Control Systems in Automobiles

Examples of Automotive Closed-loop

Control Systems
Control System Indirectly Directly Manipulated Sensor Actuator
controlled controlled variable
variable variable
Fuel injection Air-fuel Exhaust oxygen Quality of Zirconia or Titania Fuel injector
system ratio content injection fuel based electro-
chemical

Knock control Knock Knock sensor Ignition timing Piezo-electric Ignition coil
output accelerometer switch. Transistor

Anti-lock Wheelslip Wheelspeed Brake time Magnetic reluctance ABS solenoid

braking system limit pressure valve
ECU (based on Micro Computers)

Battery Power supply regulator

Analogue Analogue to
Motors
signals e.g. digital
transducer converter
signals and
multiplexer Micro- Output Solenoids
computer circuitry
Digital
Input Lamps, LEDs
signals e.g.
interfacing etc.
switch
states
 Engine Management Sensors
Measured variable Direct/indirect Sensor technology/ Sensor mounting
measurement reference location
Intake manifold absolute Indirect measurement Wheatstone bridge Within intake
pressure of engine load or arrangement of thick film manifold
mass air-flow intake resistors bonded onto a thin
alumina diaphragm

Mass airflow Direct and indirect Various forms including Within air intake
measurement of fuel flap type, hot-wire,
injector basic pulse Karman vortex and thick-
width film diaphragm

Temperature Direct measurement Thermistor or thermocouple Intake air, outside air,

at various locations depending on temperature catalytic converter,
range engine coolant,
hydraulic oil
Engine speed and Direct measurement Magnetic reluctance or Hall Flywheel on end of
crankshft reference effect device engine crankshaft
position
Engine Management Sensors (contd)

Measured variable Direct/indirect Sensor technology/ Sensor mounting

measurement reference location
Battery voltage Direct measurement Resistive attenuator

Throttle position Direct measurement Potentiometer Accelerator pedal

Knock (engine cylinder Direct measurement Piezoelectric accelerometer Cylinder block or

pressure oscillations type. head
during ignition)
Oxygen concentration in Direct measurement Zirconia or Titania based Exhaust manifold
exhaust gas (Lambda exhaust gas oxygen sensors (normal operation
sensor) above 3000 C)
 Chassis Control Sensors
Measured variable and Direct/indirect Sensor technology/ Sensor mounting
application measurement reference location
Wheelspeed and engine Direct measurement Magnetic reluctance or Hall Brake assembly and
speed, (ABS, TCS and effect device crankshaft flywheel
electronic damping) respectively

Steering wheel angle, Direct measurement Potentiometer or optical Steering shaft

(Electronic damping) encoder
Throttle position Indirect measurement Potentiometer Accelerator pedal
of vehicle accel.

Chassis and wheel Direct Piezo-electric accelerometer Engine compart-

acceleration, (electronic ment and wheel
damping) assembly
Brake system pressure Indirect measurement Flexing plate sensor with Brake master
(electronic damping) of vehicle decelerat- strain gauges mounted on cylinder
ion plate
Steering shaft torque Direct measurement Optical device relying on Steering shaft
(Electric power assisted steering shaft distortion
steering) under drivers twisting
action
 Safety and Onboard navigation
Measured variable Direct/indirect Sensor technology/ Sensor mounting
measurement reference location

Vehicle deceleration Direct measurement G sensor (Piezo-electric Single-point

(air-bag systems) accelerometer) electronic sensing,
location in
dashboard or
steering wheel
Wheelspeed and engine Direct measurement Magnetic reluctance or Brake assembly.
speed (Vehicle nav. Hall effect device
Systems)
 Electronic fuel injection (EFI)
allows precise and fast control of fuel injected
by control of the on-time period of the solenoid operated injectors
(spray nozzle) and plunger.
delivery pipe fuel pressure is maintained constant by a fuel pressure
regulator
opening and closing times of between 0.5 and 1 ms.
engine operating speed of 6000 rpm (10 ms revolution time)
injector on-time can be controlled between 1 and 10 ms.
 Power driver application

