CCNA Lab Sim Category
CCNA Lab Sim Category
Question
This task requires you to use the CLI of Sw-AC3 to answer five multiple-choice questions. This does not require any configuration.
To answer the multiple-choice questions, click on the numbered boxes in the right panel.
There are five multiple-choice questions with this task. Be sure to answer all five questions before leaving this item.
READ MORE
Question
A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance
Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location
including other resources on the Finance Web Server, all other traffic should be allowed.
The task is to create and apply a numberd access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web
access to the Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.
READ MORE
Question
An administrator is trying to ping and telnet from Switch to Router with the results shown below:
Switch>
Switch> ping 10.4.4.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.4.4.3,timeout is 2 seconds:
.U.U.U
Success rate is 0 percent (0/5)
Switch>
Switch> telnet 10.4.4.3
Trying 10.4.4.3
% Destination unreachable; gateway or host down
Switch>
Click the console connected to Router and issue the appropriate commands to answer the questions.
READ MORE
Question
You work as a network technician at 9tut.com. Study the exhibit carefully. You are required to perform configurations to enable Internet access. The Router ISP has given you six public
IP addresses in the 198.18.32.65 198.18.32.70/29 range.
9tut.com has 62 clients that needs to have simultaneous internet access. These local hosts use private IP addresses in the 192.168.6.65 192.168.6.126/26 range.
You need to configure Router1 using the PC1 console.
You have already made basic router configuration. You have also configured the appropriate NAT interfaces; NAT inside and NAT outside respectively.
Now you are required to finish the configuration of Router1.
Solution
READ MORE
Well, the title said it all. Here are some screenshots about the labs in Packet Tracer Simulator:
(Hint: use the given host addresses and Main router information)
To remove a device or connection, drag it away from the topology.
Use information gathered from the Main router to complete the configuration of any additional routers. No passwords are required to access the Main router. The config
terminal command has been disabled for the HQ router. The router does not require any configuration.
Configure the interfaces with the correct IP address and enable the interfaces.
Set the password to allow console access to consolepw
Set the password to allow telnet access to telnetpw
Set the password to allow privilege mode access to privpw
Note: Because routes are not being added to the configurations, you will not be able to ping through the internetwork.
All devices have cable autosensing capabilities disabled.
All hosts are PCs
Answer and explanation
READ MORE
Question
After adding R3 router, no routing updates are being exchanged between R3 and the new location. All other inter connectivity and Internet access for the existing locations of the
company are working properly.
The task is to identify the fault(s) and correct the router configuration to provide full connectivity between the routers.
Access to the router CLI can be gained by clicking on the appropriate host. All passwords on all routers are cisco.
S0/0: 192.168.36.13
R3 R4
READ MORE
Question
You have been hired by Specialty Hardware Incorporated to document the layout of the network. Complete the following tasks: Complete the network topology shown in the graphic by
dragging the labels below with the appropriate router types, interface types, and IP addresses to the graphic . Find the information you need by using the router console attached to the
R-CENTER router.
Answer and explanation
READ MORE
Question:
To configure the router (R2-RC) click on the console host icon that is connected to a router by a serial console cable (shown in the diagram as a dashed black line)
CCNA Training Company recently installed a new router in their office. Complete the network installation by performing the initial router configurations and configuring RIPV2 routing
using the router command line interface (CLI) on the R2-RC.
Name of the router is R2-RC
Enable-secret password is cisco1
The password to access user EXEC mode using the console is cisco2
The password to allow telnet access to the router is cisco3
IPV4 addresses must be configured as follows:
Ethernet network 209.165.202.128/27 router has last assignable host address in subnet
Serial network is 192.0.2.16/28 router has last assignable host address in the subnet. Interfaces should be enabled.
Router protocol is RIP V2
Attention :
In practical examinations, please note the following, the actual information will prevail.
1. Name of the router is xxx
2. Enable-secret password is xxx
3. Password to access user EXEC mode using the console is xxx
4. The password to allow telnet access to the router is xxx
5. IP information
Solution
READ MORE
Question
A network associate is configuring a router for the CCNA Training company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105
198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the CCNA Training company LAN have been assigned private space addresses in
the range of 192.168.100.17 192.168.100.30.
The task is to complete the NAT configuration using all IP addresses assigned by the ISP to provide Internet access for the hosts in the Weaver LAN. Functionality can be tested by
clicking on the host provided for testing.
Configuration information
router name Weaver
inside global addresses 198.18.184.105 198.18.184.110/29
inside local addresses 192.168.100.17 192.168.100.30/28
number of inside hosts 14
- The appropriate interfaces have been configured for NAT inside and NAT outside
- The appropriate static routes have also been configured (since the company will be a stub network, no routing protocol will be required.)