Dear customer,

Thank you very much for your purchasing of the 2- way Motorcycle Alarm system manufactured by us. This
product featured with multi-functions is designed for anti-theft protection of all 12V motorcycles. Before use, read
the manual carefully for full understanding of all the features.

System function guide

Icon pictures on 2-way LCD ........................................ 2 Remote check of cycle status..................................... 6

Icons to view during adjusting sensor sensitivity.......... 2 Cycle search ............................................................. 6

Remote control quick chart........................................... 3 Remote panic............................................................. 6

Remote arm (audio /mute) alert.................................... 4 Remote anti-carjack ON/OFF........................................

Remote disarm.............................................................. 4 6

Remote siren OFF/ON ................................................. 4 Adjusting internal shock sensor sensitivity....................

Auto arm....................................................................... 5 6

Immobilizer ON/OFF................................................... 5 Adjusting tilt sensor sensitivity.....................................

Remote valet ON /OFF................................................. 5 7

Shock sensor bypass..................................................... 5 Arm mode & warn away...............................................

Tilt sensor bypass......................................................... 6 7

Pin code ON/OFF............................................................. Out-of-range features....................................................

8 10

Manual disarm (In case the remote transmitter is lost)...... Monitoring standby indication.......................................

8 10
Systems learning of new remotes codes......................... Low battery indicator for transmitter.............................

9 10

Reminder of allowed number of remotes.......................... Remote Controls other Functions ................................

10 11

Hopping code technology................................................. Alarm module wiring diagram ......................................

10 12

Packing list

Main system 1 2-WAY LCD Remote 1 1-WAY Remote 1 12 pin wire 1 Manual 1

Icon pictures on 2-way LCD

1.Disarm 2.Silent arm 3.Audible arm 4. Sensor light 5. Sensor heavier

impact bypass impact bypass

6.Shock Sensor 7. Tilt Sensor 8.Tilt Sensor 9.Valet on 10.Ignition ON

trigger bypass trigger

11. Negative 12.Negative 13.Immobilize 14.Auto arm 15. Pin code

trigger 1 input trigger2 input

 16.Low battery 17.Antenna 18.Alarm clock 19.Clock radio 20.Count down

Icons to view during adjusting sensor sensitivity

21.Ready to 22.Ready to accept 23.Failure and jump 24.Customerss

heavy impact out adjustment mode
accept ligth completed

impact

Remote control quick chart

 The two-way and one-way remotes function table

Indicates Press and release of specified button

For 2 way remote, it indicates Press and hold specified button for 1 second (LCD vibrates and beeps) then enters deep command mode.

For one way remote, it indicates Press and hold specified button for 1 second (LED lights green) then enters deep command mode

(s1 ) Indicates Press button twice within 1 sec.

Short guide of button/buttons being used and procedure

Pre-condition
Function to activate =button 1 =button 2
before functioning
=button 3

Arm When Ignition OFF

Disarm When Ignition OFF

Shock Sensors bypass under arm mode

Tilt Sensors bypass under arm mode

Audible /Silent choice When Ignition OFF

Check status Under any condition

Cycle search (s1 ) Under any condition

Panic with When Ignition OFF

 Remote Anti carjack On with When Ignition ON

Auto arm On/Off Any condition

Immobilize On/Off Any condition

Valet Mode On/ Off Under disarm mode

Adjust shock sensor Under disarm

Adjust sensor less sensitive At adjust mode

Adjust sensor more sensitive At adjust mode

Adjust tilt sensor Under disarm

Adjust sensor less sensitive under adjust mode

Adjust sensor more sensitive Under adjust mode

with
Button-pad lock
LED glows orange if button-pad was locked
Under any condition
with
Button-pad unlock
LED glows red if button-pad was locked

Remote arm (audible and mute) alert

1. When Ignition OFF, press and release button 1 .Siren chirps 1 time (or no chips only in mute mode) followed by 1 flash

of

parking light. The system enters arm mode and LED will flash under arm mode. Refer LCD guide No.2 or 3.

2. Defective zone bypass

If system in arm mode is triggered by shock sensor or tilt sensor(The part is unusual) , it will temporary and automatically bypass

the defective zone, until defective zone is corrected, the system re-enter full arm mode.

Note: When ignition is ON, press and release button 1 or button 2 , there are only check motorcycle status

by the system.

Remote disarm
1. Press and release button 2 The main system is disarmed. Siren sound 2 chirps (or no chips only in mute mode) with

2 parking light flashes.