multi-point or sequential fuel injection, with one fuel injector near the intake valve
(or valves) of each cylinder.
At a device level, a fuel injector IC package
provides the high solenoid drive current required
Incorporates both over-voltage and short-circuit protection,
fault reporting diagnostic routines also included
Two types of EFI System ----- Speed-density EFI
inlet manifold absolute pressure (MAP) sensor has an important role
fuel injection opening period or pulse width is related directly to the
mass of air flowing into the engine as fuel-air ratio must be maintained
constant in steady-state operation
and the mass of air-flow is related to the manifold absolute pressure
by the equation
Vd nv Pi
ma
RTi
where Vd is the displacement of the cylinder,
nv is the volumetric efficiency or the fraction of Vd actually filled on
each stroke, [= f(speed)]
pi is manifold absolute pressure,
R is a constant and
Ti is the intake air temperature.
Mass air-flow EFI
direct measurement of the quantity of air drawn into the
engine (using an air-flow sensor (AFS)).
simple flap-type,
hot-wire and
Karman vortex devices,
Direct measurement is better than feed-forward control
in speed density EFI
(factors like variation in volumetric efficiency, engine
displacement due to speed and internal deposits need to
be taken care of ).
Both of these forms of EFI may be improved
exhaust gas oxygen sensor for closed-loop control of the
airfuel ratio.
if engine is to be controlled precisely airfuel ratio must
be controlled to within 1%.
only possible with closed-loop control,
 Closed-loop control of airfuel ratio
The objective of low exhaust-gas
emission levels
maintain the airfuel ratio at 14.7:1
[stoichiometrically / chemically perfect]
three-way catalytic converters to control
emission
 In a closed loop system
the fuel injection period computed by air intake measurement
is modified
Based on measured exhaust gas oxygen (EGO) content.
injection period modification factor between 0.8 and 1.2.
EGO tells whether < 1 or > 1
Closed loop system has a limit cycle frequency between 0.5 to 2
Hz
Pollutant emission as a function of relative airfuel ratio, l (Chowanietz, 1995)
 Electronic clutch control
To relieve pressing of clutch during gear
change
Throttle cable of accelerator pedal replaced by
closed loop control system
Accelerator pedal position sensor and servomotor
Connected to an ECU for the gear change process
 Block Diagram of an Automatic Clutch
and Throttle system
Throttle motor

Clutch release
Throttle
Electronic control unit cylinder pressure
position
feedback Solenoid control
signal

Throttle servo system Hydraulic power unit and

solenoid control valve
Accelerator pedal (operation clutch release
position sensor lever)

Gear lever load switch

Clutch release lever
position sensor
Gear position sensor

Gearbox input shaft

speed sensor

Engine speed sensor

Control of clutch engagement and disengagement

Improved safety
Prevention of engine starting when in gear
Inappropriate gear change
Integration of Transmission and Engine
Throttle position
ECUs
sensor
Throttle idle switch
Selector lever
Handshake signals position sensor
Water between ECUs Hold mode switch
thermosensor Stoplight switch
Throttle Engine Overdrive inhibit
position control Transmission switch
sensor unit control unit Automatic
Knock sensor transmission fluid
Airflow sensor Solenoi temperature sensor
Fuel injection
Intake air d valve Torque converter
thermosensor and ignition output speed
control
Engine r.p.m. timing Vehicle speed
signal Engine Transmission Engine r.p.m.
Atmospheric
pressure sensor
During gear change up
transmission ECU signals the engine management ECU
cut off fuel injection and
Signals TECU to allow gear change
During gear change down
TECU energizes signals E-ECU
Changes ignition timing a few degrees to reduce engine torque,
Signals TECU to allow gear change
In the end both systems return to independent operation.
Integration of engine management and transmission
control systems
the multi-way switch reports position of the selector lever
If the lever is not in either Park or Neutral when starting, operation of the starter motor is
inhibited
a warning buzzer sounded
The hold switch (push-button switch on the selector lever)
instructs the ECU to hold the transmission in a current gear ratio
useful in descending a hill.
The stoplight switch
When the brakes are applied and transmission is in a lockup condition,
the lockup clutch is then disengaged.
The overdrive inhibit signal (O/D) (from a separate cruise control unit)
prevents the transmission from changing into overdrive (fourth gear) if
cruise control is activated and
vehicle speed is more than a certain amount below the set cruising speed.
The Automatic Transmission Fluid (ATF) thermosensor
modify the line pressure at temperature extremes
To account for changes in fluid viscosity.
Atmospheric pressure
If above 1500 m (engine develops less power at high altitudes)
the automatic gear change points are modified to suit the change in performance.
 Powertrain Control System
Also includes
Exhaust gas
recirculation system
(circulating exhaust into
intake to reduce max
combustion temp, and
hence NOx)
Controlled by
powertrain ECU
Engine temp, load,
speed
Evaporative Emission
Control System (to
circulate fuel vapour
into intake and prevent
leakage into
atmosphere)
 Chassis Control Systems
Anti Lock Braking system
Electronic Damping Control system
Power Assisted Steering System
Traction Control Systems
Anti-lock braking systems (ABS)

