter ting 18, Obsenve hardening time 9. Install component, ‘apply torque Pattex’ CF 1000 ies Fite Technical information Ae Epoxy-Resin-System PERFORMANCE DATA / STANDARD APPLICATION IN CONCRETE resin ‘Concrete: = 20/25 TKNI y TKN] tension loads ety Tactor for tension Toads 1,8 acc. to FTAG TEN IkNI steel quality 5.8 torque share loads TEN IKNI steel quality At Concrete recommended loads in 2 20/26 every direction ‘edge distance Tain. edge distance ‘axial distance Tin. axial distance anchorage depth minimum partthicknes thread diameter ‘drill Tiameter Tole diameter tn part ‘tightening torgue ‘ky concrete submerged concrete re Pete] CF 1000 Technical information Epoxy-Resin-System ee PERFORMANCE DATA / REBAR APPLICATION IN CONCRETE rebar diameter [Draw [ime wl etul wl «fol » [sl ml 2] «| 0 sressarea [AC firm) _[ sas) 745 reat | 1.9[ 20u1 | asus [oraz | ene | was] «158 oow2 | vor79 | rome erste strength [ig [Nin] EI eld stress Tx. IN a. hoe dames Domi [oTet «lela, = [sl =lolsl,~| nl] e A A iment depih minhfinmmi | wo fo nol ws [ms] wo | wo] wo | 20] | v0 = characteristic value of the bonding strength legn value of the bonding strength induding the safety factor 2.16 C20/25 ‘submerged concrete 25/30 08, (C30/37 ‘C40/50, ‘The basic anchorage length |, can be calaulated from ly = (0X fyal / (4 X fa fee) with f,adesign yield strength of post installed rebar.

You might also like