2. Security diagnostic report and stage disarm

If triggered under arm mode, the triggered zones display in the LCD screen and siren chirps 4 times.

Auto rearm

Within 50 seconds from disarm , if ignition is not turned ON, system will re-arm itself .
 Remote siren OFF/ON mode
1. Ignition must be at OFF position. Press and hold button 2 to enter deep-command first. Then press release

button 2 again to select siren On or OFF. If siren ON is selected , the LCD screen will display siren-ON icon. For icon

display, refer LCD picture No.2 or 3

2. Under audible mode, siren sounds differently in accordance to remote command.

3. Under mute mode, siren makes no sound except motorcycle search command.

Auto arm
1. Under auto arm mode: The system is armed after 50 seconds from ignition OFF.

2. Press and hold button 1 to enter deep command first. Then press and release button 1 to select On/Off Auto

arm. Under auto arm ON mode, LCD screen will display auto-arm icon. For icon display ,refer to LCD picture No.14

Immobilizer mode ON/OFF

Under immobilizer mode: The system is immobilized after 50 seconds from ignition OFF.

Under immobilizer mode, parking light flashes whenever ignition is ON.

1. Press and hold button 1 to enter deep-command. Then press and release button 2 again to select ON/OFF

immobilizer mode. Refer LCD picture No.13

2. Under immobilizer ON mode, system automatically enters immobilizer mode (engine defeat relay is activated) after 50 sec from

ignition OFF. Under this mode, engine start by the ignition key is disabled

3. To de-immobilize, press and release button 2 when IGN is Off.

Remote valet ON /OFF

1. To enable valet mode function ,the system must be under disarm mode and immobilizer mode off.

2. Press and hold button 1 enter deep-command first. Then press and release button 3 again to select valet On or

OFF. Under valet ON mode, LCD screen will display Valet ON icon .For icon display, refer to LCD picture No.9

3. Under Valet ON mode, all functions are inoperative

Shock sensor bypass

1. To enable sensor bypass, system must be under arm mode. Press and release button 1 twice. The first stage internal

shock sensor is bypassed. For icon display , refer to picture No.4

2. Under sensor 1st stage bypass mode, press and release button 1 twice. shock sensor 2nd stage is bypassed. Refer picture

No.5

3. Under sensor 2nd stage bypass mode, press and release button 1 twice. All bypass stages are cleared and sensors can re-

work normally..
 Tilt sensor bypass
1. To enable this bypass, system must be in arm mode. Press and release button 2 twice. The tilt sensor is

bypassed. Refer picture No.7. Under tilt sensor bypass mode, press and release button 2 twice The tilt sensor bypass is

cleared and it can work normally.

Remote check motorcycle status

1. Press and release button 3 to check the current cycle status.

2. The current cycle status will display on LCD screen

Cycle search
1. Either the system into arm or disarm and alert or mute mode.

2. Press and release twice button 3 .The siren chirps 6 times with 6 flashes of parking light for owner to easily locate the

cycle.

Remote panic
1. To enable panic ,ignition must OFF

2. Press and hold 1 whit 2 button, the parking light flashes 10 times and siren chirps 10 times. The system will
 enter arm mode.

Remote anti-carjack ON/OFF

1. To enable this feature, ignition must ON.

2. Press and hold 1 and 2 button simultaneously. The system will enter anti-carjack trigger mode, parking light and

siren continuous flashes and alert 45 sec and engine is immobilized .

3. While the remote anti-carjack is being activated, press and release button 2 once to terminate alarm triggering. The next

press and release of button 2 makes the main system enter disarm mode.

Adjusting internal shock sensor sensitivity

Micro adjustment method:
1. To enter sensor adjustment mode, press & hold 3 and then press and release1again.
2. The current sensitivity level is displayed on the LCD screen and system sounds beeps.
3. Each press on1 can adjust sensitivity downwards one level . Each press on2 can adjust sensitivity upwards one level. ( There
are total 8 levels. Level 1 is the most sensitive and 8 is the least sensitive).
4. To jump out of adjustment mode, press & hold 3and then press and release1again.
Customers adjustment method
1. To enter sensor adjustment mode, press & hold 3 first , then press and release 1 again.