The vehicle skids, the wheels lock and driving

stability is lost so the vehicle cannot be
steered;
If a trailer or caravan is being towed it may
jack-knife;
The braking distance increases due to
skidding;
The tyres may burst due to excessive friction
and forces being concentrated at the points
where the locked wheels are in contact with
the road surface;
 Variation of the coefficient of friction ( ) with slip ratio

Induction type wheel-speed sensors on the wheel assembly or differential

couple magnetically to a toothed wheel known as an impulse ring.
 Antiskid braking system (ABS)

All electronic signals come to the electronic controller (ECU)

The ECU controls the hydraulic modulator
To control the Brake line pressure in Brake master cylinder
Wheel-speed and braking pressure during ABS-controlled braking
If wheel decelerates beyond a certain level, curtail brake pressure (1)
If wheel decelerates further, reduce brake pressure further (2)
If wheel accelerates, increase brake pressure (3)
 Traction control systems
prevent drive wheels from wheelspinning during
starting or
accelerating on a wet or icy surface.
avoid reduction of either steering response in front-
wheel-drive (FWD) / vehicle stability on rear-wheel-
drive (RWD) vehicles.
TCS operates
to maximize adhesion to the road surface during
acceleration
Same sensors as in ABS
The actuation uses fuel, ignition and driven wheel
braking action
 Traction Control Systems (TCS)
to achieve reduction in driven wheel torque during wheelspin.
maintain the acceleration slip of the driven wheels equal to the
mean rotational velocity of the non-driven wheels + a specified
speed difference known as the slip threshold.
driven wheels are kept at a faster speed than the non-driven wheels
the vehicle accelerates at a constant rate proportional to the
difference in the two speeds. (if difference is not in limits (slip
threshold), traction needs to be controlled)
Control depends on road surface conditions or adhesion coefficient.
on dry road surfaces, maximum acceleration at slip rates of 10 to
30%.
On glare ice, maximum traction between 2 and 5 percent
so TCS systems designed for a slip rate range between 2 and 20%.
 Adhesion force coefficient A as a function of acceleration A(Jurgen, 1995)
on loose sand or gravel and in deep snow the coefficient of adhesion increases continually with
the slip rate
TCS systems incorporate slip-threshold switches to allow the driver to select a higher slip
threshold or switch off the TCS
The control objectives of TCS are modified by vehicle speed and curve recognition.
Both of these variables can be derived from the speeds of the non-driven wheels.
coefficient of adhesion or friction decided on the basis of acceleration rate and engine torque
The slip threshold is raised in response to higher friction coefficients to allow higher
acceleration rates
 Curve recognition or cornering detection also affects
the control strategy for TCS.
This strategy employs the difference in wheel speeds of
the non-driven wheel speeds as a basis for reductions
in the slip setpoint to enhance stability in curves.
High vehicle speeds and low acceleration requirements
on low coefficient of adhesion surfaces imply
a control strategy of progressively lower slip threshold
setpoints as the vehicle speed increases,
gives maximum lateral adhesion on the surface.
Electronic damping control
The primary function of a shock absorber
control vehicle movement against roll during turning and pitch during acceleration or braking.
Requires hard suspension

secondary role
To prevent vehicle vibration caused by a poor road surface.
Requires a soft suspension

Electronic damping control (EDC) used to attain these twin

objectives
altering the characteristics of spring and oil-filled damper
arrangement
difficult and expensive

