Scribd
Upload
213 views

Bit Nozzle (S) Pressure Drop: Nozzle Numbers Nozzle Dia in Decimal in Flow Area in

This document contains information about the nozzle pressure drop for a bit with 8 nozzles of varying diameters. It lists the nozzle number, diameter in decimal inches, flow area in square inches, and calculates the total flow area, flow rate in gallons per minute, fluid density in pounds per gallon, and resulting pressure drop in psi. It also contains information about calculating pressure drop through a pipe, including inputs for pipe ID and length, flow rate, fluid density and viscosity, roughness factor. It displays the calculated velocity, Reynolds number, friction factor looked up from a chart based on Reynolds number and roughness ratio, resistance coefficient, and resulting pressure drop in psi.

Uploaded by

njileo
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
213 views

Bit Nozzle (S) Pressure Drop: Nozzle Numbers Nozzle Dia in Decimal in Flow Area in

This document contains information about the nozzle pressure drop for a bit with 8 nozzles of varying diameters. It lists the nozzle number, diameter in decimal inches, flow area in square inches, and calculates the total flow area, flow rate in gallons per minute, fluid density in pounds per gallon, and resulting pressure drop in psi. It also contains information about calculating pressure drop through a pipe, including inputs for pipe ID and length, flow rate, fluid density and viscosity, roughness factor. It displays the calculated velocity, Reynolds number, friction factor looked up from a chart based on Reynolds number and roughness ratio, resistance coefficient, and resulting pressure drop in psi.

Uploaded by

njileo
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 2

Nozzle Pressure

BIT NOZZLE(S) PRESSURE DROP


Nozzle Dia
Nozzle Numbers in Decimal Flow Area
in in2
Nozzle #1; ( X/32" ) = 18 0.56250 0.24850
Nozzle #2; ( /32" ) =
X
12 0.37500 0.11045
Nozzle #3; ( /32" ) =
X
12 0.37500 0.11045
Nozzle #4; ( /32" ) =
X
12 0.37500 0.11045
Nozzle #5; ( X/32" ) = 12 0.37500 0.11045
Nozzle #6; ( X/32" ) = 12 0.37500 0.11045
Nozzle #7; ( X/32" ) = 0 0.00000 0.00000
Nozzle #8; ( X/32" ) = 0 0.00000 0.00000
Total Flow Area A, in2 = 0.80074
Flow Rate Q; gpm = 755.00
Fluid Density (weight) W; ppg = 14.700
Pressure Drop D p, psi = 1,203.60
Drilex Operation HandBook, p.12

Enter Nozzle Sizes


Enter Flow Rate
Enter Fluid Density

Page 1
Pipe Pressure

PRESSURE DROP THROUGH PIPE


INPUT in Feet
Pipe id, in D 1 0.083 ft
Pipe Length, in L 45 3.750 ft
Flow rate, gpm Q 200 0.446 ft3/s
Density, slug/ft3 r 1.937
Viscosity, lbf.s/ft2 m 2.09E-05
Roughness factor e 8.50E-04
OUTPUT
Velocity V 8.170E+01 ft/s
Re number Re 6.304E+05
e/d e/d 1.020E-02
friction factor f 3.800E-02 <-from chart
Resistance coeff K 1.710E+00
Pressure Drop Dp 77 psi

1. Enter d, L, Q, r, m, e
2. Enter friction factor f based on Re and e/d
3. Read Pressure drop in cell D15
4. Mark's M.E. handbook

Page 2

You might also like