2. Press momentarily 3 2 times. System will sound 2 long beeps and enter customers adjustment mode.

3. When LCD displays icon (Refer to picture No.21) following systems 1 long beep, strike light impact on to the cycle. System will
 sound one short beep to confirm ending of this setting.
4. Again strike heavy impact on to the cycle when icon (Refer to picture No.22) displays. If system sounds 2 short beeps, this setting is
done.
5. System will automatically jump out.the sensor adjustment mode in the end.
6. During any process of sensnor adjustment, the settings will be nullified under 2 conditions below
A) If light impact is not received by the system within 10 sec while picture No.21 displays. The system will sound 4 beeps
and LCD display icon (Refer to picture No.23) to notify nullify.
B) If heavy impact is weaker than light impact, the system does not recognize this and will nullify this process. Strike
heavy impact again.
7. At the end of customers adjustment mode (Refer to picture No.24) , it is not possible to access to micro adjustment mode with 1~8
sensitivity levels.
8. To re-do the customers adjustment or to jump-out , firstly enter into the shock sensor adjust mode and then press temporarily32
times for the cancellation of customers adjustment mode and jump-out .
After that, when you enter adjust mode, system starts from the micro-adjustment ( 1~ 8 ). Follow the same step 1 ~ 8 as above to do
adjustment.

Adjusting tilt sensor sensitivity

1. System must be disarm mode and ignition at OFF position. Press and hold button 3 enter deep-command .Then

press and release button 2 to achieve active adjustment mode .

2. Press and release button 1 each time to adjust to lesser sensitivity

3. Press and release button 2 each time to adjust to better sensitivity.

4. If desired sensitivity is reached, Press and hold button 3 enter deep-command. Then press and release

button 2 to jump out of adjust mode.

Note There are 8 sensitivity levels. During adjustment, the level reached is indicated by siren chirps. On the LCD s screen,
 numerical will also show the sensitivity level.

Arm mode & warn away

1. In arm mode If trigger is caused by shock sensor ,parking light will flash and siren chirps. Refer to LCD picture No 6. If

detects tilt sensors is triggered. Parking light will flash. Refer LCD picture No 8.

2. In arm mode When negative(-) trigger input, parking light will flash and siren chirps. Refer to LCD picture No 11&12.

3. While the alert is being triggered in arm mode, press and release button 2 once to terminate alarm triggering. The next

press and release of button 2 makes the main system enter disarm mode.

PIN code ON/OFF

1. During disarm mode , turn ignition ON-OFF-ON-OFF-ON-OFF and stay it at OFF position to enter 1st

stage, LED will glows for 3 seconds. 3 seconds later, LED will turn off .

2. When LED turn off, system enter 2nd stage. Immediately turn ignition ON-OFF-ON-OFF-ON-OFF-ON

and complete this process within 5 sec. Ignition stay at ON position. The siren will sound 4 blurts and

system will enter PIN code set mode.

3. Press and release remote button 1 2 or 3 button to set PIN code numbers.

3.1)

To assign PIN code digit number at 1 time. Press and release button of the remote unit. The siren 1 chirp to confirm.

3.2)

To assign PIN code digit number at 2 time. Press and release button of the remote unit. The siren 2 chirp to confirm.

3.3)

To assign PIN code digit number at 3 time. Press and release button of the remote unit. The siren 3 chirp to confirm.

3.4)

To assign PIN code digit number at 4 time. Press and release button of the remote unit. The siren 4 chirp to confirm.

3.5)

To assign PIN code digit number at 5 time. Press and release button of the remote unit. The siren 5 chirp to confirm.

4. Must to input 4 numbers, if not the pin code numbers set will be fail. When pin code numbers set finish,

the system will automatic jump out pin code numbers set mode.

5. If you want turn off PIN code mode, press and release twice button 3 , the system will turn off PIN code

mode.

Manual disarm (In case the remote transmitter is lost)

1. During alarm trigger, turn the ignition to ON. Wait for the siren to stop blurting.
2. Then immediately turn ignition OFF-ON-OFF-ON-OFF and complete this process within 3 seconds. LED will glows for 3 seconds.
3 seconds later, LED will turn off .
3. When LED turn off, immediately turn ignition ON-OFF-ON-OFF-ON-OFF and complete this process within 3 sec. The siren will
sound 2 blurts. Manual disarm is done.
Note: Any ignition-on action during while LED-ON will interrupt the procedure and it is necessary to repeat the whole process

from start.