Simple option - Suspensions with at least three settings; soft,

medium and firm
OR electronically controlled suspension systems using air,
nitrogen gas and hydraulic oil as a suspension agent.
 sensors used
vehicle speed,
engine r.p.m.,
brake system pressure,
steering angle,
chassis and wheel acceleration,
throttle position,
vehicle load and
even road surface condition
Road condition - implied by processing signals from front and rear height sensors
rather than direct measurement.
if the height sensor signals a small high frequency but a large low frequency amplitude
a heaving or undulating road surface
Does not require a softening of damper.
A large high frequency component would suggest
a rough road surface and
Softening of damper action.
Conflicts with damper requirement to prevent rolling during cornering.
If the vehicle corners on a rough surface this must be resolved by the ECU.
 Longitudinal acceleration
measured directly using an acceleration
sensor, or
inferred from brake system pressure and
throttle opening angle.
Used to control pitching during acceleration /
braking
lateral forces
inferred by the rate at which the steering
wheel is being turned and the vehicle speed.
used by the ECU to prevent rolling.
the actuators are dampers fitted with
two ON-OFF fluid control solenoids used
to select one of four different damper
settings (normal, soft, super-soft and
firm).
Driver can choose sport or smooth ride
mode.
In sport mode soft or super-soft damper Electronically controlled
damping system
settings excluded
Result in a harder but more stable ride.
Electronically controlled power-assisted steering (PAS)

Hydraulic bridge circuit for electronically-controlled power steering

showing flow paths
Electronically controlled hydraulic PAS
the ports of a solenoid valve are connected across the rack
and pinion steering hydraulic power cylinder.
with increasing vehicle speed the valve opening is extended
reducing the hydraulic pressure in the power cylinder
increasing the steering effort.
bridge-like restrictions for control of the power cylinder are
formed by the paths through the pump to port connections of
a rotary valve
The valve is connected directly to the steering wheel and
a small movement of this controls the high pressure hydraulic fluid to
reach the power cylinder/solenoid valve.
Electric PAS
input to the rack and pinion steering
system is from a motor/reduction gearbox
motor torque is applied directly to either
the pinion gear shaft or to the rack shaft.
The steering effort range is greater than
with hydraulic systems,
installations are cheaper and reliable.
Power is only consumed when steering
wheel moves, (unlike hydraulic system)
a torque sensor on the column shaft
The electric motor coupled to the worm
wheel mechanism through a reduction
gearbox.
The load torque TL on the steering column
is the load presented by the worm
mechanism and the rack and pinion
assembly to which it is attached.
 The amount of motor torque is proportional to the motor current IM.
in a simple armature controlled d.c. motor the average current is given
VM k N
IM
R
where R is the armature resistance,
N is the speed of the motor and VM the motor voltage,
the set point motor voltage depends on how much control effort is
required from the d.c. motor.
When a driver turning a steering wheel at a constant rate, say in cornering.
The d.c. motor, must turn at a speed proportional to this rate.
Controlling term --- motor voltage = k x N
at high vehicle speeds the assistance given to the driver must decrease in
proportion to speed
i.e., Decrease motor current or voltage as vehicle speed increases.
Motor voltage component = kT x Tm (Tm is output from Torque sensor)
Inverse function of vehicle speed
Add both components to get appropriate control
Air-bag and seat belt pre-tensioner systems

systems consist of
crash detection sensors (typically piezoelectric) with a signal conditioning amplifier
a microcontroller distinguishing between crashes and normal vehicle dynamics,
igniter triggering for the pyrotechnic inflator
used for air-bag deployment and seat belt tightening.

The allowable forward passenger travel with an air-bag system is 12.5 cm

with seat belt tensioning systems it is about 1 cm.
Approximately 30 ms are required to inflate air-bags and
time required to tension a seat belt with a retractor = ~10 ms.
triggering must be done by the time forward displacement is reached
minus the activation time of the respective restraining device.
Often multiple sensors and sensor mounting positions
When airbag is triggered
ECU turns on the firing current switches,
allows current through the igniter,
initiates a gas generation reaction inside the inflation module.
Capacitance based power maintained even if battery is disconnected
 Ignition Energy
reserve Power device and
SMARTMOS
Power supply
Accelerometer

Crash Sensor Crash

sensor (s) interface(s) discrimination Firing
current Igniters
switches
Discrete Deployment
inputs management
Diagnostic
interfaces
Safing/ Data recording and
arming
protection
devices
Fail Diagnostics Output Warning and
Side bag
safe management interfaces displays
interfaces
(optional)
Serial SMARTMOS ICS
To external peripherals
communications

Microcontroller

Air-bag electronics block diagram