Scribd
Upload
1K views

Exp 4

This document describes measuring the value of an unknown capacitance using de Sauty and Schering bridges. The de Sauty bridge uses the Wheatstone bridge principle to calculate the unknown capacitance Cx based on known resistances R1 and R2. The Schering bridge improves on the de Sauty bridge by enabling measurement of very low capacitance values. Experimental results show the unknown capacitance measured with the de Sauty bridge is 0.446μF and 4.4487μF, close to the known values of 0.454μF and 4.452μF measured with an LCR bridge. The unknown capacitance measured with the Schering bridge is 0.449μF.

Uploaded by

Rakesh Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Exp 4

This document describes measuring the value of an unknown capacitance using de Sauty and Schering bridges. The de Sauty bridge uses the Wheatstone bridge principle to calculate the unknown capacitance Cx based on known resistances R1 and R2. The Schering bridge improves on the de Sauty bridge by enabling measurement of very low capacitance values. Experimental results show the unknown capacitance measured with the de Sauty bridge is 0.446μF and 4.4487μF, close to the known values of 0.454μF and 4.452μF measured with an LCR bridge. The unknown capacitance measured with the Schering bridge is 0.449μF.

Uploaded by

Rakesh Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

AC Bridges : Measuring Capacitance using

de Sauty and Schering Bridges

Ravitej Uppu

Aim
To measure the value of the unknown capacitance using the method of de
Sauty and Schering bridges.

1 Theory
Bridges are the some of the most accurate measuring devices for measuring
impedance, capacitance, resistance,etc. For our purpose, i.e. for measuring
Capacitance, using a de Sauty’s or Schering bridge is best. They are based
on the principle of Wheatstone bridge that they have two arms. One of
which has the unknown parameter. By getting the bridge balanced using
the Null detector we can find this value.
The de Sauty’s bridge is a direct carry over of the Wheatstone bridge
with the DC source replaced by an AC source. The null detector we will
be using also has an amplifier where the gain can be adjusted. This is con-
nected to DMM which is used for getting the null point. The bridge is as

follows. We can use the princi-


R1 C
ple of wheat stone bridge to calculate Cx as Cx = R2 .

1
AC Bridges - Ravitej Uppu

A Schering bridge is a alternating-current bridge used to measure ca-


pacitance and dissipation factor; bridge balance is independent of frequency.It
is an improvement over the de Sauty Bridge in that it enables an accurate
measurement of very low capacitance too due to the parallel capacitor ele-
ment which is useful in getting the sensitivity for a better balance. Though
the bridge takes longer for the balancing. The bridge setup is as follows.

2 Procedure
Connect the circuit as shown in the figures above. For the de Sauty bridge,
set the frequency to about 1KHz on the function generator and set the gain
on the null detector to max. Now balance the bridge by varying the ca-
pacitance(C) and resistance (R2 ) until we get the most stable and best null
point. Do this for various values of R1 and also for different frequencies.
For Schering bridge, do the same as above and balance the bridge with
the extra fact that use the Capacitance box given in parallel to get a stable
balance. From the read off values we can calculate the unknown capaci-
tance as Cx = RRs CBA .

2
AC Bridges - Ravitej Uppu

3 Observations and Results


de Sauty bridge
Frequency = 1.073KH

S.No R1 Ω R2 Ω C µF Cx µF
1 400 400 0.4493 0.4493
2 300 403 0.5877 0.4375
3 400 298 0.3359 0.4509
4 400 492 0.5473 0.4450
5 500 400 0.3558 0.4447
6 4000 4000 0.4528 0.4528
7 1000 1000 0.4458 0.4458

Frequency = 15.13KHz The stabilization gets more difficult with a in-


crease in frequency. Otherwise there is not change in the value. The exper-
iment ids independent of the frequency.

S.No R1 Ω R2 Ω C µF Cx µF
1 500 500 0.4432 0.4432
2 200 203 0.4423 0.4356
3 400 308 0.3658 0.4751
4 300 204 0.3029 0.4454

Frequency = 1.073KhZ. The factory value of unknown resistance is


4.7µF

S.No R1 Ω R2 Ω C µF Cx µF
1 1000 1000 4.9873 4.9873
2 400 406 4.4996 4.4331
3 400 305 3.2868 4.3106
4 300 398 5.9543 4.4882
5 200 396 9.0243 4.5577
6 400 205 2.2065 4.4054

• From table 1, the value of unknown resistance is = 0.446µF


• From table 2, the value of unknown resistance is = 0.449µF
• From table 3, the value of unknown resistance is = 4.4487µF
• The value of capacitance 1 using the LCR bridge equipment is 0.454µF .
• The value of capacitance 2 using the LCR bridge equipment is 4.452µF .

3
AC Bridges - Ravitej Uppu

Schering Bridge
Frequency =1.003KHz.

S.No Rx Ω RB Ω CA µF
1 1000 483 1 0.4830
2 1200 597 1 0.4875
3 800 367 1 0.4587
4 700 312 1 0.4457
5 600 269 1 0.4479
6 500 223 1 0.4465

The value of unknown capacitance is = 0.461µF . We have seen a gen-


eral trend that the bridge balance is better at lower resistance values. So,
if we take the better stabilized values, then the value of capacitance is
= 0.449µF .

You might also like