Manual disarm by PIN code

1. During alarm trigger, turn the ignition to ON. Wait for the siren to stop blurting.
2. Then immediately turn ignition OFF-ON-OFF-ON-OFF and complete this process within 3 seconds. LED
will glows for 3 seconds.3 seconds later, LED will turn off .
3. When LED turn off, immediately turn ignition ON-OFF-ON-OFF-ON-OFF-ON and complete this
process within 3 sec. The LED will flashes 4 times.
4. Must turn off ignition again, and LED will start glows for 1.5 seconds, LED flash first time stand for
number one, flash second times its number Two, flash third times its number Three, flash fourth
times its number Four, flash fifth times its number Five.

EX: PIN code numbers are 1234, procedure as below.

(1) After LED flash first time, ignition immediately turn ON stand for input number1.
(2) Ignition turn off, LED will start flash again, after LED flash second time, ignition immediately turn ON stand for
input number 2.
(3) Ignition turn off, LED will start flash again, after LED flash third times, ignition immediately turn ON stand for input
number 3.
(4) Ignition turn off, LED will start flash again, after LED flash fourth time, ignition immediately turn ON stand for input
number 4.
If the number input has mistakes, the system still at arm mode and alarm trigger.
Note: Any ignition-on action during while LED-ON will interrupt the procedure and it is necessary to repeat the whole process
 from start.

Systems learning of new remotes codes

1. During disarm mode , turn ignition ON-OFF-ON-OFF-ON-OFF and stay it at OFF position to enter 1st stage, LED will glows for 3

seconds. 3 seconds later, LED will turn off .

2. When LED turn off, system enter 2nd stage. Immediately turn ignition ON-OFF-ON-OFF-ON-OFF-ON-OFF-ON and complete this

process within 5 sec. Ignition stay at ON position. The siren will sound 5 blurts and system will enter learn-mode.

3. Press and release newly remote button 1 whit 2 button simultaneously till the siren chirps 1 time

confirming code learning is completed.

4. Then other remote did process 3. To allow the main system learn coding of each transmitter. (Maximum 4 remotes can be learned

by the system)

5. The system will automatically jump out of learning mode if no signal is received within 6 sec. from the last signal or turn OFF

ignition.

Note: 1. Any ignition-on action during while LED-ON will interrupt the procedure and it is necessary to repeat the whole process

from start.

2. The pre-memorized coding will be erased each time the learning mode is activated. Re-do the code learning in this case

Reminder of allowed number of remotes

 Security reason. This allows you to know how many remotes are memorized up to date.

Turn ignition to ON position. Press and release button 3 of remote and observe LED flash pattern. For example 2 times

of flash Indicates that system has already learned 2 remote units.

Purpose: Allow car owner knows how many remotes are memorized up-to-date (Avoid others to make copy of the remote by using

original remote).

Hopping code technology

The hopping code technology is used in this system. This prevents code grabbers from counterfeiting to make a copy remote.

Monitoring standby indication

1. If the LCD shows icon antenna flashing, the remote is monitoring the car. Refer to LCD picture No.17

2. After 7 seconds from the system disarm, the remote stops monitoring and its antenna disappears from LCD

screen .

Low battery indicator for transmitter

When low battery icon displays on the remote LCD, its battery is about to exhaust. Insert the new battery. Refer picture to No.16
 Out-of-range feature
If remote sounds bu after any button is pressed, it is out of range from the motorcycle.

Remote Controls other Functions

The LCD remote control unit has basic features of (a) EL backlight (b) most power saving circuitry (c) audible or vibration

alert mode (d) different time indication of Real time, alarm clock, count-down timer and follow the procedure as

below

Buttons used in Adjustment procedural steps

Notes for quick adjustment
adjustment of time

Press 3 Backlight ON (automatic turn-off after few

sec)

Entry/exit of adjust mode by hour, confirmed While in each time entry mode:

by 2 beeps Press 1 to choose ON or

Press 3 1 time Minute entry (adjust mode) adjustment upwards

Press 3 2 times Hour entry (to adjust Alarm clock) Press and hold 1 for quick

Press 3 3 times Min entry (to adjust Alarm clock) adjustment upwards
Press 2 to choose OFF or adjust
Press 3 4 times ON/OFF choice for alarm clock
downwards
Press 3 5 times Hour entry (to adjust countdown timing
Press and hold 2 for quick
Press 3 6 times Min entry (to adjust countdown timing)
adjustment downwards
Press 3 7 times ON/OFF choice for countdown timing
Alarm module wiring diagram