Scribd
Upload
429 views2 pages

Larsen & Toubro Limited: ECC Division - EDRC

This document provides calculations to check the crack width for a footing (F17) under maximum moment (M) of 1389 kN-m for the Delhi International Airport Terminal 3 project. It calculates the crack width (Wcr) of 0.08 mm, which is less than the permissible limit of 0.20 mm. Therefore, the crack width is within the acceptable limit as per IS:456-35.3.2.

Uploaded by

selva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
429 views2 pages

Larsen & Toubro Limited: ECC Division - EDRC

This document provides calculations to check the crack width for a footing (F17) under maximum moment (M) of 1389 kN-m for the Delhi International Airport Terminal 3 project. It calculates the crack width (Wcr) of 0.08 mm, which is less than the permissible limit of 0.20 mm. Therefore, the crack width is within the acceptable limit as per IS:456-35.3.2.

Uploaded by

selva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 2

LARSEN & TOUBRO LIMITED

ECC Division - EDRC

PROJECT:
DELHI INTERNATIONAL AIRPORT LIMITED - TERMINAL - 3 AIRSIDE DOCUMENT NO. DATE
& LANDSIDE WORKS 8/12/2017
DESIGNED CHECKED SHEET
TITLE: FOOTING F17-CRACK WIDTH CHECK FOR MAX MOMENT
RDN MVH

CHECK FOR CRACK WIDTH (As per IS 456 : 2000 ANNEX F):

GRADE OF CONCRETE fck = 40 N/mm2

MOMENT AT THE SECTION CONSIDERED M = 1389 kN-m

OVERALL DEPTH OF THE SECTION h = 2000 mm


THE WIDTH OF THE SECTION AT THE CENTROID OF
THE TENSION STEEL b = 1000 mm

MINIMUM COVER TO THE LONGITUDINAL BAR Cmin = 75 mm

DIA OF BAR = 25 mm

EFFECTIVE DEPTH d = 1912.5 mm

COVER TO THE COMPRESSION STEEL d' = 75 mm

DISTANCE FROM THE POINT CONSIDERED TO THE acr


SURFACE OF THE NEAREST LONGITUDINAL BAR = 85.13 mm

AREA OF TENSION STEEL As = 3926.9908 mm2

AREA OF COMPRESSION STEEL Asc = 0 mm2


DISTANCE FROM THE COMPRESSION FACE TO THE
POINT AT WHICH THE CRACK WIDTH IS BEING a = 2000 mm
CALCULATED

MODULUS OF ELASTICITY OF STEEL Es = 2.00E+05 N/mm2

MODULUS OF ELASTICITY OF CONCRETE EC = 31623 N/mm2


LONG TERM MODULUS OF ELASTICITY OF Ece
CONCRETE = 15058 N/mm2

MODULAR RATIO m = Es/Ece 13.3

DEPTH OF NEUTRAL AXIS x = 397.5 mm

CRACKED MOMENT OF INERTIA Icr = bx3/3+mAt(d-x)2 1.41E+11

SERVICE STRESS IN TENSION REINFORCEMENT fs = mM(d-x)/Icr 199 N/mm2

STRAIN AT THE LEVEL CONSIDERED, e1 = ((h-x)/(d-x))fs/Es 0.00105

em = e1- b(h-x)(a-x) 0.00033


3EsAs(d-x)

DESIGN SURFACE CRACK WIDTH 3acrem


Wcr= 0.08 mm
1 + 2(acr-Cmin)/(h-x)
PERMISSIBLE CRACK WIDTH (IS:456-35.3.2 Page-67) = 0.20 mm OK

You might also like