Scribd
Upload
47 views2 pages

Lower Right Gusset Interface - Beam: Directly Welded

This document summarizes the design checks for load demands on a lower right gusset interface connecting a beam and column. It lists the load descriptions and values, then verifies several capacity checks for the gusset, beam, and connecting angles against the demands to ensure ratios are below limits according to referenced design standards. Key checks include weld capacities, stresses, web crippling, local web yielding, and geometric requirements for the angle connections. The overall ratio of the highest demand to capacity is 0.04, below the acceptable limit.

Uploaded by

Min Khant Kyaw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
47 views2 pages

Lower Right Gusset Interface - Beam: Directly Welded

This document summarizes the design checks for load demands on a lower right gusset interface connecting a beam and column. It lists the load descriptions and values, then verifies several capacity checks for the gusset, beam, and connecting angles against the demands to ensure ratios are below limits according to referenced design standards. Key checks include weld capacities, stresses, web crippling, local web yielding, and geometric requirements for the angle connections. The overall ratio of the highest demand to capacity is 0.04, below the acceptable limit.

Uploaded by

Min Khant Kyaw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Lower right gusset interface - beam

Directly welded
DEMANDS
Beam Column
Description Ru Pu Mu Pu Mu22 Mu33 Load type
[Kip] [Kip] [Kip*ft] [Kip] [Kip*ft] [Kip*ft]
----------------------------------------------------------------------------------------------------------------------------------
DL 2.47 1.29 0.00 0.00 0.00 0.00 Design
----------------------------------------------------------------------------------------------------------------------------------

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Gusset
Beam yielding (normal stress) [Kip] 162.62 1.29 DL 0.01 Eq. B-1,
Appendix B,
DG29, Eq. J4-1
Shear yielding [Kip] 108.41 2.47 DL 0.02 Eq. J4-3
Gusset edge tension stress [Kip/in2] 32.40 0.26 DL 0.01 J4-1
Gusset edge shear stress [Kip/in2] 21.60 0.49 DL 0.02 J4-1
Weld capacity [Kip] 83.22 3.49 DL 0.04 Tables 8-4 .. 8-11
Beam
Weld block shear [Kip] 91.01 2.47 DL 0.03 Eq. J4-5
Web crippling [Kip] 110.25 1.29 DL 0.01 Eq. J10-4,
Eq. B-1,
Appendix B,
DG29
Local web yielding [Kip] 84.39 1.29 DL 0.02 Eq. J10-3,
Eq. B-1,
Appendix B,
DG29
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.04
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Lower right gusset interface - column


Angles
DEMANDS
Description Ru Pu Load type
[Kip] [Kip]
-------------------------------------------------------------------
DL 1.23 0.05 Design
-------------------------------------------------------------------

GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Angle (Gusset side)


Weld size [1/16in] 3 2 3 table J2.4,
Sec. J2.2b
Angle (Column side)
Vertical edge distance [in] 1.25 0.88 -- Tables J3.4,
J3.5
Horizontal edge distance [in] 1.11 0.88 -- Tables J3.4,
J3.5

Page5
Vertical center-to-center spacing (pitch) [in] 1.88 1.67 3.78 Sec. J3.3,
Sec. J3.5
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Angle (Gusset side)


Weld capacity [Kip] 47.02 1.23 DL 0.03 Tables 8-4 .. 8-11
Shear yielding [Kip] 29.76 1.23 DL 0.04 Eq. J4-3
Leg tensile yielding [Kip] 44.65 0.05 DL 0.00 Eq. J4-1
Angle (Column side)
Bolts shear [Kip] 49.73 1.23 DL 0.02 Tables (7-1..14)
Bolt bearing under shear load [Kip] 34.42 1.23 DL 0.04 p. 7-18,
Sec. J3.10
Shear yielding [Kip] 29.76 1.23 DL 0.04 Eq. J4-3
Shear rupture [Kip] 23.63 1.23 DL 0.05 Eq. J4-4
Block shear [Kip] 26.05 1.23 DL 0.05 Eq. J4-5
Resulting tension capacity due prying action [Kip] 4.62 0.05 DL 0.01 p. 9-11,
p. 9-10
Gusset
Welds rupture [Kip/ft] 208.80 3.00 DL 0.01 p. 9-5
Shear yielding [Kip] 80.78 1.23 DL 0.02 Eq. J4-3
Tear out under axial load [Kip] 125.32 0.05 DL 0.00 Eq. J4-5
Column
Bolt bearing under shear load [Kip] 80.15 1.23 DL 0.02 Eq. J3-6
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.05
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Right beam interface - column


Single plate
DEMANDS
Beam Column
Description Ru Pu Pu Mu22 Mu33 Load type
[Kip] [Kip] [Kip] [Kip*ft] [Kip*ft]
-------------------------------------------------------------------------------------------------------------------
DL 0.18 9.63 40.58 0.00 0.00 Design
-------------------------------------------------------------------------------------------------------------------

GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Shear plate
Length [in] 4.75 3.62 7.24 p. 10-104
Thickness [in] 0.25 -- 0.31 p. 10-102
Number of bolts 2 2 12 p 10-102
Distance from the bolt line to the weld line [in] 3.00 -- 3.50 p 10-102
Minimum plate or beam web thickness [in] 0.22 -- 0.31 Table 10-9
Vertical edge distance [in] 0.88 0.75 -- Tables J3.4,
J3.5
Horizontal edge distance [in] 1.25 1.00 -- p. 10-103

Page6

You might also like